Chief LPAUB
Contents
1. See Figure 7 NI Figure 9 11 Optional Use padlocks not provided to secure uprights to head assembly See Figure 9 Figure 7 Installation Instructions LPAU Cable Management 1 Use two 1 4 20 x 1 2 Phillips pan machine screws Q to attach two cable hooks K to bottom of column assembly F See Figure 10 gt Des Se K x2 A Q x2 Figure 10 i 2 Route cables from display through front channel of column assembly See Figure 11 cable example front channel W i Kl A Figure 11 3 Route cables down column channel tucking them behind height adjustment carriage and underneath bracket holding height adjustment shaft See Figure 12 4 Wrap cables around cable hooks hooks as desired See Figure 12 5 Snap back cover G onto back of column assembly making sure cables fit through opening at bottom of cover See Figure 12 rear view o under bracket N cable opening Figure 12 LPAU Installation Instructions Adjustments Height Adjustment 1 Remove cable cover G to expose height adjustment knob 2 Turn heig2. located between the LPAU up to and including the display does not exceed 200 Ibs 90 7 kg 1 Lay display face down on protective surface CAUTION Using screws of improper diameter may damage your display Proper screws will easily thread into display mounting holes 2 Select screw diameter by examining hardware TA TK 4mm 5mm 6mm or 8mm and comparing with mounting holes on display See Figure 5 3 Select spacers See Figure 5 f mounting holes are not recessed and both uprights B can lay flat against display then no spacers are required f mounting holes are recessed or if protrusions prevent uprights B from laying flat then spacers TL or TM must be used 4 NOTE CAUTION Using screws of improper length may damage your display Proper screws will have adequate thread engagement without contacting bottom of display mounting holes Select screw length See Figure 5 Using your hand insert SHORTEST length screw of selected diameter TA TD TG or TI through universal washer TN uprights B selected spacer TL or TM into display mounting hole Do NOT thread screw into hole at this time Universal washers TN are not needed if using M8 button head cap screws TI TJ or TK Proper screw length requires base of screw head to protrude above flat washer a distance equal to or greater than the screw diameter If screw length is inadequate select longer screw Select shortest sc
3. A i i I 15 15 e a uta I i do di i i f H B seri Mali b d i 11193 m il MAL REG RTI il CENTER OE DISPLAY LPAU Installation Instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con lapiz Stiftmarkierung Marcar com lapis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte St
4. INSTALLATION INSTRUCTIONS Height Adjustable Video Cart S CHIEF LPAU Our Mounts Your LPAU Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is
5. allation Instructions LPAU 11 LPAU Installation Instructions G CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8800 002209 Rev00 2012 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 09 12 USA International Europe Asia Pacific p TI U gt TI U gt TU 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 SCH at n O 1 Yr consume
6. eeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a mao A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option J A CW vw CY Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabeca sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale O 09 CG Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguranga Chiave di sicurezza Veiligheidssleutel Cl de s curit Installation Instructions LPAU TOOLS REQUIRED FOR INSTALLATION M5 included 3 16 included T 1 4 hardware bag Cae Z A 4 l column upper P v e upright cover cover TA 8 TB 6 TC 6 2 M4x16mm M4x20mm M4x25mm interface upright D 1 column inner e e e cover TD 6 Meam TF 6 x20mm G ay M5x16mm M5x25mm back cover va F 1 e e interface head assembly column assembly TG 6 TH 6 M6x16mm M6x25mm LL a right cart leg K 2 Z cable hook TI 6 TJ 6 TK 4 H 1 M8x20mm M8x30mm M8x50mm left cart leg 9 TL 8 TM 8 mum TPO b ez L 1 left t
7. ht adjustment knob clockwise to raise display See Figure 13 3 Turn height adjustment knob counterclockwise to lower display See Figure 13 WARNING Do not attempt to raise or lower the adjustment carriage beyond its upper or lower limit High and low points are shown in Figures 12 and 13 NOTE A 1 2 socket wrench may also be used to adjust height by turning bolt just above height adjustment knob 4 Reinstall cable cover G to column assembly height adjustment knob 0 high e Figure 13 low point Figure 14 10 Pitch Adjustment 5 Turm pitch adjustment knob clockwise to tilt display forward See Figure 15 6 Turn pitch adjustment knob counterclockwise to tilt display back See Figure 15 Roll Adjustment 7 Turm roll adjustment knob clockwise to adjust roll to the left See Figure 15 8 Turn roll adjustment knob counterclockwise to adjust roll to the right See Figure 15 pitch adjustment knob Figure 15 Inst
8. ransition cover right transition cover 1 4 12 universal M5 N 5 Q 2 i RALE 516 18x3 3 4 OM 9 16 LPAU Installation Instructions Assembly And Installation Cart Assembly o Ji men 1 Place left and right transition covers L and M on corresponding cart legs H and J lining up the holes on the covers with the holes on the legs See Figure 1 side view right leg and cover shown e V L and M M M H and J C Fj Figure 1 2 Use four 5 16 18 x 3 3 4 button head cap screws P to Figure 3 secure legs H and J and covers L and M to column assembly F See Figure 2 4 Useremaining 5 16 18 x 3 4 button head cap screw N to secure column upper cover C to interface head assembly E See Figure 4 5 Snap column inner cover D onto column assembly F See Figure 4 rear view Figure 2 3 Use four 5 16 18 x 3 4 button head cap screws N to secure interface head assembly E to column assembly F See Figure 3 Figure 4 Installation Instructions LPAU Display Installation WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components
9. rew which will protrude the required distance Place uprights B on display ensuring See Figure 5 Center of uprights B are as close to the center of the back of display as possible after being installed Center of bracket is indicated by the diamond shaped hole Use selected screws and spacers to install two interface uprights B to back of display See Figure 5 Q YY TA TH Be AE Figure 5 LPAU Installation Instructions 9 Move latches on interface uprights to the closed position to secure display to head assembly See Figure 8 WARNING Display may be very heavy Ensure display may be safely lifted and maneuvered as required to install on cart Failure to take adequate precautions can result in 7 serious personal injury or damage to equipment 7 Position latches on interface uprights so that they are in the open position See Figure 6 8 Hang interface uprights B on interface head assembly E See Figure 6 open position Figure 8 10 Snap four upright covers A onto uprights See Figure 9 NOTE Tabs on inside of covers A will snap directly into holes on uprights to ensure a secure connection Figure 6 IMPORTANT In order to ensure an even mount install uprights to be centered over column assembly Do NOT install both uprights to the same side of column assembly
10. the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located between the LPAU up to and including the display does not exceed 200 Ibs 90 7 kg WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors WARNING RISK OF INJURY TO PERSONS Do not place video equipment such as televisions or computer monitors on cart legs SAVE THESE INSTRUCTIONS Installation Instructions LPAU DIMENSIONS CAHLE CORD WRAP HOOKS 5 TILT AD USTHENT 141 200 M H EI 31 50 EO A
Download Pdf Manuals
Related Search