Premier Mounts PCM-MS3 flat panel wall mount
Contents
1. Arrows Facing Out Step 1 Install the nylon spacers to the mounting points on the flat panel If the nylon spacers apply to your flat Step 2 Lay left and right mounting brackets stamped A panel please see Page 5 SHOWS TAPE Installation Instructions Page 7 7 24 PCM MS3 Display Align the Mounting Brackets Mounting Bracket Viewing Guide Center Line Step 3 Match the center of viewing guide with the Step 4 The mounting brackets are designed with a enter line you marked in step 1 center of viewing guide on the side of them Securing the Mounting Brackets Screwdriver Dimples M8 M6 M5 M4 The Griplate have M4 M5 M6 and M8 hole patterns to fit the hardware that your flat panel requires EXAMPLE If your plasma uses 8 x 20 Phillip screws use the M8 mounting points Step 1 Install two 2 M6 x 30 mm Phillip pan screws to the bottom of the left and right hand side mounting brackets Step 2 Once the mounting brackets are aligned secure the Griplate to the flat panel A Note The dimples of the top plates have to be facing up and the bottom dimples must be facing down A Caution Do not over tighten the mounting hardware A Note Secure the two 2 M6 x 30 Phillip pan screws to the left and right mounting bracket Page 8 Installation Instructions PCM MS3 Marking the Wall Viewing Port Wall Marking Wall Structutre Step 1 Align the center viewing port from2. ANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 E Miraloma Avenue Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Installation Instructions Page 13 24 PCM MS3 Page 14 Installation Instructions
3. SES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACH MENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF THE DISPLAY IF NOT THE WALL STRUCTURE MUST BE REINFORCED PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN AS OUTLINED IN THE INSTALLATION INSTRUCTIONS MUST BE ADHERED TO FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH DO NOT USE THIS MOUNT WITH A DISPLAY WEIGHING IN EXCESS OF 160LBS SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COM PLETELY UNDERSTOOD THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE Indicates that the power plug is to be disconnected Contact Premier Mounts with any questions from the power outlet Yd 800 368 9700 Safety precautions must be taken at all times Warning and Caution statements It is recommended that a maxim
4. b 4 PREMIER MOUNTS The original holding company INSTALLATION INSTRUCTIONS PCM MS3 Universal Flat Panel Mount AUSTRALIA NEW ZEALAND OCEANIA NORTH AMERICA EUROPE DISTRIBUTOR 3130 East Miraloma Avenue Swallow House P O Box 295 Anaheim CA 92806 USA Shilton Industrial Estate Mordialloc Victoria 3195 e Shilton Coventry England CV79JY Australia Fax 800 832 4888 Phone 44 0 2476 614700 Phone 039586 6330 Fax 44 0 2476 614710 www premiermounts com au Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 Premier Mounts 2008 9531 099 001 02 PCM MS3 Warning ela 2 Parts 3 Installation Tools iaia 3 Thread Depth Indicatoti ipiici iii ai e 6 eci Aree 7 Secunne the Mounting Brackets iuuiii aree ai 8 Markup tlie Wall nostri Aa OA GA RAGA 9 Lower Mounting Pots m 9 PCM MS3 Installationi i arie ica aaa 10 5 iue muU EE MEI 11 Lateral Shaft Adjustment terere pue PEERS aa Gra Safety Knurl Knob Installation 5 8 ca etant tete iaia ili ila LINGE ELEM UELLE Warning Statements 6 go oO N PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPO
5. hread Insert Thread Depth Indicator Figure 1 Screw Marking Screw Marking Thread Depth Thread Depth Indicator Indicator Figure 2 Figure 3 Page 6 Installation Instructions PCM MS3 Mount Orientation Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to Failure to do STOP so could result in serious personal injury and possible damage to the flat panel Invert the flat panel place it on a soft flat surface to prevent damage to the flat panel Use a blanket foam etc Failure to do so STOP will result in damaging the flat panel Do not lay the flat panel on the floor without any protection to the glass The flat panel is heavy and fragile At least 2 qualified personnel are strongly recommended for installation of this product Failure to do so could result in serious injury and possible damage to the flat panel Top of Flat Panel Marking the Center Tape Measure Of the Display Bottom of Flat Panel Step 1 Once the flat panel is inverted use a Step 2 Using a pencil lightly mark the center of your measuring tape to find the center of your flat flat panel panel measuring from outside to outside of the chassis Positioning the Mounting Brackets A Caution If your display has uneven mounting points or recessed mounting points please use the provided spacers Page 5 Left Mounting Bracket Right Mounting Bracket Center Mark
6. nical Specifications All measurements are in inches mm 36 00 014 40 32 00 812 80 24 00 609 60 18 00 487 20 I i 4 30 109 22 30 10 a 764 54 a 4 9 29 00 i 10 80 736 60 266 70 e 6 20 16 00 Lm d 18748 8 28 MT ee Page 12 Installation Instructions PCM MS3 Ci Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARR
7. roperly installed to the wall place the carton template on top of the wall plate Place the top wall plate on top of the cardboard template and mark the six 6 mounting points Power Source Area Wall Plate Level and secure the plate to the wall with the reference arrow facing up to the ceiling Secure the plate using commercially available suitable hardware depending on your installation environment Installation Instructions PCM MS3 CA Securing the Display A Wall Plate Step 1 Raise the flat panel with the mounting brackets secured to the flat panel and insert the top and bottom hooks from each bracket to the rods from the wall plates Lateral Shift Adjustment Step 1 Make any lateral shift adjustment and lock it by tightening the two 2 M6 x 30 mm Phillips screws found on the bottom of the mounting brackets Do not over tighten the M6 screws to A Caution we rods M6 x 30mm Lateral Shift Screws Safety Knurl Knob Installation Step 1 Tilt the flat panel and secure the two 2 M6 x 12 mm safety knobs to each of the mounting brackets M6 x 12mm Safety Knurl Knobs To remove the display from the wall simply extend the display to its maximum tilt range remove the two 6 mm safety A Note knurl knobs push the flat panel back to it s flat position loosen or remove the two 2 M6 x 30 lateral shift screws and lift the unit of the wall Installation Instructions Page 11 24 PCM MS3 Tech
8. the carton template to the wall Match the center of viewing port to the center of viewing height desired Step 2 Lower Mounting Points Wall Plate Level Wall Structutre Step 1 Place the upper portion of the bottom wall plate to the reference line and mark the four 4 lag bolt mounting points through the wall plate slots on the wall Level the wall plate with the reference arrow pointing up to the ceiling Step 2 Installation Instructions Mark Bottom of Template Center Line Viewing Port Mark a line on the bottom of the carton template Step 3 Mark Bottom of Template Step 3 Pilot holes are recommended size will depend on the commercially available hardware that will be used Mounting Surfaces Wood Studs Drill six 6 pilot holes in the marked wall Concrete Wall Drill six 6 pilot holes in the marked wall using a commercially available concrete drill bit Center Line Page 9 4 D PCM MS3 Installation Lower Mounting Plate Level Wall Plate Lag Bolt and Washer Step 1 Level and secure the plate to the wall with Step 3 the reference arrow facing up to the ceiling Step 2 Secure the plate using six 6 5 16 x 3 lag bolts and six 6 5 16 flat washers Step 4 Upper Mounting Plate Pilot Hole Step 2 Step 1 1 1 Drill six 6 4 pilot holes to the marked Step 3 Page 10 PCM MS3 When the bottom wall plate is p
9. um of 5 8 plaster board be used when mounting to wooden studs Do not install on a structure that is prone to vibration movement or chance of impact Failure to do so could result in damage to the flat panel display and or damage to the mounting surface Do not install near heater fireplace direct sunlight air conditioning or any other source of direct heat energy Failure to do so may result in damage to the flat panel display and could increase the risk of fire At least two qualified people should perform the installation procedure Injury and or damage can result from dropping or mishandling the flat panel display Installation Instructions PCM MS3 h Parts List are missing and or damaged before beginning installation Ifthere are parts missing and or damaged please stop the This wall mount is shipped with all proper installation hardware and components Make sure that none of these parts A Note installation and contact Premier Mounts 800 368 9700 Wall Plates Qty 2 5 16 x 3 Lag Bolts wooden studs 5 16 Flat Washers Qty 12 Griplate Qty 8 only Qty 12 Thread Depth Indicator Pencil Tape Measure Screwdriver Template Studfinder Installation Instructions Page 3 4 M4 x 16 Mumm ot M4x25 018 MB x 12 mm Qty 8 MS x 16 M5 x 20 M5 x 25 M5 x 50 M6 x 16 aty 8 Qty 8 ev AU Qty 8 E AI Qty 8 M6
10. x 20 mmm Qty 8 Page 4 M6 x 30 M6 x 45 M8 x 20 M8 x 25 M8 x 30 M8 x 35 M8 x 45 M8 x 70 PCM MS3 vo E E eve II ovs c Qty 8 E L A Qr 4 Installation Instructions PCM MS3 A Note The nylon spacers may be stacked to achieve proper spacing Q Installation Instructions 1 4 Nylon spacers large Qty 8 1 2 Nylon spacers large Qty 12 5 16 Flat washers metal Qty 8 1 Nylon Spacers Qty 8 1 4 Nylon spacers small Qty 8 9 16 Nylon spacers Qty 8 O Nylon sleeves Qty 8 Page 5 CD 24 PCM MS3 Thread Depth Indicator 1 Insert the thread depth indicator supplied through the thread inserts found on the back of the flat panel to make sure the inserts measure the same full depth and mark it Figure 1 2 Locate the correct diameter screw for the thread insert Compare your marking to the screws supplied 3 If your selected screw is longer than the marking on the thread depth indicator DO NOT USE this screw 4 The screw length must not bypass the marking Select another screw size Figure 2 and 3 until you find one that comes closest to your mark without going past Inverted Flat Panel Display Marking the Depth T
Download Pdf Manuals
Related Search