Panasonic UT-201 mounting kit
Contents
1. Front Fences and centered on the tray Latch both Side Trays by pushing in until a click is heard a S Configuration continued 7 While holding tablet in position carefully flip the UT 201 over and adjust the Rear Tray inward until the Rear Fence contacts the tablet Ensure contact is maintained with Front Fences Retighten Rear Tray Adjustment Screws Torque screws to 22 in lbs 0 25 Nm 10 8 Loosen Side Tray Adjustment Screws and push in the Side Trays equally until contacting both sides of tablet Retighten Side Tray Adjustment Screws Torque screws to 22 in lbs 0 25 Nm 10 www havis com 1 800 524 9900 Configuration continued 9 Carefully flip the UT 201 amp tablet over and adjust the 4 Side Hold Down Lugs vertically until firm contact is achieved with tablet NOTE To verify proper set up pull Latch Handle to ensure Side Trays release fully om 10 If required to prevent blocking a crucial port or control the Rear Fence can be adjusted along the length of the tablet Loosen Rear Fence Adjustment Screw and slide Rear Fence laterally or remove the Rear Fence Adjustment Screw and move the Rear Fence to one of the outer slots Retighten Rear Fence Adjustment Screw Torque screws to 22 in lbs 0 25 Nm 10 11 If tablet or protective cover is changed and you need to reconfigure your Universal Tablet Mount follow the Configuration instructions starting on Page 4 of this Owne2. DS DA 503 3 Replacement Keys Se your of two 2 replacement keys for your Universal Tablet Mount Havis Inc 75 Jacksonville Road PO Box 2099 Warminster PA 18974 47801 Anchor Court Plymouth MI 48170 www havis com 1 800 524 9900 01 2008 UT 201_OMN _12 12
3. Owner s Manual Havis Universal Tablet Mount H VIS www havis com Ay 1 800 524 9900 Productivity in motion Before Beginning Original Instructions Havis is pleased to provide this Owner s Manual to aid in the proper installation and use of the UT 201 Universal Tablet Mount For questions regarding the set up of your UT 201 Universal Tablet Mount please contact Havis at 1 800 524 9900 or visit www havis com for additional product support and information This Owner s Manual applies to the following Part Numbers UT 201 e NEVER STOW OR MOUNT THE UT 201 DIRECTLY IN A VEHICLE AIRBAG DEPLOYMENT ZONE e DO NOT USE TABLET WHILE DRIVING e READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION Table of Contents Specifications lt isca csiva cause iein en ent ovate A SE A NETRE 2 Parts Included sesiis eo paaa e A AE 3 GONMBUATION s Sease e a E A T NEES 4 Installation esee E aegis eee ee 9 Cable Managem nt oaoaraa ii Ear AE NEEE aE de EATER EAREN 10 Operati Masne eea a E E a Reve a ea bia 11 Specifications Universal Tablet Mount Dimensions Overall Dimensions 10 4 26 4cm W x 8 4 21 3 cm D x 2 3 5 8 cm H Weight 2 6 Ibs 1 2 kg Compatible Tablet Dimensions Width 9 30 23 6 cm to 11 24 28 5 cm Depth 6 83 17 3 cm to 8 13 20 79 cm Height 0 55 1 4 cm to 0 93 2 4 cm HAVIS Parts Included Universal Tablet Mount Top View a latch Releas
4. e Handle tock fe Frontrenes c Bottom View T side Tray Adjustment screws az DE Adjustment Screws x4 r Mounting Holes vn aa L Strain Relief Holes x4 m Kensington Lock Holes x2 Hardware Kit i 2 3 a d This Hardware Kit includes 1 Zip Ties 2 2 Integrated Zip Ties 4 5 wo 3 Pan Head Screws M4 x 0 7 x 12mm long 5 4 L shaped Wrench 1 Mounting Spacers 4 6 Keys 2 ul D oO M oO www havis com 1 800 524 9900 Configuration 1 Ensure the UT 201 Universal Tablet Mount is latched by pushing inward on both Side Trays Trays should be up against top surface as shown e anmenn e sn 2 Turn the UT 201 over and loosen both Side Tray Adjustment Screws and fully extend both Side Trays HAVIS Configuration continued Retighten both Side Adjustment Screws and unlatch the Side Trays by pulling out the Release Handle Loosen both Rear Tray Adjustment Screws and fully extend the Rear Tray DO NOT REMOVE SCREWS www havis com 1 800 524 9900 Configuration continued 5 Before fitting your tablet on the UT 201 make sure you turn the tablet s power off and remove any connected cords or peripherals ww ww ww 6 Choose the best orientation of tablet to prevent Front Fences and Side Hold down Lugs from blocking access to crucial ports or controls Next place tablet onto the UT 201 and ensure it is in contact with both
5. ieve wires cables Loop and tighten Zip Tie around wires cables as required Operation 1 Before placing your tablet into your Universal Tablet Mount and before taking your tablet out of your Universal Tablet Mount unlatch by pulling out the Latch Handle extending each of the two Side Trays 2 Place Tablet in center of unlatched Universal Tablet Mount ensuring the tablet is touching both Front Fences as well as the Rear Fence then push inward on both Side Trays until a click is heard 3 For theft deterrence secure tablet by locking the Universal Tablet Mount with the supplied Key Hardware Kit Item 6 Secure the Universal Tablet Mount by utilizing a Kensington Lock in either of the provided holes on the bottom h ASAMA www havis com 1 800 524 9900 A AVIS LTS Related Products Havis offers a wide variety of accessory products for use with the UT 201 Universal Tablet Mount For more information or to order please visit www havis com DS DA 218 Desktop Stand Durable stand for mounting the Universal Tablet Mount in the home or office UT 201 KIT 1 Replacement Hardware Kit Unversal Tablet Mount replacement hardware kit includes all components necessary to replace any Lug Fence Screw or Wrench UT 201 KIT 2 Tall Lug Kit Tall Lug Kit replaces the standard Side Hold down Lugs equipped with your Universal Tablet Mount in order to fit taller tablet models
6. r s Manual EA HAVIS Installation The Universal Tablet Mount uses a VESA 75mm hole pattern for mounting For additional technical support with mounting the UT 201 in your specific work environment please contact Havis at 1 800 524 9900 1 Because the UT 201 was designed to accommodate a wide variety of work spaces four 4 Mounting Spacers Hardware Kit Item 5 have been provided for use in mounting applications which require them Slip the Mounting Spacers over the top of each Mounting Hole before aligning with desired mounting surface Mounting Holes 2 Align the four holes on the mounting surface with the four Mounting Holes on the bottom of the UT 201 Secure Universal Tablet Mount to the mounting surface using four Pan Head Screws Hardware Kit Item 3 Torque screws to 36 in Ibs 0 4 Nm 10 seme 8 Pan Head Screws Hardware Kit item 3 Mounting Surface Havis Desktop Stand option shown Part DS DA 218 www havis com 1 800 524 9900 v Cable Management 1 If it is necessary to strain relieve wires cables insert Integrated Zip Ties Hardware Kit Item 2 into any of the Strain Relief Holes on the bottom of the UT 201 Loop and tighten Zip Tie around wires cables as required A 2 Additional Strain Relief Holes have been provided on each of the four corners of the UT 201 If necessary use these holes along with the provided Zip Ties Hardware Kit Item 1 to strain rel
Download Pdf Manuals
Related Search