Digitus DS-72001GE rack console
Contents
1. ro allt E PACKING LIST Type Name Num Uni Note t 17 inches LCD screen DS 72001GE US KVM Control Platform 1 keyboard and mouse control DS 72002GE US platform integrated KVM DS 72003GE US switch with multiple ports 8 16ports 19 inches LCD screen DS 72011GE US KVM Control Platform 1 keyboard and mouse control DS 72012GE US platform integrated KVM DS 72013GE US switch with multiple ports 8 16ports Cable KVM Connecting 1 8 16 PS 2 Connecting and USB Cable Connecting AC Power Power Cable 1 AC power connecting cable User Manual User Manual 1 Manual Please check the lists carefully and contact with your dealer if you have some problems Please read the manual carefully before installation KVM CONTROL PLATFORM CONNECTING WIRE Cable Type KVM Port PC or Server Port USB and PS 2 VGA port VGA Keyboard Mouse Connecting Keyboard Standard USB amp PS 2 Cable mouse and Interface monitor Sil wel 13 aldi eh a al e ln de Lo wm E USB and PS 2 Connecting Cable KVM CONTROL PLATFORM POWER WIRE Wire2. Hot Plug The KVM control platform supports hot plug It can be connected and disconnected without turning power off Please follow the steps Hot plug PC connecting port When hot plugging PC port 1 The connecting wire must be plugged into the port from which it is pulled out 2 Plug the mouse before plugging the keyboard Power On Off and Reboot Power on 1 Connect the computers to the KVM switch 2 Power on the KVM switch 3 Power on the PCs Reboot Ifthe KVM switch does not respond just press the reset button on the panel Assembling amp Disassembling The device can be assembled and disassembled as follows 13 STANDARD RACK INSTALLATION 1 Screw the front flange to the rack first Slide the bars with the rear flange towards the rack until the flanges gets contact with the rack then screw the rear flanges to the rack 2 Slide the switch onto the support flanges Use the screws supplied with this package to loosely attach the front of the switch to the front of the rack 3 Slide the rear attachment sliding brackets along the slide bars until they contact the rear of the switch 4 Use the screws supplied with this package to attach the bars to the rear of the switch SINGLE STAGE INSTALLATION To set up your installation do the following 1 2 Plug your USB PS 2 keyboard USB PS 2 mouse and moni
3. press Enter to enter a setting option CHANNEL DISPLAY MODE Mode of small tip window Choices and meanings are below Choice Meaning PN NAME Tip window displays port number and port name PN Tip window displays port number NAME Tip window displays port name Move the highlight bar to an option and press Enter to select it CHANNEL DISPLAY DURATION Time the tip window last Options are following 3 SECOND The tip window lasts for 3seconds ALWAYS ON The tip window always on the screen Move the highlight bar to an option and press Enter to select it CHANNEL DISPLAY POSITION Position of the tip window A small blue window appears on the screen Use arrow key to move it then press Enter to specify the position SCAN DURATION Duration for scanning one port Options are 3 seconds 5 seconds 10 seconds 15 seconds 20 seconds 30 seconds 40 seconds 60 seconds Move the highlight bar to an option and press Enter to select it OSD ACTIVATING HOTKEY Select OSD activating hotkey 9 Ctrl Ctrl Set hotkey as Ctrl Ctrl Scroll Scroll Set hotkey as Scroll Scroll 9 Shift Shift Set hotkey as Shift Shift Alt Alt Set hotkey as Alt Alt Move the highlight bar to an option and press Enter to select it SET PASSWORD Set new password First enter old password then enter new password and confirm it The new password is set If error occurs the screen will r
4. twice Note You can optionally change the hotkey to the Ctrl key in which case you would tap ctrl twice If OSD menu is set as console locked you must input password each time the main menu appears If no password has been set just press Enter to show main menu OSD menu interface is shown as below LISTALL OV PC NAME Note OSD always starts in List View with the highlight bar at the same position it was in the last time it was closed OSD NAVIGATION To dismiss OSD press Esc To move up and down through the list one line at a time use the Up and Down Arrow Keys If there are more list entries than what can appear on the main screen the screen will scroll To activate a port move the highlight bar to it then press Enter After selecting a port the OSD menu automatically disappear and a blue tip window appears to indicate the port currently selected OSD MAIN SCREEN HEADINGS Heading Explanation PN This column lists the port numbers for all the CPU ports on the installation The simplest method to access a particular computer is to move the highlight bar to it then press Enter QV If a port has been selected for Quick View scanning an arrowhead symbol displays in this column to indicate so PC The computers that are powered on and are on line have an arrowhead symbol in this column to indicate so NAME If a port has been given a name its name appears in this column
5. DIGIUS TFT Console User Manual INTRODUCTION siens nan Ri ah 3 FEATURE Sucio ii a tie ta 4 PRODUCT ITY BE HR E A AA 5 VIEW OF PRODUCT uscar rings 6 FIOD VIG W a il A do Sule re Pea cet LIE E r a 6 DIMENSION A adas 8 KVM SWITCHES PACKING LIST kk kk kK kk kK KK Kek kK KK KK KK KK kK KA 9 KVM Control Platform Connecting Wire 10 KVM Control Platform Power Wire 10 OPERATION z ta nano iia aaa ka el ee 11 CONNECTION OF KVM SIGNAL WIRE kk kk kk kek K k KK Kek KK KAK KA YA 11 Before Use een lee sets me tnt One balle nn ta RE Pt Et En 11 During USE ia HERR a Mr ana 11 After Use iia Senn rk ar ts 12 THOU O NO 12 Power On Off and Reboot ttrt ttrt ttrt ttrt trr rEEAEEEAEEEAEEEEEEEEEEEEEEEE EEEE reenen 12 Assembling amp Disassembling teeter kake kK K KAK KK YA 13 Single Stage Installation ss 15 Cascade Installation 16 OSD OPERATION 35 0 df kia aki liad dan n balk qa a raan k dadas 17 OSD OVEFVISW een A ee ehe DD tee e 17 OSD NavgatiO a x3 aa is 17 OSD Main Screen Headings ii 18 OSD R nclionser sn N e o ae gg 18 SAFETY GUIDE RE A A 21 INTRODUCTION A KVM control platform integrates a multiple port KVM switch into a 1U height It controls multiple PCs from only one platform keyboard mouse and monitor A KVM switch can control 8 16 PCs by direct connection and 256 PCs by 2 level cascade connection It is easy and q
6. OSD FUNCTIONS OSD functions are used to configure and control the OSD For example you can rapidly switch to any port scan selected ports only limit the list you wish to view designate a port as a Quick View Port create or edit a port name or make OSD setting adjustments F1 GOTO GOTO allows you to switch directly to a port either by keying in the port s name or its port number To use NAME method move highlight bar to NAME press Enter input name of a port then press Enter to confirm To use PN method move highlight bar to PN press Enter input port number then press Enter to switch If the port number is invalid it will remind the user to input again To switch to other BANK move highlight bar to BANK press Enter input bank number then press Enter to switch to the specified bank If the bank is invalid it will remind the user to input again Note When keying name if there is a matching name the matched name will appear on the screen just press Enter to switch to that port To return to main menu press Esc F2 SCAN The SCAN function can automatically scan from current selected port the scan interval can be set by users When scanning a small window on the screen indicates the current port number Press Space to stop scanning and the KVM switches to the port last scanned F3 LIST The LIST function lets you broaden or narrow the scope of which ports the OSD displays on the
7. Type Note Voltage Range Machine Type AC Power 3 Plugs of National 100 230V All Wire Standard IEEE AC Power Wire OPERATION CONNECTION OF KVM SIGNAL WIRE Connect the end with 8 sockets to the KVM control platform and the other one to the computer DC9V 8 7 6 5 4 3 2 1 ln a Tarn T FERNE cris gt 2 3 all lt HI dl Before Use e Make sure all the devices are safely grounded e Make sure the KVM wire and power wire are connected correctly During Use Pull the KVM control platform out from cabinet totally the guide locks automatically and the power turns on Release front lock As shown below e Then open the front panel and the LCD can be turn on to 120 degrees As shown below AUTO LOCK Li SA moc a o mea UNLOCK e Press LCD power key red the LCD is on After Use e Press LCD power key gt the LCD power turns off e Close LCD panel and lock the front panel e Release guide lock e Push the control panel into the cabinet totally and then the power turns off
8. emind users CLEAR THE NAME LIST Clear the names of port list You need to enter password to clear the names of port list RESTORE DEFAULT VALUE Restore settings to default value You need to enter password to Restore settings to default value Note The user password will also be cleared and the factory password will not LOCK CONSOLE Lock the console You cannot switch or scan after you lock the console including switch by push button on the panel or OSD You need to enter password to set Note After Locking the console you can also unlock the console by this option It also needs password verification 20 SAFETY GUIDE Please follow the directions below when installing using and maintaining it in order to guarantee the device to work well When installing and operating the device please make sure proper power supply first and then do other operations after it is initialized As signal and power transfer need custom cable please use matched cable unmatched cable may cause system work improperly or even damage the device Keep airy during operating to prevent high temperature Keep the device away from working long in wet environment to prevent short circuit Please do not open the device without permission of professionals 96 C 21
9. main screen Many of the OSD functions only operate on the computers that have been selected for listing on the main screen with this function The choices and their meanings are given in the table below Choice Meaning ALL Lists all of the ports on the installation QVIEW Lists only the ports that have been selected as Quick View Ports POWERED ON Lists only the ports that have their attached computers powered on POWERED ON Lists only the ports that have their attached computers powered on QVIEW and have been selected as Quick View Ports QVIEW NAME Lists only the ports that have been selected as Quick View Ports and have name NAME Lists only the ports that have names Move the highlight bar to the choice you want then press enter An icon appears before the choice to indicate that it is the currently selected one After you make your choice and press Enter you return to the OSD main screen with the newly formulated list displayed F4 QV QV function can select port as Quick View Move the highlight bar to a port press F4 an icon of up triangle appears Press F4 again the icon disappears F5 EDIT EDIT function creates or edits the name of a port Press F5 a pink edit box will appear on the screen Input name and then press Enter the port is set a name and it will also appear on the screen F6 SET SET function configures the OSD menu Move the highlight bar to an option
10. ol 256 PCs by 2 level cascade connection Be compatible with PS 2 USB standard interface Supports VGA SVGA XGA video input Accord with DDC DDC2 DDC2B standard and VESA standard Supports maximum resolution of 1920 x 1440p Support multiple operating systems WIN95 98 98SE ME 200 XP WIN 7 WIN NT UNIX LINUX PRODUCT TYPE OSD Type Function Note DS 72001GE US No 17 inches LCD screen keyboard and mouse DS 72002GE US Yes 17 inches LCD screen keyboard mouse and 8 16 DS 72003GE US ports USB KVM DS 72011GE US No 19 inches LCD screen keyboard and mouse DS 72012GE US Yes 19 inches LCD screen keyboard mouse and 8 16 DS 72013GE US ports USB KVM VIEW OF PRODUCT FRONT VIEW Front Panel Handle LCD screen Keyboard Mouse touch board Rear hang ear channel Guide Front hang ear LCD OSD control key O N 9 0I Q N REAR VIEW y 1 2 3 DS 72001GE US DS 72011GE US 1 DC 12V 1000Ma power socket 2 USB keyboard amp mouse port 3 PC connecting port GC ip q He ERK GS Grp Giro Geo Qiii Q TED Giro QUO Gr Ces d TEED CUED CTE DS 72003GE US DS 72013GE US 1 2 3 1 DC 12V 1000Ma power socket 2 USB keyboard amp mouse port 3 PC connecting port DIMENSION
11. tor into the console port section located on the unit s rear panel Using a KVM cable set plug the DB 15 connector into any available CPU port on the switch At the other end of the cable plug the keyboard mouse video cables into their respective ports on the computer Plug the power adapter cable into the switch s power jack then plug the power adapter into an AC power source Repeat steps 2 4 for any other computers you are connecting up This completes the single stage installation and you can turn on the power to the PCs NOTE The LCD KVM switch initially links to PC connected to the first CPU port Computer Computer KVM Cable Computer Computer CASCADE INSTALLATION To set up cascade installation do the following 1 Set up single installation as mentioned in SINGLE STAGE INSTALLATION 2 Connect one end of HDB15 cable to IN port of upper KVM and the other end to OUT port of lower KVM This completes the cascade installation and you can turn on the power to the PCs NOTE The LCD KVM switch initially links to PC connected to the first CPU port Computer Computer Computer Computer gt J N o PS 2 USB SA cho PS 2 USB s C KVM Cable Computer Computer 16 OSD OPERATION OSD OVERVIEW The On Screen Display OSD is used to handle all computer control and switching procedures All procedures start from the OSD main menu To pop up the main menu tap the Scroll Lock
12. uick to install Just connect the wire to the correct port without software configuration So there is no difficulty in installation and incompatibility A KVM switch provides two methods to control the computers connected to it 1 By keyboard combine key 2 By OSD operation In addition it provides a powerful automatic scanning function to scan and monitor all computers connected to it Using a KVM control platform is the best choice to save time and money By using one KVM platform to manage all the computers connected to it the user can save money for keyboard mouse and monitor for each PC and their space FEATURES Control Platform Control platform with LCD keyboard mouse and multiple ports KVM switch 1U height suitable for 19 standard cabinet installation and metal structure 17 19 LCD screen with high brightness high clear and high resolution Control platform can be totally pulled out from the cabinet and the LCD screen can be turned on to 120 degrees Ultra thin keyboard with keypad Mouse touch board with two function button Front panel with lock to prevent damage by accident 9 Built in power Automatic power on off When pulling control platform out from cabinet the power turns off automatically When pushing it into the cabinet the power turns on automatically An easy to use OSD menu Switch One control platform can control 8 16 PCs by direct connection One control platform can contr
Download Pdf Manuals
Related Search