Philips wireless microphone & Bluetooth® speaker AEA7100
Contents
1. 1 Open the battery compartment and take out the battery cartridge 2 Insert 3 x AAA batteries supplied into the cartridge with correct polarity as indicated EN 7 3 Push back the battery cartridge then close the battery compartment e If you are not going to use the microphone for a long time remove the batteries e New batteries installed in the microphone support up to 30 hours of continuous use When the power indicator flashes red it indicates that the power level is low and you need to replace the batteries 4 Play Sing along through the wireless microphone Note The effective operation range between the wireless microphone and Bluetooth speaker is approximately 10 meters 30 feet 1 Dock your iPad onto the Bluetooth speaker L gt A prompt pops up on the Pad screen asking you to install the relevant app Application Not Installed This accessory requires an application you do not have installed Would you like to install it from the App store O WE Jl 2 Tap YES on the prompt to install the app StarMaker Karaoke Auto Tune from Apple App Store No 3 After successful installation run StarMaker Karaoke Auto Tune on the iPad en A StarMaker 4 Slide the OFF ON switch on the wireless microphone to the ON position then select a song from the app and tap Sing gt RECORD hb The wireless microphone start2. Tune through the wireless microphone With the Bluetooth speaker you can e play music from a Bluetooth enabled device that supports A2DP Advanced Audio Distribution Profile e charge or play music from your iPad directly through the dock connector e play music from other audio devices through the AUDIO IN socket What s in the box Check and identify the contents of your package e Wireless microphone e Bluetooth speaker e AC power cord e 3 X AAA batteries e Quick start guide Overview of the unit Wireless microphone Line out socket e To use the microphone separately connect to the MIC input socket of an existing Hi Fi system Q Battery compartment 3 OFF ON e Switch the microphone on or off 4 Power indicator e Light up red when the wireless microphone is switched on e Flash red when the battery level is low EN 5 Bluetooth speaker oS 2 E Ey O Power indicator e Indicate the power status O e Turm the unit on off Bluetooth indicator e Indicate the Bluetooth status e Adjust volume e Press pair with a Bluetooth enabled device that supports A2DP Advanced Audio Distribution Profile e Press and hold pair with the wireless microphone in case automatic pairing fails Dock for iPad SOFTWARE UPGRADE not for use by end users AUDIO IN e Connect an external audio player through a 3 5mm a
3. moisture and objects filled with liquids such as vases should not be placed on the device CAUTION To prevent electric shock fully insert the plug For regions with polarized plugs To prevent electric shock match wide blade to wide slot Important Safety Instructions Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth WQOOOO D Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat N EN 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet AC Polarized Plug Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 41 Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or
4. the iPad 1 Make sure that the iPad has been loaded correctly 5 Use on the top of the Bluetooth 2 Start music play on your iPad speaker to adjust volume L gt The connected iPad starts to play 3 Use on the top of the Bluetooth speaker to adjust volume EN 11 Charge the iPad The docked Pad begins to charge as soon as the unit is connected to AC power Play from an external device You can also listen to an external audio player through the Bluetooth speaker 1 Connect a 3 5mm audio cable to e the AUDIO IN socket on the back of the Bluetooth speaker e the headphone socket on an external audio player 2 Start music play on the external audio player 3 Use on the top of the Bluetooth speaker to adjust volume 5 Prod U Ct Dimensions VW x H x D info rmation Speaker 300 x 162 x 148mm e Microphone 5205555 52m Weight NIE e Speaker 1 3kg e Product information is subject to change without prior e Microphone 0 3kg notice Specifications Amplifier Rated Output Power 2X SW RMS Signal to Noise Ratio gt 0dB Aux in Link 600 mV RMS 20 kohm Speakers Speaker Impedance 4 ohm Speaker Driver 7Omm full range Sensitivity gt 84dB 1m 1W Bluetooth Bluetooth version V2 1 EDR Frequency band 2 402 2 480 GHzISM Band Range 10m free space General information AC power 120 Ve 60 iz Operation Power 20 WV Consumption Standby Powe
5. this apparatus in a confined space Always leave a space of at least four inches around this apparatus for ventilation Ensure curtains or other objects never cover the ventilation slots on this apparatus Information about the use of batteries en Caution e Risk of leakage Only use the specified type of batteries Do not mix new and used batteries Do not mix different brands of batteries Observe correct polarity Remove batteries from products that are not in use for a longer period of time Store batteries in a dry place e Risk of injury Wear gloves when handling leaking batteries Keep batteries out of reach of children and pets e Risk of explosion Do not short circuit batteries Do not expose batteries to excessive heat Do not throw batteries into the fire Do not damage or disassemble batteries Do not recharge non rechargeable batteries Notice Notice of compliance Modifications The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment FCC amp RSS compliance statement This device complies with Part 15 of the FCC Rules and Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause unde
6. Always there to help you Register your product and get support at www philips com welcome Question Contact Philips AEA7100 on the dance floor dont User manual PHILIPS Contents 1 Important Safety Notice Your Wireless Microphone and Bluetooth Speaker Introduction What s in the box Overview of the unit Get started Connect power Switch on the Bluetooth speaker Install replace microphone batteries Play Sing along through the wireless microphone Play from a Bluetooth enabled device Play and charge your Pad through the dock connector directly Play from an external device Product information Specifications Troubleshooting O1 U1 al al Sl NNN 11 12 13 13 14 EN 1 Important Safety CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ge N This bolt of lightning indicates uninsulated material within the device may cause an electrical shock For the safety of everyone in your household please do not remove the covering CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The exclamation mark calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems WARNING To reduce the risk of fire or electric shock the device should not be exposed to rain or
7. a Bluetooth enabled device E e The effective operation range between the Bluetooth speaker and your Bluetooth enabled device is approximately 10 meters 30 feet To pair with a Bluetooth enabled mobile device make sure that no Pad is docked or you have stopped music play and exited StarMaker Karaoke Auto Tune on your docked Pad To pair with a new mobile device you can press to remove the existing Bluetooth connection To play from a Bluetooth enabled device make sure that you are not playing music from your Pad docked on the Bluetooth speaker 1 2 Press 3 on the top of the Bluetooth speaker L gt The Bluetooth indicator flashes blue quickly 0 m0 xs 7 N Enable Bluetooth on your device that supports A2DP Advanced Audio Distribution Profile 3 Select PHILIPS_AEA7100 on your Bluetooth enabled device if necessary Play and charge your iPad input 0000 as the paring password through the dock connector L gt After successful pairing and connection the Bluetooth indicator on the speaker turns solid blue and the Compatible iPad speaker beeps twice directly This unit supports play and charge of the following iPad models e New iPad e Pad2 e Pad Load the iPad e Dock your iPad Y 4 7 4 Start music play on your Bluetooth enabled device To remove the iPad e Pull the iPad out of the dock Listen to
8. d music play on the connected device Failed to set up connection between the microphone and speaker e Check whether both the wireless microphone and Bluetooth speaker are switched on e Make sure that the wireless microphone and Bluetooth speaker are within the the effective operation range that is approximately 10 meters 30 feet e Press and hold 3 on the top of the Bluetooth speaker for more than 10 seconds to set up wireless connection manually Howling or echo from the wireless microphone e Adjust volume e Increase the distance between the microphone and speaker or adjust the angle of the microphone towards the speaker No response from the Bluetooth speaker e Disconnect and reconnect the AC power plug and then switch on the device again PHILIPS Specifications are subject to change without notice 2012 Koninklijke Philips Electronics N V All rights reserved AEA7100_UM_17_V1 0
9. lized company Please observe the local regulations regarding the disposal of packaging materials exhausted batteries and old equipment Made for iPad Made for Pad means that an electronic accessory has been designed to connect specifically to iPad and has been certified by the developer to meet Apple performance standards Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards Please note that the use of this accessory with IPad may affect wireless performance iPad is a trademark of Apple Inc registered in the U S and other countries The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such marks by Philips is under license Note The type plate is located on the back of the unit 2 Your Wireless Microphone and Bluetooth Speaker Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips com welcome If you contact Philips you will be asked for the model and serial number of this apparatus The model number and serial number are on the back of the apparatus Write the numbers here Model No Serial No Introduction With the wireless microphone and Bluetooth speaker you can e dock your iPad onto the speaker to sing along with music from the app StarMaker Karaoke Auto
10. nnect the equipment into an outlet on a circurt different from that to which the receiver Is connected e Consult the dealer or an experienced radio TV technician for help Canada This Class B digital apparatus complies with Canadian ICES 003 Disposal of your old product and batteries Your product is designed and manufactured with high quality materials and components which can be recycled and reused Never dispose of your product with other household waste Please inform yourself about the local rules on the separate collection of electrical and electronic products and batteries The correct disposal of these products helps prevent potentially negative consequences on the environment and human health Your product contains batteries which cannot be disposed of with normal household waste Please inform yourself about the local rules on separate collection of batteries The correct disposal of batteries helps prevent potentially negative consequences on the environment and human health Please visit www recycle philips com for additional information on a recycling center in your area Environmental information All unnecessary packaging has been omitted We have tried to make the packaging easy to separate into three materials cardboard box polystyrene foam buffer and polyethylene bags protective foam sheet Your system consists of materials which can be recycled and reused if disassembled by a specia
11. r lt O 5W Consumption EN 13 6 Troubleshooting Warning Never remove the casing of this device To keep the warranty valid never try to repair the system yourself If you encounter problems when using this device check the following points before requesting service If the problem remains unsolved go to the Philips Web page www philips com support When you contact Philips make sure that the device Is nearby and the model number and serial number are available No power to the Bluetooth speaker e Make sure that the AC power plug of the device is connected properly e Make sure that there is power at the AC outlet e Asa power saving feature the speaker switches to standby mode automatically after staying idle for more than 15 minutes Switch on the speaker again see Switch on the Bluetooth speaker on page 7 No power to the wireless microphone e The batteries may be installed incorrectly or drained Install or replace the batteries properly see Install replace microphone batteries on page 7 e Asa power saving feature the microphone switches to standby mode automatically after staying disconnected from the speaker for more than 15 minutes To switch it on again you need to slide the OFF ON switch on the microphone to the OFF position and then back to the ON position No sound or poor sound e Adjust volume e Check the Bluetooth connection e Check whether you have starte
12. s to pair with the Bluetooth speaker automatically gt After successful pairing and connection the Bluetooth indicator turns solid blue 0 0 5 Find and download a tutorial from StarMaker Karaoke Auto Tune then tap Sing gt RECORD for how to sing along through the wireless microphone and Bluetooth speaker 5 O Clock 7 7 Things 99 Red Balloons A A Thousand Years 6 Select a song from StarMaker Karaoke Auto Tune and sing along through the wireless microphone EN 9 7 Use on the top of the Bluetooth speaker to adjust volume Note e If no prompt pops up on your iPad at step 1 you can go to Settings gt General gt About gt AEA7100 gt Find App for Accessory to install the app El e If automatic pairing fails press and hold on the speaker for more than 10 seconds to pair the microphone with the speaker manually If the wireless microphone remains disconnected from the Bluetooth speaker for more than 15 minutes it switches to standby mode automatically To switch it on again you need to slide the OFF ON switch on the microphone to theOFF position and then slide back to the ON position You can use controls available on the app to adjust sound effects If you experience howling or echo try to increase the distance between the microphone and speaker or adjust the angle of the microphone towards the speaker EN Play from
13. sired operation FCC Radiation Exposure Statement This equipment complies with FCC s and IC s RF radiation exposure limits set forth for an uncontrolled environment The antenna s used for this transmitter must be installed and operated to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter Installers must ensure that 20cm separation distance will be maintained between the device excluding its handset and users FCC rules This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with EN 3 the instructions may cause harmful interference to radio communications However there Is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Co
14. sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 Battery usage CAUTION To prevent battery leakage which may result in bodily injury property damage or damage to the unit e Install all batteries correctly and as marked on the unit e Remove batteries when the unit is not used for a long time e Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate Apparatus shall not be exposed to dripping or splashing keep it away from direct sunlight naked flames or heat MM Warning e Never remove the casing of this apparatus e Never lubricate any part of this apparatus e Never place this apparatus on other electrical equipment e Keep this apparatus away from direct sunlight naked flames or heat e Ensure that you always have easy access to the power cord plug or adaptor to disconnect this apparatus from the power Risk of overheating Never install
15. udio input cable not supplied AC MAINS e AC power socket EN 3 Get started Always follow the instructions in this chapter in sequence Connect power pa Caution e Risk of product damage Make sure that the power supply voltage corresponds to the voltage printed on the back of the unit e Risk of electric shock When you unplug the AC power cord always pull the plug from the socket Never pull the cord Before you connect the AC power cord make sure that you have completed all the other connections e Connect the AC power cord to e the AC MAINS socket on the back of the Bluetooth speaker e the wall power socket Switch on the Bluetooth speaker e Press O on the top of the Bluetooth speaker L The power indicator lights up white L The Bluetooth indicator flashes blue slowly e To switch the unit to standby mode press on the top panel e To switch the unit on from standby mode press again Tip e Ifthe speaker stays idle for more than 15 minutes it switches to standby mode automatically Install replace microphone batteries BE Caution e Risk of explosion Keep batteries away from heat sunshine or fire Never discard batteries in fire Danger of explosion if batteries are incorrectly replaced Replace only with the same or equivalent type Batteries contain chemical substances so they should be disposed of properly
Download Pdf Manuals
Related Search