Chief KSA1024B flat panel wall mount
Contents
1. KSA 1024 SHOWN INSTALLED ONTO K SERIES CENTRIS INTERFACE KSA 1024 K SERIES CENTRIS INTERFACE LOCKED SOLD SEPERATELY POSITION Ki Installation Instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to this accessory does not exceed 40 lbs 18 14 kg DO NOT exceed the weight limitations of the mount being installed to the bracket or of the office furniture being used to mount the accessory KSA 1024 SHOWN INSTALLED ONTO K SERIES CENTRIS INTERFACE THUMB NUT QUICK LOCK FLAG SEC URITY SC REW PORT UNLOCKED POSITION Inst2. INSTALLATION INSTRUCTIONS VE SSS W J d d i I HEE Hi d IN ly NAAM A A DE NRA Quick Connect Disconnect Bracket CHIEF KSA 1024 Our Mounts Your Vision KSA 1024 DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief and Centris are registered trademarks of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions DIMENSIONS
3. Exceeding the weight capacity can result in bracket holes and into holes on back of display See Figure serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to this accessory does not exceed 40 lbs 18 14 kg DO NOT exceed the weight limitations of the mount being installed to the bracket or of the office furniture being used to mount the accessory WNW Figure 1 3 For recessed mounting holes install either four M4 x 20mm or four M4 x 30mm Phillips flathead machine screws E or F through corresponding bracket holes and four spacers G or H and into holes on back of display See Figure 2 Zoll flag in open position IMINO Yj Yip Centris head Figure 3 3 Move bracket flag to closed position See Figure 4 TIT mmm 100000001 O mmm mmm Figure 2 Figure 4 KSA 1024 4 Tighten thumbnut on bracket flag to secure bracket to Centris plate See Figure 5 Figure 5 Optional Security Screw Installation 1 Use enclosed 5 32 security hex key C to install M4 x 8mm button head security screw B into security hole on bracket See Figure 6 Figure 6 Installat
4. allation Instructions KSA 1024 LEGEND Tighten Fastener Pencil Mark Befestigungsteil festziehen Stiftmarkierung L Marcar com l pis Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener DIE a 0e Phillips Screwdriver Adjust Open Ended Wrench Remove G ms O By Hand Optional I Hex Head Wrench Security Wrench Zeskantsleutel Veiligheidssleutel Cl a t te hexagonale Cl de s curit KSA 1024 Installation Instructions TOOLS REQUIRED FOR INSTALLATION AND PARTS 5 32 H included security 4 amp LI 1E SCH 5 32 NOT included A 1 LAN security Ouick Connect Disconnect Bracket Assembly kit D 4 E 4 F 4 G 4 H 4 M4 x 12mm M4 x 20mm M4 x 30mm 1 2 x 194 x 1 2 1 2 x 194 x 3 4 Installation Instructions KSA 1024 Assembly And Installation Attach Bracket to Centris Plate 1 Make sure quick connect disconnect bracket flag is in the Attach Quick Connect Disconnect Bracket to open position See Figure 3 Display l 2 Place quick connect disconnect bracket over Centris plate 1 Lay display face side down on a level non abrasive making sure upper lip of bracket covers top of Centris plate surface Lay down a cloth if necessary to avoid scratching See Figure 3 the screen 2 For non recessed mounting holes install four M4 x 12mm Phillips flathead machine screws D through corresponding WARNING
5. ion Instructions Installation Instructions KSA 1024 KSA 1024 CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8800 002008 REV 00 2009 Milestone AV Technologies a Duchossios Group Company www chiefmfg com 03 09 Installation Instructions USA International A 8401 Eagle Creek Parkway Savage MN 55378 P 800 582 6480 952 894 6280 F 877 894 6918 952 894 6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN The Netherlands P 31 0 40 2668620 F 31 0 40 2668615 A Room 24F Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA ARI Th ne 5 RN BE tab RA E DPR 24F P 86 755 8996 9226 F 86 755 8996 9217 PA v gt D SA d Asia Pacific
Download Pdf Manuals
Related Search