Gamber-Johnson 7160-0418 mounting kit
Contents
1. CAMBER JOHNSON Very Well Connected INSTALLATION INSTRUCTIONS Product Revision Form 7160 0418 YALE ROLL FORMED PILLAR ASSY Rev A INST 567 Printing Spec PS 001 The following instruction sheet is for the mounting the Yale roll formed pillar bracket assembly to a pillar of a fork truck Mounting the assembly to the pillar See figure 1 The bracket assembly is designed to attach to the roll formed pillar on the fork truck The mounts are held in place with 3 8 dia hex bolts and carriage bolts 1 Attach the clam shell or extension tube assembly sold separately to adapter bracket 1 with the 5 16 flat washers lock washers and hex nuts 2 Clamp the adapter plates to the roll formed pillar with the 3 8 hardware provided in the hardware bag The 6 carrage bolts are for larger roll formed pillars They will probably need to be cut down depending on customer preference Figure 1 3 8 flat washers Roll Formed Pillar lock washers amp hex nuts Adapter Plate Adapter Plate 2 3 8 carrage bolts 3 8 lock washers amp 50 1 4 hex bolts 5 16 flat washers lock washers amp hex nuts Product Mounting Disclaimer Gamber Johnson is not liable under any theory of contract or tort aw for any loss damage personal inury special incidental or consequential damages for personal injury or other damage of any nature arising directly or indirectly asa result of the improper installation or use of its2. products in vehicle or any other application In order to safely install and use Gamber Johnson products full consideration of vehicle occupants vehicle systems i e the location of fuel lines brakes lines electrical drive train or other systems air bags and other safety equipment is required Gamber Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications and recommendations Gamber Johnson product instruction sheets or workmanship standards as endorsed through the Gamber Johnson Certified Installer Program copyright 2011 Gamber Johnson LLC If you need assistance or have questions call Gamber Johnson at 1 800 456 6868 Figure Example of Dual Clam Shell Assembly attached to Yale Roll Formed Pillar Bracket Assembly 160 0418 Yale Roll Formed Pillar Bracket Assy 160 0366 Fork Lift Dual Clam Shell W Small Plate Position so this surface is relatively level Position the 3 8 bolts as close to the pillar as possible to prevent bowing the components Note The 3 8 pivot bolt Note 1 4 bolts and flat washers have been provided can be tightened to lock in the hardware bag and can be installed in the open the mount In place location opposite the lever handles to lock the clam shells in place Figure 2 Example of Extension Tube Clam Shell with 0 90 Clevis and 3 Arm 160 0418 Yale Roll Formed Pilla
3. r Bracket Assy 7160 0363 Extension tube 7160 03604 Fork lift 0 90 Clevis W Small Plate CFI9 Docking Station Note The 3 8 pivot bolt can be tightened to lock the mount in place Position so this surface Note I 4 bolts and flat washers have been provided is relatively level in the hardware bag and can be Installed in the open location opposite the lever handles to lock the clam shells in place The components to build a pillar mount can also be purchased separetly if required The hardware to assemble the Secondary Clam Shell or 0 90 Clevis to the lower portion are provided with each assembly 7160 0371 or 7160 0356 3 8 hex bolt Secondary Clam Shell 160 037 bearing backup plate g 3 8 flat washer k nylon bearing nylon bearing Lower Clam Shell Mount flo0 035 OF nylon bearing 7160 0370 bearing backup plate a 3 8 flat washer a 3 8 nylok hex nut 3 8 hex bolt im 3 8 flat washer bearing backup plate nylon bearing a 3 8 hex bolt 3 8 flat washer i nylon bearing 3 8 flat washer lt a 3 8 nulok hex nut 0 90 Clevis 160 0356 Lower Clam Shell Mount o0 ona OF 1160 0370 nylon bearing bearing backup plate 3 3 8 flat washer Sa 3 8 nylok hex nut
Download Pdf Manuals
Related Search