Premier Mounts MM-CB2 flat panel desk mount
Contents
1. Thread Insert in Flat Panel or Adapter Plate M4 Screw Partially Threaded Into Flat Panel To adjust the position of your displays horizontally Turn the mounting head adjustment knob counter clockwise until the mounting head is lose enough to slide easily along the pole Slide the display or mounting head to the desired position When in place turn the adjustment head clockwise to tighten it Make sure it is completely secure and does not move before you move on to the next display or finish Repeat steps for other displays if desired Loosen Tighten amp Adjust amp Secure Installation Instructions Page 1 D PREMIER MOUNTS CREATING POSITIVE CUSTOMER EXPERIENCES 3100 E Miraloma Avenue Anaheim CA 92806 800 368 9700 USA F 800 832 4888 www mounts com Unit 3 The Moorings Business Park Channel Way Longford Conventry CV6 6RH UK 44 0 2476 644105 F 44 0 2476 644165 Installation Instructions To adjust the tension and or tilt angle of the mounting head Adjust the mounting head by utilizing the 90 continuous tilt until it is in the desired position Remove the side and bottom cosmetic cap from the mounting head Figure 6 Use the supplied socket wrench to tighten both nuts The side nut secures the tilt position Point A while the bottom nut secures the pivot Point B A Do not overtighten the mounting ha2. Installation Instructions MM CB2 Introduction The MM CB2 is a dual multimonitor mount arm that works with any 2 tubing Each mounting head provides 90 of omnidirectional tilt The mounting heads include both 75x75mm and 100x100mm VESA mounting patterns The arm includes integrated cable management tabs to keep wires and cables protected and organized The mounting heads can be horizontally adjusted Slide your mounting arm over the pole and base Figure 1 not included but should be previously installed 2 Determine the position on the pole desired for your mounting arm LZ Once in desired position tighten the two 2 pre intalled M8 x 6mm set screws in the holes in the back of the MM CB2 Tighten with included allen key Figure 2 Figure 1 A Are you installing to a 75x75mm or 100x100mm VESA moutning pattern For 75x75mm use mounting points A For 100x100mm use points B in figure 3 1 Thread the M4 screws to one half of their length into the top two mounting holes on each display but do not tighten the M4 screws at this time 9531 000 041 00 Parts List MM CB2 Dual Multi Monitor Mounting Arm Qty 1 Insert the heads of the M4 screws through the keyhole slots on the mounting head Figure 5 Insert the remaining two 2 M4x10mm screws into the bottom mounting points Figure 4 Repeat sub steps 1 amp 2 for the second display Tighten all M4 screws Do not overtighten the mounting hardware
3. mers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Page 2 DI PREMIER MOUNTS Installation Instructions CREATING POSITIVE CUSTOMER EXPERIENCES 3100 E Miraloma Avenue Anaheim CA 92806 800 368 9700 USA F 800 832 4888 www mounts com Unit 3 The Moorings Business Park Channel Way Longford Conventry CV6 6RH UK 44 0 2476 644105 F 44 0 2476 644165
4. rdware Figure 6 Bottom View PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Custo
Download Pdf Manuals
Related Search