Jura Impressa J9.3 One Touch TFT
Contents
1. gt Immerse the milk pipe in the receptacle gt Turn the setting wheel of the cappuccino frother to the Milk Foam or Milk 0 position gt Place another receptacle under the cappuccino frother gt Press the Next button Milk system is being cleaned water flows out of the cap puccino frother Water for cleaning milk system gt Rinse the receptacle thoroughly fill it with 250 ml of fresh water and immerse the milk pipe in the water 33 5 Maintenance Dismantling and rinsing the cappuccino frother Changing the filter 34 moe me me pi e P i gt Empty the other receptacle and place it under the cappuc cino frother again gt Press the Maintenance button gt Press the Next button Milk system is being cleaned the cappuccino frother and the pipe are rinsed with fresh water Please select product appears on the display gt Carefully pull the cappuccino frother down and off gt Dismantle the cappuccino frother into its individual parts gt Rinse all parts of the cappuccino frother thoroughly under running water gt Reassemble the cappuccino frother Ensure that all individual parts are correctly and firmly con nected to ensure correct operation of the cappuccino frother gt Firmly attach it to the connector After 50 litres of water have flowed through the filter will cease to work Your IMPRESSA will automatically pro2. gt Unscrew the black connector with the aid of the hexagonal hole on the measuring spoon for ground coffee gt Clean the connector thoroughly gt Screw the connector back on by hand gt Carefully tighten it using the hexagonal hole on the measuring spoon turning by no more than a quarter of a rotation gt Contact customer support in your country see Chapter IL JURA contact details Legal information gt Warm the machine at room temperature gt Switch the IM PRESSA off at the power switch Contact customer support in your country see Chapter IL JURA contact details Legal information i If you were unable to solve the problem contact customer support in your country see Chapter IL JURA contact details Legal information 43 8 Transport and environmentally friendly disposal 8 Transport and environmentally friendly disposal Transport Emptying the In order to protect the IMPRESSA from frost during transport the system system must be emptied Precondition Please select product is displayed gt Carefully pull the cappuccino frother down and off gt Place a receptacle under the connector of the cappuccino frother gt Press the Lportion milk button Machine is heating As soon as the machine has heated up Please select pro duct appears gt Press the Lportion milk button again Lportion milk hot steam is discharged from the connec
3. is displayed P gt Press the P button Maintenance status 17 6 Turn the Rotary Switch until the programme item M ainte nance settings 3 6 is displayed gt Press the Rinse the milk system button Rinse the milk system gt Press the Immediate button gt Press the Save button Saved appears briefly on the display Maintenance settings 3 6 P gt Press the P button to exit programming mode Please select product Energy saving mode In the programme item Machine settings 1 4 6 Save energy you can permanently set an energy saving mode Energy Save Mode E S M m Inactive All speciality coffees speciality coffees with milk and hot water can be prepared without having to wait Before milk preparation the machine heats up m Active Energy saving of up to 40 Soon after the last preparation the IMPRESSA stops heating up As soon as the energy saving temperature is reached this is indicated in the display by the message Save energy this may take several minutes The machine heats up before coffee hot water or milk prep aration Example Proceed as follows to change the energy saving mode from Inactive to Active Precondition Please select product is displayed P gt Press the P button Maintenance status 16 26 Automatic switch off 4 Permanent settings in programming mode T
4. Precondition Fill bean container is displayed O gt Switch the machine off with the On Off button gt Switch the machine off at the power switch gt Open the bean container cover and remove the aroma pres ervation cover gt Clean the bean container with a soft dry cloth gt Fill the bean container with coffee beans then close the aroma preservation cover and the bean container cover 39 5 Maintenance Descaling the water tank Limescale deposits may form in the water tank To ensure correct function of the machine descale the water tank from time to time gt Remove the water tank gt If you use a CLARIS Blue filter cartridge remove this gt Descale the tank with a mild conventional descaling agent in accordance with the manufacturer s instructions gt Rinse out the water tank thoroughly gt If you use a CLARIS Blue filter cartridge insert this again gt Fill the water tank with fresh cold water and reinsert the tank 40 6 Display messages Message Fill water tank Empty coffee grounds contai ner Empty drip tray Drip tray not fitted Please press the Rotary Switch Fill bean container Rinse the milk system Change filter Clean machine Decalcify machine Not enough ground coffee Cause Result The water tank is empty You cannot prepare any products The coffee grounds container is full
5. 60 sec Volume 25 ml 240 ml Milk portion 3 sec PO sec Hot water Low Normal 25 ml 450 ml X high Example Proceed as follows to change the amount of milk for a latte macchiato from 6 sec to 20 sec the interval from 30 sec to 40 sec and the amount of water from 45 ml to 40 ml Precondition Please select product is displayed P gt Press the P button Maintenance status 7 6 gt Turn the Rotary Switch until the programme item Product settings 2 6 is displayed gt Press the Expert mode button Expert mode Next select the button of the product for which you would like to make settings No product is prepared at this point mo gt Press the Latte macchiato button Latte macchiato gt Press the Amount of milk button gt Press the lt or gt button to change setting for the amount of milk to 20 sec 24 4 Permanent settings in programming mode gt Press the Save button Saved appears briefly on the display gt Press the Volume button gt Press the lt or gt button to change setting for the fill vol ume to 40 ml gt Press the Save button Saved appears briefly on the display gt Press the Next button gt Press the Interval button gt Press the lt or
6. Checked documentation amp comprehensible amp complete amp safe DocCert The Instructions for Use has been awarded the seal of approval by the independent German Technical Inspection Agency TUV SUD due to its easy to understand style its thoroughness and coverage of safety aspects Table of contents Your IMPRESSA J9 3 One Touch TFT Control elements 4 Important information 6 PrOD aa eccentric A E eects acca ow E E 6 FO UU Se es estes tte E E doctors Mauer A 6 1 Preparing and using for the first time 9 IURA 0N the Internet secrete ceca acextesu uvatancsscesesnenatesentecaqisensiasteasieadinencsaeenatlsnestckondanuscgedsapsasiiadsiansssiatechnsndenneaete 9 Setting up th Machine ossansnuseasstetiiehstwssiran ccansssuvsiaiteucinoniatsalsaiivitdaasijecoretnsmiaiipisbd daasdhiibabotomisialsenacumossnimneets 9 FAG Me wr ee a a A enero aera Dare ete ee 9 Filing the bean COT ASN seisin enari era EE aaa Anoa 9 ROSSE EA AEE E E E E EEE T E go LRRaCARENA RR 0 Inserting and activating the filter cccsssssssecsssecsssecsssssssecsssessssessssecsssessssessssessssesessessssessssessseessssessesess in Determining and adjusting the water Nardness csssssssessssssssssssssssssssessssssssessssessssessssessssesessesseees 2 Adiusting the ginder esisiini esrin issia ieii 4 2 Preparation 5 Ways of preparing 0ST ACIS sorei enii io AENEA TENEN ENON AAEE 5 a 8 eects aA OTTO eee tter ee ener ere EO i 6 Preparing two speciality C
7. gt button to change setting for the interval to 40 sec gt Press the Save button Saved appears briefly on the display Latte macchiato P gt Press the P button to exit programming mode Please select product Maintenance settings In the programme item Maintenance settings 3 6 you can make the following settings m Filter Activate the CLARIS Blue filter cartridge see Chapter 1 Pre paring and using for the first time Inserting and activating the filter m Water hardness f you do not have a filter cartridge you will need to set the water hardness see Chapter 1 Preparing and using for the first time Adjusting the water hardness m Rinse the coffee system Manual The switch on rinse must be started manually m Rinse the coffee system Automatic The switch on rinse is started automatically m Rinse the milk system After 10 min You are prompted to rinse the milk system 10 minutes after preparation of a speciality coffee with milk m Rinse the milk system Immediate You are prompted to rinse the milk system immediately after preparation of a speciality coffee with milk 25 4 Permanent settings in programming mode Example Proceed as follows to make the machine prompt you to rinse the milk system immediately after preparing a speciality cof fee with milk Precondition Please select product
8. 4 Permanent settings in programming mode Turn the Rotary Switch until the programme item Machine settings 1 4 6 is displayed gt Press the Factory setting button Factory setting Press the Products button Press the Espresso button Espresso Reset this product to the factory setting Press the Next button Saved appears briefly on the display Factory setting Press the P button to exit programming mode Please select product y y y D v Language In this programme item you can set the language used by your IM PRESSA i If you choose the wrong language by mistake you can easily reset the machine to English Press the P button to enter pro gramming mode Use the Rotary Switch to select pro gramme item 5 6 and then press the top left hand button Example Proceed as follows to change the language from English to Deutsch Precondition Please select product is displayed P gt Press the P button Maintenance status 7 6 gt Turn the Rotary Switch until the programme item Machine settings 2 5 6 is displayed gt Press the Choose language button Choose language gt Press the Deutsch button Gespeichert appears briefly on the display Gerateeinstellungen 2 5 6 P gt Press the P button to exit programming mode Bitte wahlen Sie Ihr Produkt 29
9. gt Press the Product counter button The number of speciality coffees prepared is displayed gt Press the t button Information 6 6 P gt Press the P button to exit programming mode Please select product 31 5 Maintenance 5 Maintenance Your IMPRESSA has the following integrated maintenance pro grammes m e pi e Rinsing the machine Rinse the coffee system Rinsing the cappuccino frother Rinse the milk system Cleaning the cappuccino frother Clean the milk system Changing the filter Change the filter Cleaning the machine Clean Descaling the machine Descale Clean or descale the machine rinse the milk system or change the filter when you are prompted to do so Press the P button to view a list of the maintenance pro grammes Maintenance status 1 6 By referring to the bar you can see how soon each maintenance programme is due When the bar is completely filled with red the IMPRESSA will prompt you to perform the maintenance programme The IMPRESSA will not prompt you to clean the milk system In the interests of hygiene you should clean the milk system daily when you have been preparing milk Rinsing the machine You can initiate the rinse operation manually at any time Precondition Please select product is displayed P 32 gt Place a receptacle under the coffee spout gt Press the P button Mai
10. Press the Rotary Switch Machine is being descaled water flows repeatedly out of the connector of the cappuccino frother The operation stops automatically Empty drip tray gt Empty the receptacle under the connector of the cappuc cino frother gt Empty the drip tray and coffee grounds container and put them back into the machine Fill water tank gt Remove the water tank and rinse it thoroughly gt Fill the water tank with fresh cold water and reinsert the tank Please press the Rotary Switch gt Refit the cappuccino frother Cleaning the bean container mo 5 Maintenance gt Place a receptacle under the cappuccino frother and another under the coffee spout gt Press the Rotary Switch Machine is being descaled water flows out of the cappuc cino frother and the coffee spout Machine is heating Machine is rinsing water flows out of the coffee spout The operation stops automatically Empty drip tray gt Empty the drip tray and coffee grounds container and put them back into the machine Descaling is now complete The IMPRESSA is once more ready for use If the descaling operation stops unexpectedly rinse the water tank thoroughly Coffee beans may be covered with a slight oil film which remains on the walls of the bean container These traces may negatively affect the coffee result For this reason clean the bean container from time to time
11. and Please select product appears on the display It is easy to make permanent settings for the amount of water for all speciality coffees and hot water according to the cup size Adjust the amount once as shown in the following example Every time you prepare a drink in the future this amount of water will be dispensed The permanent settings for adapting the amount of water to the cup size for all speciality coffees and hot water follow this model Example Proceed as follows to permanently set the amount of water for one coffee Precondition Please select product is displayed gt Place a cup under the coffee spout gt Press and hold the Coffee button Coffee and the fill volume are displayed gt Hold the Coffee button down until Enough water Press button appears gt Release the Coffee button Preparation starts and the coffee flows into the cup 2 Preparation Hot water A CAUTION 20 p e p e gt Press any button as soon as there is sufficient coffee in the cup Preparation stops Saved appears briefly on the display The set amount of water for one coffee is permanently stored Please select product appears on the display You can alter this setting at any time by repeating the above procedure You can also permanently set the amount for all speciality cof fees and hot water in programming mode see Chapter 4 Per manent settings in pro
12. water from ml to oz Precondition Please select product is displayed P gt Press the P button Maintenance status 1 6 Turn the Rotary Switch until the programme item Machine settings 1 4 6 is displayed gt Press the Units button Units gt Press the oz button gt Press the Save button Saved appears briefly on the display Machine settings 1 4 6 P gt Press the P button to exit programming mode Please select product Restore factory settings In the programme item Machine settings 1 4 6 Factory setting you can reset various settings to their factory settings m Machine All customer settings apart from the filter are reset to factory settings Your IMPRESSA then switches off m Products The settings amount of water aroma temperature etc for any product can be reset individually to the factory settings The corresponding double product is also reset to the fac tory settings at the same time m All products The settings amount of water aroma temperature etc for all products are reset to the factory settings m Display All display settings are reset to the factory settings Example Proceed as follows to reset the values for Espresso to the factory settings Precondition Please select product is displayed P gt Press the P button Maintenance status 7 6 28
13. 4 Permanent settings in programming mode Colour scheme In this programme item you can set the background colour for the display of your IMPRESSA Precondition Please select product is displayed P gt Press the P button Maintenance status 1 6 Turn the Rotary Switch until the programme item Machine settings 2 5 6 is displayed gt Press the Colour scheme button Colour scheme gt Press the lt or gt button to change the setting gt Press the Save button Saved appears briefly on the display Machine settings 2 5 6 P gt Press the P button to exit programming mode Please select product The selected background colour only applies on the selection page of the display showing the speciality coffees 30 4 Permanent settings in programming mode Viewing information In the programme item Information 6 6 you can view the follow ing information m Product counter Number of prepared speciality coffees speciality coffees with milk and hot water m Maintenance counter Maintenance status and number of maintenance programmes performed cleaning descaling changing the filter m Version Software version Precondition Please select product is displayed P gt Press the P button Maintenance status 16 gt Turn the Rotary Switch until the programme item Informa tion 6 6 is displayed
14. EA E E 30 Viewing information saspsicecscosussniensezsnsensvecerineedneuruscinieennrenipesumeneierronetunensaemeyindedesountiudeapinmeivoo 31 Table of contents 5 Maintenance 32 RINSING the MACHING csssssessssssssesssessssssessssssesssssseeecssessesesseeetesscseeesensessssseotsseseeesseseetesessenstaseenetesseeerensens 32 Rinsing the CAPPUCCINO Ote axcsesnivaxssiennndsestasnovsesinnenindsdusesinewnmuei tis dunadniiddnnediiisuiinninnanidiionTametel 33 Cleaning the cappuccino frothef essessssresssresssresssrensrrenssrennnrennnrennnnennrinnnrnennnnennrnennnnennrnennrnennnrennnrnnnnne 33 Dismantling and rinsing the cappuccino frother ss ssssssseesrrnsrrnsnrennrnnnrnnnrnnnnnnnnnnnnnnnnnnnnrnnnrennrnnnnrennrne 34 Bepo CNS EM E EA EATE A EE 34 cenina Nemi CN oe E E E 36 Descaling the machi cszses cece snatczasesasueizecesaaiiccusa gusbiascaesssuiiciccehesasaaecenssinestonshesaneueds toed aiina 37 Cleaning the bean container csi ssiveriivocsavsivisvivaeevinsnitisctcapspidirivoaaieticiiiienianburddsitdinansidirnivnmaatiindtiieraanes 39 Descaling the water tank ccccsssssssscssesssssssssssesecsssssesesseessssseseesssssesssseesessesseeesssetssssseesesseneasssesensen 40 6 Display messages 41 7 Troubleshooting 42 8 Transport and environmentally friendly disposal 44 Transport Emp ING MNE Sy SOU aeexecesesssttessscpcxstetsansarnede2ieuilsorttecaetasencdde exvendasannsslongssldS iesaceuseadedetetebaneeadeie 44 Di TOS nn ee EA E ee a ee ee
15. Maintenance Cleaning the machine gt Perform descaling see Chapter 5 Maintenance Descaling the machine gt The next time you prepare a bever age add more ground coffee see Chapter 2 Preparation Ground coffee 41 7 Troubleshooting 7 Troubleshooting Problem When preparing a latte macchiato the typical three layers do not form Insufficient foam is produced when the milk is frothed or milk sprays from the cappuccino frother Coffee only comes out Cause Result The cappuccino frother is dirty Coffee or ground coffee Action gt Turn the setting wheel of the cappuc cino to the far right and the Milk Foam position gt Change the length of the interval to at least 30 seconds in programming mode see Chapter 4 Permanent settings in programming mode Product settings gt Rinse and clean the cappuccino frother see Chapter 5 Maintenance Rinsing the cappuccino frother gt Check that the air intake pipe is fitted on the cappuccino frother gt Rinse or replace the air intake pipe You will find a replacement in the Welcome Pack gt Put the grinder on a coarser setting or in drips when it is being prepared Water hardness cannot be adjusted Fill bean container is not displayed although the bean container is empty Empty drip tray has been ground too finely and is blocking the system The same filter cartridge may have b
16. OM CCS i sicicessacssnecsstscnsandcesatsicsessidusetecenceecvuesesibes senedttedes iosuisauanineanenscisecttetneaads 6 Latte macchiato 1m CCIM sec cetenecesse se dstcte se scec tessa ames ecttcce decease ca ttnanestesabente cers mnteaiadeciesusseonias V Warm MIK and MUK TO ieres E A B CU a o Ea ennie c eE E A EEE TEE OE 8 Permanently setting the amount of water fOr the CUD SIZE esssssessssseesssssssssssseesssssessssseessesseeetsseees p HOEN T E E E EE A eeu ndeceeneeretneeinens 20 3 Daily operation 21 SNA O esise aae E aeea EA a iaee EESE AE S EAE STE 21 BEANE IAA CS A EA AAEE E A A E E A N 21 NNO OR saar E A E EA 22 4 Permanent settings in programming mode 23 FOIE ST VAS crevice exiontu nn eu ccnns nie eeing E AEE E nidae iivooubshininrentindieh 24 Maintenance settingS sacs snctaravsansnaaceoaciettebiaitetinbytitnip sii iansdetonianinettatlissesnnindiibaniniinicdioniiiaadmtneinstetibnn 25 Energy saving TOC crreresacsscte gcc se eeredaceset te coe inenen este ancnceces deals peantie me gucbien tice 26 Automatic switch Off cecnestscevesisntantsconn pneu tucisssaionnenisinisoainetbiaeiiiathitsaae Mueidse innnsuniesiiinetibecoinaidediineisideomni 27 ITE POR IIE Or WITO ce csnnnsrnns carircenngeioeiuntantevecaontdnnnan OENE E 28 Restore factory Settings iiiwiinensceainiiesniatniveracaervcstnnininnnnetiiveiiiistdlaninetanraibsvessniipnniisititeiiiahindeiiieinaennesninisa 28 EURO a A fanbase cee cece one ah iene tee 29 UNA e REN aieeaa ER tr teen E E N E EE
17. You cannot prepare any products The drip tray is full You cannot prepare any products The drip tray is not inserted correctly or is not inserted at all You cannot prepare any products The IMPRESSA is prompting you to perform a rinse or continue a maintenance programme that was already started The bean container is empty You cannot prepare any products The IMPRESSA is prompting you to rinse the milk system The filter cartridge no longer works The IMPRESSA is prompting you to clean it The IMPRESSA is prompting you to descale it There is insufficient ground coffee in the machine the IMPRESSA stops the operation 6 Display messages Action gt Fill the water tank see Chapter 1 Preparing and using for the first time Filling the water tank gt Empty the coffee grounds container and the drip tray see Chapter 3 Daily Operation Daily maintenance gt Empty the drip tray gt Clean and dry the metal contacts on the back of the drip tray gt Fit the drip tray gt Press the Rotary Switch to start the rinse or to continue the maintenance programme gt Fill the bean container see Chapter 1 Preparing and using for the first time Filling the bean container gt Press the Rotary Switch to start rinsing the milk system gt Replace the CLARIS Blue filter cartridge see Chapter 5 Maintenance Changing the filter gt Perform cleaning See Chapter 5
18. amming what is shown in the display Important information Important information Proper use For your safety The machine is designed and intended for private domestic use It should only be used for coffee preparation and to heat milk and water Use for any other purpose will be deemed improper JURA Ele ktroapparate AG cannot accept any responsibility for the conse quences of improper use Before using the machine read these instructions for use thoroughly and completely and comply with the instructions they contain A warranty service is not applicable for damage or defects caused by non compliance with the instructions for use Keep these instruc tions for use close to the machine and pass them on to the next user Please carefully read and observe the important safety information Set out below To avoid danger of potentially fatal electric shock m Never use a machine which is damaged or has a defective mains cable m Inthe event of signs of damage for example if there is a smell of burning unplug the machine immediately from the mains supply and contact JURA service m lf the mains cable of this machine is damaged it must be repaired either directly by JURA or by an authorised JURA serv ice centre m Make sure that the IMPRESSA and the mains cable are not located close to hot surfaces Be careful to ensure that the mains cable is not trapped and does not rub against sharp edges m Never open and repair
19. e ee ee 44 9 Technical data 45 10 Index 46 11 JURA contact details Legal information 48 Symbol description Warnings A CAUTION A WARNING CAUTION Symbols used gt I ESpresso Always take note of any information marked with the words CAUTION or WARNING and a warning sign The signal word WARNING draws your attention to potential serious injury and the signal word CAUTION to potential minor injury CAUTION draws your attention to potential damage to the machine Prompt to take action This symbol means that you are being prompted to perform some action Information and tips to make it even easier to use your IMPRESSA Display Control elements Control elements 2 3 4 5 6 J 8 1 Bean container cover 2 Water tank cover 3 Bean container with aroma preservation cover 4 Water tank 5 Height adjustable cappuccino frother 6 Coffee grounds container 7 Drip tray 8 Cup platform ne oN Ee oS Filler funnel for ground coffee Storage compartment cover Grinder adjustment switch Hot water nozzle Measuring spoon for ground coffee Height and width adjustable coffee spout Power switch and mains cable side of machine Control elements Top of the machine Front 1 On Off button 4 Display 2 Rotary Switch 5 Buttons button function depends on 3 P P button progr
20. e operation stops automatically and your IMPRESSA is switched off 1 When the IMPRESSA is switched off with the On Off button the machine consumes less than 0 1W of standby energy The machine can be completely disconnected from the power supply using the power switch 4 Permanent settings in programming mode 4 Permanent settings in programming mode Programme item Maintenance status y6 Product settings 2 6 Maintenance settings 3 6 Machine settings 1 4 6 Machine settings 2 5 6 Information 6 6 Press the P button to enter programming mode You can navigate through the programme items and permanently save the required settings simply by turning the Rotary Switch and using the variable buttons The following settings can be made Sub item Clean Descale only if filter is not activated Change the filter only if filter is activated Rinse the coffee system Clean the milk system Expert mode Filter Water hardness only if filter is not activated Rinse the coffee system Rinse the milk system Save energy Switch off after Units Factory setting Choose language Display Colour scheme Product counter Maintenance counter Version Explanation gt Start the required maintenance programme here gt Select your settings for
21. een used several times or the water hardness set incorrectly in the pro gramming mode The CLARIS Blue filter cartridge Is activated The bean monitor is dirty The metal contacts of the use coarser ground coffee see Chapter 1 Preparing and using for the first time Adjusting the grinder gt Perform descaling see Chapter 5 Maintenance Descaling the machine gt Deactivate the filter cartridge in programming mode gt Clean the bean container see Chapter 5 Maintenance Cleaning the bean container gt Clean and dry the metal contacts on is always displayed 42 drip tray are dirty or wet the back of the drip tray Problem Fill water tank is displayed although the water tank is full Little or no water or steam comes out of the Cappuccino frother The pump is very quiet Grinder is making a very loud noise ERROR 2 is displayed Other ERROR messages are displayed Cause Result The water tank float is trapped The connector of the Cappuccino frother may be blocked by milk residues or limescale fragments loosened during descaling There are foreign objects in the grinder If the machine was exposed to the cold fora long period of time heating is disabled for Safety reasons 7 Troubleshooting Action gt Descale the water tank see Chapter 5 Maintenance Descaling the water tank gt Remove the cappuccino frother
22. er for coffee flows into the cups Preparation stops automatically and Please select product appears on the display Proceed as follows to prepare two cups of coffee at the touch of a button Place two cups under the coffee spout Press the Coffee button twice within two seconds to start coffee preparation me 2 Preparation Latte macchiato Your IMPRESSA can prepare a latte macchiato or cappuccino at the Cappuccino touch of a button There is no need to move the glass or cup Example Proceed as follows to prepare one latte macchiato gt Remove the protective cover from the cappuccino frother gt Attach the milk pipe to the cappuccino frother Use the long pipe for a milk carton and the short pipe for a milk container gt Insert the other end of the milk pipe into a milk carton or connect it to a milk container gt Place a glass under the cappuccino frother gt Turn the setting wheel of the cappuccino frother to the Milk Foam position gt Press the Latte macchiato button Latte macchiato the milk foam is prepared Preparation stops automatically when the preset amount of milk is reached 1 There is a short interval while the hot milk separates from the milk foam This allows the typical layers of a latte macchiato to form You can choose the length of this interval in program ming mode see Chapter 4 Permanent settings in program ming mode Product setting
23. gramming mode Product settings To obtain a perfect water flow use the hot water nozzle You can find the hot water nozzle under the cover of the storage compartment The following temperatures can be selected for preparing hot water Low Normal X high There is a danger of scalding from hot water splashes gt m e Avoid direct contact with the skin gt Carefully pull the cappuccino frother down and off gt Open the storage compartment cover take out the hot water nozzle and close the cover again gt Attach the hot water nozzle to the connector gt Place a cup under the hot water nozzle gt Press the Hot water button Hot water and the temperature are displayed By pressing the lt or gt button several times within appro ximately 2 seconds you can set the temperature to your indi vidual preference This setting is not saved Hot water hot water flows into the cup Preparation stops automatically and Please select product appears on the display 3 Daily operation Switching on Daily maintenance 3 Daily operation When the IMPRESSA is switched on it automatically prompts you to perform the rinse operation Start the rinse operation by pressing the Rotary Switch In programming mode you can change this setting so that the machine starts the switch on rinse automatically Precondition Your IMPRESSA is sw
24. he speciality coffees you can prepare are shown on the display at any one time As soon as you turn the Rotary Switch more speciality coffees are displayed in the product selector The product selector disappears automatically after 5 seconds if no preparation is started The following speciality coffees are displayed as standard Espresso Coffee Cappuccino Latte macchiato Hot water Lportion milk Additional speciality coffees in the product selector Ristretto 2 espressi 2 coffees 2 ristretti 2 Preparation Espresso and coffee Espresso and Coffee are prepared following this model Example Proceed as follows to prepare one coffee gt Place a cup under the coffee spout gt Press the Coffee button Preparation will now begin The preset amount of water for coffee flows into the cup Preparation stops automatically and Please select product appears on the display Preparing two speciality To prepare two speciality coffees either use the product selector or coffees press the appropriate preparation button twice Example Proceed as follows to prepare two coffees using product selector gt Place two cups under the coffee spout Turn the Rotary Switch to view the product selector Turn the Rotary Switch until 2 coffees is displayed gt Press the Rotary Switch Preparation starts and the preset amount of wat
25. her gt Press the Rotary Switch Machine is being cleaned water flows out of the coffee spout The operation is interrupted Add cleaning tablet gt Open the cover of the filler funnel for ground coffee gt Insert a JURA cleaning tablet into the filler funnel gt Close the cover of the filler funnel Please press the Rotary Switch Descaling the machine A CAUTION CAUTION CAUTION CAUTION 5 Maintenance gt Press the Rotary Switch Machine is being cleaned water flows repeatedly out of the coffee spout and the cappuccino frother The operation is interrupted Empty coffee grounds con tainer gt Empty the drip tray and coffee grounds container and put them back into the machine Cleaning is now complete The IMPRESSA is once more ready for use The IMPRESSA builds up deposits of limescale over time and auto matically prompts you to descale it when necessary The degree of calcification depends on the hardness of your water If the descaling agent comes into contact with the skin or eyes this can cause irritation gt Avoid contact with the skin or eyes gt Rinse off descaling agent with clean water Should you get any descaling agent in your eye see a doctor If the wrong descaling agent is used the machine could be dam aged and or traces could be left behind in the water gt Use only original JURA maintenance products If the descaling operation is interrup
26. ion purposes only and do not represent the original colours of the machine Some details of your IMPRESSA may vary Your opinion is important to us Use the contact link at www jura com The instructions for use contain information which is protected by copyright It is not permitted to photocopy these instructions for use or translate them into another language without the prior written consent of JURA Elektroapparate AG
27. itched on at the power switch gt Place a receptacle under the coffee spout gt Press the On Off button to switch the IM PRESSA on Welcome to JURA appears on the display The machine heats up Please press the Rotary Switch gt Press the Rotary Switch The machine rinses The operation stops automatically and Please select product appears on the display To ensure that you get many years of reliable service out of your IMPRESSA and to guarantee the optimum coffee quality the machine requires daily maintenance gt Pull out the drip tray gt Empty the coffee grounds container and the drip tray Rinse them both with warm water gt Dry the metal contacts on the back of the drip tray gt Refit the coffee grounds container and the drip tray gt Rinse the water tank with clean water gt Dismantle and rinse the cappuccino frother see Chapter 5 Maintenance Rinsing the cappuccino frother gt Wipe the surface of the machine with a clean soft damp cloth e g microfibre cloth 21 3 Daily operation Switching off 22 When you switch your IMPRESSA off the spouts used to prepare a speciality coffee or milk are rinsed gt Place one receptacle under the coffee spout and another under the cappuccino frother gt Press the On Off button Machine is rinsing Milk system is being rinsed The spouts used to prepare a speciality coffee or milk are rinsed Th
28. mpt you to change the filter After two months the filter will cease to work You can check the elapsed time by referring to the date plate on the filter holder in the water tank If the CLARIS Blue filter cartridge is not activated in program ming mode you will not be prompted to change the filter Precondition Change filter is displayed gt Press the P button Maintenance status 1 6 gt Press the Change the filter button Change the filter If you do not want to start changing the filter just yet press the t button The prompt Change filter remains active mo 5 Maintenance gt Press the Next button Change filter gt Remove and empty the water tank gt Open the filter holder and remove the old CLARIS Blue filter cartridge and filter extension gt Fit the filter extension on top of a new filter cartridge gt Insert the filter cartridge into the water tank exerting slight pressure gt Close the filter holder It will click into place audibly gt Fill the water tank with fresh cold water and reinsert the tank gt Place a receptacle at least 500 ml under the cappuccino frother gt Turn the setting wheel of the cappuccino frother to the Steam position amp gt Press the Next button Filter is being rinsed water flows out of the cappuccino frother You can interrupt rinsing of the filter at any time by pressing a
29. ness Adjusting the water hardness 1 Preparing and using for the first time You can find out what the water hardness Is by using the Aquadur test strip supplied as standard gt Hold the test strip briefly for second under flowing water Shake off the water gt Wait for about one minute gt You will then be able to read the degree of water hardness from the discolouration of the Aquadur test strip and the description on the packaging You can now adjust the water hardness Precondition Please select product is displayed P Q P gt Press the P button Maintenance status 16 gt Turn the Rotary Switch until the programme item Maintenance settings 3 6 is displayed gt Press the Water hardness button Water hardness gt Press the lt or gt button to set the water hardness gt Press the Save button Saved appears briefly on the display to confirm the setting Maintenance settings 3 6 gt Press the P button to exit programming mode Please select product 1 Preparing and using for the first time Adjusting the grinder CAUTION 4 You can adjust the grinder on a continuous scale to suit the degree of roast of your coffee If you adjust the consistency of grind when the grinder is not oper ating the grinder adjustment switch could be damaged gt Only adjust the consi
30. ntenance status 7 6 gt Press the Rinse the coffee system button Machine is rinsing water flows out of the coffee spout The rinse stops automatically and Please select product appears on the display Rinsing the cappuccino frother Cleaning the cappuccino frother CAUTION 5 Maintenance After each milk preparation the IM PRESSA prompts you to rinse the milk system Precondition Rinse the milk system is displayed gt Place a receptacle under the cappuccino frother a gt Press the Rotary Switch Milk system is being rinsed water flows out of the cappuc cino frother The rinse stops automatically and Please select product appears on the display To ensure that the cappuccino frother always works properly you should clean it daily when you have been preparing milk Your IMPRESSA will not prompt you to clean the cappuccino frother If the wrong cleaning agent is used the machine could be damaged and or traces could be left behind in the water gt Use only original JURA maintenance products i JURA Cappuccino Cleaner is available from stockists Precondition Please select product is displayed P gt Press the P button Maintenance status 7 6 gt Press the Clean the milk system button Cleaning agent for milk system gt Pour 250 ml of fresh water into a receptacle and add one capful max 5 ml of Cappuccino Cleaner
31. ny button Press the Rotary Switch to continue rinsing of the filter The water may be slightly discoloured This is not harmful to health and does not affect the taste Rinsing of the filter stops automatically after approximately 500 ml The machine heats up Please select product appears on the display 39 5 Maintenance Cleaning the machine After 200 preparations or 80 switch on rinses the IMPRESSA will prompt you to clean it CAUTION Ifthe wrong cleaning agent is used the machine could be damaged and or traces could be left behind in the water gt mmo mo mme Use only original JURA maintenance products The cleaning programme lasts approximately 20 minutes Do not interrupt the cleaning programme The quality of cleaning will be impaired if you do so JURA cleaning tablets are available from stockists Precondition Clean machine is displayed gt mm e 36 gt Press the P button Maintenance status 1 6 gt Press the Clean button Clean If you do not want to start cleaning just yet press the t but ton The prompt Clean machine remains active gt Press the Next button Empty coffee grounds container gt Empty the drip tray and coffee grounds container and put them back into the machine Please press the Rotary Switch gt Place one receptacle under the coffee spout and another under the cappuccino frot
32. ontainer 39 Cappuccino frother 33 Machine 36 Coffee 6 Coffee grounds container 4 Coffee spout Height and width adjustable coffee spout 4 Consistency of grind Adjusting the grinder 4 Grinder adjustment switch 4 Contact details 48 Cover Bean container 4 Cup platform 4 Customer support 48 46 D Degree of water hardness P Descaling Machine 37 Water tank 40 Determining and adjusting the water hardness 2 Display 5 Display messages 41 Drip tray 4 E Emptying the system 44 Energy saving mode 26 Errors Troubleshooting 42 Espresso 16 F Factory settings Restore factory settings 28 Filler funnel Filler funnel for ground coffee 4 Filling Bean container 9 Water tank 9 Filter Changing 34 Inserting and activating the filter 21 First time use 10 Frother Cappuccino frother 4 G Ground coffee 18 H Hotline 48 Hot water 20 Hot water nozzle 4 Instant coffee Ground coffee 18 Internet 9 J JURA Contact details 48 Internet 9 L Language 29 Latte macchiato 1 M Machine Cleaning 36 Descaling 37 Rinsing 32 Setting up 9 Switching off 22 Switching on 21 Mains cable 4 Maintenance Daily maintenance 21 Maintenance 32 Messages display 41 Milk foam B Milk system cleaning Cappuccino frother cleaning 33 Milk system rinse Rinsing the cappuccino frother 33 Milk warm B P Permanently setting the water for the cup size 9 Permanent settings in programming mode 23 Power switch 4 Preparation b V Cap
33. or the first time JURA on the Internet Setting up the machine Filling the water tank CAUTION Filling the bean container CAUTION Visit us on the Internet You can download short operating instruc tions for your machine from the JURA website www jura com You will also find interesting and up to date information on your IMPRESSA and on every aspect of coffee When setting up your IMPRESSA please note the following m Place the IMPRESSA on a horizontal surface that is not sensi tive to water Choose a spot for your IM PRESSA which protects the machine against overheating Ensure that the ventilation slots are not covered To enjoy the perfect cup of coffee we recommend changing the water every day Milk sparkling mineral water or other liquids can damage the water tank or the machine gt Only fill the water tank with fresh cold water gt Open the water tank cover gt Remove the water tank and rinse it with cold water gt Fill the water tank with fresh cold water and reinsert the tank gt Close the water tank cover The bean container has an aroma preservation cover This will ensure that your coffee beans retain their aroma for longer Coffee beans which have been treated with additives e g sugar ground coffee or freeze dried coffee will damage the grinder gt Only use untreated coffee beans to fill the bean container gt Open the bean container cover and remove the aroma pre
34. out gt Press the Rotary Switch Machine is rinsing the machine rinses The operation stops automatically Please select product appears on the display The IM PRESSA is now ready for use i The display shows the products you can prepare Inserting and activating Your IMPRESSA no longer has to be descaled if you are using the the filter CLARIS Blue filter cartridge If the water hardness is 10 dH or more we recommend using the filter cartridge i m e If you do not know the hardness of your water you must find this out first see Chapter 1 Preparing and using for the first time Determining the water hardness Perform the inserting the filter operation without any inter ruptions This will ensure that your IMPRESSA always produces its best Precondition Please select product is displayed m Q gt Press the P button Maintenance status 7 6 gt Turn the Rotary Switch until the programme item Maintenance settings 3 6 is displayed gt Press the Filter button Filter gt Press the Active button gt Press the Save button Saved appears briefly on the display Insert filter gt Remove the filter cartridge extension from the Welcome Pack gt Fit the filter extension on top of a CLARIS Blue filter cartridge gt Remove and empty the water tank 1 Preparing and using for the first time Dete
35. puccino V Coffee 16 Espresso 16 Ground coffee 18 Latte macchiato Y Milk 18 Problems Troubleshooting 42 10 Index Programming mode 23 Automatic switch off 27 Energy saving mode 26 Language 29 Maintenance settings 25 Product settings 24 Restore factory settings 28 Unit for amount of water 28 Proper use 6 Rinsing Cappuccino frother 33 Machine 32 Rotary Switch 5 Safety 6 Safety information 6 Settings Permanent settings in programming mode 23 Setting up Setting up the machine 9 Short operating instructions 9 Switching off 22 Switching on 21 Switch off Automatic switch off 27 Symbol description 3 Technical data 45 Telephone 48 Troubleshooting 42 Unit for amount of water 28 Use First time 10 Viewing information 31 Warm milk 18 Water tank 4 Descaling 40 Filling 9 Website 9 47 Art 69430 9 3 en 20 1109 u JURA contact details Legal information 11 JURA contact details Legal information Directives Technical changes Feedback Copyright 48 JURA Elektroapparate AG Kaffeeweltstrasse 10 CH 4626 Niederbuchsiten Tel 41 0 62 38 98 233 You will find additional contact details for your country at www jura com The machine complies with the following directives m 2006 95 EC Low Voltage Directive m 2004 108 EC Electromagnetic Compatibility m 2009 25 EC Ecodesign We reserve the right to make technical changes The diagrams used in these instructions for use are for illustrat
36. rmining and adjusting the water hardness gt Open the filter holder and insert the filter cartridge into the water tank exerting slight pressure gt Close the filter holder It will click into place audibly After two months the filter will cease to work You can check the elapsed time by referring to the date plate on the filter holder in the water tank mule gt Fill the water tank with fresh cold water and reinsert the tank gt Place a receptacle at least 500 ml under the cappuccino frother gt Press the Next button Filter is being rinsed water flows out of the cappuccino frother You can interrupt rinsing of the filter at any time by pressing any button Press the Rotary Switch to continue rinsing of the filter The water may be slightly discoloured This is not harmful to health and does not affect the taste mme mme Rinsing of the filter stops automatically after approximately 500 ml The machine heats up Please select product appears on the display The filter is now activated If you are using the CLARIS Blue filter cartridge and have acti vated it in programming mode you will not be able to adjust the water hardness m o The harder the water is the more frequently the IM PRESSA needs to be descaled It is therefore important to adjust the water hardness The water hardness can be adjusted on a continuous scale between P dH and 30 dH Determining the water hard
37. s Coffee preparation starts The preset amount of water flows into the glass Preparation stops automatically and Please select product appears on the display To make sure the cappuccino frother always works properly rinse and clean it regularly see Chapter 5 Maintenance Rinsing the cap puccino frother 1 2 Preparation Warm milk and milk foam Ground coffee Example Proceed as follows to prepare milk foam gt Remove the protective cover from the cappuccino frother gt Attach the milk pipe to the cappuccino frother Use the long pipe for a milk carton and the short pipe for a milk container gt Insert the other end of the milk pipe into a milk carton or connect it to a milk container gt Place a cup under the cappuccino frother gt Turn the setting wheel of the cappuccino frother to the Milk Foam position If you want to heat the milk turn the setting wheel of the cap puccino frother to the Milk position U gt Press the Lportion milk button Lportion milk As soon as the machine has heated up Please select pro duct appears gt Press the Lportion milk button again Lportion milk the milk foam is prepared Preparation stops automatically when the preset amount of milk is reached Please select product appears on the display To make sure the cappuccino frother always works properly rinse and clean it regularly see Chap
38. s ervation cover 1 Preparing and using for the first time First time use A WARNING gt Remove any dirt or foreign objects from inside the bean container gt Fill the bean container with coffee beans then close the aroma preservation cover and the bean container cover If the machine is operated with a defective mains cable there is a danger of potentially fatal electric shock gt Never use a machine which is damaged or has a defective mains cable Precondition The water tank and bean container have been filled gt Insert the mains plug into a power socket gt Switch on the IMPRESSA using the power switch on the right hand side of the machine gt Press the On Off button to switch the IM PRESSA on The JURA logo appears The display then shows the lan guages you can choose from i To display more languages press the Next button bottom right gt Press the button that corresponds to the language you want eg English Saved appears briefly on the display to confirm the setting Please press the Rotary Switch the Rotary Switch lights up gt Place a receptacle under the cappuccino frother gt Press the Rotary Switch System Is filling the system fills up with water The opera tion stops automatically Please press the Rotary Switch 1 Preparing and using for the first time gt Place a receptacle under the coffee sp
39. speciality coffees and hot water gt Indicate whether you are operating your IMPRESSA with or without a CLARIS Blue filter cartridge gt Adjust the water hardness gt Change the settings for the switch on rinse and milk system rinse gt Select an energy saving mode gt Set the time after which the IM PRESSA should switch off automatically gt Select the unit for the amount of water gt Reset the permanently set values of all products to the factory settings gt Select your language and the back ground colour for the display gt Keep track of all speciality coffees prepared and view the number of maintenance programmes performed 23 4 Permanent settings in programming mode Product settings In the programme item Product settings 2 6 you can make indi vidual settings for all speciality coffees and hot water The following settings can be made Product Temperature Coffee strength Amount Ristretto Normal High extra mild 2 mild 22 Volume 25 ml 240 ml espresso normal 22 strong 2222 coffee extra strong 24222 Two ristretti Normal High Volume 25 ml 240 ml two espressi per cup two coffees Latte macchiato Normal High extra mild 2 mild 22 Amount of milk Cappuccino normal 222 strong 2222 3sec DO sec extra strong 2222 Interval 0 sec
40. stency of grind when the grinder is run ning The consistency of grind setting is correct if the coffee flows regu larly from the coffee spout In addition a fine thick crema forms Example Proceed as follows to change the consistency of grind during the preparation of an espresso gt Open the storage compartment cover gt Place a cup under the coffee spout gt Press the Espresso button The grinder starts up Espresso is displayed gt Turn the grinder adjustment switch to the desired position while the grinder is running The espresso is prepared and the consistency of grind is adjusted gt Close the storage compartment cover 2 Preparation Ways of preparing a beverage me mm o p e i 2 Preparation You can stop preparation of a speciality coffee speciality cof fee with milk or hot water at any time Just press any button During the grinding operation you can select the coffee strength of individual products by turning the Rotary Switch 2 extra mild 2 mild 222 normal 2222 strong or 22222 extra strong During preparation you can change the preset amount of water by turning the Rotary Switch or pressing the lt and gt buttons You can follow the current status of preparation on the display You can make permanent settings for all products in programming mode see Chapter 4 Permanent settings in programming mode Product settings Only some of t
41. ted there may be damage to the machine gt Allow the descaling programme to run to the end If the descaling agent comes into contact with sensitive surfaces e g marble damage cannot be ruled out gt Clean up any splashes immediately The descaling programme lasts approximately 45 minutes JURA descaling tablets are available from stockists If you use a CLARIS Blue filter cartridge and this is activated you will not be prompted to descale mme pmo imme 37 5 Maintenance Precondition Decalcify machine is displayed Pp pi e 38 gt Press the P button Maintenance status 1 6 gt Press the Descale button Descale If you do not want to start descaling just yet press the t but ton The prompt Decalcify machine remains active gt Press the Next button Empty drip tray gt Empty the drip tray and coffee grounds container and put them back into the machine Pour descaling agent into water tank gt Remove and empty the water tank gt Completely dissolve the contents of one blister three JURA descaling tablets in a receptacle holding 500 ml of water This may take several minutes gt Pour the solution into the empty water tank and insert it into the machine Please press the Rotary Switch gt Remove the cappuccino frother gt Place a receptacle at least 500 ml under the connector of the cappuccino frother gt
42. ter 5 Maintenance Rinsing the cap puccino frother You can choose to use a second coffee variety for example decaf feinated coffee with the filler funnel for ground coffee 1 me Never add more than two level measuring spoons of ground coffee Use ground coffee which is not ground too finely Very fine coffee can block up the system so that the coffee only comes out in drips If you did not fill the machine with a sufficient amount of ground coffee Not enough ground coffee is displayed and the IMPRESSA stops the operation Permanently setting the amount of water for the cup size 2 Preparation i The desired speciality coffee must be prepared within approx imately one minute after filling with the ground coffee Oth erwise the IMPRESSA stops the operation and is once more ready for use All speciality coffees with ground coffee are prepared following this model Example Proceed as follows to prepare one espresso using ground coffee gt Place an espresso cup under the coffee spout gt Open the cover of the filler funnel for ground coffee Please add ground coffee gt Place one level measuring spoon of ground coffee into the filler funnel gt Close the cover of the filler funnel Please select product gt Press the Espresso button Preparation will now begin The preset amount of water for espresso flows into the cup Preparation stops automatically
43. the machine yourself Do not modify the machine in any way that is not described in these instruc tions for use The machine contains live parts If opened there is a danger of potentially fatal injury Repairs may only be car ried out by authorised JURA service centres using original Spare parts and accessories To completely and safely disconnect the machine from the power supply first switch off the IMPRESSA using the On Off Important information button and then at the power switch Only then should you remove the mains plug from the power socket There is a risk of scalds or burns on the spouts and the cappuccino frother Place the machine out of the reach of children Do not touch any hot parts Use the handles provided Ensure that the cappuccino frother is correctly fitted and clean If incorrectly fitted or if they become blocked the cap puccino frother or its parts might come off A defective machine is not safe and could cause injury or fire To avoid damage and any associated risk of injury or fire Never allow the mains cable to loosely hang down The mains cable could pose a tripping hazard or become damaged Protect the IMPRESSA from environmental influences such as rain frost and direct sunlight Do not immerse the IM PRESSA mains cable or connections in water Do not put the IMPRESSA or any individual parts in the dish washer Switch your IMPRESSA off at the power switch before any cleaning operation Al
44. tor gt Remove and empty the water tank Turn the Rotary Switch until 60 sec is displayed Steam will continue to be discharged from the connector until the system is empty Fill water tank gt Press the On Off button The IMPRESSA is switched off mm l Disposal Please dispose of old machines in an environmentally neutral way ni Old machines contain valuable recyclable materials which should be recycled Please therefore dispose of old machines via suitable collection systems 44 9 Technical data Voltage Power Safety test Energy consumption Save energy Active Energy consumption Save energy Inactive Pump pressure Holding capacity of water tank Holding capacity of bean container Holding capacity of coffee grounds container Cable length Weight Dimensions W XH xD Q Technical data 220 240 V 50 Hz 50 W Approx 5 Wh Approx 2 Wh Static max 5 bar 2 11 250 g Max 6 portions Approx 11m 10 9 kg 28 5 X34 2 x43 3 cm 45 0 Index 10 Index A Addresses 48 Automatic switch off 27 B Bean container Bean container with aroma preservation cover 4 Cleaning 39 Filling 9 Bus bar Technical data 45 Button On Off button 5 P button programming 5 C Cappuccino V Cappuccino frother Cleaning 33 Rinsing 33 CLARIS Blue filter cartridge Changing 34 Inserting and activating the filter 11 Cleaning Bean c
45. urn the Rotary Switch until the programme item Machine settings 1 4 6 is displayed gt Press the Save energy button Save energy Press the Active button Press the Save button Saved appears briefly on the display Machine settings 1 4 6 Press the P button to exit programming mode Please select product y y D vy By instructing your IM PRESSA to automatically switch itself off you can cut down your energy consumption If this function is activated your IM PRESSA switches off automatically after the preset time fol lowing the last action on the machine You can set the automatic switch off time to 5 minutes or 0 5 B hours Precondition Please select product is displayed P gt Press the P button Maintenance status 7 6 Turn the Rotary Switch until the programme item Machine settings 1 4 6 is displayed gt Press the Switch off after button Switch off after gt Press the lt or gt button to change the setting gt Press the Save button Saved appears briefly on the display Machine settings 1 4 6 P gt Press the P button to exit programming mode Please select product 27 4 Permanent settings in programming mode Unit for amount of water You can change the unit for the amount of water from ml to oz Example Proceed as follows to change the unit for the amount of
46. ways wipe the IMPRESSA with a damp cloth rather than a wet one and protect it from prolonged exposure to water splash Only connect the machine to the mains voltage in accordance with the information on the rating plate The rating plate is located on the underside of your IMPRESSA Further technical data is provided in these instructions for use see Chapter 9 Technical data Please only use original JURA maintenance products Use of products that are not explicitly recommended by JURA could damage the IMPRESSA Do not use any coffee beans treated with additives or caramel ised coffee beans Only fill the water tank with fresh cold water Switch the machine off at the power switch if you are going to be absent for a longer period of time Important information People including children who donot have the physical sensory or mental capabilities to use the machine safely or are inexperienced or lack knowledge in how to use the machine safely must be supervised by a responsible person when using it or must be instructed in how to use it correctly Safety when handling the CLARIS Blue filter cartridge m Filter cartridges should be kept out of the reach of children Store filter cartridges in a dry place in the sealed packaging Protect cartridges from heat and direct sunlight Do not use damaged filter cartridges Do not open filter cartridges 1 Preparing and using for the first time 1 Preparing and using f
Download Pdf Manuals
Related Search