Premier Mounts SPI project mount
Contents
1. Lower the mounting legs by rotating the leveling barrel counter clockwise Raise the mounting legs by rotating the leveling barrel clockwise i f Side to Side Identify the projector s approximate front to back Center of Gravity center of gravity Place your hands on each side of the projector and gently lift it an inch from the surface on which it is resting Carefully adjust your grip on the projector until it seems balanced from front to back Mentally note the apparent center of gravity Identify the projector s approximate side to side center of gravity Place your hands on the front and back of the projector and gently lift it an inch from the surface on which it is resting Carefully adjust your grip on the projector until it seems balanced from side to side Mentally note the apparent center of gravity Place the SpiroLock Projector Plate on top of the mounting legs with the center of the plate as close as possible to the projector s center of gravity Front to Back Center of Gravity Page 10 Visit the Premier Mounts website at http www mounts com Installation Instructions SPI 24 Attaching the Projector Plate cont d Verify that the mounting legs are at an equal height Return to Step 3 if they are not at an equal height or the SpiroLoc rojector Plate is not level ee ie Verify the position of the int2. D PREMIER C4 MOUNTS CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS SPI SpiroLock Universal Projector Mount NORTH AMERICA EUROPE 3130 East Miraloma Avenue Swallow House Anaheim CA 92806 USA Shilton Industrial Estate USA and Canada Shilton Coventry England CV79JY Phone 1 800 368 9700 Phone 44 0 2476 614700 Fax 1 800 832 4888 Fax 44 0 2476 614710 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 9530 005 051 02 A SPI Weight EIMit inseem a a E A E E a aE A E aN a 2 Warning Statement 0 ccc cennau iier iiine KEANE ANENE ENANA KENNET ened dees REAREA KEKENAN NEENA N NEAN EANET 2 Mmstalation TOOIS saswsrecsnnancnenanno a a E E EAT EEEE E AE E beeddenavieneee 3 Parne Cio eirs digs ket spa vent re E TE E TSSA TE E EEA EE E 3 FO AtUleS enni E EE E EEEE 4 Installing the SpiroLock MOUNE 0 22 cc 22 ceageecseeedaasacceecaaseeeceedduueeceeenanescceeesaeadecuedaauyececehabesseceaaseedecdenaegeeeeceneneeceeetervaces 5 aligece U Coil e Peennereneerreee npn eerrerrrernerecrrererrecerrrceercer erect rercerertrrrererrcerreer rrr errr erp terre eter rrrcer reer rr ereprcerre etree rere rr cer eer errr ree 5 Wood Stud Installation 0 00 0 ee tn nnn nn nn ene TAONE KEETE eee ee AENEA DENN ARATE KEREON NAREN 6 Solid Ceiling INStallation sssrinin EN E E EEE T 7 Attaching the Projector Plate sscisiessirirninriniasninn naini nnnnn ennienni ANE EENET NANEN REN
3. If necessary use a hammer to lightly tap each W wedge anchor into place Move the SpiroLock Ceiling Plate back into position Thread a wedge anchor nut and washer if provided with the wedge anchor onto each threaded wedge anchor shaft Do not tighten any of the wedge anchor nuts and any washers until all nuts and washers are threaded onto the shafts A Do not overtighten the wedge anchor nuts Proceed to the Attaching the Projector Plate section Page 8 Visit the Premier Mounts website at http Avww mounts com Installation Instructions SPI 24 Attaching the Projector Plate Selecting the Mounting Hardware Insert a small straw or toothpick into the threaded inserts found on the bottom or top of the projector Use a pencil to mark the depth of the threaded insert on the small straw or toothpick Mark the straw or toothpick 1 8 above the depth of the threaded insert as shown in Figure 1 Insert the small straw or toothpick into the remaining threaded inserts to compare and verify their depth using the straw or toothpick s 1 8 allowance mark Locate the correct diameter screw for the threaded insert If the screw you selected is longer than the 1 8 arra PAS allowance mark on the small straw or toothpick as Allowance shown in Figure 2 and Figure 3 do not use this screw Marking the Depth The screw length must not bypass the mark Threaded Insert Test each size of the s
4. Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Disclaimer Premier Mounts intends to make this manual accurate and complete However Premier Mounts makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Premier Mounts makes no representation of warranty expressed or implied regarding the information contained herein Premier Mounts assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Premier Mounts 2010 Page 16 Visit the Premier Mounts website at http Avww mounts com Installation Instructions
5. con d Insert one 1 14 x 2 screw through each of the mounting holes A on the bottom of the SpiroLock Ceiling Plate and into the pilot holes Tighten each screw until the SpiroLock Ceiling Plate is secure against the ceiling A Do not overtighten the 14 x 2 screws Proceed to Attaching the Projector Plate on page 9 lt Dw Ey Solid Ceiling Installation You can mount the SpiroLock projector mount to any solid surface ceiling which has a minimum 6 thickness For concrete installation use concrete wedge anchors 1 4 recommended to secure the mounting hardware and a masonry drill bit to drill the pilot holes Wedge anchors and masonry drill bits are not supplied Continue on page 8 SE Example Wedge Anchors and Masonry Bit Not included Installation Instructions Visit the Premier Mounts website at http Avww mounts com Page 7 b a 22 SPI Installing the SpiroLock Mount cont d Place the SpiroLock Ceiling Plate into position against the ceiling Use a pencil and mark four 4 mounting hole locations through each of the mounting points B in the SpiroLock Ceiling Plate The target arrow indicates the direction of the projector screen relative to the projector mount Drill a hole at each mark using the appropriate diameter masonry bit for your wedge anchor Remove the nut and washer from the wedge anchors Insert a wedge anchor into each hole
6. ANE ANARAN N ANEN Kaaa EN 9 selecting the Mounting HardWare ccesscsrassie arn niee a E E EE ETE 9 Multiple Mounting Point Installation 2 0 0 0 cee err i i nr ee eee ee eee EASAN eerie eee eenaeeeeeennieeeeeeenneeeeeee 9 single Mounting Point Installati n ensen E sewers sie tevedei E EE EEEREN TEE 12 Attaching the Projector to the Mount 0 eee ei nt nr ne nee nee e nent eee eenieee eee naeeeeeeeaeeeeeeseeeeeeeeaas 12 Alignment amp Fine TUMM scrcas a EEE E E EEE TE EEEE eens 13 REMOVING the PLOPE COR sts ssc ceesenssezceccasssavevesaceaeavess sanuzeavensscadewatssnececeonsaaicaaseasneadedeassadaved a adeant rean A AAEE aaa D A 14 Technical SPSCIICATONS sisri ararnar a EE A A E a NA E SNTE 15 Warranty oraaa shite bea a a smd eco pec e ar a a a aa a ad a aa tei OTE 16 DISCIAINGD erorien ireen a a E E EE E EE R E N E EE EEEE EET 16 Weight Limit THE CEILING STRUCTURE MUST BE CAPABLE OF l SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF Maximum Projector Weight 4 5 bs THE PROJECTOR IF NOT THE CEILING STRUCTURE MUST BE REINFORCED Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS MUST BE READ AND COMPLETELY UNDERSTOOD KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN MUST BE FOLLOWED AS OUTLINED STOP IN THESE INSTALLATION INSTRUCTIONS FAILURE TO DO SO COULD RESULT IN PROPERTY DAMA
7. GE SERIOUS PERSONAL INJURY OR EVEN DEATH SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE TOP PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR INANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS At least two qualified people should perform the assembly procedure Personal injury and or property damage can result from dropping or mishandling the projector If mounting to wall studs or ceiling studs make sure that the mounting screws are anchored into the center of the wall studs or ceiling studs Use of an edge to edge stud finder is recommended Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires in wall Cutting or drilling into an electrical line may cause serious personal injury Make sure there are no water or natural gas lines inside the wall where the mount is to be located Cutting or drilling into a water or gas line may cause severe property damage or personal injury This product is intended for
8. crews provided The correct screws should thread easily into the mounting point and not pull out when tension is applied Does your projector have a single mounting point or aq multiple mounting points If it has a single mounting point skip to the Single er opek E er Topiek Mounting Point Installation section on page 12 If it has multiple mounting points proceed to the Multiple Mounting Point Installation section below Multiple Mounting Point Installation Locate the projector s mounting points Position an appropriate number of mounting legs on the projector You can use any combination of three 3 or more mounting legs depending on the number and location of the thread inserts on the projector The number and placement of mounting W points on projectors varies between projector manufacturers Refer to the projector s technical specifications for the number and location of the mounting points Installation Instructions Visit the Premier Mounts website at http www mounts com Page 9 b a 22 SPI Attaching the Projector Plate cont d Insert the mounting hardware as determined in Selecting the Mounting Hardware on page 9 through the leveling barrel into the thread insert of the projector A Do not tighten the mounting hardware at this time Raise or lower each of the mounting legs by rotating the leveling barrels until all of the mounting legs are at an equal height
9. e 7 Installation Instructions Visit the Premier Mounts website at http Awww mounts com Page 5 D Installing the SpiroLock Mount cont d Wood Stud Installation Use an electronic stud finder to locate a ceiling stud closest to your desired installation location Identify the center of the ceiling stud Use a pencil to mark the location of the ceiling stud center The target arrow indicates the direction of the ui projector screen relative to the projector mount Place the SpiroLock Ceiling Plate against the ceiling Its mounting holes should align with the center of the ceiling stud Use a pencil and mark two 2 mounting hole locations through each of the mounting points A in the SpiroLock Ceiling Plate Remove the SpiroLock Ceiling Plate and set it aside Drill a pilot hole in the center of each mark using a hand held drill and a s drill bit Pilot Holes W When a screw is driven into a material such as wood it can act as a wedge generating outward pressure which can cause many materials to split Drilling a small pilot hole where the screw will be driven causes less wedging to take place thereby reducing the likelinood of the material being split It also reduces the possibility of the screw head getting sheared off by torque Installation Instructions Page 6 Visit the Premier Mounts website at http Avww mounts com SPI 24 Installing the SpiroLock Mount
10. egrated sliding M6 square q nut in the mounting leg relative to a nearby slot on the SpiroLock Projector Plate He If the M6 square nut is not aligned with any slot you T can use any thin implement such as a toothpick to nudge it into alignment Tighten the mounting screws which secure the mounting legs to the projector Do not overtighten the mounting screws Attach the SpiroLock Projector Plate to each of the mounting legs by inserting and tightening one 1 M6 x 12mm screw through the SpiroLock Projector Plate into the M6 square nut on each of the mounting legs A Do not overtighten the M6 x 12mm screw Insert one 1 barrel cap into the end of each leveling barrel Proceed to Attaching the Projector to the Mount on page 12 Installation Instructions Visit the Premier Mounts website at http Avww mounts com Page 11 b a 22 SPI Attaching the Projector Plate cont d Single Mounting Point Installation Use a single 20 x 5 16 screw to attach the SpiroLock Projector Plate to the projector if your projector has only one mounting point A Do not overtighten the 20 x 5 16 screw Attaching the Projector to the Mount If your projector is heavy and or bulky two people may be required to safely attach the projector to the SpiroLock Ceiling Plate If your projector is to be mounted higher than shoulder height you may need to use one or more ladders to safel
11. he projector with both hands and slowly tilting it forward backward and side to side Make precise adjustments by placing the tip of a flat bladed screwdriver between the projector plate and the lip of the spindle then using gentle leverage to make any adjustments Tighten the two 2 M10 x 10mm set screws in the spindle and the M6 x 25mm Lock It screw in the bell housing of the SpiroLock mount to lock in your adjustments A Do not overtighten the two 2 M10 x 10mm set screws A Do not overtighten the M6 x 25mm Lock It screw M6 x 25mm Lock It Screw M10 x 10mm Set Screw Ba Installation Instructions Visit the Premier Mounts website at http Avww mounts com Page 13 gt 4 24 SPI Removing the Projector The SpiroLock projector mount can be removed quickly if the projector needs service If the projector is heavy and or bulky two people may be required to safely remove the projector from the SpiroLock Ceiling Plate If the projector is mounted higher than shoulder height you may need to use one or more ladders to safely remove the projector from the SpiroLock Ceiling Plate Use the M5 security Allen wrench to loosen the M4 x 12mm Lock It screw Place one hand under the projector to support it Lift the locking tab While lifting the locking tab rotate the SpiroLock collar assembly 15 degrees clockwise u
12. indoor use only Use of this product outdoors could lead to product failure and or serious personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 1 800 368 9700 techsupport mounts com Page 2 Visit the Premier Mounts website at http Avww mounts com Installation Instructions SPI 24 Installation Tools The following tools may be required depending upon your particular installation They are not included N Electronic Stud Finder Pencil Phillips Head Screwdriver Parts List Make sure your Premier Mounts product has the following hardware and components before beginning installation If there are parts missing and or damaged stop the installation and call Premier Mounts at 800 368 9700 SpiroLock Mount Hardware SpiroLock Ceiling Plate Qty 1 14 x 2 Wood Screws M5 Security Allen Wrench Mounting Legs M2 5 x 10mm Security Screw Qty 2 Qty 1 Qty 4 Qty 4 wi M2 5 x 12mm Security Screw M3 x 16mm Security Screw M4 x 10mm Security M4 x 12mm Security Screw Qty 4 Qty 4 Screw Qty 4 Qty 4 ToT 00T TETT M5 x 12mm Security Screw Qty 4 M6 x 12mm Security Screw 14 20 x 5 16 Security Screw M3 Flat Washer Lock It Security Qty 8 Qty 10 Barrel Qty 1 Installation Instructions Visit the Premier Mounts website at http Avww mounts co
13. m Page 3 a SPI The SpiroLock Universal Projector Mount is easy to install Snap and lock the projector onto the mount then rotate and pivot freely for the optimal viewing angle The Lock It security screws and leveling barrel add an extra layer of security and theft deterrence Ceiling Plate Can easily be installed on either a wood stud or solid ceiling Tool Free Adjustment Precise yaw pitch and roll adjustments without requiring specialized tools SpiroLock Installation Torsion spring mechanism automatically twists and captures the SpiroLock projector plate Locking Tab and Lock It Screw Assures that the projector plate releases only when you want it released Lock It Security Hardware Protect your projector from theft by installing specialized hardware at critical mounting points Radial Glide Technology Up to 6 of smooth adjustment in any direction Mounting Slots Allows you to choose from a variety of mounting options and projector mounting point configurations Mounting Legs Adjustable Leveling Barrels Combined with the numerous You can quickly level the mounting legs projector plate mounting slots the without any specialized tools mounting legs allow for multiple mount configurations Page 4 Visit the Premier Mounts website at http Avww mounts com Installation Instructions SPI 24 Installing the SpiroLock Mount Introduction You may secure the Spi
14. ntil you hear an audible click a You may find it easier to lift the locking tab with WW the thumb of the same hand which rotates the SpiroLock collar assembly Use both hands to rotate the projector plate as shown to separate it from the SpiroLock collar assembly Place the projector on a soft flat surface and disassemble the mounting legs from the projector if neccessary Page 14 Visit the Premier Mounts website at http Avww mounts com Installation Instructions SPI Installing the Lock It Security Barrel Install the security barrel to help lock the projector plate to the projector Determine which leveling barrel will be removed Remove the mounting screw Remove the leveling barrel by turning the leveling barrel counter clockwise Thread in the security barrel clockwise Insert and tighten the mounting screw Attach a theft deterrent device PCB CSL1 or padlock not included through the hole that is on the security barrel M Do not overtighten the mounting screw Technical Specifications All measurements are in inches Counter Clockwise ie Clockwise Installation Instructions Visit the Premier Mounts website at http Avww mounts com Page 15 gt 4 22 SPI Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product
15. roLock mount to either a single ceiling stud or a solid surface ceiling such as concrete Read these installation instructions thoroughly before attempting to install the Premier Mounts product Familiarize yourself with the contents of the package and make sure you have all the parts and tools you need to safely complete the installation Some steps of this installation may require two people to prevent personal injury and or damage to the projector Observe all warnings and utilize proper safety equipment at all times Begin installing the SpiroLock mount by separating the ceiling plate from the projector plate Use the M5 security Allen wrench to loosen the M4 x 12mm Lock It screw Place one hand under the projector to support it Lift the locking tab While lifting the locking tab rotate the SpiroLock collar assembly 15 degrees clockwise until you hear an audible click H You may find it easier to lift the locking tab with WY the thumb of the same hand which rotates the SpiroLock collar assembly Use both hands to rotate the projector plate as shown to separate it from the SpiroLock collar assembly What type of ceiling are you installing to If you are installing your SpiroLock mount to a wood stud proceed to Wood Stud Installation on page 6 If you are installing your SpiroLock mount to a solid surface such as a concrete ceiling proceed to Solid Ceiling Installation on pag
16. to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days
17. y attach the projector to the SpiroLock Ceiling Plate Verify that the locking tab on the SpiroLock collar assembly is in the raised position If the locking tab is in the lowered position lift the locking tab and rotate the SpiroLock collar assembly until it retains the locking tab in the raised position Locking Tab Locking Tab Lowered Position Raised Position Raise the projector with the SpiroLock Projector Plate securely attached to the SpiroLock Ceiling Plate Insert the spindle into the SpiroLock collar assembly Press upward and rotate the projector as shown until the SpiroLock collar assembly locks into place The SpiroLock collar assembly will rotate and produce an audible click O Did the SpiroLock collar assembly lock into place If Yes proceed to ESE If No verify that the locking tab on the SpiroLock collar assembly is in the lowered position and that there was an audible click If the locking tab is in the raised position or you did not hear a click lower the projector and return to RAJI Page 12 Visit the Premier Mounts website at http Avww mounts com Installation Instructions SPI 24 Attaching the Projector to the Mount con d Tighten the M4 x 12mm Lock It screw in the SpiroLock collar assembly Projector not shown for clarity Alignment amp Fine Tuning Adjust the pitch roll and yaw of the projector up to 6 by firmly grasping t
Download Pdf Manuals
Related Search