Bissell PowerForce
Contents
1. Bissell PowerForce 6594 SERIES 3 KRM 4 Koman 5 6 Assembly Instructions 6 8 KEELES EONS 8 11 MEGEL 15 AUREA EN 16 BEUEUS DJ68 00281A gt Thanks For Buying A BISSELL PowerForce Bagless We re glad you purchased a BISSELL PowerForce Bagless Vacuum Everything we know about floor care went into the design and construction of this complete high tech home vacuuming system Your BISSELL PowerForce Bagless is well made and we back it with a limited comprehensive one year warranty We also stand behind it with a knowledgeable dedicated Consumer Services Department so should you ever have a problem you ll receive fast considerate assistance My great grandfather invented the floor sweeper in 1876 Today BISSELL is a global leader in the design manufacture and service of high quality homecare products like your BISSELL PowerForce Bagless Thanks again from all of us at BISSELL AM ord f Kd Mark J Bissell President and Chief Executive Officer IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should be observed including the following READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM Always connect to a polarized outlet left slot is wider than right Unplug from outlet when not in use and before conducting maintenance AWARNING To reduce the risk of fire electric shock or injury M Do not modify the pola2. You should also clean the brush and brush ends of strings hair and carpet fibers These can wrap around the brush and hamper its ability to effectively clean your carpet Also remove any debris that has accumulated under the brush cover Unplug cleaner from electrical outlet p EN Place handle in Low position and turn vacuum cleaner over so bottom side is up i Lift tab 1 and release the three latches in order 2 4 as A 48 p W marked Lift the Brush Cover off S 4 Grasp Rotating Floor Brush at both ends and lift Q Clean strings hair and other debris from Rotating Floor Brush paying particular attention to brush ends 6 Clean strings hair and other debris from Motor Pulley and Drive Belt areas Motor Pulley 9 Check Drive Belt carefully for wear cuts or stressed areas 8 Check Air Passageway for obstructions Remove debris from this area Replace Drive Belt Use only BISSELL Style 10 Replacement Belts 32074 in your BISSELL PowerForce Bagless Unplug cleaner from electrical outlet i gin Rotating Floor Brush removed from vacuum cleaner Steps 1 4 of Check Rotating Floor Brush and Drive Belt grasp old Drive Belt and remove from Motor Pulley Discard old Drive Belt cy r Place new Drive Belt over Motor Pulley and stretch other Wi w O end over Rotating Floor Brush in the space between WP ee the bristles gt 7 o
3. dirt Possible Cause Crack or hole in Hose Clog in vacuum ZAAWARNING To reduce the risk of injury from moving parts and or electrical shock turn Power Switch OFF and disconnect polarized plug from electrical outlet before performing troubleshooting checks Remedies Check electrical plug Check Replace fuse or reset breaker Remedies Adjust Powerfoot to correct height setting Grasp Quick Reach Handle and firmly push Hose Wand onto the suction opening Make sure Twist n Snap Hose is snapped into locked position Check Hose and replace if needed Replace Drive Belt see pg 10 Replace brush Remove brush and clean debris from brush ends Clear clog see pg 11 Empty Dirt Container Position correctly and lock in place Check and clean Inner and Outer Circular Filters Pre Motor and Post Motor Filters Check for a clog in the tube in the center of the Dirt Container clear and properly install Louvers Remedies Check Hose and replace if needed Clear clog see pg 11 Troubleshooting Continued Tools won t pick up dirt continued Possible Cause Remedies Dirt Container full Empty Dirt Container Dirt Container or Upper Tank Position correctly and not installed properly lock in place Filters are dirty Check and clean Inner and Outer Circular Filters Pre Motor and Post Motor Filters Louver missing or installed incorrectly Check fo
4. D WITH THE USE OF THIS PRODUCT BISSELL S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER Bissell ORAL OR WRITTEN ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION ee OF LAW INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE ONE YEAR DURATION 2004 BISSELL Homecare Inc FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE Grand Rapids Michigan R TERT A A All rights reserved Printed in Korea Some states do not allow limitations on how long an implied warranty lasts Part Number 603 2558 so the above limitation may not apply to you Rev 10 05 Visit our website at www bissell com
5. Place ends of Rotating Floor Brush down into slots on sides as shown g n Rotating Floor Brush by hand several times in the direction of Motor Pulley If properly installed Drive Belt will center itself on Rotating Brush o Reposition Brush Cover and snap back into place Check to be sure all three latches are secured Replace Lightbulb Use only BISSELL Replacement Bulbs in your BISSELL PowerForce Bagless Unplug cleaner from electrical outlet Using a flat screwdriver table knife or coin insert into the slot on the right of the lens and gently push inner latch to the left as shown to remove the lens Standard Bulb remove the bulb from the socket by grasping bulb and pulling straight out Install the new bulb by pushing it gently into the socket until the bulb snaps into place Large Bulb remove the bulb from the socket by pushing bulb in gently and turning it towards brush Install the new bulb by pushing it gently into the socket and turning away from the brush O Reposition lens by inserting tab on left side and then pushing the right side back into place Clearing Clogs Low suction poor pickup or no suction may be due to a clog in the vacuum cleaner If you notice a change in the sound of the motor or a reduction in the spinning action in the Dirt Container check for clogs Unplug cleaner from electrical outlet 12 Empty Dirt Container Gheck Upper Tank and Louvers for build up or clogs Ch
6. e kerosene etc or use in the presence of explosive liquids or vapors Do not pick up toxic material chlorine bleach ammonia drain cleaner etc Do not use vacuum cleaner in an enclosed space filled with vapors given off by oil base paint paint thinner some moth proofing substances flammable dust or other explosive or toxic vapors Do not pick up hard or sharp objects such as glass nails screws coins etc Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use without filters in place Use only on dry indoor surfaces Keep appliance on a level surface Do not carry the vacuum cleaner while it is running SAVE THESE INSTRUCTIONS FOR FUTURE USE THIS APPLIANCE HAS A POLARIZED PLUG To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install a proper outlet Do not change the plug in any Way This model is for household use only Handle Stretch Hose Handle uick Release ord Wrap OO Extension Wand Quick Reach Handle Hose Wand Dusting Brush Upholstery Tool Upper Tank Power Switch Handle Release Pedal Inner and Outer Circular Filters Filter Cup Foot Hose L
7. eck to make sure Louvers are installed correctly To unlock the Louvers grasp the rim and turn toward the left Pull straight down to remove If the Louvers are missing or not locked into place check and clear the tube in the center of the Dirt Container rerove the Twist n Snap Hose from the vacuum by turning to the left Check the Suction Inlet Hose and Hose Wand for clogs Remove any clogs from the hose using a long narrow object e Check the Foot Hose for clogs If needed remove the screw attaching the Hose Wand Base to the vacuum Straighten the Foot Hose and unclog with a long narrow object G the clog persists follow the instructions for Checking the Rotating Floor Brush on page 10 and inspect the Air Passageway for obstructions Standard Bulb _ Large Bulb Wand Base Air Passageway Troubleshooting Vacuum cleaner won t run Possible Causes Power cord not plugged in Blown fuse tripped breaker Vacuum cleaner won t pick up dirt Possible Causes Incorrect Height Adjustment Hose not attached to suction opening Twist n Snap Hose not securely attached Crack or hole in Hose Broken or worn Drive Belt Rotating Floor Brush bristles worn Rotating Floor Brush jammed Clog in vacuum Dirt Container full Dirt Container not installed properly Filters are dirty Louvers missing or installed incorrectly Tools won t pick up
8. er Attach Vacuum Hose and Tools Attach the Twist n Snap Hose by lining up the tabs on the base with the corresponding notches on the back of the vacuum as shown 2 Turn the Twist n Snap Hose to the right to lock the hose into place Grasping the Quick Reach Handle slide the end of the Hose Wand onto the Hose Wand Base Snap the Hose into the Hose Clip NOTE The Powerfoot will not operate effectively unless the Hose Wand is firmly attached Attach Vacuum Hose and Tools Continued O Slide the Extension Wand and the Crevice Tool together into the storage clip on the side of the vacuum 9 Snap the Combination Tool into the storage clip on the back of the vacuum How To Use Your Vacuum Handle Positions Press the Handle Release Pedal with your foot to place your vacuum in one of three cleaning positions rio For storage and above floor cleaning with tools Normal Cleaning Press Handle Release Pedal once Use for most household floor cleaning tasks gg Cleaning With the vacuum in normal cleaning posi tion press Handle Release Pedal again Use for reaching under low furniture such as tables chairs or beds Height Adjustment Before using your vacuum N make sure that the Dirt The Powerfoot Rotating Floor Brush can be Container is in locked posi adjusted to clean several floor surfaces tion and that all filters Inner 3 g Circular Outer Circular NOTE For optimal cleaning perf
9. ition m The Floor Brush will continue to rotate i while you use your vacuum for above 0 Grasp the Quick Reach Handle and lift floor cleaning To prevent carpet Hose Wand to separate from suction damage do not lean on the vacuum intake opening or let the Powerfoot tilt forward Attach tools by firmly pushing onto Vacuum Hose or Extension Wand Combination Dusting Brush Upholstery Tool Two types of cleaning tools are included in one attachment rotate for desired tool E Use Brush side to dust furniture blinds books lamps shelves and baseboards E Use Upholstery side for curtains draperies cushions fabrics Crevice Tool Use in tight narrow spaces Extension Wand Use with desired attachment for a longer reach M A CAUTION The Rotating Floor Brush continues to rotate while tools are in use To reduce the risk of injury from moving parts always move the cleaner with the Carrying Handle at the back of the cleaner Always place vacuum cleaner on floor with Handle in Upright position when using tools Never place your fingers under the cleaner when it is running Never place Powerfoot on furniture or uneven surfaces Do not place vacuum cleaner close enough to objects to pull them into rotating brush Hair string and small objecis can block the Vacuum Hose or Tools Check them occasionally for obstructions Power Cord Storage When you are done using your vacuum retum it to
10. k and turn the rim of the Louvers to unlock Pull straight down to remove Cleaning the Pre Motor Filter with damp or wet filters or without all Unplug the cleaner from electrical outlet filters in place Pre Motor Filter protects the motor from debris It is located underneath the Dirt Container and Filter Cup in the center of the round part of the Lock n Seal Lever Remove the small round Filter and any debris on top of it Rinse well under warm water then air dry thoroughly before replacing Cleaning the Post Motor Filter Use only BISSELL Style 10 Replacement Filters in your BISSELL PowerForce Bagless Unplug the cleaner from electrical outlet Post Motor Filter ire Post Motor Filter assists in the filtration process to return clean air to the room It is located behind the door on the front of the cleaner When the filter becomes dirty open the door remove the filter and clean To reduce the risk of m Post Motor Filter may be hand washed in warm water Mild injury from moving parts detergent may be used if desired Rinse well then air dry thoroughly turn off vacuum cleaner before replacing and disconnect Power Plug from electrical outlet Replace the door by inserting the tabs on the left side and snapping the right side into place Check Rotating Floor Brush and Drive Belt You should check your vacuum cleaner s Rotating Floor Brush and Drive Belt regularly for wear or damage
11. ner Unplug cleaner from electrical outlet Position Side the Lock n Seal Lever to the Unlock position Grasp handle and pull the Dirt Container straight out to remove from vacuum 14 Empiy dirt into garbage container Put the Dirt Container back in the vacuum and slide the lever to the Lock position Note The Dirt Container may be washed in warm water with a mild detergent Remove the Filter Cup from the bottom before washing Reassemble and make sure it is completely dry before using again Cleaning The Inner amp Outer Circular Filters Use only BISSELL Style 10 Replacement Filters in your BISSELL PowerForce Bagless D Unplug the cleaner from electrical outlet Remove the Dirt Container as described in the previous section Grasp the Filter Cup located at the bottom of the Dirt Container and twist counterclockwise to unlock and remove 3 Grasp the Circular Filters and twist to unlock Pull straight up to remove 6 Separate the Outer foam and Inner pleated Circular Filters Wash each individually by hand in warm water Mild detergent may be used if desired Rinse well then air dry thoroughly before putting them back together and replacing in Filter Cup 8 The Filter Cup may be washed in warm water with a mild detergent Make sure it is completely dry before reassembling with filters Gr Upper Tank and Louvers may also be wiped clean with a damp cloth Reach underneath the Upper Tan
12. ock n Seal Lever Post Motor Height Filter Adjustment Knob Powerfoot Furniture Protection Guard Do not plug in your vacuum cleaner until you are familiar with all instructions and 4 operating procedures How To Use This Guide This User s Guide has been designed to help you get the most satisfaction from your B SSELL PowerForce Bagless You ll find assembly and operating instructions safety precautions as well as maintenance and troubleshooting instructions Please read this Guide thoroughly before assembling your vacuum Cleaner dangerous To avoid Pay particular attention to the product diagram danger of suffoca assembly instructions and part names Locate and tion keep away from organize all parts before assembly Familiarize babies and children yourself with the parts and where they fit Following this User s Guide will greatly enhance your ability to get the most performance from your BISSELL PowerForce Bagless for many years A WARNING Plastic film can be How To Put It Together The only tool you ll need to assemble your vacuum Cleaner is a screwdriver Attach Handle To Vacuum Locate the vacuum Handle and remove the screw packet taped to the base of the Handle Stand the vacuum upright and place the Handle on the top of the vacuum body as shown 3 Insert the screws provided from the screw packet into the existing holes on each side Tighten securely with a screwdriv
13. ormance Pre Motor and Post Motor are adjust to the lowest practical setting If in place Do not operate your your cleaner is difficult to push adjust to vacuum without these filters the next higher setting grace Handle in Upright Position Q un Height Adjustment Knob to desired setting Lowest Setting For bare floors Medium Settings For short and medium pile carpets Highest Setting For plush pile carpet Before cleaning under low furniture check area first for objects that might harm the unit or block the Vacuum Hose KEZ O a Be he d grace the Handle in the normal cleaning position and the Powerfoot will adjust to the setting chosen NOTE You may also adjust the setting while in the normal cleaning position Your vacuum features a Quick Release Cord Wrap To remove the Power Cord quickly and easily rotate the Upper Cord Wrap towards floor and slip Power Cord from Upper and Lower Cord Wraps Transporting Cleaner 09 move your cleaner from room to room put the Handle in the upright position tilt the cleaner back on its rear wheels and push forward tte Cleaner can also be moved by using the Carrying Handle on the back Special On Board Tools Carrying Handle Your BISSELL PowerForce Bagless is not only a powerful carpet and rug vacuum Cleaner it s also a versatile above floor vacuum cleaner when you select one of the special tools NOTICE Raise Handle to Upright Pos
14. ow Limited One Year Warranty Subject to the EXCEPTIONS AND EXCLUSIONS identified below upon receipt of the product BISSELL Homecare Inc will repair or replace with new or remanufactured components or products at BISSELL s option free of charge from the date of purchase by the original purchaser for one year any defective or malfunctioning part See information below on If your BISSELL product should require service This warranty applies to product used for personal and not commercial or rental service This warranty does not apply to fans or routine maintenance components such as filters belts or brushes Damage or malfunction caused by negligence abuse neglect unauthorized repair or any other use not in accordance with the User s Guide is not covered If your BISSELL product should require service Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area If you need information about repairs or replacement parts or if you have questions about your warranty contact BISSELL Consumer Services Website or E mail www bissell com Use the Customer Services tab Or Call BISSELL Consumer Services 1 800 237 7691 Monday Friday 8 a m 10 p m ET Saturday 9 a m 8 p m ET Or write BISSELL Homecare Inc PO Box 3606 Grand Rapids MI 49501 ATTN Consumer Services BISSELL HOMECARE INC IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATE
15. r a clog in the tube in the center of the Dirt Container clear and properly install Louvers Vacuum cleaner is difficult to push Possible Causes Remedies Incorrect Height Adjustment Adjust Powerfoot to correct height setting Brush Cover installed incorrectly Make sure all three latches are secured Visible dirt escaping from cleaner Possible Causes Remedies Dirt Container full Empty Dirt Container Filters missing or installed incorrectly Check Inner and Outer Circular Filters and Post Motor Filter for correct installation Dirt Container installed incorrectly Pull out and re insert Dirt Container correctly Filter Cup installed incorrectly Remove Dirt Container and make sure Filter Cup is fully attached If suggested solutions do not correct the problem call BISSELL Consumer Services 1 800 237 7691 Monday Friday 8 a m 10 p m ET saturday 9 a m 8 p m ET or visit the BISSELL website www bissell com Replacement Parts BISSELL PowerForce Bagless Series You may purchase replacement parts from your retailer by calling BISSELL Consumer Services or by visiting our website To locate a retailer near you or to place an order using Visa MasterCard Discover or American Express call BISSELL Consumer Services 1 800 237 7691 Monday Friday 8 a m 10 p m ET Saturday 9 a m 8 p m ET Or visit our Website www bissell com Item Part No Part Name 1 32074 S
16. rized plug to fit a non polarized outlet or extension cord Do not leave vacuum cleaner unattended when it is plugged in Unplug from outlet when not in use and before servicing Do not use outdoors or on wet surfaces Do not allow children to operate vacuum Cleaner or use as a toy Close attention is necessary when used by or near children Do not use for any purpose other than described in this User s Guide Use only manufacturer s recommended attachments Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water have it repaired at an authorized service center Do not pull or carry by cord use cord as a handle close a door on cord or pull cord around sharp edges or corners Do not run appliance over cord Keep cord away from heated surfaces Do not unplug by pulling on cord To unplug grasp the plug not the cord Do not handle vacuum cleaner or plug with wet hands Do not put any object into openings Do not use with any opening blocked keep openings free of dust lint hair and anything that may reduce air flow Keep hair loose clothing fingers and all parts of body away from openings and moving parts Turn off all controls before plugging or unplugging vacuum cleaner M Use extra care when cleaning stairs M Unplug before attaching the turbobrush m Do not pick up flammable materials lighter fluid gasolin
17. the Upright position and store the Power Cord NOT CE While vacuuming certain carpets Tern vacuum cleaner off and low humidity conditions may generate small static discharges Unplug Power Cord by grasping the polarized plug NOT The discharges are entirely in any way with the main Loop Power Cord around Cord Wraps on side of Sower SUDON vacuum cleaner cir molded plug to Power Cord to secure How To Maintain Your Vacuum To maintain maximum cleaning performance the following maintenance steps must be performed ZA WARNING To reduce the risk of Empty the Dirt Container when the dirt reaches the electric shock turn Power Full line on the side Switch OFF and discon nect polarized Check the Inner and Outer Circular Filters and the plug from electrical outlet Pre Motor Filter at least once a month and clean or before performing maintenance or epeo evle troubleshooting checks 3 Clean or replace the Post Motor Filter every three to six months Note More frequent filter cleaning or replacing may be necessary if you are Tip vacuuming new carpet fine dust or have For maximum cleaning allergy concerns Follow the instructions on performance check the following pages to perform these simple and clean or replace all maintenance steps filters as suggested Empty Dirt Container The Dirt Container needs to be emptied when the dirt reaches the Full line on the side of the Contai
18. tyle 7 9 10 Drive Belt 2 Pack 2 203 1007 Large Headlight Bulb Select Models Only 3 203 1297 Standard Headlight Bulb Select Models Only 4 203 1063 Crevice Tool 5 203 1099 Combination Dusting Brush Upholstery Too 6 203 1022 Extension Wand it 203 1216 Wire Reinforced Twist n Snap Vacuum Hose 8 203 1195 Wide Brush Roll 9 32064 Style 9 10 Inner amp Outer Circular Filter Set 10 32065 Style 9 10 Inner Circular Filter only til 32066 Style 10 Outer Circular Filter and Post Motor Filter Set 12 203 1215 Pre Motor Filter BISSELL Consumer Services For information about repairs or replacement parts or questions about your warranty call BISSELL Consumer Services 1 800 237 7691 Monday Friday 8 a m 10 p m ET Saturday 9 a m 8 p m ET Or write BISSELL Homecare Inc PO Box 3606 Grand Rapids MI 49501 ATTN Consumer Services Or visit the BISSELL website www bissell com When contacting BISSELL have model number of unit available Please record your Model Number Please record your Purchase Date NOTE Please keep your original sales receipt It is your warranty This warranty gives you specific legal rights and you may also have other rights which may vary from state to state If you need additional instruction regarding this warranty or have questions regarding what it may cover please contact BISSELL Consumer Services by E mail telephone or regular mail as described bel
Download Pdf Manuals
Related Search