Gamber-Johnson 7160-0402 holder
Contents
1. GAMBER JOHNSON Very Well Connected INSTALLATION INSTRUCTIONS Product Revision Form Notepad V LT Universal Cradle amp Accessories Rev A INST 562 7160 0402 Notepad V LT Universal Cradle 7160 0251 Screen Support Assembly 7160 0252 LED Light Assembly 7160 0253 Mic Clip Assembly Printing Spec PS 001 7160 0250 Notepad V LT Universal Cradle w Standard Side Clips Notepad V LT Universal Computer Mount 7160 0402 will accomodate computers 8 2 to I1 8 in width 7 58 to 9 3 in depth and up to 1 50 thick The Notepad V LT hold down clips and key lock are designed to securely hold the laptop In the mount and deter theft not prevent It Gamber Johnson recommends taking your laptop out of the vehicle when not In use 9 64 Hex Allen wrench is needed to adjust clip location and postion 16 Wrench or Socket is need to attach Notepad V LT to Gamber Johnson Motion Attachments 2 Phillips screwdriver and a 9 64 Hex Allen wrench are need to mount accessories Vinyl Cap Long Rear Clip Rear Support amp Brace Deck 4 A p Short Rear Clip Side Clips Flat Front Clip Clip Guide N Lockable Latch Tee Nut Offset Front Clip Product Mounting Disclaimer Gamber Johnson is not liable under any theory of contract or tort aw for any loss damage personal inury special incidental or consequential damages for personal injury or other damage of any nature arising directly or indirectly asa result2. of the improper installation or use of its products in vehicle or any other application In order to safely install and use Gamber Johnson products full consideration of vehicle occupants vehicle systems i e the location of fuel lines brakes lines electrical drive train or other systems air bags and other safety equipment is required Gamber Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications and recommendations Gamber Johnson product instruction sheets or workmanship standards as endorsed through the Gamber Johnson Certified Installer Program copyright 2011 Gamber Johnson LLC If you need assistance or have questions call Gamber Johnson at 1 800 456 6868 Fee Rear Support Assembly Two Rear Support Clips must be assembled at the time of installation Attach each Rear Support amp Brace to Tee Nut located in channel on back edge of Notepad V LT using a 8 32 x 38 Socket Head Screw Attach the Long Rear Clip and Short Rear Clip to appropriate Rear Support amp Brace with a 8 external tooth washer Flat Washer and a 8 32 x 38 Socket Head Screw Long Rear Clip 8 External Tooth Washer Flat Washer amp 8 32 x 38 Socket Head Screw 8 32 x 38 Socket Head Screw 8 External Tooth Washer Flat Washer amp 8 32 x 38 Socket Head Screw Short Rear Clip Vehicle Mounting The Notepad V LT Univers
3. to side to avoid any needed ports and lower them so the tab will just clear the top of Adjustment Screw the computer and tighten A snug fit is prefered Push the right side of the Notepad V LT in until the right Side Clips touch the computer Adjust the right Side Clips in the same manner as the left side After pushing the unit together compressing the computer between the Side clips turn the lock body 90 degrees counter clockwise to secure the unit Adjust the Rear Supports side to side and tighten Adjust the Rear Clips to prevent the computer from moving back and tighten 3a Notepaa V LT Accessories 160 0251 Screen Support Assembly The Screen Support Assemly can only be attached to the right side on Notepad V LT Remove the two Phillips Flat Head Screws found at the back right side corner Place Screen Support Assembly over the holes and attach using two 8 32 x 62 Socket Head Screws and two 8 Flat Washers Screen Support Assembly 8 32 x 62 Socket Head Screws amp 8 Flat Washers 1160 0253 Mic Clip Assembly The Mic Clip Assembly can be mounted on any corner of the Notoad V LT that does not have another accessory mounted Remove the two Phillips Flat Head Screws found on the corner Place the Mic Clip Bracket over the holes and attach using two 8 32 x 62 Socket Head Screws and two 8 Flat Washers Attach the Mic Clip using two 6 32 x 25 Phillips Flat Head Screws 8 32
4. al Cradle is designed to be used with Gamber Johnson motion attachments poles and vehicle bases The Sliding Mount Bar feature allows side to side adjustment of cradle to desired mounting position Four 25 Flat Washers and 25 20 x 62 long Hex Head Screws are supplied in the hardware bag to secure motion attachments to the bottom side of the cradle 20 20 x 62 Hex Head Screws amp 25 Flat Washers Sliding Mount Bars on bottom surface Zr Adjusting Notepad V LT for computer Pull to open deck If the latch on Notepad V LT is locked unlock the unit with the supplied keys All Notepad V LT s are keyed alike Unlatch by turning the lock body clockwise 90 degrees Pull the lock side of the Notepad V LT to the right to open the deck Unlock Gad turn locke body Loosen adjustment screws securing front clips rear clips and side clips enough to raise them and move them in the slots Eight Vinyl Caps are included in hardware bag Optional Vinyl Caps to place over clips to protect computer if needed Place the computer on the Notepad V LT deck Slide the computer tight against the Front Clips The Front Clips can be adjusted side to side and also have a slight amount of vertical adjustment The Flat and Offset clios may also swap positions with the offset clip overlapping the fixed deck to accomodate shorter depth computers Slide the computer against the Side Clips on the fixed deck Adjust the Side Clips side
5. x 62 Socket Head Screws amp 8 Flat Washers 6 32 x 25 Phillips Flat Head Screws 4 5 Notepad V LT Accessories Cont 7160 0252 LED Light Assembly The LED Light Assembly can be mounted on any corner of the Notoad V LT Remove the two Phillips Flat Head Screws found on the corner Place the LED Light Assembly over the holes and attach using two 8 32 x 62 Socket Head Screws and two 8 Flat Washers LED Light Assembly 8 32 x 62 Socket Head Screws amp 8 Flat Washers The LED Is powered using the red and black wires on the light base The LED Assembly is designed to operate on 12 VDC IN a negative ground vehicle Connect the RED wire to the positive pole of the vehicle battery or power distribution box It is recommended that a user supplied fuse holder and amp fuse be installed on the red wire Connect the BLACK wire to a suitable chassis GROUND or the NEGATIVE pole of the battery Turn on the LED by pressing the Activation Button on the head on the LED Assembly Activation Button The LED has three light options White Red and White Red Press the Activation Button to toggle thru the options Hold the Activation Button down for approximately one second to turn the LED off ITO
Download Pdf Manuals
Related Search