Pyle PBKCM4WL sport watch
Contents
1. is calculated with the Trip Timer TM so AVS is the average speed only while riding Press the RIGHT button to enter TM mode COMPUTER Slide the computer onto the mounting bracket until it snaps firmly into position Press the release button to take out the computer as shown in Fig 1 Fig 1 Release ATTENTION Refer to the appendix for installation reference TRIP TIMER TM Trip timer measurement is indicated by TM and is displayed on the bottom line Trip Timer is activated automatically with speedometer input On when you ride and off when you stop It records only the time spent actually riding Reset TM to zero by pressing the LEFT button for 2 seconds in DST mode Press the RIGHT button to enter Temperature mode TEMPERATURE Press and hold LEFT button for 2 seconds G will start to flash Press RIGHT button to select C or F and press LEFT button to confirm Press RIGHT button to enter the Scan mode SCAN The Scan mode allows DST MXS AVS and TM to cycle on the screen without pressing any keys Press the RIGHT button to enter the Clock mode START STOP To start the unit press the RIGHT button to turn on the display and the wireless mounting system To stop the unit left unused for over 5 6 minutes and then the computer will automatically switch off to preserve batteries WHEEL SIZE INPUT Press2. reach 600 1200 1800km or miles Press the LEFT button to stop flashing of spanner sA SPEED COMPARATOR Cadence A or sign appears to the right of the speed indicates you are travelling faster than your average speed AVS A indicates you are riding slower than your average speed A cyclist symbol appears to the left of the speed The wheel turns forward to indicate acceleration The wheel turns backward g g to indicate deceleration MALFUNCTION PROBLEM Inaccurate maximum Unknown atmospheric or RF speed reading interference No speedometer Improper magnet transmitter reading alignment Check battery and correct installation Slow display Temperature outside of operating response limits 0 55 C Black display Temperature too hot or display exposed to direct sunlight too long No trip distance reading alignment Check correct transmitter magnet Check battery and correct installation Display shows irregular figures Take out computer battery and install again CE X Art No BC P3 GB s eee eee eee eee eee eee eee eee eee eee eee eee eee eee eee eee eee eee eee eee eee eee eee eee SPEEDOMETER SPD Instantaneous Speed is indicated on the 7 top line The range of measurement is from 0 to 99 KM hr 0 to 99 M hr and accuracy is 0 5 KM hr M hr CLOCK 12H 24H A 12 or 24 hour digital clock is indicated by the flickering colon
3. FEATURES ATTENTION Computer Functions refer to the packing details 5 7 9 13 16 FUNCTIONS 4 Speedometer SPD 0 99 9 KM hr or M hr Tripmeter DST 0 999 9 KM or M Odometer ODO 0 9999 9 KM or M Auto Trip Timer TM 9 59 59 Maximum Speed MXS 0 99 9 KM hr or M hr Average Speed AVS 0 99 9 KM hr or M hr Scan for DST MXS AVS TM Freeze Frame Memory for TM AVS DST Speed Comparator Or Digital Clock 12 24 hour selectable Speed Tendency 8 e or f e e e eeee ee eg 8 8 8 EE Odometer Save Function Temperature 10 C to 50 C C F Selection Maintenance Program ELBACKLIGHT OPTIONAL VV VV V TRIPMETER DST Trip Information Reset Mode Trip distance measurement is indicated by DST and is displayed on the bottom line Tripmeter is activated automatically with speedometer input Reset DST to zero by pressing the LEFT button for 2 seconds DST Trip distance TM Trip Timer amp AVS Average Speed will also be reset at that time Press the RIGHT button to enter MXS mode MAXIMUM SPEED MXS Maximum speed measurement is indicated by MXS and is displayed on the bottom line Maximum speed is stored in memory and updated only when a higher speed is reached To reset MXS press and hold the RIGHT button to enter AVS mode AVERAGE SPEED AVS Average Speed measurment is indicated by AVS and is displayed on the bottom line AVS
4. and hold LEFT and RIGHT buttons for 2 seconds or after the replacement of battery the unit is switched to wheel size input mode Multiply wheel diameter d Fig 2 in millimeters by 3 1416 to determine wheel factor c Press the LEFT button to select digit to be input and the RIGHT button to adjust the digit to the desired number hold for fast advance Press the LEFT button again to KM MILE selection Note removing battery will erase Wheel Size Input For convenience you can refer to the chart of wheel diameter size factor inputs Wheel Diameter d 20 2a 24 26 26 5 26 6 26 8 27 28 650A Tubular 700x25C 700x28C 700x32C 700B distance in millimeter per one turn lt c w tire ATB 24 x1 75 ATB 26 x1 4 ATB 26 x1 5 ATB 26 x1 75 ATB 26 x2 650B 27 x1 27 x1 1 4 FREEZE FRAME MEMORY Press the LEFT button Freeze Frame Memory can lock the display at the end of a ride segment and information TM DST and AVS which will be flashing can be read at a later time by pressing the RIGHT button To release the memory press the LEFT button until the display digit is static again This is particularly useful when crossing the finish line of a time trial since the TM cannot be stopped manually ODOMETER SAVE FUNCTION The SAVE function allows you to keep the important data of total distance ODO even after replacement of battery To set ODO after battery replacement and wheel size
5. on the bottom line To switch between the 12 and 24 hour format or to adjust time press the LEFT button for 2 seconds 24H will start to flicker Use the RIGHT button to select 12H for12 hour format or 24H for 24 hour format Press the LEFT button to confirm Next the hour digits will start to flicker Use the RIGHT button to select the hour To change minutes press LEFT button again The minutes will start to flicker Use the RIGHT button to select the minutes Press the LEFT button once more to return to CLOCK Mode Press the RIGHT button to enter ODO mode ODOMETER ODO Total distance travelled is indicated by ODO and display on the bottom line To reset ODO press and hold LEFT and RIGHT buttons for 2 seconds or remove the battery Press the RIGHT button to enter DST mode L
6. setting press RIGHT button to ODO mode and then press and hold LEFT button for 2 seconds until the last digit flickering To adjust number press the RIGHT button Press the LEFT button to confirm Repeat above sequence to reach the desired odometer value Press the LEFT button again to return to normal ODO mode EL BACKLIGHT OPTIONAL The EL backlight can be turned on either as follows 1 Holding the RIGHT button for 2 seconds the EL light will be turned on for 8 seconds and the computer will then go to fast scan mode with trip distance maximum speed average speed and trip timer displayed once 2 Press once on the LEFT Button the EL light will be turned on for 4 seconds and the comuter will go to the freeze frame menory mode as well KM MILE SELECTION After the wheel size input the following function is selection of kilometers or miles as the measurement for distance Press the RIGHT button to choose between kilometer KM and Mile M press the LEFT button to confirm MAINTENANCE PROGRAM o It is used to remind you for the parts replacement or to lubricate the chains and wheels after the peset distance is reached Right after KM MILE selection the preset total distance of 600km or miles will flash press the RIGHT button to select between 200 400 600 amp 800km or miles and press LEFT button to confirm For example if 600 km is selected the spanner will flash whenever the total distance ODO
Download Pdf Manuals
Related Search