Addonics HDUS1125LT
Contents
1. 232 9GB 00 00 00 If the replication process to continue to add additional hard disk device LCD will only show the last completed percentage Once the copying process is complete the LCD will display the following results Async Copy HDD OK 11 Fail 0 Compare Compare HDD is used to see if the data on a source hard disk is identical to the target hard disk after the Copy HD operation Choose option 3 from the menu www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query 3 Compare HDD HDD 11 232 9GB Press ENT to begin the comparison The LCD will display the following info Comp 23MB s 0 232 9GB 00 00 00 Once the comparison is complete the LCD will display the following info as well as the amount of data on the source hard disk Compare OK 11 Fail 0 Dif 0 Async Compare Compare HDD is used to see if the data on a source hard disk is identical to the target hard disk after the Copy HDD operation While compare process is on going allows you to plug in additional target drives and comparison will automatically start for the added target drive Choose option 4 from the menu 4 Async Compare Press ENT HDD 11 232 9GB to begin the async comparison The LCD will display the following info ACmp 23MB s 0 232 9GB 00 00 00 If the comparison process continues to add additional2. Of Use the Up and Down arrow keys to choose 1 Byte 1K 10K 100K 1MB 10MB 100 Mbytes In order to improve the accuracy of pure data can maintain the default settings www addonics com Quick Compare Of Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query Adv Setup Adv Setup of ers expert users access to more advanced system settings To access this option hold down the ESC key for two seconds until it appears 11 Adv Setup Read Error Skip This function sets the system to ignore any errors during the copying process Normally if there is an error during copying a warning is displayed on the LCD By using this function users can also copy a HDD with errors 11 01 Adv Setup Read Error Skip Press ENT to enter the following screen By default this option is set to OFF Use the up and down buttons to enable or disable this option Read Error Skip Of Update Firmware This function is used to update the system s f rmware Download the latest version of the f rmware from the Internet at www addonics com For the complete instructions visit the f rmware update webpage or view the instructions found later in this manual 11 02 Adv Setup Update Firmware Compare Firmware This function is used to compare the current system f rmware version with the new version the user is upgrading to This ensures that the dow
3. Up and Down arrow keys to choose 1 11 Auto Start Timer This option is used to set the period of t automatically once you insert HDD on target port Default is set at OFF use the arrows to choose time www addonics com Auto Start Drive Of ime when the duplicator starts copying 10 10 Setup Auto Start Timer Technical Support M F 8 30am 6 00pm PST Email www addonics com support query Press ENT to enter the following f gure The default is Of Use the Up and Down arrow keys to choose 5 Sec 50 Sec Tolerance Size This option is used to set the tolerance in terms of percentage d Auto Start Timer Of the source and target capacity This is to ensure that when the target drive is smaller than the source drive the duplication process will not start 10 11 Setup Tolerance Size if erence between Press ENT to enter the following f gure The default is Of Use the Up and Down arrow keys to choose 1MB 100MB of source BootTime Delay Tolerance Size 1MB This option is used to to set boot delay time 10 12 Setup BootTime Delay Press ENT to enter the following f gure The default is 5 sec Use the Up and Down arrow keys to choose 0 99 sec Quick Compare BootTime Delay 5 sec This option is used to set the size of each comparison unit 10 13 Setup Quick Compare Press ENT to enter the following f gure The default is
4. copying process remaining time completed percentage The copy speed capacity and time will vary depending on the source hard disk Once the copying process is complete the LCD will display the following results Copy HD OK www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query Functions The copy controller has 11 functions in total with the 11th Adv Setup being a hidden system function that only appears when the ESC key is pressed for 2 seconds until there is a beep These are shown below 1 Copy HDD 2 Async Copy HDD 3 Compare HDD 4 Async Compare 5 PreScan Source 6 ReScan BUS 7 Source Size 8 Secure Erase 9 Overwrite 10 Setup 11 Adv Setup 10 01 Language 10 02 Copy Size 10 03 Startup Menu 10 04 Auto Compare 10 05 Button Sound 10 06 Device Info 10 07 System Info 10 08 Fast Copy 10 09 Auto Start Drive 10 10 Auto Start Timer 10 11 Tolerance Size 10 12 BootTime Delay www addonics com 10 13 Quick Compare Technical Support M F 8 30am 6 00pm PST 11 01 Read Error Skip 11 02 Update Firmware 11 03 Compare Firmware 11 04 Q
5. 1 minute Press ESC key until you see User Abort on the LCD screen 4 Now remove the drive from the duplicator and connect it to your system the HDD should be recognized and be able to initialize again www addonics com Phone 408 573 8580 Fax 408 573 8588 Email http www addonics com sales query
6. TECHNOLOGIES User Guide 1 11 2 5 HDD Duplicator LT HDUS1125LT www addonics com v3 1 11 Technical Support If you need any assistance to get your unit functioning properly please have your product information ready and contact Addonics Technical Support at Hours 8 30 am 6 00 pm PST Phone 408 453 6212 Email http www addonics com support query Table Of Contents Basic Instructions Functions Copy HDD Compare HDD PreScan Source ReScan Bus Source Size Overwrite Setup Advanced Setup Basic Troubleshooting Error Messages List Firmware Update Procedure Basic Instructions Installing drives into the 1 11 Snap In Tr Duplicator Management Power Button Console 1 Be sure the lock on each drive door is in an unlock position If not use the key that comes with the Disk Array to unlock the drive door Pull on the door lever to swing open the drive door all the way Source Drive 1 2 Slide a 2 5 SATA hard drive into the drive slot with the drive connector side facing in The drive should slide all the way into the slot with very little resistance Forcing the drive into the slot will cause drive damage or Destination Drive 2 10 permanent damage to the Disk Array Left to Right Destination Drive 1 3 Once the drive is all the way into the drive slot close the door all the way till the drive door latches securely This will engage power and data connection with gt the hard drive Th
7. are PreScan Source Source Size Copy Size Tolerance Size 2 User Abort Cancel operating Any function and any time 3 No Drive Exist No HDD exist during Device Info operating 4 X Space Not Enough When source capacity is Copy Compare Target Drive Space Not small than target Enough 5 X Space Not Enough When source capacity is Async Copy Async Compare Target Drive Fail small than target 6 PreScan Fail Lose SATA connection PreScan Source during copy or bad sector on HDD 7 Source Drive Read Fail Lose target SATA Copy Async Copy Compare connection on source port during copy or bad sector on source HDD 8 Target Drive Write Fail Lose target SATA Copy connection on target port during copy 9 Target Drive Read Fail Lose target SATA Compare connection on target port during comparing 10 Target Drive Fail Lose target SATA Async Copy Async Compare connection on target port during async comparing 11 Target Drive Not Exist No HDD exist during Overwrite operating 12 One pass Lose SATA connection on Overwrite One pass failed SATA port during Overwrite 13 3pass Lose SATA connection on Overwrite pass 1 failed SATA port during Overwrite 14 7 pass 5220 22 M Lose SATA connection on Overwrite pass 1 failed SATA port during Overwrite If you hear the warning signal while the copying function i s executing a beep every 5 seconds the LCD screen will display the problem status you may press any button to return to the copy progre
8. e LED lit for the drive bere mg slot should lit if the Disk Array already powered on You may lock the drive door with the key on page KA 4 To remove the hard drive from the Disk Array simply follow the step 2 3 in reverse www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query l Connecting the Power Cable and Powering On a Connect the power cord provided from the wall outlet to the back of the tower b Push the power button to turn on the HDD duplicator II The Duplicator Panel There are four buttons and an LCD on the panel of HDD Duplicator 1 LCD shows a function or a message Duplicator Panel 2 2 it is used to scroll up function menus 3 it is used to scroll down function menus a en 4 4 it is used to execute a function 5 it is used to cancel a function v esc 5 lil Duplicating a drive When the duplicator powers on it initializes and goes through the steps below Shows the firmware version Initialize SDRAM s status HD Duplicator Initialize SDRAM 1 1 Ver Detect Drives status Shows the first function Detect Drives 1 Copy HD Copy HDD copies data directly from the source hard disk to the target hard disk Press ENT button to begin copy The system will auto detect the hard disks and show the following info on the LCD Copy 36MBs 0 235 7GB 1 48 The LCD will show the following info during the
9. e the f rmware check that the f rmware was downloaded correctly A failed f rmware upgrade may cause the duplicator to become inoperable If the system is working normally do not attempt this operation If the system is already experiencing problems please contact your distributor for repairs Startup Shutdown Do not suddenly turn of the power while the system is performing an operation After shutting down normally wait a moment usually around 2 seconds before starting the system again so it can run its self diagnostics About Copy HPA The HPA Host Protected Area is a hidden data region def ned in ATA ATAPI 4 This area is not usually accessible to software The SATA HDD Duplicate Controller supports the copying of data from this hidden area Drive islocked cannot be initialized after the SECURE ERASE or OVERWRITE 1 Place drive in the source slot 2 Execute PreScan function for 1 minute 3 Press ESC key until you see User Abort on the LCD screen 4 Now remove the drive from the duplicator and connect it to your system the HDD should be recognized and be able to initialize again www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query Error Messages List NO Error Messages Description Applied to 1 Source Drive Not Exist No source HDD exist Copy Async Copy Compare during operating Async Comp
10. hard disk device LCD will only show the last completed percentage Once the copying process is complete the LCD will display the following results Compare OK 11 Fail 0 Dif 0 PreScan Source PreScan HDD is used to check if the source hard disk can be accessed properly It also tests the read speed Choose option 5 from the menu 5 PreScan Source Press ENT HDD 11 232 9GB to begin scan The LCD will display the following info Scan 90MB s 1 230 6GB 00 00 27 Once the scan is complete the LCD will display the corresp onding results PreScan OK www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query ReScan Bus ReScan Bus allows swapping the source or target in and out without having to reboot the system Choose option 6 from the menu 6 ReScan BUS Press ENT to re scan hardware The LCD will display the follo wing info Re Scan BUS NOW Yes When the scan is complete the LCD will display the fol lowing info Bus re scan OK Source Size Source Size is used to show the capacity of the source Choose option 7 from the menu 7 Source Size Press ENT and theLCD will show the following info HDD Hitachi Size 232 9GB Then press ENT and the LCD will show the data s size info HDD Hitachi Data 200 9GB Secure Erase Secure Erase is used to wipe the da
11. nloaded f rmware is the latest version The message Last update F W indicates that it is the latest version 11 03 Adv Setup Searching F W Last update F W Compare Firmware gt Please Wait gt OK Quick Erase HDD This function is used to quickly erase all data on the HDD Please backup any important data before using this function 11 04 Adv Setup Quick Erase HDD Press ENT to enter the following screen Use the Up and Down buttons to select the HDD to erase Quick Erase HDD ALL Target CH www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query Press ENT again and the LCD will prompt you to conf rm the erase operation All data will be lost Erase No Full Erase HDD This function is used to full erase all data on the HDD Please backup any important data before using this function 11 05 Adv Setup Full Erase HDD Press ENT to enter the following screen Use the Up and Down buttons to select the HDD to erase Quick Erase HDD ALL Target CH Press ENT again and the LCD will prompt you to conf rm the erase operation All data will be lost Erase No H WDiagnostic Press ENT to enter the following screen This function is used to check that the system is operating normally 11 06 Adv Setup H W Diagnostic Press ENT again to enter the follo
12. rce HDD s host protected area 11 08 Adv Setup Copy HPA The default is OFF Use the ENT Up and Down buttons to change this to On Bum In This function is used to burn test the system reliability 11 09 Adv Setup Burn In Press ENT to enter the following screen Burn In Mode Copy amp Compare Use the Up and Down buttons to choose Compare Async Copy amp Cmp and Async Compare then press ENT to conf rm www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query Basic Troubleshooting LCD If the LCD blank after the device is turned on check that the power cable is properly connected and that the power supply is on Error Message When the system is running a copy operation or hardware diagnostics if the operation is manually terminated by pressing ESC an error message will be shown by the LCD This may lead to an illegal operation and cause the device to stop reminding If this happens the device must be restarted Hard Disk If unable to read the hard disk please check that the data and power cables are properly connected Keys If pressing the keys on the front panel produces no response from the system the keys may have malfunctioned Please check the control panel to see if the wiring has come loose Firmware Upgrade The device can be updated to new versions of f rmware through CD DVD ROM If unable to updat
13. s option is used to control the sound of a button when you press it 10 05 Setup Button Sound Press ENT and theLCD will display the following info Use the Up and Down arrow keys to choose whether button sound is on or of Button Sound On www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query Device Info This option is used to display the details of all hard disks connected to the copy controller Press ENT and the LCD will display each hard disk information i System Info This option displays system information Fast Copy This option displays Fast Copy Fast Copy only copies data on the source drive to the target drives Currently only supports FAT FAT32 NTFS HFS Ext2 and Ext3 partitions Press ENT and the LCD will display the whether fast copy is on or of This function currently only ef ect Ext2 and Ext3 partitions Auto Start Drive 10 06 Setup Device Info 0 Source CH 0 Hitachi 232 9GB 10 07 Setup System Info 10 08 Setup Fast Copy Fast Copy On n order as shown below following info Use the Up and Down arrow keys to choose ive in FAT FAT32 NTFS HFS This option is used to display to copy automatically once y ou insert HDD on target port 10 09 Setup Auto Start Drive Press ENT to enter the following f gure The default is Of Use the
14. sed to select the system s language sup port By default this is set to English Press ENT to change the Language settings Language English www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query Copy Size This option is used to specify the size of the source hard disk for simplifying further copying operations 10 02 Setup Copy Size Press ENT and the LCD will display a detailed list of options as shown below Copy Size 100 1 MB Use the Up and Down arrow keys to choose dif erent copy sizes The system will of er their corresponding percentages so the user can specify the amount to copy from the source hard disk Press ENT to conf rm and save the changes Startup Menu This option allows you to set an option other than Se tup to be displayed as the f rst available option on the menu every time you start the system 10 03 Setup Startup Menu Press ENT then use the Up and Down arrow keys to choose other options By default the f rst menu option is Copy HDD Startup Menu 1 Copy HDD Auto Compare This option automatically compares the source hard disk with the target hard disk after a copy operation is completed 10 04 Setup Auto Compare Press ENT to access option By default it is set to Of Use the Up and Down arrow keys to choose On Auto Compare Of Button Sound Thi
15. ss screen www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query Firmware Update Procedure Requires one hard drive containing the f rmware f le PAWNEE Create a 50MB HDD partition with FAT FAT32 or NTFS f les system on any SATA hard drive Download the f rmware and unzip the f le to BIN f le format Copy the BIN f le onto the 50 MB partition of the HDD Insert this drive to the Source slot of the duplicator For subsystem connect the drive to the Source SATA port Select Firmware Update function under the Setup or Advanced Setup menu and press ENT to do the update To access the Advanced Setup hold onto the ESC button for 5 seconds The new option will appear Once completed it will reboot and show you the new f rmware version Notes SECURE ERASE HDD duplicator sends a WIPE command to the hard drive This command f Ils 00 string to entire HDD OVERWRITE There are three options One pass 3 passes and 7 passes 5220 22 M The duplicator writes a string of pattern over the entire disk one time three times or seven times 5220 22 M is the DoD standard for drive sanitization Please note that some drives may become locked and cannot be initialized after the SECURE ERASE or OVERWRITE Should this happen use the following procedures to unlock the drive 1 2 3 Place drive in the source slot Execute PreScan function for
16. ta of the hard disk it will erase all of HDD of duplicator included Source HDD Choose option 8 from the menu 8 Secure Erase Press ENT to access option By default it is set to No Use the Up and Down arrow keys to choose Yes Wipe all data Continue No Press ENT and theLCD will show the following info www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query In Process Elapsed 01 00 Overwrite Overwrite is used to overwrite the data of the hard disk it will erase all HDDs connected to the duplicator including Source HDD There are 3 sub options One pass 3 pass and 7 pass Choose option 9 from the menu 9 Overwrite Press ENT to access option By default it is One pass Use the Up and Down arrow keys to choose other options 9 01 Overwrite One pass Press ENT to access option By default it is set to No Use the Up and Down arrow keys to choose Yes Wipe all data Continue No Press ENT and theLCD will show the following info In Process Elapsed 01 00 Setup allows various system settings to be changed There are 12 sub options Language Copy Size Startup Menu Auto Compare Button Sound Device Info System Info Fast Copy Auto Start Drive Auto Start Timer Tolerance Size and Boot Time Delay Choose option 8 from the menu 10 Setup Language This option is u
17. uick Erase HDD 11 05 Full Erase HDD 11 06 H W Diagnostic 11 07 Load Default 11 08 Copy HPA 11 09 Burn In Phone 408 453 6212 Email www addonics com support query Copy HDD Copy HDD copies data directly from the source hard disk to the target hard disk Please make sure that the capacity of the target hard disk is equal or larger than the source hard disk Choose option 1 from the menu 1 Copy HDD HDD 11 232 9GB Press ENT to begin copy The system will auto detect the hard disks and show the following copying info on the LCD Copy 36MB s 0 232 9GB 00 00 00 The LCD will show the following info during the copying process elapsed time completed percentage The copy speed capacity and time will vary depending on the source hard disk Once the copying process is complete the LCD will display the following results Copy HDD OK 11 Fail 0 Async Copy HDD This option is used to specify the size of the source for simplifying further copying operations Choose option 2 from the menu 2 Async Copy HDD HDD 10 232 9GB Press ENT Before the start of the reproduction if the console detects that a hard drive capacity is less than source then the LCD will show the corresponding channel number 8 Space Not Enough And then automatically copies The LCD will display the following info Acpy 36MB s 0
18. wing screen The LCD will cycle through the test categories as they are performed The LCD display is tested f rst the control panel is tested next requires manual operation then followed by the system s intemal diagnostics hardware connection test then the RAM and SD Flash test All test results are shown on the LCD This is a simple way to verify that the system is operating normally Press ENT and the system will begin the tests as shown below LCD Test Start Button Test SDRAM Test gt C gt 8192kbytes OK Test IDE 0 1 FlashTest OK Test f nished OK o gt c gt Once the system diagnostics have been completed the Test finished message will appear on the LCD www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query Load Default Press ESC to return to the main menu then use the ENT button to select This function resets all settings to their factory default This function helps the system recover from errors caused by an illegal operation 11 07 Adv Setup Load Default Press ENT to enter the following screen Use the Up and Down buttons to conf rm reset to factory defaults Load Default Conf g Yes If Load Default OK this will be displayed on the LCD as shown below Load Default Ok Copy HPA If this function is set to ON the system will completely copy the data in a sou
Download Pdf Manuals
Related Search