RF-Link ABM-4161
Contents
1. If the signal is poor or there is interference If there is a microwave oven in use in the path between the camera and monitor remove the microwave oven or turn it off Make sure the camera and the monitor is within range of each other range of approximately 450 feet 150 meters in a clear line of sight If the power LED is on but only voice signal input is detected the monitor can be in voice activated mode Press the Auto button to turn on the screen Care and Maintenance Keep all parts and accessories out of children s reach Fingerprints or dirt on the lens surface can adversely affect camera performances Avoid touching the lens surface with your fingers Should the lens become dirty use a blower to blow off dirt and dust or a soft dry cloth to wipe off the lens Keep the camera dry Precipitation humidity and other liquids contain minerals will corrode electronic circuits Do not use or store in dusty dirty areas Do not store in hot areas High temperatures can shorten the life of electronic devices and or melt certain plastics Do not store in very cold areas When the system warms up to its normal temperature moisture can form inside the case which may damage electronic circuit boards 8 e Do not attempt to open the case Non expert handling of the device may damage the system e Avoid dropping or strong shocks e Operate this product using only with the power supply included or provided as an accessory2. new ones Note 2 Remove the batteries from the camera if you do not plan to use it for a prolonged period of time 5 Slide the POWER switch to the ON position The LED on the camera red light will light up Step 4 Note When battery power is sufficient the light is constantly red when it is low the LED light will start blinking Loading the Batteries Using AC Power See Fig 4 1 Plug one end of the power adapter into a wall outlet and the other end into the bottom of the camera Step 1 2 2 Slide the ON OFF switch to the ON position The LED on the camera red light will light up Step 3 1 2 Fine Tuning See Fig 5 Place the camera in a convenient location point the lens towards the observation area and adjust the angle by rotating the lens head 1 3 Night light See Fig 6 Press the night light button the night light LEDs will remain ON 1 4 Night vision The camera has nine high intensity LEDs for picking up clear images in the dark When the built in photo sensor detects low ambient light levels the LEDs will automatically activate 2 Monitor Setup 2 1 Power Supply Loading the Battery See Fig 7 1 Open the battery compartment cover on the rear of the monitor Step 1 2 Insert the battery and make sure the polarity is correct Step 2 Note The monitor uses 3 7V 1000mAH Li ion battery or the household AC power 4 Turn the monitor on Step 3 Note 1 When battery power is sufficient the l
3. the user authority to operate the equipment To comply with FCC RF exposure compliance requirements a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons This Transmitter must not be co located or operating in conjunction with any other antenna or transmitter
4. HF Link 2 4GHz Digital Wireless Color Security Baby Monitor Model ABM 4161 User s Manual Package Content Camera x 1 Monitor x 1 Power Adapters x 2 Battery for Monitor 3 7V 1000mAH Li ion x 1 User s Manual x 1 Figures and Quick Guide Product Layout Monitor Monitor Fig 1 CO N O OO A C N LCD screen Antenna VOX Voice Operated Transmission button Power indicator LED Link indicator LED Volume indicator LEDs Speaker VOX Voice Operated Transmission indicator LEDs Brightness adjustment buttons 10 11 12 13 Power Volume control Power adapter socket Battery compartment Clamp Stand Camera Camera Fig 2 4 O CC WANDA A O N Antenna Power indicator LED Infrared LEDs Lens Supporting stand Night light button Night light Microphone Battery compartment Power ON OFF switch Power adapter socket Set Up 1 Camera Setup 1 1 Power Supply Loading the Batteries See Fig 3 1 Loosen the screw on the bottom of the camera by using a screw driver Step 1 2 Open the battery compartment cover Step 2 3 Insert 4 AAA size batteries follow the plus and minus signs inside the battery compartment Step 3 Note The camera uses either 4 AAA batteries alkaline battery recommended or AC power current 4 Close the battery compartment cover and make sure it is locked securely Note 1 Do not mix old batteries with
5. e Do not overload electrical outlets or extension cords this can result in fire or electric shocks e Doremember that you are using public airwaves when you use the system and that sound and video may be broadcast to other 2 4 GHz receiving devices Conversations even from rooms near the camera may be broadcast To protect the privacy of your home always turn the camera off when not in use Specifications Camera Frequency Antenna Transmission distance Modulation Image Sensor Lensf IR LED Dimensions Weight Power Operating temperature 24 GHz Dipole antenna Approx 450 ft clear Line of Sight Color CMOS image sensor f 3 0mm F 2 4 9 pes 5 40W x 12 84 H x 6 1 D em Without stand 175g DC 6V 800mA or 444A alkaline hattenes C 40 0c 32 F IFF Monitor Frequency Antennas Modulation Display Display colors Bnghtness Control VOX Dimensions Weight Power Operating temperature 2 4 GHz Dipole antenna FHSS 2 36 TFT LCD Full color 5 steps Voice activation 6 6 W xl4 5 H x 4 1 D cm 120g DC 6V 800mA or Litton battery QC 40 C 327F IWF Specifications subject tochange without notice CE 04130 This device 15 for indoor use only FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 ofthe FCC Rules These limits are designed to provide reasonable protection against harmful interference in a
6. ight is constantly red when it is low the LED light will start blinking Note 2 Remove the battery from the monitor if you do not plan to use it for a prolonged period of time 5 Adjust the volume to a comfortable level Loading the Battery Using AC Power See Fig 8 1 Plug one end of the power adapter into a wall outlet and the other end into the bottom of the monitor Step 1 2 2 Turn the monitor on Step 3 3 Adjust the volume to a comfortable level Note 1 When charging starts the POWER LED will appear blue If charging is finished fully charged the POWER LED light will turn red Note 2 When the camera and the monitor is linked the Link LED will become green otherwise the Link LED will become red and blinking Using AC Power 2 2 Brightness Setting See Fig 10 Adjust the Brightness selection button lt t to adjust brightness 2 3 VOX voice operated transmission Function See Fig 11 1 Press the VOX button of the monitor This will turn off the screen but the VOX LED will remain ON blue 2 When the sound from the camera reaches the set level the screen will turn on automatically It will turn off again after 30 seconds if no sound is detected Troubleshooting You don t get a signal at all Make sure the camera and the monitor are turned on Make sure the power plugs are pushed all the way in If the camera monitor is powered by batteries replace all batteries with new ones
7. residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there 1s no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user 1s encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Label Compliance Statement This device complies with Part 15 of the FCC Rules Operation 1s subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Note The manufacturer 1s not responsible for any radio or TV interference caused by unauthorized modifications to this equipment such modifications could void the user s authority to operate the equipment Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void
Download Pdf Manuals
Related Search