Exposure 2010s2
Contents
1. This is best carried out by your dealer However if you wish to attempt installation yourself Seo LENS Switch off the unit 5 Remove the small jumper board that Is fitted on the right hand side at the back FUSE 120 Taa BOGA Taa 2 Remove the mains lead from the wall and the IEC socket on the phono module and carefully plug it in ensuring that all of the 4 Slide the cover back about 2 cm until it is free to move upwards to reveal the main circuit board 3 Remove the four cover screws 8 Replace the cover and screws 7 Push the three plastic mounting pillars into the corresponding holes in the main board pins are inserted correctly into their connectors Safety Incorrect installation or inappropriate use of the Exposure 2010S2 Integrated Amplifier may result in injury due to electric shock e Ensure that the voltage rating on the rear panel of this unit matches that of your local mains supply e Ensure that the mains cable and plug supplied with this unit is also correct Contact your dealer immediately if this is not the case e This unit is protected by a mains fuse which is accessible as part of the IEC socket on the rear panel Fuse replacement specifications 220 240V units TSA ace 10 120V units TSA Ue e Protect unit against all forms of liquid Never expose unit to dripping or splashing or place objects filled with water such as vases on the unit e Unplug uni2. and is not transferable When making claims under this warranty The equipment should be suitably packed and returned to the dealer from whom it was purchased or directly to the local distributor together with proof of purchase or a copy of the dated sales receipt If necessary the unit should be sent carriage pre paid by a reputable carrier NOT by post No responsibility is accepted for the unit whilst in transit to the dealer or agent and customers are advised to insure the unit against loss or damage whilst in transit The warranty card MUST be produced when making claims against this guarantee Any tampering or alteration made to the warranty card or to the serial number on the equipment will invalidate the warranty The dealer or the agent shall notify the customer when the repairs have been completed Ihe customer must claim the goods within fourteen days from the date of notice failing which the Company reserves the right to impose storage charges The Company reserves the right to dispose of the equipment after 90 days from the date of notice in a manner that It sees fit without compensation to the customer
3. igh fidelity engineering f Installation 4 Operation since 1974 The Exposure 2010S2 Integrated Amplifier Front View a Turn amplifier volume control to minimum Ce OLE EMO LUE b Press power switch The LED power indicator will light up The pre amplifier output relay will b Connect the mains c Connect to the mains click after a 6 second delay together with the cable to the IEC phie other indicator lights on Volume and Input outlet on the wall mains input socket DO NOT switch on selector Knobs until all input and output connections are made a Turn volume control to minimum before connecting or disconnecting any cables FUSE 00 120 UOHI Taa Danesti ET c Without playing any CD Tape DVD etc turn the volume control knob slowly clockwise to around 20 It is normal to hear a faint hiss 2 CD Player Tuner Tape DVD etc Connections The Exposure 2010S2 Integrated Amplifier is fitted with six line level RCA Phono inputs suitable for connection of CD players tuners recorders DVD players and other source components d Turn the source selection knob to select a live source component Phono Aux Tuner CD Aux2 Aux3 Tape Audio should now be heard when the source component Is played The Exposure 201 0S2 Integrated Amplifier Back View Quick Start Manual Thank you for purchasing the Exposure 2010S2 Integrated Amplifier 5 Remote Control Ground Terminal The source selection knobs w
4. ill rotate to match selections made on Before you start Input Output remote control Contents a Connect RCA Phono cables from source components CD Player TAPE REC provides line level output signals for recording a gl Tuner Tape DVD etc to the respective inputs A Grey Butt e Wy L PRE OUT provides left and right channel output signals appropriate io tush acetal w for connection to an Exposure 2010S2 Power Amplifier select the functions of the Exposure 201052 Integrated Amplifier a future proof upgrade ee i ay Red Button 100 We 3 Loudspeaker Con nections a Mutes the volume output to Tape Deck 5 minimum Indicator lights on li mg i VOLUME anrd INEU SELECTION Right Speaker Left Speaker eee k wie ss knobs will be turned off Press the red button again or press the i AJPH TUMER CO Mains cable HS 101 Exposure System remote control fae VOL button to return volume to batteries included ae Aus TAPE voL its previous level and restore Rear of exposure 2010S2 Integrated Amplifier indicator lights ee Preout Left te PROG RANDON TINE SPK1 SPK2 G B TE 0 0 0 PREV NEXT lt SEARCH gt reen Buttons Ensure your unit is switched off and that the volume d e os lo e Increase decrease the volume control knob ts at its minimum PLAY STOP PAUSE OPEN Indicator light on VOLUME knob will flash as volume is adjusted Please note that your 2010S2 Integra
5. ive the bass units through the loudspeakers split crossover with the joining links removed Check your loudspeaker user manual for the wiring connections 2 Follow the diagram on the right for connecting a pair of loudspeakers in bi amping mode Although the Exposure 201052 Integrated Amplifier is able to drive almost any loudspeaker system the best results will most likely be achieved with speakers rated at 8 Ohms While the Exposure 2010S2 Integrated Amplifier is compatible with most types of loudspeaker cables the type of cables used can influence the subjective performance of your system Right Speaker Left Speaker Rear of Exposure 201 0S2 Integrated Amplifier Preout Right Left SPK SPK2 SPKI SPK2 D o reer r 0 High Frequency i High Frequency L rFZF Rear of exposure 2010S2 Power Amplifier INPUT Right Left SPKI SPK2 SPKI SPK2 Low Frequency Connecting a pair of loudspeakers in bi wiring mode Please ask your Exposure dealer for advice on bi amping loudspeaker cable compatibility and how to get the best from your Exposure 201052 Integrated Amplifier Note Exposure 201052 Integrated Amplifier is internally protected against damage from short circuits However no such protection is infallible and damage may occur if positive and negative speaker cables are inadvertently connected together Installation of a MC or MM Phono Module
6. s operation For details please refer to the Extended Set Up section overleaf or use Exposure speaker cables with your Exposure equipment arm grounding wire or RCA ground wire only please refer to the Extended Set Up instructions overleaf contact your dealer Exposure 2010S2 Integrated Amplifier Extended Set Up Bi wiring The Exposure 201052 Integrated Amplifier is fitted with two sets of 4mm loudspeaker sockets for bi wired connection Another pair of speaker wires Is required for this operation Ensure that the links at the speaker terminals between the high frequency and the low frequency are removed on both loudspeakers 2 Follow the diagram on the right for connecting a pair of loudspeakers in bi wiring mode Please refer to the manufacturer of your loudspeakers for advice on the practicality and potential benefits of bi wiring Bi amping of Loudspeakers Right Speal Left Speak eee Rear of Exposure 2010S2 Integrated Amplifier sles baad Preout Right Lene SPKI SPK2 SPKI SPK2 0000 k High Frequency l l High Frequency l T Low Frequency ee Connecting a pair of loudspeakers in bi wiring mode Bi amping of suitable loudspeakers using a 201052 Integrated and a 2010S2 Power Amplifier provides a useful gain in subjective performance The Integrated Amplifier is used to drive the treble units and the Power Amplifier is used to dr
7. sitivity 250mV Input Impedance gt 14K Ohms line input Pre amplifier Output gain 8dB Frequency Response Total Harmonic Distortion Signal to Noise Channel Separation A an US cle lt 0 05 at KHz rated power gt QQdB A weighted ref rated output 20Hz 2OKHz gt 60dB Mains Supply 1O 120V or 220 240V 50 60Hz Power Consumption Dimensions H x W x D factory set 2OOVA both channels driven 8 Ohms load 90 mm x 440 mm x 310 mm Nett Weight Unpacked 7 kg Gross Weight Packed 9 kg Exposure Warranty Policy The Exposure warranty entitles you to FREE repair of this unrt for the first three 3 years from the date of purchase This warranty is valid only if the unit is purchased from an authorised Exposure dealer registered with the authorised agent in your country of residence and issued with a recognised warranty card The agent accepts no responsibility for defects arising from accident misuse abuse wear and tear neglect or through unauthorised adjustment and or repair or replacement of any components nor will they accept responsibility for damage or loss occurring during transit to or from the person making a claim under warranty The Exposure warranty covers Parts and labour costs for three 3 years from the date of purchase Please retain your original receipt as proof of purchase and purchase date he guarantee Is extended only to the original purchaser
8. t from mains when not in use for prolonged periods Do not open this unit there are NO user serviceable parts inside except to install or change a phono card e Reduce the volume control to minimum before turning this unit on or off Ensure that this unit is switched off when connecting or disconnecting speaker and interconnect cables Contact Exposure Electronics for advice on moving your equipment to another country or territory Caution For a long and trouble free life of your Exposure 2010S2 Integrated Amplifier please ensure the following e Do not short circuit the speaker terminals Do not remove the cover of the Integrated Amplifier or dismantle the case except to install or change phono card e Protect unit against all forms of liquid Never expose unit to dripping or splashing or place objects filled with water such as vases on the unit Do not operate the Integrated Amplifier in damp environment or allow liquids to enter the unit e Do not attempt to bypass the mains fuse or replace the fuse with one of a different specification e Do not place the Integrated Amplifier in a position which restricts cooling airflow around its case e Do not use abrasive or solvent based cleaning fluids on the Integrated Amplifier s case Failure to observe these precautionary measures may void your warranty Technical Specifications Power Output 1KHz 75 Watts per channel RMS 8 Ohms Input Sen
9. ted Amplifier 980 00 oO M Turntable may take up to 48 hours to run in before reaching Video E a Connect left and right loudspeakers to corresponding left and right its optimal performance Each subsequent run in ma speaker outputs on the amplifier _ ee Black Buttons 78 Hout will then take about 30 minutes b Connect terminal of loudspeaker to terminal of the amplifier poe chi select input sources Indicator c Connect terminal of loudspeaker to terminal of the amplifier light on the INPUT SELECTOR V7 The Exposure 201082 Integrated Amplifier is fitted knob will flash as sources are r E E E AE nical T T ine b Ensure left and right channels are connected correctly Right channel Bi wired connection selected speaker output in the event of a speaker wire short Is marked In red Bi wiring may provide a useful gain in subjective performance Should you choose d oroen oeae output this option please refer to the Extended Set Up instructions overleaf switch off the Amplifier for 5 minutes c The tape input is labeled TAPE PLAY Bi amping of Loudspeakers Installation of a MC or MM Phono Module Turntable connection requires the installation of an optional MM or MC Bi amping of loudspeakers using a 2010S2 Integrated and a 2010S2 Power For optimum performance Phono Card A ground terminal is provided for connection to a turntable Amplifier provides a useful gain in subjective performance For thi
Download Pdf Manuals
Related Search