Moxa NPORT 5610-8-DTL serial server
Contents
1. Hardware Introduction MOXA Top and Rear Views NPort 5600 8 DTL Reset button Quick Installation Guide First Edition March 2011 Link green Steady Network is connected no data is being transmitted Blinking Network is connected data is being transmitted Ethernet cable is disconnected or has a short off software side software reen Tx Serial device is transmitting data orange Rx Serial device is receiving data Overview The NPort 5600 8 DTL series includes the following models e NPort 5610 8 DTL 8 ports RS 232 0 to 60 C e NPort 5650 8 DTL 8 ports RS 232 422 485 0 to 60 C e NPort 5650I 8 DTL 8 ports RS 232 422 485 0 to 60 C 2KV optical isolation e NPort 5610 8 DTL T 8 ports RS 232 40 to 75 C e NPort 5650 8 DTL T 8 ports RS 232 422 485 40 to 75 C e NPort 5650I 8 DTL T 8 ports RS 232 422 485 2KV optical isolation 40 to 75 C Package Checklist The NPort 5600 8 DTL package should contain the following items e NPort 5600 8 DTL device server e Wall mounting and DIN Rail kits e Stick on pads e Documentation and software CD e Quick installation guide printed e Warranty card Optional Accessories e DK 35A DIN Rail mounting kit 35 mm Note Please notify your sales representative if any of the above items are missing or damaged Optional Accessories can be ordered separately P N 1802056000010 LED indicators Front View Port2 Port 4 Port Ports2. i OCO ian 5 Port 7 Port 1 Port 3 Port DB9 M serial ports RJ45 10 100 Mbps Ethernet port Power input Reset Button Use a pointed object to hold the reset button down for at least five seconds to load the factory defaults Release the reset button when the Ready LED stops blinking LED Indicators The LED indicators on the top panel are used to display the status as follows Power is Off Steady NPort is operational Blinking NPort is responding to NPort Administrator Locate function or NPort is resetting to factory default off Power is off or fault condition exists red IP conflict or DHCP or BOOTP server did not respond properly ff i No fault condition detected O No data is flowing to or from the serial port Hardware Installation STEP 1 After removing the NPort 5600 8 DTL from the box place it on a desktop or other horizontal surface Connect the 12 48 VDC power adaptor to the NPort 5600 8 DTL s power input when using an AC power source or connect the NPort 5600 8 DTL s terminal block directly to a DC power source STEP 2 Use an Ethernet cable to connect the NPort 5600 8 DTL to a network hub or switch You can also connect directly to your computer s Ethernet port which is convenient for initial configuration or testing STEP 3 Connect the NPort 5600 8 DTL s serial port to a serial device Wall or Cabinet Mounting The NPort 5600 8 DTL comes with two metal attachment p
3. 232 TxD RxD RTS CTS DTR DSR DCD GND RS 422 Tx Tx Rx Rx GND RS 485 2 wire Data Data GND RS 485 4 wire Tx Tx Rx Rx GND Serial Line Protection 15 KV ESD for all signals RS 485 Data Direction ADDC Automatic Data Direction Control Serial Communication Parameters Parity None Even Odd Space Mark Data Bits 5 6 7 8 Stop Bit s 1 1 5 2 Flow Control RTS CTS DSR DTR for RS 232 only XON XOFF Transmission Speed 50 bps to 921 6 Kbps Power Requirements Power Input 12 to 48 VDC Physical Characteristics Operating Temperature Standard Models O to 60 C 32 to 140 F Wide Temp Models 40 to 75 C 40 to 167 F Storage Temperature 40 to 85 C 40 to 185 F Operating Humidity 5 to 95 RH Material SECC sheet metal 0 8 mm Dimensions Without ears 197 x 44 x 125 mm With ears 229 x 46 x 125 mm With DIN Rail kit 197 x 52 8 x 125 mm Certifications Regulatory Approvals FCC Class A CE Class A UL 60950 1 LVD Warranty 5 years KA OXA www moxa com support The Americas 1 714 528 6777 toll free 1 888 669 2872 Europe 49 89 3 70 03 99 0 Asia Pacific 886 2 8919 1230 China 86 21 5258 9955 toll free 800 820 5036 2011 Moxa Inc All Rights Reserved 6
4. lates to allow installation on a wall or the inside of a cabinet First attach the brackets to the back of the NPort with screws Next mount the unit on a wall or cabinet with screws Screws should be less than 6 0 mm in head diameter and less than 3 5 mm in shaft diameter DIN Rail Mounting DIN Rail attachments can be purchased separately to attach the product to a DIN Rail The DIN Rail attachments should be oriented with the metal springs on top Standard Attachment DK 35A Attachment 88868808 OO000000 o0000000 Software Installation Information To install NPort Administration Suite insert the NPort Document amp Software CD into your PC s CD ROM drive Locate and run the setup program and follow the on screen instructions The setup program will be named Npadm_Setup_ Version _Build_ DateTime exe e g Npadm _Setup_Ver1 16_Build_11021010 exe Refer to the NPort 5600 8 DTL User s Manual for more details Pin Assignments DB9 Male Ports RS 422 RS 485 2W RS 485 4W 1 DCD__ TxD A a 2 RxD TxD B ee TEE GND C OR E E 2 Wee ete Ca ea E a a Note The NPort 5610 8 DTL supports RS 232 only Specifications LAN Ethernet Ports 10 100 Mbps RJ45 Protection Built in 1 5 KV magnetic isolation Serial Interface RS 232 NPort 5610 8 DTL RS 232 422 485 NPort 5650 8 DTL 5650I 8 DTL Serial Ports 8 DB9 M connectors Isolation 2 KV isolation NPort 5650I 8 DTL Serial Signals RS
Download Pdf Manuals
Related Search