Gembird EG-PM2-LAN power extension
Contents
1. 4 20 12. Gembird www gembird ua 044 4510213 65 brands logos are registered trademarks of their respective owners
3. 10 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE Lo sms The sockets Socket 1 Socket 2 Socket 3 and Socket 4 can be managed or pre programmed by computer via LAN They are called manageable sockets in this manual The manageable sockets of EG PM2 LAN can be programmed to be on or off The current status of each manageable socket is represented by the corresponding indicator which will be lit if socket has power to it e Main rocker switch Z see Figure 1 above is turned off then the manageable sockets cannot be switched on by either web server Power manager software or the hardware schedule e As soon as you turn the Main rocker switch Z on then the web server Power manager software or the hardware schedule will be able to turn the manageable sockets on and off e Master switch button B see Figure 2 above can also switch all the manageable sockets on and off regardless of their current status or schedule that is being executed To switch them on you should keep the button pressed for 1 2 seconds To switch them off you should keep the button pressed for more than 3 seconds To protect the connected devices from possible high current and short circuit EG PM2 LAN is equipped with the automatic circuit breaker built in Main rocker switch e NOTE If the total power consumption or peak power of the
4. All the IP settings and device settings will remain the same as before but the server time will be reset and all schedules will become outdated 41 All brands and logos are registered trademarks of their respective owners nr EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE ast 6 2 Managing EG PM2 LAN After successful connection close LAN devices window You can now start managing EG PM2 LAN via the Power Manager interface Double click on the socket icon in the system tray or select Open from the popup menu see Figure 14 above You will get the window of the main control panel shown on the Figure 19 below Figure 19 Power Management x Socket 1 Socket1 Socket 2 Socket2 Socket 4 Socke AN uu ON ANAGER PMS2 LA 42 brands and logos are registered trademarks of their respective owners A EG PM2 LAN PROGRAMMABLE POWER energenle OUTLET STRIP WIT LAN INTERPAGE Sockets should switch on and off green color means the socket is switched on red color means the socket is switched off when you double click on them Click the Settings button for each socket to access the Settings dialog box see Figure 20 below Figure 20 Device EG PMS2 LAN Socket Socket System tray Hot Key a Windows startup and shutdown events Hardware schedule On Windows startup now Software schedule Bl On Windows shutdown enie m energ POWE
5. IP addresses of the found EG PM2 LAN devices will appear in the list box Select EG PM2 LAN which you want to access and press the Open button see Figure 4 below 15 All brands and logos are registered trademarks of their respective owners 1 EG PM2 LAN PROGRAMMABLE POWER energente UTLEY STRIP WIT LAN INTERFACE Figure 4 Find EG PMS LAN Connect EG PMS LAN to the LAN or directly to this PC first If you performed a hardware reset of EG PMS LAN wait for 10 seconds Where to search Adapter subnet Adapters From 192 0 1 wireless Network Connection To 192 168 0 254 Search Stop IP addresses of the found devices _ Open The window of your default internet browser will be then opened to give you access to the built in web server See section 4 below for the further details 16 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE aet 4 The web server Your EG PM2 LAN is equipped with a web server which allows managing the device using any web browser such as Internet Explorer etc 4 1 Web server login page To access the web server of EG PM2 LAN just open Internet Explorer or other browser and input the IP address of EG PM2 LAN for example http 192 168 1 241 If you have used Find EG PM2 LAN utility to locate EG PM2 LAN then you will be taken to this webpage automaticall
6. POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE aget Below the page you can see the current time of the web server and eventual information about the last successful timer synchronization Automatic timer synchronization is used if Use NTP for timer correction option is enabled see section 4 6 below NOTE If a certain socket has a switching fault e g it should be Switched on but the whole device is switched off or it should be off but it does have voltage then the warning message Wrong voltage on socket will be shown above the Event schedule see Figure 7 above This message might also indicate that this socket is defective For setting up the socket schedule click Set schedule button You will face then the page shown below see Figure 8 23 All brands and logos are registered trademarks of their respective owners Server 1 Figure Socket 1 schedule EG PM2 LAN PROGRAMMABLE POWER OUTLET STRIP WITH LAN INTERFACE 8 Status 9 wj Jut 2 OFF 2012 14 20 2012 14 30 15 M Periodic M x 00 Periodic x 2012 9 14 40 80 Once _ x OFF 9 suu 2012 14 50 iw 45 once EnerGenie Add event Days Hours Minutes Seconds Loop period 1 0 0 Socket 1 Socket 2 Clear schedule Socket 3 Socket 4 Socket Name Settings Device Settin
7. POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE aget On the LAN settings page see Figure 10 above you can set up DHCP IP address Subnet mask Gateway DNS server and IP filter up to 3 IP addresses can then be enabled for remote access The new settings will be applied immediately after you press the Apply button IP address Subnet mask Gateway DNS server will be used only if the DHCP option is disabled If you set DHCP option it is recommended for your own convenience to set up your DHCP server so that it always provides the same IP address to EG PM2 LAN To do that you will need to know the MAC address of EG PM2 LAN It can be found on this page or on the bottom sticker of the device The MAC address is fixed and cannot be changed DNS server address is important to be properly set up in case you wish to enable the NTP timer correction option see section 4 6 below IP filter option is needed to prevent unauthorized access to the server It restricts the web server access from any computer with IP address different from IP1 IP2 and IP3 Make sure that you input IP1 IP2 and IP3 correctly before enabling this option Power Manager client port is used for connecting with the Power Manager software normally it is not needed to change this setting 28 All brands and logos are registered trademarks of their respective owners energenie EG PM2 LAN PROGRAMMABLE POWER 4 6 Device settings page OUTLET STRIP WITH LAN INTER
8. WITH LAN INTERFACE aget Figure 27 Application events Path name Onrun On exit Switch scanner on off CNWIND WS system32 mspaint exe Switch Switch OFF Switch printer on off CAWINDOWS system32 spool PRINTERS Switch ON Switch OFF e To add a new program event click the Add app button The Add program event dialog will appear see Figure 28 below 53 All brands and logos are registered trademarks of their respective owners MA 1 EG PM2 LAN PROGRAMMABLE POWER energenle OUTLET STRIP WHT LAN INTERFACE Figure 28 Add program event Event me 1 dL Onrun Switch ON v On exit Switch OFF v Enabled Specify the application title and path to it using the Browse button or typing it manually in the Title and Path name fields If you use the Browse button you can also select a shortcut to the application In this case the application title and path name will be taken automatically via the shortcut if possible After you have specified the application check On run and or On exit and choose the event switch on or off 54 All brands and logos are registered trademarks of their respective owners 1 EG PM2 LAN PROGRAMMABLE POWER ene rgenie OUTLET STRIP WITH LAN INTERFACE NOTE The On run event will take place when the first window of the selected application is opened The On exit event will take place when the last window of the application is closed HINT Your dev
9. Wa expiration date ihr Zeichen Client Reference tates 15 11 2017 9 00 Unser Zeichen Our Reference 05 17014557 001 Genehmigungsinhaber License Holder Fertigungsst tte Manufacturing Plant GEMBIRD ELECTRONICS LTD Gembird Electronic Ltd la 2103 21 F Office Tower 2 F Building B Shifeng Industry Langham Place 8 Argyle Street District Huaning Road Longhua Mongkok Dalang Street Baoan Distri g Kong Shenzhen China Pr fzeichen Test Mark Gepr ft nach Tested acc to 0620 1 02 10 20024A2 EN 61058 Der Anhang 1 der Richie 20069S RG is eingehalten Das Zertifikat kann im Rahmen der Korformitiseriirung nach Anhang II verwendet werden Amer 1 ef de directive 2008595 EC ts complied Wich The cercate can be used in connection with the EC declaration of conformity arc 19 Anner I Lizenzentgelte Einheit License Fee Unit Zer fiziertes Produkt Ger teidentifikation Certified Product Product Identification Steckdosenleiste Portable Socket outlet IAN BG PM2 E Bemeseungespannung AC 2507 Rated Voltage Benessungestrom 10A Rated Current Schutzklasse 1 Protection Class HOSWV F 361 Smm LR 5 ANLAGE Appendix 1 Dem lege unsere Prif und Zerifieknungsordnung zugrunde Produkt anl Feruguagssdue erf len 20 und y 21 der Zertifizierungsstelle This based on cur Ting and Regulation Pr
10. de huidige marktprijs voor het defecte produkt l utilisateur final Le talon de garantie doit num rer clairement la date d achat et le type d appareil Conservez le recu d achat pendant toute la dur e de la garantie car elle est n cessaire pour toute r clamation Au cours de la p riode de garantie tous les d fauts doivent tre remplac aux frais du fabricant soit par la r paration ou la remplacement de la pi ce d fectueuse ou l ensemble du produit Les travaux effectu s sous garantie ne prolongent pas la p riode de garantie ni ne commencent pas une nouvelle p riode de garantie Le fabricant se r serve le droit d annuler toute demande de garantie pour les dommages ou d fauts dus une mauvaise utilisation abus ou les effets externes chute choc p n tration de l eau la poussi re etc Les pi ces d usure par exemple les piles rechargeables sont exclus de la garantie D s r ception de la marchandise sous garantie le SAV de Gembird Europe BV se r serve le droit de choisir entre le remplacement des produits d fectueux ou de d livrer un avoir Le montant d avoir sera toujours calcul e sur la base de la valeur actuelle du march des produits d fectueux Gembird Europe B V Gembird Europe B V Wittevrouwen 56 1358CD Almere The Netherlands www gembird nl support ort gmb nl Tel 31 36 5211588 0 15 p m binnen Nederland Wittevrouwen 56 1358CD Almere The Netherlands www gembird nl supp
11. device name socket name Examples e C Program Files Energenie Power Manager pm exe on My EnerGenie Socket1 E Utils PM3 pm exe off My EnerGenie Table lamp e Execute pm exe with info key info to get the complete information about the status of the current devices For each of the connected devices the following information will then be provided and placed into nfo ini file in the Power Manager folder e DeviceName the user specified device name e Socket name where is replaced by a certain socket number the user specified socket name 58 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE Lo sms e Socket SwitchState where is replaced by a certain socket number TRUE when the socket is switched on FALSE when the socket is Switched off e Socket VoltageState where is replaced by a certain socket number TRUE when voltage presence on the socket is detected FALSE when there is no voltage on the socket Example NOTE Each use of this command line option totally overrides the data in Info ini file NOTE Power Manager should be active 9 EG PM2 LAN SDK For advanced users we supply the software development kit SDK to manage the device Check the SDK manual in SDK folder on the supplied CD to get more information about it 59 All brands and logos are registered trademarks
12. for the timer schedule so the timer schedule remains active even when EG PM2 LAN is temporarily turned off 1 2 Specifications Input voltage max 250 V AC 50 60 Hz Maximum load current 10 A Maximum power consumption 2 5 W Built in power supply Power cord 1 8 m Hardware schedule possibilities Maximum number of independent hardware schedule events 45 per Socket Time setting accuracy in seconds Combine periodical and once events All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE aet e Timer accuracy not more than 2 seconds error per day in case that power is always present Otherwise there can be an additional up to 2 seconds error per each power off e Indoor use e Net weight 1 Kg 1 3 Hardware requirements e Local area network with RJ45 sockets Any Internet enabled computer connected to the local area network e Computer running Windows 2000 XP Vista 7 8 is required for using the Power Manager software use of this software is not compulsory 1 4 Package contents EG PM2 LAN User manual and Quick installation guide RJ45 cross over cable red RJ45 LAN cable grey CD with Power Manager software for Windows All brands and logos are registered trademarks of their respective owners Den i EG PM2 LAN PROGRAMMABLE POWER e ne OUTLET STRIP WITH LAN INTERFACE 2 Indicators and
13. of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE Lo sms 10 Troubleshooting The load connected to the device is too high some of the devices connected to the EG PM2 LAN should be disconnected before the rocker switch can be turned on The switching command is not There is no power supply to the EG PM2 carried out the rocker switch LAN Please make sure the EG PM2 LAN and indicators are not lit is connected to the power supply and the rocker switch is switched on The status of EG PM2 LAN in Try to ping the device see section 6 1 Power Manager does not above become Connected EG PM2 LAN is connected to local network ping test is ok but not responding The rocker switch turns off Reset EG PM2 LAN by pressing the Reset button on the side control panel see Figure 2 above or switch it off and then on again using the Main rocker switch Z see Figure 1 above Make sure EG PM2 LAN is connected to LAN Connection to EG PM2 LAN is and switched on Launch Find EG PM2 LAN lost It seems something is utility You can also try to use IP config C wrong with its IP address button to let the device renew its IP address see section 3 2 above 60 All brands and logos are registered trademarks of their respective owners energente Zertifikat Certificate Zertifikat Nr Certificate No Blatt Page T VRheinland S1 50187883 0001 L npicas gg
14. 16 112012 T V Rheinland LGA Products GmbH Tillystra amp e 2 9 31 N rnberg The CE marking may be used if all relevant and affective EC Directives are complied with 61 All brands and logos are registered trademarks of their respective owners H energente EG PM2 LAN PROGRAMMABLE POWER OUTLET STRIP WITH LAN INTERFACE Waste disposal Do not deposit this equipment with the household waste Improper disposal can harm both the environment and human health For Information about waste collection facilities for used electrical and electronic devices please contact your city council or an authorized company for the disposal of electrical and electronic equipment Entsorgungshinweise Werfen Sie dieses Ger t nicht in den Hausm ll Entsorgung kann sowohl der Umwelt als auch der menschlichen Gesundheit schaden Informationen zu Sammelstellen f r Altger te erhalten Sie bei Ihrer Stadtverwaltung oder einer autorisierten Stelle f r die Entsorgung von Elektro und Elektronikger ten Richtlijnen m b t afvalverwerking E xl ii Batterijen en accu s dienen als klein chemisch afval afgeleverd te worden bij toegewezen afvalverzamelpunten zie www afvalgids nl U dient ervoor te zorgen dat de batterijen accu s leeg zijn en dus geen stroom meer kunnen leveren Let op de batterijen accu s dienen onbeschadigd ingeleverd te worden Gooi dit product niet weg in uw vuilnis
15. 5 All brands and logos are registered trademarks of their respective owners EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE agent Figure 9 EnerGenie LAN Power Manager Microsoft Internet Explorer Edit View Favorites Tools O O 26 Part 2 2 Address http 192 168 2 10 name_settings html Server 1 Socket Name Settings Socket 1 Socket 1 Socket 2 Socket2 Socket 3 Socket 3 Socket 4 Socket 4 EnerGenie Socket 1 Socket 2 Socket 3 Socket 4 Socket Name Settings Device Settings LAN Settings Log Out 26 All brands and logos are registered trademarks of their respective owners EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE w 4 5 LAN settings page Figure 10 EnerGenie LAN Power Manager Microsoft Internet Explorer Ele Edit View Favorites Tools Help Oz MAG yere SER Address http 192 168 2 10 lan_settings html Server 1 LAN settings Obtain IP va onergenie uc M Subnet mask EnerGenie Gateway DNS server Socket 1 IP filter Socket 2 es Socket 3 IP 2 IP 3 Socket 4 MAC address Socket Name Settings Power Manager client port Device Settings LAN Settings Log Out 27 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE
16. Device Name Name PMS2 LAN Device IP Device IP 192 168 1 201 Port Pott Password Cc Password Enabled Enabled US Sockets Specified device should then appear with a green square next to it and Connected status in the LAN devices window see Figure 17 below 38 All brands and logos are registered trademarks of their respective owners EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE w Figure 17 x energenie POWER MANAGER Device Window DEVICE NAME CONNECTION ELLEN NM To edit the LAN device select it and click the Edit button or just double click on the LAN device 39 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE aget To remove the LAN device select it and click the Remove button You can select multiple LAN devices using Ctr and Shift keys You can also remove all LAN devices by clicking the Clear button HINT Use the popup menu which can be activated by the right mouse button click over the table If the status of EG PM2 LAN shows the device not to be Connected it could be due to the following reasons Incorrect IP Port Password specified in the Add LAN device window e PC is not connected to the local network e You are trying to access EG PM2 LAN from the PC which is not allowed to do so Change PC IP address or change P filter
17. EG PM2 LAN PROGRAMMABLE POWER OUTLET STRIP WITH LAN INTERFACE USER MANUAL HANDBUCH HANDLEIDING MANUEL DESCRIPTIF EG PM2 LAN PROGRAMMABLE POWER OUTLET STRIP WITH LAN INTERFACE enersenle PROGRAMMABLE POWER OUTLET STRIP EH WITH LAN INTERFACE PROGRAMMIERBARE STECKDOSENLEISTE MIT LAN ANSCHLUSS PROGRAMMEERBARE STEKKERDOOS MET LAN INTERFACE BO TIER COMMAND DISTANCE PROGRAMMABLE AVEC PRISE LAN 1 3 LAN e Do not plug several sockets line e not use if covered e De energized only if power plug is unplugged NEVER connect appliances which do not allow unattained operation All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE Lo sms 1 Introduction Your EG PM2 LAN is an advanced power outlet strip with power management features Four sockets are individually manageable via the LAN interface The sockets can be switched on off by a timer schedule by user or different events It is also possible to pre program the unit event
18. FACE On the device settings page you can setup name password and internal time of EG PM2 LAN see Figure 11 below Figure 11 EnerGenie LAN Power Manager Microsoft Internet Explorer Edit View Favorites Tools Help BAG Dx 6 Address http 192 168 2 10 device settings html Server 1 energenie EnerGenie Socket 1 Socket 2 Socket 3 Socket 4 Socket Name Settings Device Settings LAN Settings Log Out Device settings Server name Server 1 Password Set device time Use NTP fortimer 2 correction NTP server pool ntp org Le 29 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE aget To be able to setup the schedule of EG PM2 LAN you have to first setup its internal clock correctly Enter the current local time and date Alternatively if the option Use NTP for timer correction is enabled by default then the time will be taken from NTP server The device will try to connect with the server every 18 hours The first synchronization would take place in 15 seconds after you press the Apply button NTP server field should have a valid name of NTP server by default pool ntp org If for any reason the NTP time correction doesn t work you can choose the best NTP server for your country via the website www pool ntp org NOTE for NTP t
19. INT If you have several printers connected to the same computer we suggest moving default spool directory of each printer to a separate location To edit the event select it and click the Edit button or just double click on the event see Figure 27 above The Edit file event window will appear see Figure 30 below 56 All brands and logos are registered trademarks of their respective owners MA 1 EG PM2 LAN PROGRAMMABLE POWER energente UTLEY STRIP WITH LAN INTERFACE Figure 30 Edit file event r Event Title Switch printer on off Path CAWINDOWS system32 spoohPRINTERS m File name 5 On placing Switch v Delay on placing n removal Switch OFF v Delay on removal 1 minutes v Enabled To remove the event select it and click the Remove button see Figure 27 above You can select multiple events using and Shift keys You can also remove all events by clicking the Clear button HINT Use the popup menu which can be activated by the right mouse button click over the table 57 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE Lo sms 8 Managing EG PM2 LAN via your own software To let you switch the sockets from your own applications the following command line interface syntax is supported e pm exe on off
20. Loop period Mi e After the schedule record has been created click the Apply button see Figure 21 above to save the hardware timer schedule changes In case of incorrect entries these will be highlighted and an error message will appear Click the Apply button again after correcting all the errors e Use Sync button see Figure 21 above to synchronize device timer with PC clock Note that after synchronization past entries will be removed from the schedule HINT Use the popup menu see Figure 21 above which can be activated by the right mouse button click over the table 47 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE aget NOTE The hardware schedule keeps running even when the device is powered off However it is recommended not to power off the device for longer than 1 week because the built in battery might get discharged then In this case the internal clock of the device would be reset and as result some schedule events would not be executed Besides all the Sockets would lose their previous status they will be switched on Leave the device switched on for one day to fully charge the battery 7 2 Setting up software schedule Using the Software schedule button available from the Settings window see section 6 2 above you can create the software timer schedule see Figure 24 below NOTE the softwar
21. N activity taking place e The indicator Schedule see Figure 2 above blinks red as the reset procedure is being executed e indicator Schedule see Figure 2 above stays red if an active hardware schedule for any socket exists e The indicator Power see Figure 3 above stays on if EG PM2 LAN is connected to the power supply and active All brands and logos are registered trademarks of their respective owners EG PM2 LAN PROGRAMMABLE POWER OUTLET STRIP WITH LAN INTERFACE 3 Installation It is strongly recommended to avoid damp or wet places for installation EG PM2 LAN should be connected to the European AC wall socket of the standard DIN 49 440 Do not plug several sockets in line Do not use if covered De energized only if power plug is unplugged NEVER connect appliances which do not allow unattained operation 3 1 Getting started Connect EG PM2 LAN to the wall socket first and then to the LAN Socket or your computer LAN card with the provided patch cord or vice versa EG PM2 LAN can now be switched on and off by means of the Main rocker switch Z Two non manageable sockets are switched on and off by means of the Main rocker switch Z and cannot be managed by the computer so they are called non manageable sockets in this manual If EG PM2 LAN is switched on then the indicator POWER is lit In this case both non manageable sockets are now ive and connected to the power supply
22. RMANAGER Close You can choose a different device and another socket from the Device and Socket drop down list boxes 43 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE Lo mms e It is possible to give a name to the device and socket for example Printer or Scanner using the Rename button Check the System tray checkbox if you want to put the icon of the socket into the system tray You can choose the icon from drop down list box Such icon is a fast way to switch the device connected to the socket on off or check the device status e You can also assign a hot key to switch the socket on off Check the Switch ON and Switch OFF checkboxes and specify the hot keys e To switch the socket on off on Windows startup wake up check the On Windows startup checkbox and choose the required action e To switch the socket on off on the Windows shutdown sleep check the On Windows shutdown checkbox and choose the required action 44 All brands and logos are registered trademarks of their respective owners A 1 EG PM2 LAN PROGRAMMABLE POWER energenle OUTLET STRIP WHT LAN INTERFACE 7 Power Manager core features 7 1 Setting up the hardware schedule Using the Hardware schedule button available from the Settings window see section 6 2 above you can create the hardware timer schedule see Figure 21 below To add a new record
23. TepMiHy 2 3 4
24. WITH LAN INTERFACE w e To edit the task select it see Figure 24 above and click the Edit button or just double click on the task The Edit task window will appear see Figure 26 below Figure 26 Edit task Switch OFF time 2038 19 08 2010 Perform task every 1 days v Comment Do Enabled e To remove the task select it and click the Remove button see Figure 24 above You may select multiple tasks using Ctr and 51 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE aget Shift keys You can also remove all tasks by clicking the Clear button HINT Use the popup menu which can be activated by the right mouse button click over the table see Figure 24 above 7 3 Setting up application events Using the Application events window you can specify the socket events when a certain application is launched or closed down You can also associate switching the sockets off or on with placement and removal of particular files in certain folders To use this feature push Application events button available from the Settings window see section 6 2 above Figure 20 You will get the following window see Figure 27 below 52 All brands and logos are registered trademarks of their respective owners bul 2 PROGRAMMABLE POWER rge nie OUTLET STRIP
25. act falling down impact ingress of water dust contamination or break Wearing parts e g rechargeable batteries are excluded from the warranty Upon receipt of the RMA goods Gembird Europe B V reserves the right to choose between replacement of defective goods or issuing a credit note The credit note amount will always be calculated on the basis of the current market value of the defective products Die Garantie betr gt 24 Monate ab Verkaufsdatum an den Endverbraucher Das Kaufdatum und der Ger tetyp sind durch eine maschinell erstellte Kaufquittung zu belegen Bitte bewahren Sie Ihren Kaufbeleg daher f r die Dauer der Garantie auf da er Voraussetzung f r eine eventuelle Reklamation ist Innerhalb der Garantiezeit werden alle M ngel wahlweise durch den Hersteller entweder durch Instandsetzung Austausch mangelhafter Teile oder im Austausch behoben Die Ausf hrung der Garantieleistung bewirkt weder eine Verl ngerung noch einen Neubeginn der Garantiezeit Eine Garantieleistung entf llt f r Sch den oder M ngel die durch unsachgem e Handhabung oder durch u ere Einwirkung Sturz Schlag Wasser Staub Verschmutzung oder Bruch herbeigef hrt wurden Verschlei teile z B Akkus sind von der Garantie ausgenommen Gembird Europe B V Wittevrouwen 56 1358CD Almere The Netherlands www gembird nl support ort gmb nl Tel 31 36 5211588 GEMBIRD Deutschland GmbH Coesterweg 45 59494 Soest Deutschland www ge
26. al IP address To setup this free service you should follow two simple steps 18 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE aget e Register the device To restrict access to the device via the Internet to the rightful owner only the device should be registered e g assigned to your account To register the device simply push the button Register on this page see Figure 6 below You will then be redirected to Login page of EnerGenie com If you already own an account at EnerGenie com then just enter your login and password on this page and you are done Otherwise use the Registration button on the Login page to create a new account After your successful login regardless whether you created a new or used an existing account your EG PM2 LAN is automatically registered Return back to the EnerGenie page of your EG PM2 LAN see Figure 6 below Push Activate button to let the device initiate communication with EnerGenie com server The EnerGenie page will then start updating itself until the Status becomes Registered Activated Connected see Figure 6 below 19 All brands and logos are registered trademarks of their respective owners EG PM2 LAN PROGRAMMABLE POWER e ne rgenie OUTLET STRIP WITH LAN INTERFACE Figure 6 EnerGenie LAN Power Manager Microsoft Internet Explorer Ele Edit View Favorites Tool
27. atic setup does not work then open CD ROM drive in the My Computer window and launch SETUP EXE from the CD e Follow instructions of the installation software NOTE Antivirus or firewall software may block connection to EG PM2 LAN Please configure antivirus firewall to permit connection to the IP address and port of your EG PM2 LAN 14 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE aget 3 4 IP configuration The utility Find EG PM2 LAN see Figure 4 below will run automatically during the software installation but it can also be started from Start All Programs Gembird Power Manager The IP range where you would like to search for EG PM2 LAN will be set automatically according to the IP settings of your LAN adapter but can be changed manually in the Adapter subnet fields Now press the Search button NOTE only EG PM2 LAN within a local subnet can be found If your computer LAN adapter is not in the default subnet of EG PM2 LAN as might probably be the case if you chose option B section 3 2 you will have to change its IP address manually to be able to find EG PM2 LAN For example if you wish to find EG PM2 LAN with the default IP 192 168 0 254 the IP address of your computer should be set as 192 168 0 XXX where XXX stands for any digit for example 1 and the subnet mask should be 255 255 255 0 After the searching the
28. bak Dit kan zowel het milieu als de menselijke gezondheid schade toebrengen Informatie over het inleveren van dit product kunt u inwinnen bij uw gemeentelijke vuilnisdienst of andere geautoriseerde instelling in uw buurt Traitement des d chets Ne jetez pas cet appareil dans les d chets domestiques Un traitement inappropri peut tre dommageable l environnement et la sant humain Vous trouvez des informations sur les centres de rassemblement des appareils vieux chez l administration municipale ou chez un centre autoris pour le traitement des appareils lectriques ou lectroniques 62 All brands and logos are registered trademarks of their respective owners NR H energente EG PM2 LAN PROGRAMMABLE POWER OUTLET STRIP WITH LAN INTERFACE WARRANTY CONDITIONS GARANTIE BEDINGUNGEN The warranty period is 24 months and begins with the sale to the end user The receipt must clearly list the date of purchase and the part number in addition it should be printed Keep the receipt for the entire warranty period since 15 required for all warranty claims During the warranty period the defective items will be credited repaired or replaced at the manufacturer s expense Work carried out under the warranty neither extends the warranty period nor starts a new warranty period The manufacturer reserves the right to void any warranty claim for damages or defects due to misuse abuse or external imp
29. click the Add button Hardware schedule 14 03 40 09 07 2012 e 14 10 20 09 07 2012 9 15 03 32 03 07 2012 15 07 57 09 07 2012 4 Every 1 day Switch Switch OFF Switch Switch OFF 45 All brands and logos are registered trademarks of their respective owners N EG PM2 LAN PROGRAMMABLE POWER e ne rge nte OUTLET STRIP WITH LAN INTERFACE aset The window Add entry will appear see Figure 22 below In the dialog box specify the required time and the action Figure 22 Add entry Entry Time 140427 09 07 2012 Action SwitchoN v edit the record select it and click the Edit button or just double click on the entry see Figure 21 above The same window will appear see Figure 22 above To remove the record select it and click the Remove button see Figure 21 above You can select multiple entries using Ctr and Shift keys You can also remove all entries from the schedule by clicking the Clear button see Figure 21 above To set the period for periodic events for example if you want to perform the same events every day use the Loop button see 46 All brands and logos are registered trademarks of their respective owners t M EG PM2 LAN PROGRAMMABLE POWER e ne rge nte OUTLET STRIP WITH LAN INTERFACE ust Figure 421 above and specify the loop time period in the Edit loop period window see Figure 23 below Figure 23 E dit loop period
30. controls of the EG PM2 LAN Figure 1 Non manageable socket Manageable socket 4 Manageable socket 3 Manageable socket 2 Manageable socket 1 Non manageable socket Indicator Power Indicator Socket 4 Indicator Socket 3 Indicator Socket 2 Socket 1 Side panel All brands and logos are registered trademarks of their respective owners 1 EG PM2 LAN PROGRAMMABLE POWER ene OUTLET STRIP WITH LAN INTERFACE Figure 2 Indicator Schedule Reset Button A Master Switch Button B IP Config Button C LAN socket with LAN activity indicators All brands and logos are registered trademarks of their respective owners M 1 EG PM2 LAN PROGRAMMABLE POWER ene OUTLET STRIP WITH LAN INTERFACE Figure 3 Power cord Main rocker switch Z with power indicator and self recovering fuse On Reset after power consumption exceeds 2500 Watts All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE aet 2 1 Indicators e Main rocker switch Z see Figure 3 above is lit this means that EG PM2 LAN is connected to the power supply and active e The indicator Socket 1 2 3 4 see Figure 1 above is lit this means that this particular socket is switched on e indicator LAN activity see Figure 2 above blinks green this means that there is some LA
31. devices connected to EG PM2 LAN exceeds 2500 Watts the circuit breaker may power EG PM2 LAN off In this case please remove 11 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE at the excessive load first and then after 2 3 minutes press the main rocker switch 2 to restore the power supply see Figure 3 above To be able to use EG PM2 LAN you will now have to complete its LAN configuration 3 2 Preparing LAN configuration of EG PM2 LAN Before configuring EG PM2 LAN hardware settings please let it obtain its IP address Follow the steps below e Make sure EG PM2 LAN is connected to the local network with the provided RJ 45 cable option A recommended NOTE by default the factory setting of EG PM2 LAN is DHCP enabled If your LAN has a router with built in DHCP server which is very common then EG PM2 LAN will automatically get an IP address from the DHCP server Proceed to section 3 3 below in this case NOTE you may prefer to connect EG PM2 LAN directly to the managing computer LAN adapter network card using the supplied crossover RJ 45 cable option B You might need to use this option if your LAN does not have DHCP server 12 All brands and logos are registered trademarks of their respective owners EG PM2 LAN PROGRAMMABLE POWER rgente OUTLET STRIP WITH LAN INTERFACE If you choose for opt
32. e able to manage preconfigured EG PM2 LANs please do the following e Install Power Manager software on a PC connected to your local network A socket icon will then appear in your system tray e With a right mouse click on the socket icon you will get access to the Power Manager main menu see Figure 14 below 35 All brands and logos are registered trademarks of their respective owners N EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE agn Figure 14 x energenie POWER MANAGER Device Window DEVICE NAME CONNECTION ELLEN anim Please select Device Add Device or press Ctrl A see menu on Figure 15 below 36 All brands and logos are registered trademarks of their respective owners H EG PM2 LAN PROGRAMMABLE POWER ene OUTLET STRIP WITH LAN INTERFACE Figure 15 Add device Ctrl 4 Remove Device Del In the Add LAN device window see figure 16 below please enter correct IP address port number 5000 by default and password 1 by default as configured on the Device settings page see section 4 6 above of the web server To disconnect from the device uncheck the option Enable set this option again to regain the access Click OK button to return to the LAN devices window 37 All brands and logos are registered trademarks of their respective owners i EG PM2 LAN PROGRAMMABLE POWER energente OUTLET STRIP WHT LAN INTERFACE Figure 16 Device
33. e timer schedule will only be executed if the managing computer is on and the Power Manager is launched 48 All brands and logos are registered trademarks of their respective owners Nm 2 PROGRAMMABLE POWER rge OUTLET STRIP WITH LAN INTERFACE aget Figure 24 Switch time Switch OFF time Perform task every Comment 10 40 19 08 2010 20 38 19 08 2010 e To add a new task click the Add button The Add task window will appear see Figure 25 below 49 All brands and logos are registered trademarks of their respective owners H EG PM2 LAN PROGRAMMABLE POWER ene OUTLET STRIP WITH LAN INTERFACE Figure 25 r Task V Switch ON time 1041 13 08 2010 V Switch OFF time 2041 E 13 08 2010 El Perform task every 1 days v Comment WE Enabled Cancel In the Add task window check Switch ON time and or Switch OFF time checkboxes and specify the time to switch the socked on and or off If you want the same event to be performed periodically check Perform task every checkbox and specify the time interval You can also add remarks about the task in the Comment field To disable the task uncheck the Enabled checkbox and to enable the task again re check the checkbox 50 All brands and logos are registered trademarks of their respective owners N e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP
34. ff and you have the Switch On Switch Off button Besides you can see the scheduled events for this socket The socket number and its eventual name see section 4 4 below are shown at the very top of the page see Figure 7 below 21 All brands and logos are registered trademarks of their respective owners energenie EnerGenie Socket 1 Socket 2 Socket 3 Socket 4 Socket Settings Device Settings LAN Settings Log Out EG PM2 LAN PROGRAMMABLE POWER OUTLET STRIP WITH LAN INTERFACE Figure 7 Socket 1 FT Set schedule OFF Event schedule ON Tue Jul 10 2012 14 20 00 GMT 0200 W Europe Daylight Time Tue Jul 10 2012 14 30 15 GMT 0200 W Europe Daylight Time ON Mon Jul 09 2012 14 40 30 GMT 0200 W Europe Daylight Time Mon Jul 09 2012 14 50 45 GMT 0200 W Europe Daylight Time Periodic Periodic Loop period 1 days Synchronized Mon Jul 09 2012 12 37 00 GMT 0200 W Europe Daylight Time Mon Jul 09 2012 14 10 29 GMT 0200 W Europe Daylight Time The socket shown on the Figure 7 is currently off it will be turned on again automatically on the 9th of July at 14 40 30 and on the same day at 14 50 45 it will be switched off Next day it will be turned on at 14 20 00 and at 14 30 15 it will be switched off Last two events will be executed each day staring from the 10 of July 22 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE
35. gs LAN Settings Log Out Choose the date and time of the scheduled event If you wish the event to be executed periodically then choose Periodic option and set the loop period To commit to your changes press the Apply button To delete the entry press the x button To delete the entered schedule press the Clear schedule button 24 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE aet NOTE The hardware schedule keeps running even when the device is powered off However it is recommended not to power off the device for longer than 1 week because the built in battery might get discharged then In this case the internal clock of the device would be reset and as result some schedule events would not be executed Besides all the Sockets would lose their previous status they will be switched on Leave the device switched on for one day to fully charge the battery 4 4 Socket Name settings page On the Socket name settings page see Figure 9 below you can assign an applicable name to your sockets These names will be shown on EnerGenie page see section 4 2 above as well as on the Socket pages see section 4 3 above NOTE The socket names can not be longer than 11 characters HINT Call your socket by the device which is attached to this socket For example call Socket 1 TV set if your TV is connected to this socket 2
36. ice is an advanced standby killer Using this feature you can for example switch your scanner on off whenever Photoshop is started closed To add a new file event click the Add folder button see Figure 27 above The Add file event window will appear see Figure 29 below Figure 29 r Event Title Path name File name On placing Switch ON Bl Delay on placing On removal Switch OFF Delay on removal Enabled 55 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE Lo sms Specify the path to the folder you would like to monitor using the Browse button or typing it manually in the Path name field Specify the File name mask using wildcard characters Check then On placing and or On removal checkboxes and select the event and delay NOTE The On placing event will take place when the first file matching the specified file name mask is placed into the specified folder The On removal event will take place when the last file matching the specified file name mask is removed from the specified folder HINT Your device is an advanced standby killer Use the Add folder button to assign c system32 spool printers folder to switch your printer on whenever you start printing and to switch it off again whenever you are ready with printing H
37. ime correction to work properly the device should have access to the Internet and have a proper DNS server setting see section 4 5 above Server name can be convenient to identify the web server if you have more than one EG PM2 LAN It is Server 1 by default The password is necessary to access EG PM2 LAN both from your web browser and the Power Manager software see section 6 below This password is case sensitive and can be up to 32 characters long Alphanumeric characters and spaces are allowed to be entered Only the first eight characters of the password are used to access the device with the Power Manager software You will need to enter this password in the Add LAN device window see section 7 below The Power Manager software accesses EG PM2 LAN via a certain client port by default 5000 You can change this port to any other except port 80 which is always occupied by the web server 30 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE aget Don t forget to push the Apply button to save your settings 4 7 Web server logout Having finished working with EG PM2 LAN choose Log Out in the main menu If you don t do this you will be logged automatically after 10 minutes of inactivity While you are logged to the web server it can t be accessed from any other computer If another user tries to access the web server which
38. ing sockets see Figure 13 below Figure 13 energenie User John Device1 Log Off Socketi Socket2 Socket3 Socket4 gt Privacy gt Terms of use 2010 energenie com All rights reserved 33 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE aet This page will automatically update itself and will keep showing you the time when your device was last seen online the latest time when the device communicated with the server and the status of each socket Click your user name to change your account settings Click the device to change its name and or transfer it to another account Click the sockets to change their names Click the On Off buttons to switch the sockets on or off NOTE the switching command can only be properly executed if the device is switched on connected to the Internet and activated NOTE the Last seen online status information lets you check if the device keeps communicating with the server 34 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE aet 6 Power Manager software The Power Manager software is designed to support not only EG PM2 LAN but also other power management family products please visit www energenie com 6 1 Finding EG PM2 LAN To b
39. ion B then the following procedure is required to let EG PM2 LAN obtain a fixed IP address Turn EG PM2 LAN on with the Main rocker switch 2 Press IP Config C button on the side control panel see Figure 2 above with the tip of a pen While holding it pressed press and release Reset A button and wait for about 3 seconds until you hear the sockets switching twice The above mentioned procedure forces EG PM2 LAN to reset itself to the default settings see below IP 192 168 0 254 Subnet mask 255 255 255 0 Gateway 192 168 0 1 DNS 0 0 0 0 DHCP enabled IP filtering disabled Power Manager client port 5000 EG PM2 LAN then searches for an IP address from your eventual DHCP server If no DHCP server is found within 1 minute EG PM2 LAN will then automatically revert to the default settings see above with IP 192 168 0 254 13 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE at 3 3 Power Manager installation It is now time to identify which IP address has been obtained by EG PM2 LAN We need to carry out the following e Insert the Power Manager CD into a PC CD ROM drive This PC can be connected either to the same LAN where the device is if you chose option A section 3 2 or directly to the device with the crossover RJ 45 cable if you chose option B section 3 2 e If for any reason the autom
40. is running an active session the error message will be shown on the login page Somebody with another IP has already logged in Try again later In the meantime the Power Manager software see section 6 can still access the EG PM2 LAN 31 All brands and logos are registered trademarks of their respective owners H EG PM2 LAN PROGRAMMABLE POWER ene OUTLET STRIP WITH LAN INTERFACE 5 EnerGenie com device interface With your free personal account at EnerGenie com website you will be able to access your EG PM2 LAN from anywhere in the world using any Internet enabled device desktop PC laptop smartphone etc See section 4 2 above on how to register your EG PM2 LAN on the server and setup the connection 5 1 Logging in To login into your EnerGenie account just open the webpage www energenie com user in your Internet browser and enter your login and password in the login window see Figure 12 below Figure 12 energenie Login son Password m rere 32 All brands and logos are registered trademarks of their respective owners men H energente EG PM2 LAN PROGRAMMABLE POWER OUTLET STRIP WITH LAN INTERFACE Check Remember me checkbox for automatic login in the future the website will then save a cookie on your computer If you lost your password click Forgot password button 5 2 Device management page After a successful login you will see the list of your registered devices and their correspond
41. list in EG PM2 LAN hardware settings see section 4 5 above e EG PM2 LAN is not connected to local network To check if EG PM2 LAN is on your local network you can do so called ping test Go to Start gt Run e Type cmd e Type ping lt EG PM2 LAN IP Address specified in utility gt in the window which would appear Suppose EG PM2 LAN with IP address 192 168 2 189 is connected to the local network Then the cmd window will look as shown on the Figure 18 below 40 All brands and logos are registered trademarks of their respective owners EG PM2 LAN PROGRAMMABLE POWER e ne rgenie OUTLET STRIP WITH LAN INTERFACE Figure 18 6 8 6082 ft Corporation All rights reserved C Users Administrator gt ping 192 168 2 189 Pinging 192 168 2 189 with 32 bytes of data time ims TTL 128 time lt ims TTL 128 E time lt ims TTL 128 botes 32 time lt ims TTL 128 cs for 192 168 2 189 ent 4 Received 4 Lost loss Approximate round trip tim n milli seconds Minimum ms Maximum ims Average C Users Administrator gt e EG PM2 LAN is connected to local network ping test is ok but not responding Reset EG PM2 LAN by pressing the Reset button A on the side control panel see Figure 2 above or switch it off and then on again see Figure 1 above NOTE The Reset button A see Figure 2 above can sometimes help if EG PM2 LAN can t be accessed or works abnormally The device will then be restarted
42. mbird de support support gembird de Tel 49 180 5 436247 0 14 pro Minute aus dem deutschen Festnetz Mobilfunkpreise k nnen abweichen 63 All brands and logos are registered trademarks of their respective owners NR H energente EG PM2 LAN PROGRAMMABLE POWER OUTLET STRIP WITH LAN INTERFACE GARANTIE VOORWAARDEN CONDITIONS DE GARANTIE Garantie est de 24 mois a partir de la date d achat de De garantietermijn bedraagt 24 maanden en gaat in op de aankoopdatum van het product door de eindgebruiker Op de aankoopbon moeten de aankoopdatum en productomschrijving duidelijk vermeld staan Gelieve de aankoopbon de gehele garantieperiode te bewaren deze is ten alle tijden benodigd voor alle garantie aanspraken Tijdens de garantieperiode zullen alle gebreken verholpen of vervangen worden door de fabrikant d m v reparatie omruiling van het defecte onderdeel of het gehele apparaat Aanspraken tijdens de garantieperiode leiden niet tot verlenging hiervan Garantieaanspraak vervalt bij schade of gebreken die ontstaan zijn door oneigenlijk gebruik misbruik of invloeden van buitenaf vallen stoten water stof vuil of breken Slijtagegevoelige onderdelen b v batterijen zijn uitgesloten van garantie Bij ontvangst van de RMA goederen behoudt Gembird zich het recht om te kiezen tussen vervanging van de defecte waren of het uitgeven van een kreditnota Het bedrag van de kreditnota zal altijd gecalculeerd zijn op basis van
43. oduct and producten fit par Y 20 and 21 of the Product Safe law TOV Rheinland LGA Products GmbH Tillystrafie 2 90431 N rnberg Tel 492118 06 13 71 email cercle tov com Fax 06 39 35 open mv comte Dipl ng W Feuker Ausstellungsdatum Date of Issue 16 11 2012 day mo yr EG PM2 LAN PROGRAMMABLE POWER OUTLET STRIP WITH LAN INTERFACE CERTIFICATE k B T VRheinland of Conformity Low Voltage Directive 2006 95 EC Registration AN 50241342 0001 Report 17014557 001 Holder GEMBIRD ELECTRONICS LTD Flat RM 2103 21 F Office Tower Langham Place 8 Argyle Street Mongkok Hong Kong Product Multiplo Socket Outlets Portable Socket outlet Identification EG PM2 LAN _ EG PM2 Serial No n a Remark ued in conjunction with above T V Rheinland license S1 50187883 0001 This certificate of conformity is based on an evaluation of a sample of the above mentioned product Technical Report and documentation are at the Licence Holdor s disposal This is to certify that the tested sample is in conformity with all revision of Annex 1 of Council Directive 2006 95 EC in its latest amended version referred to as the Low Voltage Directive This certificate does not imply assessment of the series production of the product and does not permit the use of a Rheinland mark of conf the EC declaration of conformity according to Annex III of the Directive Certification Body Date
44. ort ort gmb nl 33 0 251 404849 Prix d appel depuis telephone fixe Pays Bas 0 15 euro min Prix d appel depuis telephone mobile autre pays selon operateur Exclusief mobiele telefoonkosten 64 All brands and logos are registered trademarks of their respective owners H energente EG PM2 LAN PROGRAMMABLE POWER OUTLET STRIP WITH LAN INTERFACE EE 1 2 3
45. s Help O 2206 Pe 2 2 Address 5 http 192 168 2 10fenergenie html Server 1 Socket 1 Socket 2 Socket 3 Socket 4 ON OFF ON OFF ON OFF ON OFF rgenie Your EnerGenie account Deactivate Register EnerGenie Register to manage EG PMS LAN from Internet free service Socket 1 Status Activated Trying to connect Socket 2 Socket 3 Socket 4 Socket Name Settings Device Settings LAN Settings 20 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE aet After a successful registration and activation the button Register will be renamed to Login and will then open the Login page of EnerGenie com and the button Activate will turn into Deactivate If by any reason you would eventually decide to stop managing your EG PM2 LAN from Internet use then Deactivate button to stop communication of the device with EnerGenie com server If you eventually decide to change registration of your EG PM2 LAN and assign it to another account it will be possible via EnerGenie com website see section 5 below See section 5 below for further details on managing your EG PM2 LAN via EnerGenie com website 4 3 Socket page There are 4 manageable sockets on EG PM2 LAN and so there are 4 pages corresponding to them On each status page you can see the socket status on or o
46. timer schedule hardware schedule and then disconnect EG PM2 LAN from LAN and use it elsewhere The device can be used as an advanced standby killer With your free personal user account at EnerGenie com you can manage your EG PM2 LAN via the Internet from all over the world even from your Smartphone 1 1 Features e Switch individual sockets on off manually from your computer e Switch individual sockets on off by a programmable timer schedule e Switch individual sockets on off whenever a certain software event occurs e g Windows other software start up shutdown print spooler starting and finishing its job etc e Because of the LAN interface and the built in web server EG PM2 LAN can be accessed from any computer within your local network via an Internet browser or Power manager software All brands and logos are registered trademarks of their respective owners EG PM2 LAN PROGRAMMABLE POWER OUTLET STRIP WITH LAN INTERFACE is also possible to assign an external IP address to EG PM2 LAN to enable worldwide remote access via the Internet No external IP address at home No problem Create your own user account on EnerGenie com to manage your EG PM2 LAN via Internet with any PC or smartphone Switching on your coffee maker before setting off for home becomes a reality IP filter 64 bit password protected data encryption guarantees secure Internet access to EG PM2 LAN EG PM2 LAN has a built in battery
47. y Login page will then be displayed see Figure 5 below NOTE Java script must be enabled in your Internet Explorer or another browser settings Otherwise you get an error message WARNING JAVASCRIPT IS DISABLED Figure 5 EnerGenie Web Server 1 Password The default password is 1 It is recommended to change the password on the Device settings page see section 4 6 below after the first login 17 All brands and logos are registered trademarks of their respective owners e EG PM2 LAN PROGRAMMABLE POWER e ne rge nie OUTLET STRIP WITH LAN INTERFACE aset After a successful login you will face the Socket 1 Status page see section 4 2 below NOTE There is a possibility that you might then need to open the LAN settings page see section 4 5 below to complete the IP configuration 4 2 EnerGenie page With the help of EnerGenie page see Figure 6 below you will be able to see the status of all your four manageable sockets and to Switch the sockets on and off manually The status of your sockets as well as the buttons to switch them on off are located at the top of the page NOTE the names of the sockets can be changed from the default Socket1 Socket2 Socket3 Socket4 to something meaningful on the page Socket Name Settings see section 4 4 below The EnerGenie page also allows you to setup access and management switch on and off of your EG PM2 LAN from anywhere via Internet even if it does not have an extern
Download Pdf Manuals
Related Search