Mobotix HaloMount
Contents
1. HaloMount Quick Install A The HiRes Video Company MOBOTIX Installation Mount For S14D S15D Sensor Modules MX HALO EXT CM CO NG PW SW e Suitable for all sensor modules e Inner ring can be tilted 20 e High quality metal design e Design variety with five colors 31 764 EN_V1_06 2013 The MOBOTIX accessory HaloMount offers the possibility to integrate the sensor modules of a FlexMount Dual camera in an installation mount that can also be used for lighting equipment QR CBC MRI16 LED Sharp Array 4 6 W Since the sensor module can be tilted up to 20 you can point the image center precisely on the area that is to be monitored Note The HaloMount is not suited for unprotected outdoor usage Material steel inner ring brass surface powder coated or galvanized colors matt chrome chrome brushed nickel white black installation diameter 68 mm Delivered Parts 1 1 Item Number Part Name Outer ring with spring clip w o Light connection cable not image needed for sensor module Installation Before installing the sensor modules make sure that the sensor cables will reach the intended mounting position without placing a strain on the cables Disconnect the sensor modules from the sensor cables before installing the modules Cables with straight or with angled plugs can be used to connect the sensor modules on the camera straight plugs only Further information on the connectors and the install2. 2 Replace sensor module Remove the sensor module of the inner ring and disconnect it from the sensor cable turn bayonet catch to the left and remove it then remove the sensor cable Connect the new sensor module to the sensor cable insert sensor cable attach bayonet catch and turn it to the right 3 Insert sensor module into inner ring Insert the new sensor module into the inner ring 4 Insert inner ring into HaloMount Turn the inner ring in such a way that the two notches are positioned above the two retaining collars in the outer ring Engage the inner ring holding the sensor module into the HaloMount by applying slight pressure 5 Adjust sensor module and camera image Adjust the sensor module and the camera image as described in steps 10 and 11 in Installation Copyright MOBOTIX AG 2013 Made in Germany e Technical information subject to change without notice HiRes Video Innovations The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its decentralized concept has made high resolution video systems cost efficient MOBOTIX AG D 67722 Langmeil Tel 49 6302 9816 0 Fax 49 6302 9816 190 info mobotix com
3. ation can be found in the S14 S15 manual 1 Prepare opening Prepare a circular opening with a diameter of j 68 mm with a holesaw 2 Attach hinged ferrite Attach a hinged ferrite to the sensor cable maximum ad distance to the connector 10 cm oo 3 Lead sensor cable through the opening Lead the sensor cable through the opening in the ceiling and allow it to protrude through the longer it extends the easier the installation 4 Loosen inner ring of the mount Loosen the inner ring fixed using a spring mechanism by gripping it from the inside and moving it beyond the maximum tilt angle moderate pressure is sufficient 5 Remove lock nut If a lock nut is attached to the sensor module remove it The lock nut is not needed for the installation of the HaloMount 6 Insert sensor module into inner ring Insert the sensor module into the dismantled inner ring of the HaloMount from behind HiRes Video Innovations The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its decentralized concept has made high resolution video systems cost efficient MOBOTIX AG D 67722 Langmeil Tel 49 6302 9816 0 Fax 49 6302 9816 190 info mobotix com e v x Q e E 3 3 3 2 HaloMount Quick Install A z se v x Q e E 3 3 3 The HiRes Video Company MOBOTIX 7 Insert sensor module into outer ring Insert the inner ring with th
4. e sensor module into the outer ring from below Turn the inner ring in such a way that the two notches are positioned above the two retaining collars in the outer ring Engage the inner ring holding the sensor module into the outer ring by applying slight pressure 8 Connect sensor module Connect the sensor cable to the sensor module Turn the blue bayonet catch to the left and remove it Remove the plug then insert the sensor cable attach the bayonet catch and turn it to the right 9 Insert HaloMount into opening Push the two spring clamps of the outer ring upwards and insert the HaloMount into the opening Note that the position of the two spring clamps determines the position of the inner ring s swivel axis and therefore the final position of the sensor module 10 Adjust sensor module The inner ring can be tilted up to 20 without the use of tools thus you can focus the sensor module optimally on the area to be monitored 11 Adjust camera image For proper adjustment of the camera image use the black module wrench provided with the camera Use the wrench to turn the sensor module in either direction until the desired position is shown on the computer monitor Replacing Sensor module All MOBOTIX sensor modules can be mounted in the HaloMount housing 1 Loosen sensor module Tilt the inner ring up to the stop and press hard on one side of the ring s edge to loosen the inner ring of the HaloMount
Download Pdf Manuals
Related Search