SpeakerCraft SC Pro Commercial 6
Contents
1. Features an 8 polypropylene cone woofer wide coverage ported design and a built in multi tap transformer capable of handling 8 ohm or 70V 100V systems The SC Pro Commercial Sub is ideal for enhancing bass in any commercial applica tion INSTALLATION amp WIRING Because access above the ceiling is not always feasible the installation process has been designed so that it can be done from beneath the ceiling Follow the simple steps below for a professional installation 1 Check for Obstructions Before confirming the placement of the speakers you should carefully consider the location of ceiling joists electrical plumbing and other fixtures that may get in the way If you are installing the speakers into an existing ceiling you can locate obstructions by noting the placement of fixtures and if possible gaining access to an attic or crawl space for further analysis A good stud finder found at any building supply store will help you determine where the joists are located in the ceiling 2 Mark the Hole A template for setting the hole is provided in the box along with two paint mask inserts for use when paint ing Position the template in the desired position and pencil an outline on the ceiling 3 Cut the Hole Once the hole is marked use it as a guide to cut through the ceiling Pull the wiring through the cutout hole 4 Insert the S Bracket Through the Hole The included S Bracket comes with two telescoping tile rails att2. the event that the ceiling tile collapses 10 Insert the grille Again be sure that the transformer tap setting is correct for your system then push the grille firmly into the slot in the speaker baffle PAINTING THE SPEAKERS SC Pro Commercial speakers come standard with a neutral white finish which will match almost any decor However it is very easy to paint the speakers if desired The speaker baffle can be painted either prior to or after installation using the procedure described below 1 Gently clean the speakers with a lightly dampened cloth of mild solvent DO NOT use abrasive materials i e sandpaper or steel wool or harmful chemicals i e gasoline kerosene acetone MEK paint thinner or harsh detergents to clean the speaker as permanent damage may result 2 Remove the grille and replace it with the included clear plastic paint mask prior to painting 3 Apply at least two coats of either latex or oil based paint If using latex paint apply an oil based primer first for best results Paint the speakers by rolling brushing or spraying IMPORTANT NOTES e If Painting the Speaker with the Ceiling Remove the grille and replace it with the included clear plastic paint mask prior to painting When finished remove the paint mask and replace the grille e When Painting the Grille Remove the grille from the speaker Spray painting is highly recommended as the grille holes may clog if paint is rolled or brushed S
3. void if the Serial Number on the product has been removed tampered with or defaced This Warranty is in lieu of all other expressed warranties If the product is defective in materials or workmanship as warranted above the purchaser s sole remedy shall be repair or replacement as provided above In no event will SoeakerCraft be liable for any incidental or consequential damages arising out of the use or inability to use the product even if SpeakerCraft Inc or a Limite SpeakerCraft Inc Authorized Dealer has been advised of the possibility of such damages or for any claim by any other party LIFETIME Some states do not allow the exclusion or limitation of consequential damages so the above limitation and exclusion may not apply All implied warranties on the product are limited to the duration of this expressed Warranty Some states do not allow limitation on the length of an implied warranty If the original retail purchaser resides in such a state this limitation does not apply SpeakerCraft offers a variety of accessories to make your installation of this and other SpeakerCraft products easy economical and professional Contact your authorized SpeakerCraft Dealer for more information For technical inquires please call 1 800 448 0976 or e mail us at techsupport speakercraft com We are available to assist you every weekday except holidays between the hours of 7 00 a m and 5 00 p m PST Declaration of Conformity CE We Spea
4. SC Pro Commercial In Ceiling Speaker System G pam Vw aa 5 G a Vi SC Pro Commerc ial 8 SC Pro Commercial 6 SC Pro Commercial 4 SC Pro Commerc ial Sub SPEAKER COMPONENTS Please use Diagram 1 below to identify speaker components mentioned throughout this manual DIAGRAM 1 J Box Knockout Back Can Seismic Mounting Tab Mounting Foot WavePlane Tweeter Baffle Transformer Tap Selector J Box Lid Terminal Connector Strip DESCRIPTION OF SPEAKERS COVERED IN THIS MANUAL SC Pro Commercial 8 Features an 8 polypropylene cone woofer 1 pivoting dome tweeter WavePlane tweeter baffle wide coverage ported design and a built in multi tap transformer capable of handling 8 ohm or 70V 100V systems The SC Pro Commercial 8 is ideal for large commercial applications SC Pro Commercial 6 Features an 6 polypropylene cone woofer 1 pivoting dome tweeter WavePlane tweeter baffle wide coverage ported design and a built in multi tap transformer capable of handling 8 ohm or 70V 100V systems The SC Pro Commercial 6 is ideal for mid size commercial applications SC Pro Commercial 4 Features an 4 polypropylene cone woofer 5 pivoting dome tweeter WavePlane tweeter baffle wide coverage ported design and a built in multi tap transformer capable of handling 8 ohm or 70V 100V systems The SC Pro Commercial 4 is ideal for small commercial applications SC Pro Commercial Sub 8
5. Through Any remaining connectors can be utilized to pass the signal on to additional speakers in the system Please note that this will result in a parallel connection DIAGRAM 4 For bare wire connection Terminal Connector Strip 1 2 amp 3 4 Knockouts For spade connection For screw down connection 8 Install Speaker into the Ceiling Make sure the mounting feet are turned inward to clear the cutout hole and insert the speaker into the ceiling Position the speaker into the hole Note The flange of the speaker is designed to flex and conform to any small imperfections in the ceiling s surface Tighten the four screws on the front of the baffle only enough to make the flange become snug against the ceiling As you tighten the screws the feet will automatically flip into an outward position thereby clamping the drywall between the feet and the flange CAUTION Over tightening may warp the baffle crack the ceiling cause flange to distort or make the grille difficult to install 9 Utilizing the Seismic Mounting Tab The Seismic Mounting Tab on the side of the speaker may be connected to a second ary support point Construction codes in some regions may require the use of a secondary support point it is recom mended to research construction codes in your area SAFETY WARNING Although its use may be optional in your region SpeakerCraft highly recommends using the Seismic Mounting Tab with a secondary support point in
6. ached which will fit across standard 24 ceiling tiles when extended to full length Follow the directions appropriate for your ceiling type be low a Suspended Ceilings While folded insert the S Bracket through the cutout hole cut in the ceiling Once inserted expand the S Bracket and the tile rails making sure that the bracket opening lines up with the cutout hole in the ceiling See Diagram 2 SAFETY WARNING Although you may adjust the S Bracket along the tile rails for proper alignment with the ceiling hole it is highly recommended that you DO NOT remove the tile rails from the S Bracket at any time if used for Suspended Ceiling Installation Doing so will pose in a serious safety risk b Non Suspended Ceilings The S Bracket is not necessary for this type of installation DIAGRAM 2 l TN f Insert the S Bracket 4 through the cutout AN hole it should be in the U folded position Once it is through the cutout hole expand the S Bracket then expand the telescoping LI LT extension arms Tile Rail 5 Utilizing Knockouts Loosen screws at the top of the J Box and remove the lid to reveal connections The J Box has four knockouts two 2 and two to accommodate standard fittings These can be removed as necessary to feed wire in Connecting speaker or out loop through After the connections are completed in step 7 place the lid back into posit
7. ion and tighten the screws 6 Adjust Transformer Tap Selector Before connecting any wiring adjust the Transformer Tap by turning the knob to the appropriate setting See Diagram 3 Be sure that the setting is correct for your system to avoid damage to the speaker or the amplifier system Do not allow a 70V 100V system to supply more wattage than the setting of the transformer or damage to the transformer will occur Do not connect the speaker to a 70V 100V system when it is set to the 8 ohm set ting transformer bypass or damage to the speaker will occur DIAGRAM 3 oe a a Transformer Tap Selector a ae SC Pro Commercial 8 SC Pro Commercial 6 SC Pro Commercial Sub 8 SC Pro Commercial 4 A 7 Speaker Wire Connections a Wiring Options All wire connections are made inside the J Box at the top of the speaker back can See Diagram 4 There are three ways to connect wires to the speaker e Using stripped wires Pull insulating sleeve off wire ends to reveal stripped wire for wire nut connection e Spade Attach spade plugs to appropriate input or output Slide the spade connectors onto the appropriate tabs e Screw down Screw wire or other connectors directly to the terminal connector strip b Connecting Inputs Use any COM connection to connect the COM wire from the amplifier to the speaker Use any connection to connect the wire from the amplifier to the speaker c Loop
8. kercratt Inc 940 Columbia Ave Riverside CA 92507 declare under our sole responsibilty that the products described in this owners manual are in compliance with technical standards EN 50081 2 EMC Emission f EN 50082 2 EMC Immunity SpeakerCraft Inc 940 Columbia Ave Riverside CA 92507 800 448 0976 Fax 951 787 8747 www speakercratt com SpeakerCraft 940 Columbia Avenue Riverside CA 92507 USA 800 448 0976 Fax 951 787 8747 International 1 951 787 0543 www speakercraft com LIT L13 42455 rev1
9. ormer Taps Sensitivity Frequency Response Power Capacity Coverage Angle Directivity Factor Q Directivity Index DI Diameter x Depth Cut Out Diameter As we incorporate design improvements features and specifications may change without notice 7OV 32W 16W 8W 4W 100V 32W 16W 8W 8Q transformer bypass 85dB 1W 1m 88Hz 20kHz 3dB 78Hz 24kHz 10dB 40 Watts Continuous Pink Noise 130 conical coverage 3 53 average 500Hz 16kHz 4 71 average 500Hz 16kHz 8 5 x 76 208 mm x 192 mm 694 171 mm 5 70V 64W 32W 16W 8W 100V 64W 32W 16W 8Q transformer bypass 87dB 1W 1m 35Hz 200Hz 10dB 60 Watts Continuous Pink Noise Spherical Omnidirectional n a n a 1216 x 13 329 mm x 349 mm 11 292 mm LIMITED LIFETIME WARRANTY SpeakerCraft Inc warrants to the original retail purchaser only that this SoeakerCraft product will be free from defects in materials and workmanship pro vided the speaker was purchased from a SpeakerCraft Authorized Dealer Defective products must be shipped together with proof of purchase prepaid insured to the SpeakerCraft Authorized Dealer from whom they were pur chased or to the SpeakerCraft factory at the address listed on this installation instruction manual Freight collect shipments will be refused It is preferable to ship this product in the original shipping container to lessen the chance of transit damage In any case the ri
10. peakerCraft recommends only light spray painting using 5 parts thinning agent to 1 part paint When finished replace the grille material inside the grille and insert the grille back into the speaker SPECIFICATIONS Speaker Type Tweeter Woofer Transformer Taps Sensitivity Frequency Response Power Capacity Coverage Angle Directivity Factor Q Directivity Index DI SC Pro Commercial 8 Background Foreground In Ceiling Speakers 1 pivoting dome 8 polypropylene cone 70V 64W 32W 16W 8W 100V 64W 32W 16W 8Q transformer bypass 88dB 1W 1m 56Hz 20kHz 3dB 50Hz 22kHz 10dB 60 Watts Continuous Pink Noise 130 conical coverage 3 6 average 500Hz 16kHz 5 23 average 500Hz 16kHz SC Pro Commercial 6 Background Foreground In Ceiling Speakers 1 pivoting dome 64 polypropylene cone 70V 64W 32W 16W 8W 100V 64W 32W 16W 8Q transformer bypass 88dB 1W 1m 70Hz 20kHz 3dB 62Hz 22kHz 10dB 50 Watts Continuous Pink Noise 130 conical coverage 3 51 average 500Hz 16kHz 4 85 average 500Hz 16kHz Diameter x Depth 1216 x 976 1096 x 8716 329 mm x 237 mm 262 mm x 214 mm Cut Oui Diameter 11 8 2 292 mm 225 mm SC Pro Commercial 4 SC Pro Commercial Sub 8 Speaker Type Background Foreground Background Foreground In Ceiling Speakers In Ceiling Speakers Tweeter 2 pivoting dome n a Woofer 4 2 polypropylene cone 8 polypropylene cone Transf
11. sk of loss or damage in transit is to be borne by the purchaser If upon examination at the Factory or SpeakerCraft Authorized Dealer it is determined that the unit was defective in materials or workmanship at any time during this warranty period SpeakerCraft or the SpeakerCraft Authorized Dealer will at its option repair or replace this product at no additional charge except as set forth below If this model is no longer available and can not be repaired effectively SoeakerCraft at its sole option may replace the unit with a current model of equal or greater value In some cases where a new model is substituted a modification to the mounting surface may be required If mounting surface modification is required SpeakerCraft assumes no responsibility or liability for such modification All replaced parts and product become the property of SpeakerCraft Inc Products replaced or repaired under this Warranty will be returned to the original retail purchaser within a reasonable time freight prepaid This Warranty does not include service or parts to repair damage caused by accident disaster misuse abuse negligence inadequate packing or shipping procedures commercial use voltage inputs in excess of the rated maximum of the unit or service repair or modification of the product which has not been authorized or approved by SpeakerCraft This Warranty also excludes normal cosmetic deterioration caused by environmental conditions This warranty will be
Download Pdf Manuals
Related Search