EK Water Blocks 3831109840597
Contents
1. Installation and mounting manual for EK BAY DCP 2 2 Combo Reservoir This product is intended for installation only by expert users Please consult with a qualified technician for installation Improper installation may result in damage to your equipment EK Water Blocks assumes no liability whatsoever expressed or implied for the use of these products nor their installation The following instructions are subject to change without notice Please visit our web site at www ekwb com for updates Before installation of this product please read important notice disclosure and warranty conditions printed on the back of the box Before you start using this product please follow these basic guidelines 1 Please carefully read the manual before through before beginning with the installation process 2 The EK High Flow and EK PSC type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o ring gaskets 3 The use of quality market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system Take your reservoir out of the original packaging and place it on a flat clean surface with the front facing downwards Proceed with the following steps 1 Remove the three out of four original EK DCP 2 2 pump screws from the pump using Philips head screwdriver 2 Install o ring OR 20x2 gasket into the groove milled in EK BAY DCP 2 2 Co2. mbo Reservoir acetal body Make sure the gasket is positioned correctly in the groove 3 Place the pump onto the main reservoir body and insert the three 3 M3x18 DIN7984 screws which are provided with the reservoir EK recommends user to screw in the screws slightly using your thumbs for the screws prior to tightening them with the enclosed 2mm Allen key 4 Tighten the screws using 2mm Allen Key ELLET EK BAY DCP 2 2 Combo Reservoir K Allen key 2mm STEP 1 Remove the marked screws Screw M3x18 DIN7984 EK DCP 2 2 water pump OR 20x2 gasket This reservoir occupies two 5 25 drive bay expansion slots in your computer chassis Free two slots in case they are already occupied with other computer components such as optical or hard disk drives 1 Install anti vibration rubber damper into each of the three slots on the sides of the reservoir 2 Place the reservoir in your 5 25 drive bay with the front plate facing outwards 3 Secure the reservoir to the drive bay cage using the enclosed M3x4 DIN7985 screws and Philip head screwdriver M3 BAY anti vibration rubber damper Revision 1 0 Released on 2 of October 2012 Connect two G1 4 threaded fittings to the reservoir IN and pump OUT Please note the water flow orientation EKWB recommends using EK PSC fittings with the EK BAY DCP 2 2 Combo Reservoir series reservoirs To ensure that the tubes are securely attached to the barb fittings please use hose clamps
3. o provide the most comprehensive tutorial possible EK Water Blocks assumes no liability expressed or implied for any consequential damage s occurring to your equipment as a result of using EK Water Blocks cooling products either due to errors or omissions on our part in the above instructions or due to failure or defect in the EK Water Blocks cooling products WARRANTY Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final user During this period products will be repaired or have parts replaced at our discretion provided that I the product is returned to the agent from whom it was purchased IT the product has been purchased by an end user and has not used for commercial purposes III the product has not been misused handled carelessly or used in a manner other than in accordance with the instructions provided describing its installation and proper use This warranty does not confer rights other than those expressly set out above and does not cover any claims for consequential loss or damage This warranty is offered as an extra benefit and does not affect your statutory rights as a consumer This warranty is voided if the product comes in contact with aggressive UV additives or other improper liquids REQUIRED TOOLS Revision 1 0 Released on 2 of October 2012
4. or an appropriate substitute Predrilled holes for 5mm LEDs acrylic version only EK DCP 2 2 Water Pump Water out to radiator or water block NE Inlet G1 4 eee Cr ee Tr Tere a T tog a F threaded port Water In from radiator or water block gt EK PSC fitting Fill reservoir through G3 8 threaded fill port marked with arrow and make sure liquid is not spilled over your computer or any electrical devices nearby Preferably your pump s height level should be lower than that of the EK BAY RES Single reservoir in order to flood and prime the water pump Run your pump Shortly for couple of times to make sure water floods your tubes and other water cooling components Repeat the procedure until you are done and pay attention to the water level in your reservoir Lowest and highest recommendable water levels are indicated on the reservoir s front panel m min max Once done with the filling process please close your EK BAY DCP 2 2 Combo Reservoir with G3 8 plug and tighten the seal using enclosed Allen key VERY IMPORTANT NOTICE Once the installation is completed it is a recommended practice to test the cooling circuit for leaks prior to powering up the computer We recommend a 24 hour leak test prior to powering up the computer Do not test the water block using tap water pressure This will rupture the top of the housing and render the block unusable and will void your warranty While all efforts have been made t
Download Pdf Manuals
Related Search