AMX NXA-KLB
Contents
1. 1 If you removed the connectors previously re insert them into their proper loca tions on the touch panel This ensures that the Flat Bracket will not obstructing any of the connectors on the rear panel 2 Align the openings on the bottom of the Flat Lock Bracket to the securing locations on the eft side of the touch panel connector plate located under the connector plate cover as indicated in FIG 7 Security key k not included S Kensington Lock Security v Cable assembly 4 gt gt not included _ A b Connector plate cover Base Base Plate FIG 7 Flat Lock Bracket Components and Installation i AMX Keyed Lock screwdriver adapter 3 Insert two Keyed Lock Securing Screws into their respective locations FIG 7 4 Use the AMX Keyed Lock screwdriver adapter to tighten the screws and secure the Flat Lock Bracket to the base plate FIG 7 5 Assemble the Kensington Lock Security Cable not included Refer to the doc umentation provided by the lock manufacturer for details 6 Open the Lock to rotate the lock mechanism so that it can be inserted into the opening in the top of the Flat Lock Bracket FIG 8 Security key ry not included lt A Kol A Kensington Lock Security Cable 5 assembly not included 2 Flat Lock Bracket _ gt NN Lock insertion point FIG 8 Lock mechanism and insertion point 93 2259 10 For full2. warranty information refer to the AMX Instruction Manual s associated with your Product s 036 004 2870 4 05 2005 AMX Corporation All rights reserved The AMX logo is a trademark of AMX Corporation AMX reserves the right to alter specifications without notice at any time 3000 RESEARCH DRIVE RICHARDSON TX 75082 800 222 0193 fax 469 624 7153 technical support 800 932 6993 e www amx com Brus REV A banag Lr
3. are two versions of the Bracket included with the kit as indicated in FIG 1 FIG 2 Location of the securing locations on an NXT Table Top panel e The Flat Lock Bracket fits neatly into the rear of the panel s base allowing you to close the rear connector plate cover on the base while the panel is secured Method A Installing the Raised Lock Bracket e The Raised Lock Bracket also allows you to use the Kensington Lock System Note that once installed the shape of the Raised Lock Bracket will not allow the to secure the panel while providing a surface to which you can secure incoming Connector Plate Cover on the base of the panel to be closed capies 1 Raise the Connector Plate Cover and align the openings on the bottom of the fe Raised Lock Bracket to the securing locations on the Base Plate of the panel k FIG 2 ae Se amp i cS S ss Aoii AE RTAGKGL Kensington Lock Security Cable OR Keyed Lock Pa re ie assembly not included Can ce Securing Screws a ee gt ee Pa a Ean e ee e Connector plate cover p lt K Al AMX Keyed Lock screwdriver adapter Shey Based Lock Bracket Q a fits into any standard hex type x screwdriver or drill A Keyed Lock Securing Screws Flat Lock Bracket o gt AMX Keyed Lock screwdriver adapter FIG 1 NXA KLB Components FIG 3 Raised Kensington Lock Bracket Components and Installation Product Specifications NXA KLB Specifications 2 Insert two Keyed Loc
4. he securing loca Parente tion for the Kensington Lock Bracket FIG 2 FIG 4 Raised Securing locations 3 Determine which type of bracket Raised or Flat you will be installing e f your installation requires secured cables use the Raised Lock Bracket 4 Thread the incoming cables through the opening between the bottom of the Raised Bracket and the Base Plate FIG 4 5 Reconnect the cables on the rear connector plate 6 Thread a tie wrap not included through the center pair of circular openings on the bracket FIG 5 and use it to secure all of the NXA MTC RGB cables to the bracket Trim off any excess length on the tie wrap if necessary e f your installation requires a low profile security solution use the Flat Lock Bracket q Incoming cables FIG 5 Thread a tie wrap through the center holes on the Raised Lock Bracket 7 Assemble the Kensington Lock Security Cable not included Refer to the doc umentation provided by the lock manufacturer for details 8 Open the Lock to rotate the lock mechanism so that it can be inserted into the slot on the top center of the Raised Lock Bracket FIG 6 CSA Security key SS not included Kensington Lock Security Cable assembly not included Lock insertion slot FIG 6 Lock mechanism and insertion location AMX Corporation reserves the right to alter specifications without notice at any time Method B Installing the Flat Lock Bracket
5. k Securing Screws into their respective locations FIG 3 Compatible AMX NXT 1200V 12 Modero Video Table Top Panel FG2250 60 3 Use the Keyed Lock screwdriver adapter to tighten these screws securing the Touch Panels NXT 1200VG 12 Modero Multimedia Table Top Panel FG2250 61 Raised Lock Bracket to the base plate FIG 4 NXT 1500VG 15 Modero Multimedia Table Top Panel FG2252 61 NXT 1700VG 17 Modero Multimedia Table Top Panel FG2257 61 K tendons tv Cabl ensington Loc ecurity Cabie Requirements The NXA KLB must be used with a standard Kensington Lock System assembly not included Note The Kensington Lock System must be purchased separately and is not provided by AMX ii Thread incoming cables through this k opening between the Bracket and the Base an j 3 i Included Raised Lock Bracket with cable tie down black Accessories Flat Lock Bracket black AMX Keyed Lock screwdriver adapter Keyed Lock Securing Screws 5 lt q Raised Lock Bracket i Preparing the Touch Panel to Install the NXA KLB 1 Gently place the touch panel LCD facedown onto a soft cloth to expose the under side of the base and prevent scratching of the LCD FIG 2 e You may find it easier to handle the panel if you carefully detach all connectors Securing locations 2 _ Tilt the base forward so that the bottom surface of the base is easily accessible This provides access to the underside of the unit and exposes t
6. y baag Installation Guide az EAA irs rour woato taxe conton NXA KLB Kensington Lock Bracket for NXT 1200V and VG Series Panels Overview The NXA KLB FG2259 10 is an optional accessory for AMX Table Top NXT 1200V i N i SS Securing locations for Kensington Lock Brackets and VG Series touch panels which allows you to use a standard Kensington Lock System to prevent theft x Connector plate cover open to access the S connectors on the rear of the base The Kensington Lock System itself including lock key and security cable is sold separately The Kengsington Lock System is a security system from Kensington Technology Group www kensington com that discourages the theft of portable computers and other devices in this case touch panels by using a security cable and lock to anchor the panel to an object in the room The security cable is looped through a permanent object in the room then looped through itself and locked into the slot Once secured in this way the panel cannot be removed from its location unless it is unlocked using the C key that comes with the Kensington Lock assembly The NXA KLB Bracket attaches to the base of the Table Top 1200V and VG Series J panels listed below using keyed lock securing screws that can only be removed with SS the included AMX Keyed Lock screw driver adapter This screwdriver head fits into Base piate most hex type screwdrivers or electric drills There
Download Pdf Manuals
Related Search