Zalman CNPS10X Optima
Contents
1. Lowering the fan helps to cool the components on the motherboard Connect the cooler s 4 pin connector to the motherboard s CPU Fan header EN sone AN Caution Please make sure that PWM Control Mode is activated in the motherboard s BIOS settings ZALMAN CO 2 AMD Socket FM1 AM3 AM2 AM2 Installation Unfasten the Bolts on the Cooler s Base one thread insert the AMD A Clip between the Cover and the Base and then refasten the Bolts i E 45 AMD Clip A A Caution Make sure the AMD A Clip s ingresses are flush against the protrusions of the Base Cover Install Bolts to the Backplate according to the Socket Type and secure with Side Caps Take note of the orientation of the Nu2. Lowering the fan helps to cool the components on the motherboard AN Caution Please make sure that PWM Control Mode is activated in the motherboard s BIOS settings
3. X Install the fan so that the ZALMAN logo is oriented in relations to the rear of the case as in the diagram f CNPS 1OxX lt X Recommended cooler orientation may differ according to the motherboard model 4 CPU and RAM interference check limited to systems with RAM heatsinks For Intel and AMD Socket motherboards s with a RAM height of 36mm 1 42 and greater there will be physical interference with the CPU cooler resulting in the inability to utilize dual and full channel modes Please check the height of your RAM modules prior to installation ZALMAN COM 5 Installation 1 Intel Socket 1155 1156 775 and Socket 1366 Installation Unfasten the Bolts on the Cooler s Base one thread insert the Intel Clip between the Cover and the Base and then refasten the Bolts Assim r A Intel Clip LN Caution Make sure the Intel Clip s ingresses are flush against the protrusions of the Base Cover N Si Install Bolts to the Backplate according to the Socket Type and secure with Side Caps Socket 775 Socket 1155 1156 Ss Socket 1366 aN Caution Take note of the orientation of the Nuts and the Side Caps Socket 775 Install
4. User s Manual CNPS10X Optima Intel Socket 1155 1156 1366 775 CPU Core i7 Extreme Core i7 Core i5 Core i3 Core 2 Quad Core 2 Duo Core 2 Extreme Dual Core Pentium Pentium D Pentium 4 Celeron AMD Socket FM1 AM3 AM2 AM2 CPU Llano Phenom II Phenom Athlon II X2 Athlon Athlon 64 Athlon X2 Athlon 64 X2 Athlon FX Athlon 64 FX Opteron Sempron please read the following precautions www ZALMAN com 1 Precautions 1 This cooler must be used with a 120mm fan 2 Do not ingest the Thermal Grease and avoid its contact with skin and eyes If contact is made with skin wash off with water If ingested or irritation persists seek medical attention 3 To prevent possible injuries gloves must be worn while handling this product 4 Excessive force exerted on the fan may cause damage to the fan and or system 5 Use and keep product away from reach of children 6 Check the components list and condition of the product before installation If any problem is found contact the retailer to obtain a replacement 7 During transportation of the system the cooler must be removed Zalman is not responsible for any damages that occur during the transport of a system 8 Product design and specifications may be revised to improve quality and performance Disclaimer Zalman Tech Co Ltd is not responsible for any damages due to external causes including but not limited to improper use problems with
5. ation Remove the Sticker Cover from the Lower Tier of the Loading Block and attach to the Backplate Loading Block Attach Double sided Tape to the Loading Block and remove the Double sided Tape Cover Double sided Tape ee ee Caution Please make note of the orientation of the Loading Block s Installation 3 Socket 1155 1156 1366 Installation Attach Double sided Tape to the center of the Backplate and remove the Double sided Tape s Cover X Socket 1155 1156 1366 Installation does not require the Loading Block the motherboard s Clip Support s installation holes and fasten Align the Backplate s Nuts with to the motherboard SWAG S Apply the enclosed Thermal Grease to the CPU s surface and install the Cooler by fastening the Bolts Fasten the Fan using the Fan Fixing Clips A cy P yp mn At KK CAAA KAA a AAAA DEAU Position the fan as low as possible U
6. electrical power accident neglect alteration repair improper installation or improper testing 2 Specifications ee o Fan Thermal Grease Contents ZM STG2M Range ZALMAN CONK 3 Components 1 Common Components Manual w 5 Z R D D Cooler Fan Fixing Clips q wv vq w 2 O OS L Backplate J y AZ Nuts Bolts Side Cap Double sided Tape Thermal Grease ZM STG2M Loading Block 3 AMD Components 2 Intel Components AMD Clip A ZALMAN COM Socket FM1 AM3 AM2 AM2 sy Intel Clip Socket 1155 1156 1366 775 4 Installation Requirements 1 Space Requirements The cooler s installation requires an unobstructed space of 137mm width 130mm length and 155mm height with the CPU as a central reference point Please check if components such as ODDs and PSU protrude into the required space 2 Air Guide Removal Air guides on enclosures must be removed before the cooler s installation since they protrude into the cooler s required space 130mm Jj X Ny Z ZN 3 Cooler Orientation a As shown in the diagram below it is recommended that the cooler be installed so that air flows from the x 7 cooler toward the enclosure s rear exhaust fan to be released
7. ts and the Side Caps O SA s ALMAN COM 3 Remove the Sticker Cover from the Lower Tier of the Loading Block and attach to the Backplate Loading Block Attach Double sided Tape to the Loading Block and remove the Double sided Tape Cover Double sided Double sided tebe 5 EAS AN Caution Please make note of the orientation of the Loading Block s Installation A AT KK w i Reger 2 y DDD i Wy Wy DD Cooler by fastening the Bolts D c 7p o O O O a Cc oO Sc s5 ge fs Wo re a6 Q 5 N amp with the motherboard s Clip Apply the enclosed Thermal Grease to the CPU s surface and install the Fasten the Fan using the Fan Fixing Clips Align the Backplate s Nuts Position the fan as low as possible Lb
Download Pdf Manuals
Related Search