Philips 2900 series 22PFL2978H 22" Full HD Black
Contents
1. Progressive JPEG max WxH 9600x6400 3840000bytes bmp max WxH 9600x6400 3840000bytes English 9 PHILIPS All registered and unregistered trademarks are the property of their respective owners Specifications are subject to change without notice Philips and the Philips shield emblem are registered trademarks of Koninklijke Philips Electronics N V and are used under license from Koninklijke Philips Electronics N V 2013 TP Vision Netherlands B V All rights reserved www philips com 282. long time for 22PFL2978H 12 only for 22PFL2978K 12 only TV scroll button The TV Scroll button on the side of the TV allows you to control the volume change channels and put the TV into standby a 2 To change volume Increase the volume by scrolling up Decrease the volume by scrolling down To change channel 1 Press the middle of the scroll button the channel information banner will appear on screen 2 Scroll through the stored channels by pushing the button up or down To change source 1 Press the middle of the button twice the source list will appear on screen 2 Scroll through the available sources by pushing the button up or down To switch the TV to standby Press the middle of the button down and hold it down for a few seconds the TV will turn into standby mode Connecting power Power Adapter connection The TV set is designed to operate on 12 V DC For this an adaptor is used which gives 12 V voltage Connect this adaptor to a system that supplies 110 240V AC 50 60Hz Cigarette lighter plug connection Connect the cigarette lighter plug cable to the cigarette lighter socket of your car or a cable with clips to the battery of car making sure to observe the correct polarity Plug the other side of 12 volt cable to DC 12 socket at the back of the TV Then the standby LED lights up V V ATTENTION 12 V Input Switching on off To switch the TV on To switch on
3. software version Note If the TV fails to come on after the upgrade unplug the TV for 2 minutes and plug in again Troubleshooting TV will not turn on Make sure the power cord is plugged in securely to wall outlet The batteries in the remote control may be exhausted Press the Power button on the TV Poor picture Have you selected the correct TV system e Low signal level can cause picture distortion Please check antenna access e Check if you have entered the correct channel frequency if you have done manual tuning e The picture quality may degrade when two devices are connected to the TV at the same time In such a Case disconnect one of the devices No picture e No Picture means that your TV is not receiving a transmission Have you selected the correct button on the remote control Try once more Also make sure the correct input source has been selected Is the antenna connected properly Is the antenna cable damaged Are suitable plugs used to connect the antenna If you are in doubt consult your dealer No sound Has the TV been set to mute To cancel mute press the ot button or increase the volume level Sound is coming from only one speaker Is the balance set to one extreme See Sound Menu section Remote control does not operate e The batteries may be exhausted Replace the bateries Input sources can not be selected If you cannot select an input source it is p
4. the TV from standby mode either Press the dy button CH or CH or a numeric button on the remote control e Press the side function switch until the TV comes on from standby Note If the TV has been left on and not been operated for a while the TV will go into standby When you next switch on the following message will be displayed Standby Cause No Operation Press OK to continue To switch the TV off e Press the r button on the remote control or press the side function switch until the TV switches into standby mode Note To power down the TV completely unplug the power cord from the mains socket First time installation You will see the language selection screen when you first turn on your TV Select your preferred language and press OK followed by the selection Home Mode Shop Mode You can set up your TV by following the First Time Installation FTI screen with the following selections Aerial installation Select the AERIAL option from the Search Type screen to search for terrestrial digital TV broadcasts Optional a channel list which is generated by LCN will be displayed on screen when the search is over Select Yes and press OK to store this list Press button to quit channel list and watch TV LCN is the Logical Channel Number system that organizes available broadcasts in accordance with a recognizable channel sequence if available English 3 Media br
5. 0 60 O Receiving Channels VHF BAND 1 11 UHF BAND EXT NTSC 60 O eo Paella SCART RGB 50 O calco Preset 1000 for 22PFL2978H 12 RGB 60 O 10000 for 22PFL2978K 12 rt PAL 50 60 O Channel Indicator On Screen Display ide i NTSC 60 O RF Aerial Input 75 Ohm unbalanced 4801 480P 60Hz O Operating Voltage 110 240V AC 50 60 Hz 5761 576P 50Hz O Audio German Nicam Stereo ED 720P 50Hz 60Hz O Audio Output Power 2x2 5 W r WRMS 10 THD 10801 50Hz 60Hz O us 1080P 50Hz 60Hz O Power Consumption 47 W 4801 60Hz o Weight ia 480P 60Hz O TV Dimensions DxLxH 134 x 516 x 352 with foot 5761 576P 2082 o TV Dimensions DxLxH 35 x 516 x 317 HDMI1 720P 50Hz 60Hz O without foot HDMI2 A 10801 50Hz 60Hz O Display 16 9_22 inch 24Hz 25Hz Operation 5 C up to 45 C 85 humidity 1080P 30Hz 50Hz O temperature and max 60Hz operation humidity for 22PFL2978K 12 only English 7 dat mpg MPEG1 2 Layer 1 2 3 AAC HEAAC 1080P 30fps 50Mbit mpeg AC3 EAC3 LPCM ADPCM sec MPEG2 H 264 VC1 AVS MPEG1 2 Layer 1 2 3 AACIHEAAC H 264 1080Px2 25fps MVC AC3 EAC3 LPCM ADPCM 1080P 50fps MVC 1080P 24fps Other 1080P 30fps 50Mbit MPEG2 MPEG1 2 Layer 1 2 3 AC3 LPCM 1080P 30fps SOMbit sec MPEG1 2 4 XviD MPEG1 2 Layer 1 2 3 AAC HEAAC H 264 1080Px2 25fps H 264 AC3 EAC3 LPCM 1080P 50fps Other 1080P 30fps VETLVVMVS 50Mbit sec Motion JPEG MPEG1 2 Layer 3 AAC HEAAC H 264 AC3 EAC3 LPCM AD
6. Direct another menu screen will be displayed Select an available satellite by using cursor left or cursor right after your selection you have 2 possibilities to continue installation a full or a quick installation 1 Press the green button and select NO followed by OK to perform a full scan and search for all available services on the selected satellite 2 Press the green button and select YES followed by OK to load a predefined channel list and confirm with very quick installation all main services per country installed Unicable If you have multiple receivers and an unicable system select this antenna type Press OK to continue Configure settings by following instructions on the screen For full or quick installation follow the instructions under Direct File playback will continue randomly and random playback will continue DiSEqC switch If you have multiple satellite dishes and a DiSEqC switch select this antenna type After selecting DiSEqC switch another menu screen will be displayed You can set four DiSEqC options if available Press GREEN button to scan all satellites or press YELLOW button to scan only the highlighted satellite To save and exit press OK button Play media files from a USB drive You can play photo music and movie files stored on a USB disk by connecting itto your TV Connect a USB disk to one of the USB inputs located on the side of the TV Press
7. PCM 1080Px2 25fps 1080P 50fps Other 1080P 30fps 50Mbit sec MPEG1 2 4 MPEG1 2 Layer 1 2 3 AACIHEAAC H 264 Xvid AC3 EAC3 LPCM ADPCM WMA 1080Px2 25tps 1080P 50fps Other H 264 1080P 30fps VC1 WMV3 50Mbit sec Sorenson H 263 Motion JPEG H 264 MPEG1 2 Layer 3 AAC HEAAC H 264 1080Px2 25fps Sorenson H 263 LPCM ADPCM 1080P 50fps Other 1080P 30fps SOMbit sec MPEG4 H 264 1920x1080 30P 20Mbit sec asf wmv MPEG2 4 XviD H 264 MPEG 1 2 Layer 1 2 3 AAC HEAAC 1080P 30fps 50Mbit VC1 WMV3 AC3 EAC3 LPCM WMA sec MPEG Layer 1 2 3 MP3 A WMA ASF WMA WMA Pro PF m a aac AAC HEAAC 4 jpg jpeg Baseline JPEG MAX WxH 14592x12288 Progressive JPEG Up to 8 MegaByte non interlace interlace English 8 Supported file formats in USB mode for 22PFL2978H 12 PE Format Remarks A Video Audio Maximum resolution Bit rate etc MPEG Layer 1 2 13 mpg mpeg MPEG1 2 dat vob MPEG1 2 MPEG2 H 264 MPEG1 2 4 MPEG4 Xvid 1 00 mp4 Xvid 1 01 Xvid 1 02 Xvid 1 03 MAX 1920x1080 30P 20Mbit sec Xvid 1 10 beta1 2 PCM MP3 H 264 MPEG2 MPEG4 Xvid 1 00 Xvid 1 01 Xvid 1 02 Xvid 1 03 Xvid 1 10 beta1 2 H 264 MPEG 1 Layer 1 32Kbps 320Kbps Bit rate mp3 12 MP3 32KHz 48KHz Sampling rate jpg jpeg Baseline JPEG max WxH 15360x8640 4147200bytes MPEG2 EAC3 AC3 mkv avi PCM
8. Register your product and get support at www philips com welcome 22PFL2978H 12 User manual Mode d emploi Manuale utente Manual del usuario Manual do utilizador Gebruikershandleiding PHILIPS Contents Importants sisisi irssi isis odaia Use your TV Remote CONtrOl sainse cides conevsueavsinscvendscnesscdenriarss 2 Notifications features and accessories 3 Energy efficiency ccccccceeeseeeeeeeeeeteeeeeeeenes 3 TMSCION DUNO Tison 3 C nnecting POWET sassari 3 SWIHCNING OM OT asco 3 First meinstallatiO i r 3 Media browser MENU ssssseorrseorrssorrsrorsrnnnrssnr nro rr 4 Cable installation A Satellite installation sssnsss ssesrrssoressonersnrrnnnnrnr 4 Play media files from a USB drive s sssssssrsserssrnes 4 Recording a PrOMAMerccociidn lic 4 Timeshift recording ocio tranca 5 instant rec rdihg rires 5 Watch recorded programs su smmmesrrsssorrrserrsnrrrsnnrn 5 Change TV SettingS s sscssi5ssesssnisasanseskenssssberssnde 5 Display Options otitis 5 SOUNG OPlIOMS cuida 5 Configuring parental SettiNQS sesss000000 5 Electronic program guide EPG cceeeee 5 PrograMiOpliON Sicuani rin 6 Update your TM eis eres erstnceeesteeee 6 Troubleshooting ssssssssessssessrsssrsssnnrsnnsrnnn rann anna 6 Specifications oi 7 Important Read and understand all information in the accompanying Safety booklet before you install and use your T
9. SE button while watching recorded programs the slow forward feature will be available You can use PP button to slow forward Pressing PP button consecutively will change slow forwarding speed Change TV settings To access the options listed below 1 Press the Menu button 2 Highlight your selection 3 Press OK to confirm Display options Mode Changes the picture mode to one of the following Cinema Game Sport Dynamic and Natural for 22PFL2978K 12 only Contrast Sets the light and dark values of the image Brightness Sets the brightness value of the image Sharpness Sets the sharpness value A high sharpness value may result in a clearer crisper image depending on the content Color Sets the color value Backlight Controls the brightness of the backlight Noise reduction Reduces the noise level in the image Sound options Volume Adjusts volume level Equalizer Changes the equalizer mode Balance Adjusts whether the sound is coming mainly from the right or left speakers Headphone Sets headphone volume Sound mode Sets the preferred sound mode AVL Sets a limit to maximum volume output Headphone Lineout for 22PFL2978K 12 only This option is set to headphone if you have headphones or lineout if you have external amplifier connected to the headphone jack Dynamic bass Enables or disables the Dynamic Bass Increases the range of bass Surround sound for 22PFL2978K 12 only Surrou
10. V If damage is caused by failure to follow these instructions the warranty does not apply Disposal of old Equipment and Batteries Please do not disposed this TV or battery as general household waste If you want to dispose this product or battery please consider the collection systems or facilities for appropriate recycling Notice The sign Pb below the symbol for batteries indicates that this battery contains lead E Products Battery English 1 Use your TV Remote control PHILIPS NOTE The Remote Control range is approximately 7m 23ft Teletext Press TEXT button to enter Press again to activate mix mode Press once more to exit Follow the instructions displayed on digital teletext screen Digital teletext for UK only Press TEXT button to view digital teletext information Operate it with the colored buttons cursor buttons and OK button The operation method may differ depending on the contents of the digital teletext Follow the instructions displayed on digital teletext screen 1 Standby 2 Stop in Media Browser mode Play in Media Browser mode Play Slideshow in Media Browser Rapid reverse in Media Browser mode AV Source selection TV Electronic program guide in DVB channels 8 Navigation buttons Up Down Left Right 9 Program recording 10 Program Down Page up 11 Mute 12 Volume Down 13 Green button List Sch
11. edule in EPG Tag Untag All in favorite list 14 Red button 15 Numeric buttons 16 Subtitle on off in DVB channels 17 Teletext Mix in TXT mode 18 Blue button Edit Channel List Filter in Favorite List and EPG 19 Yellow button Timeline Schedule in EPG 20 Volume Up 21 Program Up Page down 22 Back Return Index page in TXT mode Swap 23 Mono Stereo Dual I II Current Language in DVB channels 24 Okay Confi rm Hold in TXT mode Channel List 25 Info Reveal in TXT mode 26 Menu on off Exit in Media Browser mode 27 Picture zoom 28 Rapid advance in Media Browser mode 29 Pause in Media Browser mode Time shift recording o oOo o gt English 2 Notifications features and accessories Energy efficiency This TV is designed with energy efficieny features e Power save mode ECO or On Off You can apply a combination of energy saving picture settings While you watch TV press the Menu button and the Power Save Mode settings can be found in the Picture section of the Main Menu Picture off mode If you only want to listen to audio from the TV you can switch off the display Other functions continue to operate normally While you watch TV press Menu and select Picture and from there select Picture off under the Power Save Mode option Note Disconnect your TV from the mains plug in case your TV is going to be inactive for a
12. ing the Bal button while in the Media Browser mode will access the Picture Sound and Settings menu options Pressing the B button again will exit from this screen You can set your Media Browser preferences by using the Settings Menu IMPORTANT Back up your files before making any connections to the TV The manufacturer will not be responsible for any file damage or data loss Certain types of USB devices for example MP3 players or USB hard disk drives memory sticks may not be compatible with this TV Recording a program Please format your USB flash drive device before first use To do this press OK while Format Disk is highlighted on screen and enter your pin number The factory default pin number is 0000 e To record a program connect a USB flash drive while your TV is turned off Recording function will be available once your TV is switched back on e The connected USB flash drives devices must have at least 1 gigabytes 1gb of free space and USB 2 0 compatibility An error message will be displayed if these conditions are not met By default recorded programs are stored on the connected USB flash drive device You may store these programs on a computer as well although you can play them only on your TV e The TV supports FAT32 and NTFS disk formatting but recording will not be available with NTFS formatted disks English 4 Timeshift recording Press PAUSE while watching a broadcast to activa
13. nd sound mode can be changed as On or Off Digital Out Sets digital out audio type Configuring parental settings This feature is for restricting access to selected content It is controlled by a pin number defined by you Factory default is 0000 Menu lock optional Menu lock setting enables or disables the menu access Maturity lock optional When set this option gets the maturity information from the broadcast and if this maturity level is disabled disables access to the broadcast Child lock optional When Child Lock is set the TV can only be controlled by the remote control In this case the control panel buttons will not work Set PIN Defines a new PIN number Note If the Country option is set to France you can use 4725 as the default code Electronic program guide EPG Some but not all channels send information about the current and next programs Press the view the EPG menu Up Down Left Right Navigate EPG OK Displays program options INFO Displays in detailed information on the program selected button to English 5 GREEN Switches to List Schedule EPG YELLOW Switches to Timeline Schedule EPG BLUE Displays filtering options tit The TV will start to record the selected program You can press again to stop the recording Program options In EPG menu press the OK button to enter the Event Options menu Select Channel In EPG menu using this option
14. ossible that no device is connected if not Check the AV cables and connections if you have tried to connect a device Recording unavailable To record a programme you should first connect a USB disk to your TV while the TV is switched off You should then switch on the TV to enable recording feature If you cannot record try switching off the TV and then re inserting the USB device USB is too slow If a USB is too slow message is displayed on the screen while starting a recording try restarting the recording If you still get the same error it is possible that your USB disk does not meet the speed requirements Try connecting another USB disk English 6 Specifications PC input typical display modes The following table is an illustration of some of the typical video display modes Index Resolution Frequency 1 640x350p 60 Hz 2 640x400p 60 Hz 3 1024x768 60 Hz 4 1280x768 60 Hz 5 1360x768 60 Hz 6 720x400 60 Hz Y 800x600 56 Hz 8 800x600 60 Hz 9 1024x768 60 Hz 10 1024x768 66 Hz 11 1280x768 60 Hz 12 1360x768 60 Hz 13 1280x1024 60 Hz 14 1280x960 60 Hz 15 1280x1024 60 Hz 16 1400x1050 60 Hz 17 1600x1200 60 Hz 18 1920x1080 60 Hz AV and HDMI signal compatibility Source Supported Signals Available TV Broadcasting PAL B G D K K PAL 5
15. owser menu Loop Shuffle Mode Operation Start playback with gt and activate TV plays next file and loop the list Start playback with OK and activate File will be played in a loop repeat Start playback with OK gt and activate File will be played in a shuffle Start playback with OK gt and activate Cable installation Select CABLE option and press OK on the remote control For automatic installation in case your Cable network supplier supports a Network ID based installation e g Unitymedia select YES in following screen and press OK In case your Cable network supplier does not support a Network ID based installation please select NO press OK and follow the instruction on the screen You can also select frequency ranges from this screen Enter the frequency range manually by using the numeric button Note Searching duration will change depending on the selected search step Satellite installation If you select Satellite option from the Search Type screen you can set a satellite and watch satellite channels When you select Satellite installation Antenna Type menu will be displayed There are three types of antenna selection You can select Antenna type as Direct Unicable or DISEqC switch by using or P buttons It is for 22PFL2978K 12 only Direct If you have a single receiver and a direct satellite dish select this antenna type After selecting
16. te timeshifting mode e In timeshifting mode the program is paused and simultaneously recorded to the connected USB disk Press gt PLAY button again to resume the paused program from where you stopped Press the STOP button to stop timeshift recording and return to the live broadcast Note Time shift cannot be used while in radio mode Note You cannot use the time shift fast reverse feature before advancing the playback with the fast forward option Instant recording Press Hit button to start recording an event instantly while watching a program You can press E button on the remote control again to record the next event on the EPG In this case an OSD will be displayed indicating the programed events for recording Press E STOP button to cancel instant recording Note You cannot switch broadcasts or view the Media Browser during the recording mode While recording a program or during the time shifting a warning message appears on the screen if your USB device speed is not sufficient Watch recorded programs Select the Recordings library from the Media browser menu Select a recorded item from the list if previously recorded Press the OK button to view the Play options Select an option then press OK button Note Viewing main menu and menu items will not be available during the playback Press the Ill STOP button to stop a playback and return to the Recordings Library Slow forward If you press Ill PAU
17. you can switch to the selected channel Record Delete record timer After you have selected a program in the EPG menu press OK Select the Record option and press OK After this operation a recording will be scheduled for the selected program Set Timer Delete timer After you have selected a program in the EPG menu press OK Select the Set Timer on Event option and press OK You can set a timer for future programs Update your TV Navigate on your main menu choose settings the version of the current software is displayed Caution Do not install a lower version of software than the current version installed on your product TP Vision cannot be held liable or be made responsible for problems caused by a software downgrade Update with USB Before you update the software make sure that you have A USB storage device that has at least 256 megabytes of storage space is FAT or DOS formatted and has its write protection disabled e Access to a computer with a USB connector and Internet access Navigate to www philips com support and follow the software update instructions Automatic update from digital broadcast While the TV is connected to an aerial signal If Automatic scanning in the Upgrade Options menu is enabled the TV wakes up at 03 00 and searches broadcast channels for new software upgrades If new software is found and downloaded successfully the next time the TV powers up it will have the new
Download Pdf Manuals
Related Search