Chief LVM3X3U flat panel floorstand
Contents
1. Figure 20 Installation Instructions LVM Series Adjustments Additional Cable Management Options 2 Cables may be routed through tops of columns and out Height Adjustment through the back cable management hole See Figure 23 1 Use upper knob on back of interface brackets AA and BB to adjust the height of each display See Figure 21 NOTE Adjust both brackets in order to maintain a level mount Plumb Adjustment 2 Use middle and lower knobs on back of interface brackets AA and BB to make plumb adjustments to each display See Figure 21 display not shown for clarity Ln R EL DO E I AEA I Figure 23 Figure 21 3 If rails needed to be installed on top of cable management holes cables may be routed through quick connect bases Cable Management Q prior to the rails being installed See Figure 24 1 Route cables from displays through nearest holes on front 4 Install rails according to Rails Installation section making of columns and out through back cable management hole sure cable is routed through cable opening on quick See Figure 22 connect base Q See Figure 24 NOTE For best access route display cables through columns prior to display installation See Cable Management yg 7 section for details e2. Figure 12 8 Hang rails K or L into screws installed in previous step to quick connect bases Q See Figure 12 IMPORTANT If installing the triple display rail L install rail to left and center columns so that add on rail can be installed to right column See Add On Rail Installation section for details 9 Install two 5 16 18 x 3 4 button head flange screws HH into the lower holes on each quick connect base Q to secure rails to quick connect bases See Figure 13 10 Tighten all 5 16 18 x 3 4 button head flange screws HH HH x2 Figure 13 13 LVM Series Installation Instructions Add On Rail Installation LVM3X2U LVM3X3U only 1 Install add on rail KK to right column following instructions in Rails Installation section 2 Use three 10 24 x 1 1 2 flat head cap screws Z to attach each add on rail KK to display rail L See Figure 14 SS Figure 14 Display Installation 1 Place display face down a soft non abrasive surface NOTE For best access route display cables through columns prior to display installation See Cable Management section for details 4 5 CAUTION Using screws of improper diameter may damage your display Proper screws will easily thread into display mounting holes Select screw diameter by examining hardware A C and F H 6mm or 8mm and comparin
3. Figure 2 LVM3X2U LVM3X3U 1 Lay two cart array columns M down on a flat surface 2 Useeight 5 16 18 x 2 1 2 button head cap screws EE and eight 5 16 washers JJ to connect two cross bars J to columns M See Figure 3 3 Use four 5 16 18 x 1 2 button head cap screws LL to attach two end brackets R to cross bars J See Figure 3 Figure 3 4 Use four 5 16 18 x 1 button head cap screws MM to attach two extender brackets W to the other ends of cross bars J See Figure 3 Installation Instructions LVM Series 5 Place two extender blocks U in position between two extender brackets W Be sure to line up holes on blocks and brackets See Figure 4 i exterior Roles back Figure 4 Figure 5 6 While holding extender blocks in position install four 5 16 7 Use four 5 16 18 x 5 button head cap screws GG Tour 18 x 2 1 2 button head cap screws EE through extender 5 16 washers JJ and four 5 1 6 18 lock ute NN to brackets W extender blocks U and into remaining cart secure left and right legs CC and DD to cross bar J See array column M See Figure 5 Figure 6 IMPORTANT Be sure to use interior holes when 8 Use two 5 16 18 x 4 1 2 button head cap screws Y and connecting to the front of the column and exterior holes two 5 16 washers JJ to secure second right leg DD to when con
4. NOTE Clamp brackets P may be flipped in order to use long slots for installation if necessary See Figure 9 flipped bracket Figure 9 NOTE If installing LVM3X1UP proceed ahead to Step 6 4 Measure one screen height down from center point on installed clamp brackets to determine mounting location of lower clamp brackets See Figure 10 5 Use5 16 18 x 4 1 2 button head cap screw FF two 5 16 washers JJ and 5 16 18 lock nut NN to install clamp brackets for lower displays with center diamond one screen height below center diamond of upper installed brackets See Figure 10 NOTE If some clearance is desired in between displays install lower brackets slightly more than one screen height below upper brackets Installation Instructions LVM Series display SE height ZX Figure 10 6 Use four 5 16 18 x 3 4 button head flange screws HH to secure each attached clamp bracket P to a quick connect base Q See Figure 11 Figure 11 NOTE If rails must be installed over cable management holes on column cables must be routed prior to installing rails onto quick connect bases See Cable Management section for details 7 Install two 5 16 18 x 3 4 button head flange screws HH into the top holes on each quick connect base Q See Figure 12
5. 0 2 0 or U 0 0 0 X 0 12 12 rend R2 2 0 2 f rande block 1 4 20 x 1 2 end 1240 2 bracket T 1 1 1 3 16 hex bit Y 0 0 0 5 16 18 x 4 1 4 V 0 2 2 column add on KK 0 0 0 e LVM Series Installation Instructions Assembly And Installation Cart Assembly LVM2X2U LVM3X1UP LVM2X2UP LVM3X2UP 1 Lay two cart array columns M down on a flat surface 2 Useeight 5 16 18 x2 1 2 button head cap screws EE and eight 5 16 washers JJ to connect cross bar J to columns M See Figure 1 Figure 1 3 Use four 5 16 18 x 1 2 button head cap screws LL to attach two end brackets R or R2 to cross bar J See Figure 1 NOTE Custom end brackets R2 are used for LVM3X1UP LVM3X2UP models only for additional support 4 Usefour 5 16 18 x 5 button head cap screws GG four 5 16 washers JJ not for LVM3X1UP and LVM3X2UP models and four 5 16 18 lock nuts NN to secure right and left legs CC and DD to cross bar J See Figure 2 NOTE To ensure right and left legs CC and DD are assembled on the appropriate side make sure the smooth side of the legs are to the outside when assembling to cross bar J 5 Stand cart up on its wheels 6 Proceed to Install Rails Section 10 CC Pd 7 7 e washers not used with LVM3X1UP LVM3X2 models OF
6. AA 4 if necessary Figure 16 WARNING Exceeding the weight capacity can result in LVM2X2U LVM3X2U serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of 125 125 125 125 125 each display and attached accessories mounted to the LVM mount does not exceed the limit listed below If FCA2X1U 125 125 125 125 125 FCA3X1U or FCA3X1UP accessories are added to either the LVM3X3U LVM2X2U the LVM3X2U or the LVM3X1UP the weight limit for each display becomes 100 Ibs 45 4 kg rather than 125 100 100 100 100 100 100 Weight Weight 100 1108 109 Allowed for EACH Capacity of Display Mounting System LVM3X1UP LVM2X2U 125 Ibs 500 Ibs 56 7 kg 226 8 kg 125425125 LVM3X2U 125 Ibs 750 Ibs pu LVM2X2UP LVM3X2UP LVM3X3U 100 Ibs 900 Ibs 45 4 kg 408 2 kg 100100 100100100 LVM3X1UP 125 Ibs 375 Ibs 56 7 kg 170 1 kg 100100 100100100 LVM2X2UP 100 Ibs 400 Ibs 45 4 kg 181 4 kg LVM3X2UP 100 Ibs 600 Ibs 45 4 kg 272 2 kg 15 LVM Series Installation Instructions 6 Starting from the bottom and working up hang interface brackets AA and BB to display rails K or L and KK See Figure 17 WARNING Improper display installation to the c
7. Y 0 2 2 5 16 18 41 4 V 0 0 3 column add on Q 4 6 9 quick connect base P Z 0 6 9 10 24 x 1 1 2 W 0 2 2 extender bracket DD 1 2 2 right leg TT 4 6 6 EI snap cover 3 16 RR 0 0 1 5 32 QQ 0 1 1 1 8 Installation Instructions LVM Series Parts Portrait Models LVM3X1UP LVM2X2UP LVM3X2UP N Quantities are listed as LVM3X1UP LVM2X2UP LVM3X2UP J 1 1 1 base cross bar Hardware bag letters correspond to letters on bag FY Sj 5 1 2 2 portrait display rail M 2 2 2 cart array column L 0 0 0 triple display rail left interface right interface Q 2 4 4 quick connect base d W 0 0 0 7 0 0 0 extender bracket 10 24 x 1 1 2 CC 1 1 1 DD 1 1 1 left leg i AA 3 4 6 BB 3 4 6 TOSS gt add on rail H 16 32 32 EE 8 8 8 FF 2 4 4 GG 4 4 4 5 46 18 au J We 4 5 16 18 x 5 s odaxpip 51518x412 g 2 LL 12 12 12 MM 0 0 0 6 8 8 PP 1 1 1 QQ 0 0 0 RR snap Cover 546 18x1 2 5 16 18 x 1 5 16 18 3 16 a 5 32 2 16 24 E 12 16 24 m 6 24 1 12 16 24 SH 1 4 750x 344x 5 M6x12mm M6x16 lt F 12 1 9 1 9 6 24 v 6 24 S 2 M8x12mm M xtemm Hee 1 4 20 x 1 m e I lt 2 2 2 2 SU SP column cap
8. 54 0 47 d L185 T Se 2350 6 uai SCREEN CENTER 1 31 91 97 WAL HEIGHT H lr 2336 0 24 47 2 53 5 38 621 5 64 1 136 5 SCREEN CENTER d MIN HEIGHT 1 50 38 1 SEH 3 77 2547 95 8 646 8 kd 425 of 1 49 6 97 45 56 108 0 37 9 6 97 176 9 11573 36 00 1763 8 47 I 914 4 215 0 40 40 10262 LVM Series Installation Instructions LVM3X2UP 100 LBS PER DISPLAY D 600 LBS TOTAL CAPACITY 68 00 31 50 800 0 H MAX MOUNTING m PATTERN HEIGHT 3 21 Q 99 3 T 7 31 5 92 69 185 6 7 2354 4 st C ENTER 2 92 12 Ech ig 2339 8 24 47 2 53 5 38 621 5 64 1 136 5 SCREEN CENTER MIN HEIGHT 1 50 38 1 45 88 1 824 1 3 77 25 62 95 8 7 12 KS KE 11573 218 8 Installation Instructions LVM Series LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con l p
9. GHT LVM3X2U LVM3X3U LVM Series i PA TTER M Installation Instructions LVM Series LVM3X1UP 115 LBS PER DISPLAY A A 375 LBS TOTAL CAPACITY 68 00 1727 2 M 31 50 800 0 A E d MAX MOUNTING Z p PATTERN HEIGHT 72 47 3 91 L 1840 7 5 38 99 3 7 SCREEN CENTER P D 136 5 7 31 3 T 73 47 HEIGHT 150 185 4 24 47 38 1 ETC 64 1 621 5 SCREEN CENTER ee MIN HEIGHT 826 DI 377 25 47 95 8 m aT E L Sa 4 4 25 pna 1154 1 108 0 8 47 215 0 LVM2X2UP MAX WEIGHT 100 LBS PER DISPLAY n 8 400 LBS TOTAL CAPACITY GI 46 00 1168 4 31 50 800 0 _ MAX MOUNTING L l PATTERN HEIGHT 391 i 93 7 31 7 92
10. INSTALLATION INSTRUCTIONS Video Wall Carts LVM Series CHIEF Your Vision Our Mounts LVM Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory war
11. art can result in serious personal injury or damage to equipment Install displays from the bottom to the top to decrease the risk of tipping the mount during installation Do not mount all of the displays on one side prior to installing the displays evenly in each row the LVM3X3 mount the center displays in each row prior to installing the outside displays See Figure 17 for an ideal mounting order for the LVM3X3 See Figure 18 for unacceptable and risky installation mounting orders 8 9 5 4 6 zxm SCH Figure 17 Figure 18 7 Use 1 4 20 x 1 1 4 socket head cap screws 1 to secure interface brackets AA and BB to rails for each display Screws must engage through both holes to be fully secured See Figure 19 NOTE Display positions may need to be adjusted after height and or plumb adjustments in order to maintain desired alignment 16 Figure 19 Column Cap Installation NOTE If the top holes on columns will be used for cable management do NOT install column caps to columns as illustrated below See Cable Management section for details 1 Use four 5 16 18 x 1 2 button head cap screws LL to install each column cap N to each column See Figure 20
12. cable from uninstalled displays not shown for clarity display Figure 24 Figure 22 17 LVM Series Installation Instructions 5 For any cable management holes that are not used snap covers TT may be used to cover holes as desired See Figure 25 e655 0 SS 9 EH OTTO Z 1 18 Figure 25 Installation Instructions LVM Series 19 LVM Series Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8800 002369 Rev00 2013 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 03 13 USA International Europe Asia Pacific p TI U gt TI 0 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 SCH n
13. g with mounting holes on display See Figure 15 Select spacers f mounting holes are not recessed and interface brackets AA and BB can lay flat against display then no spacers are required f mounting holes are recessed or if protrusions prevent brackets AA and BB from laying flat then spacers E must be used CAUTION Using screws of improper length may damage your display Proper screws will have adequate thread engagement without contacting bottom of display mounting holes Select screw length See Figure 15 Using your hand insert SHORTEST length screw of selected diameter A or F through 1 4 washer D bracket AA or BB selected spacer E if required into display mounting hole Do NOT thread screw into hole at this time Proper screw length requires base of screw head to protrude above flat washer a distance equal to or greater than the screw diameter If screw length is inadequate select longer screw Select shortest screw which will protrude the required distance Use selected screws A C or F H washers D and spacers E if necessary to connect interface brackets AA and BB to back of display Make sure diamond on interface brackets is even with center of display See Figure 15 non portrait models A C F H x 4 e E x 4 if necessary Figure 15 14 Installation Instructions LVM Series portrait models o A A C or F H x 4
14. iz Stiftmarkierung Marcar com l pis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option d y V 2 Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale 9 Security Wrench Lla
15. necting to back of column See Inset on Figure extender blocks U See Figure 6 5 9 Stand cart up on its wheels No CC JJ x 4 NN x 4 E N Qe lt A Q Figure 6 11 LVM Series Installation Instructions Column Add On Installation LVM3X3U LVM2X2UP LVM3X2UP only 1 Insert one column add on V to each column M making sure holes are lined up on each side See Figure 7 2 Use 5 32 hex key RR and six 1 4 20 x 1 2 flat head cap screws X to secure each column add on V to each column M See Figure 7 rear view A 4 Figure 7 Rails Installation 1 Using display dimensions determine where the center of the top displays will be on the cart IMPORTANT Install all column add ons V if applicable prior to installing rails to columns 2 Place clamp brackets P on columns in the position of where the center of the top displays will be on the cart with the diamond on the brackets being placed at the exact center location See Figure 8 12 rear view center of top displays i 59 Figure 8 3 Use 5 16 18 x 4 1 2 button head cap screw FF two 5 16 washers JJ and 5 16 18 lock nut NN to secure each clamp bracket P to column See Figure 8
16. ranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Do NOT stack multiple accessories on the same display cart Do NOT connect accessories to carts that are already three display high Display carts may NOT be stacked higher than three displays high Portrait versions may NOT be stacked higher than two displays high WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of each display and attached accessories mounted to the LVM mount does not exceed the limit listed below If FCA2X1U FCA3X1U or FCA3X1UP accessories are added to either the LVM2XAU the LVM3X2U or the LVM3X1UP
17. result in the cart collapsing or overturning onto a person causing serious injury or death NOTE NOTE The LVM Series carts have no user serviceable parts The UL listed LVM Series video walls may be used with the UL Listed horizontal extension bracket accessories 20 FCAX14 FCAX08 not included LVM3X2U be used with UL listed add on row FCA3X1U LVM2X2U be used with UL listed add on row FCA2X1U LVM3X1UP may be used with UL listed add on row FCA3X1UP Refer to UL listed accessories manual for mounting instructions DIMENSIONS NOTE NOTE The LVM Series video walls can support screen sizes of 42 46 When FCAX08 FCAx14 or FCAx20 are used the LVM Series video walls can support a screen up to 60 The UL listed leveling feet accessory FCA776 may be used with LVM2X2U LVM3X2U LVM3X3U LVM2X2UP AND LVM3X2UP Refer to FCA776 manual for installation instructions SAVE THESE INSTRUCTIONS LVM SCREEN MN 2X2U 11 15 15 PATTERN CENTER 32 45 HEIGHT 125 186 P Lua ER DISPLAY Uni Installation Instructions ER DISPLAY ENTER HIN HEI
18. the weight limit for each display becomes 100 lbs 45 4 kg rather than 125 Ibs 56 7 kg Max Weight Allowed for EACH Display Max Weight Capacity of Mounting System LVM2X2U 125 Ibs 500 Ibs 56 7 kg 226 8 kg LVM3X2U 125 Ibs 750 Ibs 56 7 kg 340 2 kg LVM3X3U 100 Ibs 900 Ibs 45 4 kg 408 2 kg 125 lbs 375 lbs 56 7 kg 170 1 kg IRA 100105 400 Ibs 45 4 kg 181 4 kg IA RY GTI 100 lbs 600 Ibs 45 4 kg 272 2 kg LVM2X2U LVM3X2U 125 125 125 125 125 125 125 125 125 125 LVM3X3U 100 100 100 100 100 100 100 100 100 LVM3X1UP 125125125 LVM2X2UP LVM3X2UP 100100 100100100 100100 100100100 Installation Instructions LVM Series WARNING Do not use this product outdoors WARNING RISK OF SERIOUS INJURY OR DEATH Placing a remote control or toy on the cart may encourage a child to climb onto the cart causing the cart to tip over onto the child DO NOT place remote controls or toys on the cart WARNING RISK OF SERIOUS INJURY OR DEATH Relocating audio and or video equipment to the cart may result in the cart collapsing or overturning onto a child DO NOT relocate audio and or video equipment to the cart WARNING RISK OF SERIOUS INJURY OR DEATH Use with televisions weighing more than the maximum weight indicated may
19. ve de seguridad Sicherheitsschl ssel Chave de seguran a Chiave di sicurezza Veiligheidssleutel Cl de s curit LVM Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION J lt 1 2 12 7 3 16 included with all 1 8 included with 3x2 3x3 5 32 included with 3x3 PARTS Non portrait Models LVM2X2U LVM3X2U LVM3X3U Portrait Models on next page a gt gs Quantities are listed as LVM2X2 LVM3X2 LVM3X3 J 1 2 2 base cross bar K 2 0 0 dual display rail M 2 3 3 cart array column L 0 2 3 triple display rail 4 6 9 4 left interface ee right interface 5 16 18 x 2 1 2 LL 12 16 16 5 16 18 x 1 2 MM 0 4 4 5 16 18 x 1 CC 1 1 1 left leg KK 0 2 3 Pd Q add on rail HH 32 48 72 FF 4 69 GG 4 4 4 x 3 4 YY 24 30 36 Ar earen BB xe 5 16 NN 8 10 13 5 16 18 Hardware bag letters correspond to letters on bag Y e SEN 16 24 36 16 24 36 99 E 6mm C 16 24 36 14 750x 344x 5 pee I 2 16 24 36 16 24 36 I 8 12 18 M8x12mm 4 E 1 4 20 x 1 bi gt Q N 2 3 3 SS column cap R 2 2 2 U 0 2 2 X 0 0 18 end bracket extender block 1 4 20 x 1 2 T 14 1 P 4 6 9 3 16 hex bit clamp bracket
Download Pdf Manuals
Related Search