Panasonic DS-PAN-501
Contents
1. C IN BOTTOM of Docking Station www havis com e 1 800 524 9900 Parts Included Docking Station Barrel Lock Latch Handle Locator Pin Latch Tab Tension Release Lever Tension Adjustment Nut Docking Connector Mounting Hole For DS DA 219 Rigid Mount 11mm 7 16 Socket Tool Mounting Plate Ports Strain Relief Hardware Kit pe SSSA This Hardware Kit includes 1 Zip Ties 5 2 Keys 2 SSS f 3 1 4 20 x 5 8 long Button Head Screws 5 4 M4 x 0 7 x 12mm long Pan Head Screws 5 l l Extra hardware screws provided v Oo By A Tools required for installation G VY yY AA amp e 5 32 Hex Drive For attaching Docking Station to Mount with Button Head 1 4 20 Screws e 2 Philips Screwdriver For attaching Docking Station to VESA 75mm hole pattern equipment with Pan Head M4 x 0 7 x 12mm Screws aN HAVIS Installation 1 Identify your required mounting configuration and select the appropriate fasteners from the Hardware Kit OPTION A Motion mounting device with VESA 75mm hole pattern Use Hardware Kit Item 4 M4 x 0 7x12mm long Pan Head Screw OPTION B Havis vehicle motion mounting equipment Use Hardware Kit Item 3 1 4 20x5 8 long Button Head Screws OPTION C Wall Panel mount Hardware not supplied use appropriate hardware for preferred mounting surface OPTION A OPTIONS B amp C M4 x 0 7 x 12mm Pan Head Screws 1 4 20x5 8 Button2. Head Screws OPTION A INSTALLATION A Align Docking Station mounting plate holes with the holes on VESA 75mm hole pattern device Using the 4 M4 0 7x12mm Pan Head Screws Hardware Kit Item 4 secure the Docking Station to device Torque screws to 20 in Ibs 2 3Nm 10 NOTE We recommend applying a drop of medium strength blue thread locking adhesive to the threads of all fasteners www havis com e 1 800 524 9900 Installation continued OPTIONS B amp C INSTALLATION A Once the location is determined for Docking Station insert fastener see options below into mounting surface leaving enough room for Mounting Plate to slide over fastener head OPTION B Use 1 4 20x5 8 Button Head Screws Hardware Kit Item 3 OPTION C Use surface appropriate hardware not provided B Slide Docking Station Mounting Plate over Fastener head and slide Docking Station down so fastener head slips into slot C Ensure correct alignment of Docking Station and insert and fully tighten 2 additional Fasteners by way of the two access holes in Docking Station face D Rotate Docking Station 90 so that access holes are aligned with the other 2 mounting holes Insert and tighten a Fastener into the bottom mounting hole then tighten the top Fastener E Rotate Docking Station back to original orientation 6N HAVIS Cable Management 1 Tip the Docking Station to a position that is comfortable to work with 2 In
3. Owner s Manual Havis Docking Station For Panasonic Toughpad A1 DS PAN 500 Series DS PAN 501 DS PAN 502 DS PAN 503 HAVIS Productivity in motion www havis com 1 800 524 9900 Before Beginning Original Instructions Havis is pleased to provide this Owner s Manual to aid in the proper installation and use of the DS PAN 500 Series Docking Station for the Panasonic Toughpad A1 For questions regarding the set up of your DS PAN 500 Series Docking Station please contact Havis at 1 800 524 9900 or visit www havis com for additional product support and information This Owner s Manual applies to the following Part Numbers DS PAN 501 DS PAN 503 DS PAN 502 e NEVER STOW OR MOUNT THE DOCKING STATION DIRECTLY IN A VEHICLE AIRBAG DEPLOYMENT ZONE e DO NOT USE COMPUTER WHILE DRIVING e READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION e FOR DOCKING STATION MODELS EQUIPPED WITH A BUNDLED POWER SUPPLY DS PAN 502 REFER TO THE SUPPLIED LIND POWER SUPPLY REFERENCE GUIDE EC DECLARATION OF CONFORMITY in accordance with EN 45014 Manufacturers Name Havis Inc Manufacturers Address 47801 Anchor Court Plymouth Twp MI 48170 USA Declares under our sole responsibility that the product Product name Havis Docking Station For Panasonic Toughpad A1 Model DS PAN 50X where X may be any alphanumeric character and which describes product options May be followed by any alphanumeri
4. Warminster PA 18974 47801 Anchor Court Plymouth MI 48170 www havis com 1 800 524 9900 DS PAN 500 SERIES OMN_ 8 12
5. avis Desktop Stand For further Installation Instructions refer to the Instructions included with DS DA 218 Please refer to the OPTION A INSTRUCTIONS on page 5 of this manual for installation instructions DS DA 219 Rigid Mount Bracket For further Installation Instructions refer to the Instructions included with DS DA 219 Rigid Mount option is available for rugged applications where the tilt swivel function is not necessary Installation requires the removal of the Docking Station s Motion Device www havis com e 1 800 524 9900 Related Products Havis offers a wide variety of accessory products specifically for use with the DS PAN 500 Series Docking Station For more information or to order please visit www havis com DS DA 218 Desktop Stand for Tablet Docking Stations Durable stand for mounting tablet Docking Stations for use in the home or office LPS 106 120W Power Supply External in vehicle power supply and cable for Panasonic Toughpad A1 with cigarette lighter adaptor DS DA 219 Rigid Mount exclusively for DS PAN 500 Series Mounting kit designed exclusively for DS PAN 500 Series Docking Stations Intended for rugged environments where tilt swivel function is not necessary DS DA 506 Replacement Tool exclusively for DS PAN 500 Series 11mm 7 16 Socket Tool used to adjust the tilt swivel tension of Docking Station s motion device Havis Inc 75 Jacksonville Road PO Box 2099
6. c characters which describe product options Product Options This declaration covers all options of the above product which bear the CE Marking Is in conformity with the following standards or other normative documents EMC Directive 2004 108 EC EN 55022 2010 Class B Information technology equipment Radio disturbance characteristics Limits and methods of measurement EN 55024 2010 Information technology equipment Immunity characteristics Limits and methods of measurement Directive 2011 65 EU Restriction of the use of certain hazardous substances ROHS BS EN 50498 2010 Section 7 after market electronic equipment in vehicles Supplementary Information The product herewith complies with the requirements of the EMC Directive 2004 108 EC This product requires the use of the provided e Marked automotive power supply when used within vehicles Plymouth twp MI USA August 1 2012 Bruce Jonik Director of Engineering Havis Inc FCC 47CFR Part 15 compliance This is an FCC Class B device Any changes or modifications to the model DS PAN 50X not expressly approved by Havis Inc could void the user s authority to operate this equipment aN HAVIS Table of Contents P aE 1 9 cane ee E ee ee ee eee ere ere E E erry 3 Port Replication Capability 2 2 0 0 cece cece eee nee eeeeeeeeeeeeeeneeaeeneeneenes 3 Parte NC UGS asses aren E E EN EE 4 SEa O eaoin eE E EE E E A EEEE 5 Cable Management seoresniepcirnsoiares a
7. ded for additional monitor connection open access door BEFORE Docking the tablet Operation Docking continued 3 Pivot tablet so the top aligns with the Locator Pin at the top of the Docking Station Lower the Latch Handle to secure tablet in place Latch Tab will engage in front of Toughpad A1 4 For theft deterrence secure tablet by locking Docking Station with supplied key Hardware Kit Item 2 Operation Undocking 1 If previously locked unlock Docking Station using supplied key www havis com e 1 800 524 9900 Operation Undocking continued 2 While holding tablet with one hand lift the Latch Handle on the top of Docking Station W 3 Once unlatched grab both sides of tablet rock the top forward and carefully lift out of Docking Station top end first Operation Tilt Swivel Tension Adjustment NOTE A higher tilt swivel tension may be required for rugged environments in vehicle use 1 Remove the 11mm 7 16 Socket Tool from the back of Docking Station CAUTION Use of a tool other than the supplied Socket Tool may result in damage to Docking Station 2 Slide the Tension Release Lever to the left and hold in place 3 While holding Tension Release Lever in place use the Socket Tool to tighten or loosen the nut until desired Docking Station tilt swivel tension is obtained 4 Replace Socket Tool to the back of the Docking Station Optional Accessories DS DA 218 H
8. rrori Tn r eri iE E 7 Operation DOCK IN ascetics eter tee eects hae I eon ieeee tee 8 Operation Undocking acctcr nen craepsipenpisicndncobutaustesbeisameraseddeneyutesvenenddes 9 Operation Tilt Swivel Tension Adjustment cecceeeeeeeeeeeeeee es 10 Optional CC CSS OMCs ssirisrorsronsrisendis i Eon ni PNS REE E ENEE RE REEE EENEN 11 Desktop Stand DS DA 218 Rigid Mount Bracket DS DA 219 Precautions Do not place metal objects or containers of liquid on top of the Docking Station If a malfunction occurs immediately unplug the Power Supply and remove the tablet Use only the specified Power Supply Part LPS 106 with this Docking Station Do not store the Docking Station where water moisture steam dust etc are present Do not connect cables into ports other than what they are specified for Do not leave the Docking Station in a high temperature environment greater than 60 C 140 F for a long period of time e Do not connect cables to the DC Power Port or Ethernet Port exceeding 3 meters in length Specifications Power Supply Input 12 0 V DC In Dimensions 10 65 27 05 cm H x 6 80 17 27 cm W x 3 90 9 91 cm D Weight 1 46 Ibs 0 54 kg Operating Environment 10 C to 50 C 14 F to 122 F Storage Environment 40 C to 85 C 40 F to 185 F Port Replication Capability of Docking Station amp gt USB 2 0 x2 a Ethernet RJ45 Power Input 12 V D
9. stall all cables that are necessary for computing needs 3 Use Zip Ties Hardware Kit Item 1 to strain relieve cables Each port has an individual Strain Relief Point that should be used to anchor each cable If desired for routing purposes additional Strain Relief Points on each side of Docking Station may be used 4 Create a service loop with cables to ensure that no tension is on the connectors and to enable intended motion 5 Tie off cables onto a stationary part of the mounting system NOTE Ensure the service loop is adequate for rotation between landscape and portrait orientation as well as tilt motion of Docking Station T This loop must be large enough to allow full range of expected rotation and extension without stressing connections Collect cables and secure to the mounting system Note Mounting system not included www havis com e 1 800 524 9900 Operation Docking DO NOT FORCE TABLET ONTO DOCKING STATION IF THERE IS RESISTANCE CHECK ALIGNMENT OF TABLET ON DOCKING STATION NOTE Ensure a proper connection by aligning the tablet s Alignment Sockets with the Docking Station s Alignment Posts Alignment Posts Alignment Sockets DS PAN 500 Series Docking Station Back Side of Panasonic Toughpad A1 2 Hold tablet in landscape orientation with bottom angled toward Docking Station Lower tablet into the bottom of the Docking Station NOTICE If access to tablet s HDMI port is nee
Download Pdf Manuals
Related Search