DeLonghi Icona Vintage ECOV310.GR
Contents
1. Check that the holes are not blocked If this is not the case clean them using a pin fig 24 e Rinse the outlet under the tap rubbing continu ously e Re mount the boiler outlet paying attention to po sition it correctly on the gasket The warranty is not valid if the cleaning operations de scribed above are not performed on a regular basis Other cleaning operations 1 Do not use solvents or abrasive detergents to clean the machine Use a soft damp cloth 2 Clean the filter holder cup the filters drip tray and water tank regularly To empty the drip tray remove the cup warmer grid remove the water and clean the tray using a cloth then re assemble the drip tray Clean the water tank using a soft bottle brush in order to reach the bottom AN Danger During cleaning never immerse the ma chine in water it is an electric appliance DESCALING It is recommended to descale the machine about every 200 coffees It is recommended to use De Longhi descaler that can be found on the market Follow this procedure 1 Fill the tank with the descaling solution obtained by diluting the descaler with water on the basis of the indications given on the pack 2 Press the on off button and wait for the OK light to switch on 3 Make sure that the filter holder is not attached and position a container under the machine outlet 4 Press the coffee button and allow about 1 4 of the solution contained in the tank flow ou2. HOW TO MAKE CAPPUCCINO nm Prepare the espresso coffee as described in the previous paragraphs using cups that are large enough Press the steam button fig 15 In the meantime fill a container with about 100 grams of milk for every cappuccino to be prepared The milk must be at refrigerator temperature not hot When choosing the container considers that the volume of the milk will increase by 2 or 3 times Or Bene it is recommended to use semi skimmed milk at refrigerator temperature 5 C Position the container with the milk under the cap puccino maker Wait for the indicator light relative to the steam but ton to switch on fig 16 This indicates that the boiler has reached the ideal temperature for the production of steam Open the steam tap for a few seconds to remove any water present in the circuit Close the tap Dip the cappuccino maker into the milk for few mil limeters fig 17 making sure not to immerse the raised line on the cappuccino maker indicated by the arrow in fig 17 Turn the knob anti clockwise fig 18 for at least half a turn Steam escapes from the cappuccino maker giving the milk a creamy appearance and increasing its volume To obtain a creamier froth dip the cappuccino maker into the milk and turn the container with slow movements from the bottom upwards When the volume of the milk has doubled dip the cappuccino maker deep down and continue to heat the milk When the d
3. hazard To prevent sprays do not re lease the filter holder while the machine is dis pensing coffee To remove the used coffee lock the filter using the lever in the grip and let the coffee fall out by knock ing the over turned filter holder fig 13 Turn the machine off by pressing the on off button fig 4 Before using the machine for the first time all accesso ries and internal circuits must be washed by making at least five cups of coffee without using ground coffee HOW TO PREPARE THE ESPRESSO USING PODS i Pre heat the machine as described in the PRE HEATING THE COFFEE MACHINE chapter making sure that the filter holder is attached to the ma chine Hotter coffee is obtained in this way Nota Bene use pods that comply with the ESE Standard this will be indicated on the packaging by the following mark The ESE Standard is a system accepted by the leading coffee pod manufacturers and allows espresso coffee to be made simply and without making a mess Place the small filter in the filter holder making sure that the projection is correctly inserted into the relative seat as indicated in fig 8 Insert the pod centring it as far as possible on the filter fig 14 Always follow the instructions of the pod pack for correct positioning of the pod on the filter Attach the filter holder to the machine turning it fully home fig 5 Proceed as in points 5 6 and 7 in the previous paragraph
4. of the ground coffee powder The milk does not froth when ma king a Cappuccino The milk is not cold enough e Always use milk at refrigerator temperature e The cappuccino maker is dirty e Carefully clean the holes in the cappuccino maker in particular those indicated in figure 21 17
5. INTRODUCTION Thank you for having chosen our coffee machine We hope you have fun with your new appliance Take a few minutes to read these instructions This is the only way to avoid danger and damage to the machine Symbols used in these instructions The important recommendations have these symbols These recommendations must be followed N paner Failure to comply can be or is the cause of injury due to life threatening electric shocks An Failure to comply can be or is cause of injury or damage to the appliance Scalding hazard Failure to comply can be or is the cause of scalding or burns Nota Bene This symbol highlights recommenda tions and important information for the user SAFETY Fundamental recommendations regarding safety Danger As the appliance operates using electric current electric shocks can not be excluded Therefore follow the safety recommendations given e Do not touch the appliance when you have wet hands or feet e Do not touch the plug with wet hands e Make sure that the socket used can always be eas ily reached so that the plug can be removed when required e Remove the plug from the socket by acting directly on the plug itself Do not pull the cable as damage could be caused e Remove the plug from the socket to disconnect the appliance completely e Do not attempt to repair the appliance if it should breakdown Switch the appliance off remove the plug from the socket an
6. are two cups of coffee fill the filter with two less than level measuring spoons of ground coffee about 6 6 gr Fill the filter with small amounts at a time to prevent the coffee spill ing out Ti aise for correct use before filling the filter with ground coffee always make sure there is no residual coffee in the filter from the previous infu sion 3 Distribute the ground coffee evenly and press it lightly using the coffee tamper fig 10 Pressing the ground coffee is very important to ob tain a good espresso If you press too hard the cof fee will run out slowly and the cream will be dark If you press too lightly the coffee will run out too fast and the cream will be very light Remove any excess coffee from the rim of the filter holder and attach it to the machine turn the grip to the right fig 5 to prevent water from escaping Position the cup or cups under the filter holder spouts fig 11 It is recommended to warm the cups before making the coffee by running them un der hot water or leaving them to pre heat on the cup warmer for at least 15 20 minutes fig 12 Make sure that the OK light fig 6 is on if it is off wait for it to switch on and press the coffee button fig 7 Once the desired amount of coffee has been obtained press the same button again fig 7 It is recommended not to run the coffee for more than 45 seconds Turn the grip from right to left to release the filter holder Scalding
7. d contact the After Sales Service e Ifthe plug or power supply cable are damaged have them replaced exclusively by the De Longhi After Sales Service in order to prevent risks Ti iste Keep the packaging material plastic bags expanded polystyrene out of the reach of children AN Attention The appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance AN Scalding hazard This appliance produces hot water and steam may form when it is operating Pay attention not to come into contact with hot water sprays or steam Do not touch the cup warmer plate when the ap pliance is on it is hot Use in compliance with destination This appliance is manufactured for the preparation of coffee and to heat beverages The appliance is designed and produced for domestic use only It is not suitable for use in Staff kitchens in shops offices and other workplaces farm houses hotels motels or other holiday accommodation guest houses Any other use must be considered improper and there fore dangerous The manufacturer is not liable for damage deriving from the improper use of the appliance Instructions for use Rea
8. d these instructions carefully before using the ap pliances Failure to comply with these instructions can lead to injury and damage to the machine The manufacturer is not liable for damage deriving from the failure to comply with the user instruc tions Nota Bene Keep these instructions carefully If the appliance should be transferred to other per sons these instructions must accompany it DESCRIPTION Control panel Steam knob Water tank Water tank lid Power supply cable Steam or hot water tube Cup tray Drip tray Cappuccino maker Nozzle Boiler outlet Coffee tamper Measure for ground coffee CONAN RWON 4 14 Filter holder 15 Large filter 2 doses 7 16 Small 1 dose filter or for pods 17 Steam function selection button 18 Coffee or hot water tube 19 On off button 20 On indicator light 21 OK indicator light 22 Steam function selected indicator light 23 Cup warmer plate PRELIMINARY OPERATIONS Check after transport After the packaging has been removed check the in tegrity of the appliance and the presence of all acces sories Do not use the appliance in the presence of obvious damage Contact the De Longhi After Sales Service Installing the appliance The following safety measures must be complied with when installing the appliance e The appliance could be damaged by the penetration of water Do not position the appliance near to water taps or sinks e The appliance co
9. e bottom CO vote Bene it is normal to find water in the compartment under the tank dry using a clean sponge Pre heating the coffee machine It is advised to pre heat the coffee machine as follows in order to obtain an espresso coffee at the right tem perature 1 Press the ON OFF button the relative indicator light switches on fig 4 and attach the empty filter holder to the machine fig 5 2 Place a cup under the filter holder Use the same cup in which the coffee is to be served so that it can be pre heated 3 Wait until the OK light comes on fig 6 and then press the coffee button straight away fig 7 Allow the water to run until the OK light switches off and then stop the water by pressing the coffee button again fig 7 4 Empty the cup wait for the OK light to switch on again and repeat the same operation again It is normal for a small harmless puff of steam to be released when the filter holder is removed HOW TO PREPARE THE ESPRESSO USING 1 After having pre heated the machine as described in the previous paragraph insert the ground cof fee filter into the filter holder making sure that the projection is correctly inserted into the relative seat as indicated in fig 8 Use the smallest filter for one coffee or the larger one to make two cups of cof fee 2 To prepare one coffee fill the filter with a level measuring spoon of ground coffee about 7gr fig 9 If you wish to prep
10. e hand to hold the cappuccino tube and the other to release the cappuccino maker by turning it clockwise and pulling it downwards fig 19 3 Remove the steam nozzle from the tube by pulling it downwards fig 20 4 Wash the cappuccino maker and steam nozzle thor oughly in warm water 5 Make sure that the two holes indicated by the ar rows in fig 21 are not blocked Clean using a pin if necessary 6 Re mount the steam nozzle by inserting it firmly upwards into the steam tube 7 Re mount the cappuccino maker by inserting it up wards and turning it anti clockwise PRODUCTION OF HOT WATER 1 Switch the machine on by pressing the on off but ton fig 4 Wait for the OK light to switch on fig 6 Position a container under the cappuccino maker 3 Press the coffee button fig 7 and turn the steam knob anti clockwise at the same time fig 18 the hot water will escape from the cappuccino maker 4 To interrupt the hot water turn the steam knob clockwise and press the coffee button again fig 7 Maximum delivery of 60 seconds is recommend ed CLEANING A N Danger Before performing any cleaning opera tions of the external parts of the appliance switch the machine off remove the plug from the socket and let the machine cool down Cleaning and maintenance of the filter Clean the filter holder and ground coffee filters about every 300 coffees and however when the coffee drips through the filt
11. er holder and does not flow completely e Remove the filter from the filter holder e Unscrew the filter cap fig 22 in the direction indi cated by the arrow on the cap itself e Slide the cream enhancer device from the container by pushing it from the cap end e Remove the gasket e Rinse all components and clean the metal filter thor oughly using hot water and a brush fig 23 Check that the holes in the metal filter are not blocked If this is not the case clean them using a pin see fig 24 e Re mount the filter and the gasket on the plastic disc as indicated in figure 25 Make sure that the plastic disc pin is inserted inside the hole in the gasket as indicated by the arrow in fig 25 e Re insert the unit obtained into the steel container for the filter fig 26 making sure that the pin is in serted into the hole of the support itself see arrow fig 26 e Finally tighten the tap The warranty is not valid if the cleaning operations de scribed above are not performed on a regular basis Cleaning the boiler outlet About every 300 coffees the espresso boiler outlet must be cleaned as follows e Make sure that the coffee machine is not hot and the plug is disconnected from the socket e Use a screwdriver to remove the screw that fixes the espresso boiler outlet fig 27 e Remove the boiler outlet e Clean the boiler using a damp cloth fig 27 10 e Clean the outlet thoroughly using hot water and a brush
12. esired temperature ideal val ue is 60 C and the desired milk froth have been reached interrupt the steam by turning the steam knob clockwise and release the steam button Use the on off button to switch the machine off fig 4 The relative on light switches off Pour the frothed milk into the cups containing the previously prepared espresso coffee The cappuc cino is ready add sugar at will and if desired sprin kle a little powdered chocolate on top of the froth i Nota Bene e if more than one cappuccino is to be prepared first make all of the coffees and then prepare the milk for all of the cappuccinos e if more coffee must be prepared after the milk has been frothed allow the boiler to cool first otherwise the coffee will be burned To cool it position a container under the filter holder spouts fig 11 press the steam button and allow water to run out until the steam function light switches off then prepare the coffee Maximum steam delivery of 60 seconds is recom mended and the milk must not be frothed more than 3 times consecutively JN niente cappuccino maker must always be washed after use to ensure hygiene Proceed as follows 1 Discharge a small amount of steam for a few sec onds see points 2 5 and 6 of the previous para graph by turning the steam knob fig 18 By do ing this the cappuccino maker empties any milk left inside Switch the machine off by pressing the ON OFF button 2 Use on
13. nce with the fol C lowing CE Directives e Low voltage Directive 2006 95 CE and succes sive amendments e EMC Directive EMC 2004 108 CE and successive amendments e The materials and objects destined to come into contact with food stuffs are in compliance with the provisions of the 1935 2004 European Standard PROBLEM POSSIBLE CAUSES SOLUTION Espresso coffee does not flow out No water in the tank e Fill the water tank e The holes in the filter holder are blocked e Clean the holes in the filter holder spouts he espresso boiler outlet is blocked e Clean as indicated in the Cleaning the boiler outlet paragraph Espresso coffee drips from the ed ges of the filter holder instead of through the holes The filter holder is inserted incorrectly e Attach the filter holder correctly and turn it fully home firmly e The espresso boiler gasket has lost elasticity e Replace the espresso boiler gasket at an After Sales Centre e The holes in the filter holder spout are blocked e Clean the holes in the spouts The espresso coffee is cold he espresso OK light is not on when the coffee button is pressed e Wait for the OK light to switch on e Pre heating has not been carried out e Pre heat as indicated in the paragraph e The cups have not been pre heated e Pre heat the cups using hot water or leaving them for at leas
14. t every now and again turn the steam knob and allow a small amount of solution to escape then interrupt by pressing the button again and leave the solution to act for about 5 minutes 5 Repeat point 4 another 3 times until the tank is completely empty 6 To eliminate residues of the solution and lime scale rinse the tank well and fill it with clean water with out descaler 7 Press the coffee button fig 6 and operate the ap pliance until the tank is completely empty 8 Repeat operations 6 and 7 again Recommendations for the correct disposal of the prod uct in compliance with the 2002 96 CE European Direc tive The product must not be disposed of as urban Bef se at the end of its working life It must be taken to appropriate local authority EE Separate waste collection centres or to dealers providing this service Disposing of a household appliance separately avoids possible negative consequences for the environment and health deriving from unsuitable disposal and allows to recover the materials of which it is made in order to make significant savings in energy and resources The product has the crossed out wheeled bin mark as a reminder of the obligation to dispose of household appliances separately TECHNICAL DATA Mains voltage 220 240V 50 60Hz Absorbed power 1100W Pressure 15 bar Water tank capacity 1 4 litres Dimensions LxHxD 255x315x280 395 mm Weight 3 9 kg The appliance is in complia
15. t 20 minutes on the cup warmer plate on the lid Loud pump noise e The water tank is empty e Fill the water tank e The tank is inserted incorrectly and the valve on the bottom is not open e Press the tank lightly to open the valve on the bottom The coffee cream is clear it flows quickly from the spout The ground coffee has not been sufficiently pressed e Tamper the ground coffee more fig 10 e Not enough ground coffee e Increase the amount of ground coffee e The coffee is not ground finely enough e Only use coffee ground specifically for espresso coffee machines ncorrect type of ground coffee e Change the quality of the ground coffee The coffee cream is dark it flows slowly from the spout The ground coffee is too tightly pressed e Tamper the coffee less fig 6 e Too much ground coffee e Decrease the amount of ground coffee he espresso boiler outlet is blocked e Clean as indicated in the Cleaning the espresso boiler outlet chapter e The filter is blocked e Clean as indicated in the cleaning the filter par e The coffee is too finely ground e Only use coffee ground specifically for espresso coffee machines he ground coffee is too fine or is damp e Only use coffee ground specifically for espresso coffee machines and it must not be too damp ncorrect type of ground coffee e Change the quality
16. uld be damaged if the water it contains freezes Do not install the appliance in a room where the temperature can fall below freezing point e Position the power supply cable in a way that it can not be damaged by sharp edges or by contact with hot surfaces e g electric plates Connecting the appliance AN attention Make sure that the electric mains volt age corresponds with that indicated on the data plate on the base of the appliance e Only connect the appliance to correctly installed socket with minimum rating of 10A and efficient earthing e In the case of incompatibility between the socket and the plug on the appliance have the plug re placed by a qualified technician e The power supply cable on this appliance must never be replaced by the user as special tools are needed for this operation Contact an After Sales Centre authorised by the manufacture if the cable is damaged or must be replaced in order to avoid all risks Filling the water tank 1 Open the water tank lid fig 1 and then lift the tank to remove it fig 2 2 Fill the tank with fresh water but do not pass MAX fig 3 Re position the tank by pressing it lightly in a way to open the valve situated on the base of the tank itself 3 Even easier do not remove the tank just fill it by pouring in water from a jug Attention do not operate the appliance without water in the tank and always fill it when the water is a few centimetres from th
Download Pdf Manuals
Related Search