Premier Mounts P4263F flat panel wall mount
Contents
1. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Premier Mounts intends to make this manual accurate and complete However Premier Mounts makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Premier Mounts makes no representation of warranty expressed or implied regarding the information contained herein Premier Mounts assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Premier Mounts 2010 Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 172. the PCB CSL1 locking mechansim and secure it using the supplied key Padlock Place the locking hook through the hole of the security barrel Snap lock and locking hook together PCB CSL1 Padlock Combination or Keyed Technical Specifications All measurements are in inches millimeters 33 25 845 q oooo0o000000000000000 C3 Carb CT eoo0o0000000000p000000 Co CEI rb Cr 10 Page 16 Visit the Premier Mounts website at http www premiermounts com Installation Instructions gt 4 P4263F z z PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor
3. E EER ASAE EER C ES even elites 6 Wood Stud Installation zsir aE aaae eera ERa se a rae aae aaa a aa aa itap taaa 6 Concrete Installation sssrinin orn esia eaan easan cen e gah aE EE Aaaah eaaa NEE Paea AENEA E EE EnEn Eana 8 Steel Studilnstallatioi s cie e aaae eect a er e E R E aaa ee aa T aO a EESE 9 Installing the Mounting Bracket resono n a e E E E coratecaah tesseeters 11 Selecting the Mounting HardWare vss mesier aariaa ada Dua di tence EE SEER EE OLETE EAT EEA EEEE AUREN 11 Universal Washer IMStallatiOMs oi2 c ce2 see ccseetes2s chs eeaeee ea a onus e A iae ss axes punedsurbubes aa EEE aAa a EEE NEE 12 Universal Spacer InstallatidM iesire nenene eane Naa oh R EEA En AEE AAE EE EEE E E N EA ONSE AEE NEEN EE ASE ENAERE EAEE a 12 Locking and Leveling Screw Installation ccccccccececceceeeceeeeeeeeeeeeaeaeeeeeegenaeceeegeeaaaeesesesesaeaeeeeseaaaeeeeesasaeaeaeeseeeeeaeees 13 Lock It Security Barrel Installation Optional ccccceceeeceeneeceeeceeee ce eeeeeceaeeeeeeseaaeaeeeeseceaaeeeeseceeaeeeesesesaeeeeeesecaeeeeeeseeseaeeeeees 14 Attaching the Mounting Bracket to the Flat Panel ecccccceececeececeeeeeeeaee sees sea aeeeeeeseceeeeeeeseceeeaeeeseseeaeeeeeeseeeeeeeeeees 14 Attaching the Flat Panel to the Wall Plate cccccecceceeceeeceeeeeeeee cece eeeaaeaeeeeseaaeaeeeeseseaeceeeseeeaeceeseseeaeaeeeeesenuaeeeeees 15 Mounting Bracket Adjustment iscri a Ea a Ea a eaa e a ia Erra a TE a REEE 15
4. ICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE STOP PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS At least two qualified people should perform the assembly procedure Personal injury and or property damage can result from dropping or mishandling the flat panel If mounting to wall studs or ceiling studs make sure that the mounting screws are anchored into the center of the wall studs or ceiling studs Use of an edge to edge stud finder is recommended A It is recommended that a maximum of plaster board be used when mounting to wooden studs Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires in wall Cutting or drilling into an electrical line may cause serious personal injury Make sure there are no water or natural gas lines inside the wall where the mount is to be located Cutting or drilling into a water or gas line may cause severe property damage or personal injury Thi
5. Leveling Screw AcjUStmie int icc ccs ses sone y esesecevesvees sdever eea E E E SEE Ta EE a ve a a e EEEE E Ea EENE iE 15 Locking SCHEW AGJUSUMENN aac cess sas eenen cesta ses de ee e a Eea aeaa aE deoe EE eede eNe OLEE E 15 Utilizing th Sec rity Barela a eaea E aE deans E E E E aa O ea a E E aE aeeai 16 Technical Sp citicati nS irrin reriratan eeadeceeeseu oi yecsheei dundee dds EREE ERETTE weasdteedeeeeectvedsecdecevencess wedges seeuedeeedend edeeineedinet atest 16 MV ANT AD UW psec ct cats ence states cteet cea ates chee aSccctecpetes a cassis scat ee guecceta vat aneteeapeaasiteseanieaseeatcuaticceatasac tsa atecsanseces 17 DISCIAUMC Mv des csc ovat carte ean eediy coecubeues ve et evens debeb sehen can oneayige ay abuts desei oases ctirsceaennanerews det aeshucie ond cues T 17 Weight Limit THE WALL STRUCTURE MUST BE CAPABLE OF AEE E E isan SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF a AE 15 S THE FLAT PANEL IF NOT THE WALL STRUCTURE MUST BE REINFORCED Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS MUST BE READ AND COMPLETELY UNDERSTOOD KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN MUST BE FOLLOWED AS OUTLINED TOP IN THESE INSTALLATION INSTRUCTIONS FAILURE TO DO SO COULD RESULT IN PROPERTY DAMAGE SERIOUS PERSONAL INJURY OR EVEN DEATH SAFETY MEASURES MUST BE PRACT
6. cation on the wall where you will be mounting your flat panel Use a stud finder to determine the exact center of each steel stud in the vicinity of the mounting location Use a pencil and mark the exact center of each steel stud Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 9 b 4 4 P4263F Installing the Wall Plate cont d Place the wall plate against the wall in the desired viewing location Adjust the wall plate to match the locations of the steel studs Level the wall plate Use a pencil and mark 2 upper and 2 lower locations where you will be drilling holes for the steel stud anchors Set the wall plate to one side in a safe location Use a power drill and 7 6 drill bit to drill a hole at each of the marks Insert a steel stud anchor into each hole If necessary lightly tap each steel stud anchor into place with a hammer Use a Phillips screwdriver to tighten each steel stud anchor screw until the legs have completely 4 7 compressed against the back of the steel stud C you first begin to turn it until the legs begin to compress The steel stud anchor screw will then turn easier for several turns The steel stud anchor screw will again feel tight when the legs have completely compressed against the back of the drywall Stop turning the steel stud anchor screw at that point A Do not overtighten the steel stud anchor scr
7. costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies
8. e Qty 2 Qty 1 000000000000 000 00000 EEE SS 0260006030088 003860 O SF 5 16 Flat Washers Universal Spacers Security Barrel Qty 6 Qty 24 Qty 1 Pro Mounting Hardware E zZ M6 Steel Stud Anchors Qty 6 5 16 Concrete Wedge Anchors Qty 6 5 16 x 3 Lag Bolts Qty 6 Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 3 gt 4 24 P4263F Parts List con d Page 4 M4 x 16mm Screw Qty 6 M4 x 25mm Screw Qty 6 M4 x 30mm Screw Qty 6 M5 x 16mm Screw Qty 6 M5 x 25mm Screw Qty 6 M5 x 30mm Screw Qty 6 M6 x 16mm Screw Qty 6 M6 x 25mm Screw Qty 6 M6 x 30mm Screw Qty 6 M6 x 45mm Screw Qty 6 Mounting Hardware M8 x 16mm Screw Qty 6 M8 x 25mm Screw Qty 6 M8 x 30mm Screw Qty 6 M8 x 45mm Screw Qty 6 M8 x 70mm Screw Qty 4 Visit the Premier Mounts website at http www premiermounts com Installation Instructions gt 4 P4263F Leveling Screws Allows for leveling adjustments of the flat panel after mounting Cable Electrical Cut Out A large cut out on the wall X plate allows for easy cable access and power U distribution installations Directional Mounting Arrow Directional Mounting Arrow lets you know which edge is up Low Pr
9. er and 2 lower mounting locations where you will be drilling holes for the concrete wedge anchors Each horizontal location cannot be closer than 12 apart Set the wall plate to one side in a safe location Use a power drill and 5 6 concrete drill bit to drill a hole at each of the marks Page 8 Visit the Premier Mounts website at http www premiermounts com Installation Instructions gt 4 P4263F eZ Installing the Wall Plate cont d Insert a concrete wedge anchor into each hole If necessary lightly tap each concrete wedge anchor into place with a hammer Remove the nuts and washers from all four 4 concrete wedge anchors Place the wall plate against the wall over the threaded shafts of the concrete wedge anchors Replace the washers which you removed from the concrete wedge anchors with the 5 6 washers shown in the parts list on Page 3 Attach the nuts and 4 washers to each of the concrete wedge anchors and tighten using a socket wrench and an M10 socket A Do not overtighten the wedge anchor nuts Proceed to the Installing the Mounting Bracket section Steel Stud Installation The supplied M6 steel stud anchors must be used to install your Premier Mounts mount to steel studs Do not use lag bolts or wood screws 5 Steel Stud Anchor Screw Steel Stud Anchor Sleeve Identify the general lo
10. ew Remove the steel stud anchor screws and set them aside itt The steel stud anchor screw will feel tight when washers You may leave them on the screw or discard them These small paper washers do not replace standard hs washers vin Steel stud anchors may come with small paper Page 10 Visit the Premier Mounts website at http www premiermounts com Installation Instructions Align the wall plate over the steel stud anchor sleeves Insert a steel stud anchor screw and a 5 6 washer into each steel stud anchor sleeve Use a Phillips screwdriver and tighten each steel stud anchor screw until it is just snug A Do not overtighten the steel stud anchor screws Do not use a power drill to tighten the steel stud anchor screws Proceed to the Installing the Mounting Bracket section Insert the Thread Depth Indicator into the thread inserts found on the bottom or top of the flat panel Use a pencil to mark the depth of the thread insert on the Thread Depth Indicator as shown in Figure 1 Insert the Thread Depth Indicator into the remaining thread inserts to compare and verify their depth Locate the correct diameter screw for the thread insert If the screw you selected is longer than the mark on the Thread Depth Indicator as shown in Figure 2 and Figure 3 do not use this screw The screw Marking the Depth length must not bypass
11. flat panel The locking screws consists of two 2 M6 x 120mm screws Thread one 1 locking screw into the bottom mounting hole on each of the mounting brackets Make sure the locking screw is securely threaded into the mounting tab before proceeding Do not thread the locking screw any further once it is even with the mounting tab Threading the Locking Screw Correctly Threaded locking screw any further will prevent you from safely attaching the flat panel to the wall plate Proceed to the Attaching the Mounting Bracket to the Flat Panel section gt Locking Screw Threaded Too Far Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 13 Lock It Security Barrel Installation Optional ty Optional security configurations include PCB CSL1 sold aay Padlock Combination or Keyed commercially available Please read the following directions to install the security barrel Remove the locking screw from the mounting bracket Place the locking screw into and through the security barrel See illustration below Re insert the locking screw and security barrel into the mounting bracket Tighten the locking screw and security barrel until seated in the mounting tab Do not thread the locking screw any further once it is even with the mounting tab see illustration to the right Threading the locking screw any further w
12. g three 3 mounting locations along the center of each wall stud Two people are recommended for this step one person to level the wall plate and another person to drill the pilot holes Drill a pilot hole in the center of each of the marks with a power drill and a 4 drill bit A Only use drill bit when drilling the pilot holes Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 7 gt 4 4 P4263F Installing the Wall Plate cont d Insert one 1 1 x 3 lag bolt and one 1 5 6 washer into each pilot hole Tighten all lag bolts using a socket wrench and 2 socket Do not overtighten the lag bolts when attaching the mount to the wall Improper installation may result in personal injury or property damage Proceed to the Installing the Mounting Bracket section Concrete Installation The supplied 5 6 concrete wedge anchors must be used for concrete installation You will need a 4 6 concrete drill bit which is available at your closest hardware store Concrete Wedge Anchors SY Example of 6 Concrete Drill Bit Not Included Two people are recommended for this step one person to level the wall plate and another person to mark the mounting locations Place the wall plate against the wall in the desired viewing location Level the wall plate Use a pencil and mark 2 upp
13. ill prevent you from safely attaching the flat panel to the wall plate A Do not overtighten the locking screw Proceed to the Attaching the Mounting Bracket to the Flat Panel section Locking Screw Lock It Security Barrel Attaching the Mounting Bracket to the Flat Panel This section presumes that you have read and understood these sections Selecting the Proper Mounting Hardware Universal Washer Installation Universal Spacer Installation Place your flat panel screen side down on a soft flat surface Identify the number and location of the thread inserts on the back of your flat panel Aligning the holes on each mounting bracket with the thread inserts on the back of your flat panel Secure each mounting bracket to your flat panel by inserting a minimum of two 2 screws per bracket A Do not overtighten the mounting hardware Proceed to the Attaching the Flat Panel to the Wall Plate section Page 14 Mounting Tab Visit the Premier Mounts website at http www premiermounts com P4263F Installation Instructions P4263F Attaching the Flat Panel to the Wall Plate A This section requires two people Do not Hakan pea flat panel until you are certain that top and bottom hooks of both mounting brackets are securely seated on the upper and lower mounting rails of the wall panel Raise the flat pa
14. nel past the top and bottom mounting rails on the wall panel Slide the flat panel down slowly keeping it close to the wall Engage the top and bottom mounting brackets to the rails of the wall plate Proceed to the Mounting Bracket Adjustments section Mounting Bracket Adjustments Leveling Screw Adjustment If your flat panel is tilted too far to one side the leveling screws will allow you compensate for this tilt by simply adjusting the screws with a screwdriver Loosen both locking screws Adjust the tilt of your flat panel Tighten both locking screws Caution It is possible to dislodge your flat panel while you level your flat panel Use extreme caution until you tighten the locking screws Locking Screw Adjustment After you have finished leveling your flat panel be sure to tighten the two 2 M6 x 120mm locking screws A Do not overtighten the locking screws M6 x 120mm Leveling Screw 1 per Bracket M6 x 120mm Locking Screw 1 per Bracket Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 15 gt 4 24 P4263F Utilizing the Security Barrel Your P4263F Mount includes one 1 Security Barrel which can provide additional theft deterrence for your flat panel PCB CSL1 Security Cable Thread the cable through the hole on the security barrel Attach
15. nels which have recessed or uneven mount points Each Universal Spacer adds to the distance between the mounting bracket and your flat panel The Universal Spacers must be stacked and oriented as shown The Universal Spacers must only be installed between the mounting bracket and your flat panel The Universal Spacers will fit M4 M5 M6 and M8 screw sizes Proceed to the Locking and Leveling Screw Installation section Page 12 Visit the Premier Mounts website at http www premiermounts com Installation Instructions P4263F ee Installing the Mounting Bracket contd Locking and Leveling Screw Installation Leveling Screw Installation You must install the leveling screws before you attach the mounting bracket to the back of the flat panel The leveling screws consists of two 2 M6 x 120mm screws Thread one 1 leveling screw into the top mounting hole on each of the mounting brackets Make sure the leveling screw is securely threaded into the mounting tab before proceeding P aeo ate i orrectly Threade Do not thread the leveling screw any further once it is even with the mounting tab Threading the leveling screw any further will prevent you from i Leveling Screw safely attaching the flat panel to the wall plate Threaded Too Far Locking Screw Installation You must install the locking screws before you attach the mounting bracket to the back of the
16. oceed to the Steel Stud Installation section Wood Stud Installation You must secure the wall plate to two 2 wall studs with a minimum of four 4 lag bolts 2 lag bolts for each stud found Use a stud finder to determine the exact center of wall studs in the vicinity of the wall plate Use a pencil to mark the exact center of each of the wall studs Two people are recommended for this step one person to level the wall plate and another person to mark the wall stud location Place the wall plate against the wall in the desired viewing location Adjust the wall plate to align the mount slots in the wall plate with the center of the wall studs Level the wall plate Use a pencil to mark the upper right mounting location along the center of the wall stud Page 6 Visit the Premier Mounts website at http www premiermounts com Installation Instructions gt 4 P4263F eZ Installing the Wall Plate cont d Drill a pilot hole in the center of the upper right mark using a 4 drill bit and power drill A Only use a drill bit when drilling the pilot holes Place the wall plate against the wall and align it with the pilot hole Insert one 1 5 4 x 3 lag bolt and one 1 hs washer into the upper right mounting hole and tighten using a socket wrench and 72 socket A Do not overtighten the lag bolt Level the wall plate Use a pencil to mark the remainin
17. oe PREMIER Cad MOUNTS CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS CCBSCCCCCCOCCCOCCCBOCOCOGCE f f CE COC OCOBCOCBOCCEGCCCECGE Universal Low Profile Flat Mount for 42 to 63 Flat Panels Model P4263F NORTH AMERICA EUROPE 3130 East Miraloma Avenue Swallow House Anaheim CA 92806 USA Shilton Industrial Estate USA and Canada Shilton Coventry England CV79JY Phone 1 800 368 9700 Phone 44 0 2476 614700 Fax 1 800 832 4888 Fax 44 0 2476 614710 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 U us 9531 203 C01 03 LISTED b 4 24 P4263F Weight Lirmit eera e EOE a EE E A A A eee eo neat a eee eee 2 Waming S lalemes een E sosce et oSdecm et reaessotseg eaesacsicstaenessc 2 Installation TOONS ws ici 3 sccesecccisccecdesuceveasi innana aena ana aR EAE woes EENE quslyn ah AAEE EEA EAN E SENSER AE EEAO NEEN EAL EKAR CEAN EEAO AAEN cas 3 Parts Liste oee eiea peee Eai aea reae nd AEE a ade Ea Ee r E E advices AE Ea e E ETa 3 Mounting Hardware eese E E i aacteesicugiatcessavsecteensaagcaemiseastcagereecsoess 4 E E E E E E E E E A L eens ade sevens E 5 Installing the Wall Plate WIMEOG CHOI s ss sant cas sete es ichcsnesceniecnnns dance giy ce tn eeny cave evens E A eben detaeaeeerse 6 Determining the Mounting Surface neeesser e EEEE te E Ea
18. ofile Design Holds the flat panel less than 1 from the wall 6B 5000000000003000006 Mounting Slots Allow for a variety of stud configurations and lateral shift adjustments when mounting your flat panel Locking Safety Screws Prevents the flat panel from being removed or dislodged from the wall plate TREO Universal Spacers Premier Mount s uniquely designed spacers that fit multiple screw sizes Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 5 b a 24 P4263F Installing the Wall Plate Introduction itt Directional Mounting Arrow To The Directional Mounting Arrow stamped into the top of the P4263F wall mount indicates which edge is the top Mounting Safety Two people are recommended to for the installation of this mount l000000000000000000000 C9 C1 rh C1 l000000000000000000000 CID Determining the Mounting Surface If you will be installing your P4263F mount to wood studs proceed to the Wood Stud Installation section If you will be installing your P4263F mount to a concrete wall proceed to the Concrete Installation section If you will be installing your P4263F mount to a steel frame pr
19. s product is intended for indoor use only Use of this product outdoors could lead to product failure and or serious personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com Page 2 Visit the Premier Mounts website at http www premiermounts com Installation Instructions gt A P4263F 24 Installation Tools The following tools may be required dependent upon your particular installation These tools are not provided by Premier Mounts but you can purchase them at your local hardware store 2 laal S v4 Drill Bit for 7 16 Drill Bit for k Electronic Stud Finder Wood Stud Steel Stud 5 16 Concrete Drill Bit Hand Held Drill Tape Measure Hammer as LA Protective Eyewear Socket Wrench 2 Socket Phillips Tip Screwdriver Optional tools for steel stud installations Optional tools for concrete installations Parts List Your Premier Mounts product is shipped with all proper installation hardware and components Make sure that none of these parts are missing and or damaged before beginning installation If there are parts missing and or damaged please stop the installation and contact Premier Mounts 800 368 9700 P4263F Universal Low Profile Flat Mount Assembly Components K r Mounting Brackets Wall Plat
20. the mark Threaded Insert Test each size of the screws provided Thread Depth Indicator The correct screws should thread easily into the mount point and not pull out when tension is applied Proceed to the Universal Washer Installation section Small Straw Small Straw or Toothpick or Toothpick Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 11 b a eZ P4263F Installing the Mounting Bracket contd Universal Washer Installation Premier Mounts Universal Washers are designed to accommodate the various M4 M5 M6 and M8 hole sizes required by flat panels Do not place excessive pressure on the back of the flat panel as this may damage your flat panel The Universal Washer must be installed between the head of the mounting screw and the mounting bracket as shown Does your flat panel have Recessed mount points Uneven mount points Acurved back Any obstruction near the mount point If Yes you must install Universal Spacers Remove the gt mounting brackets Universal Washers and mounting Mounting Screw screws from the back of the flat panel Proceed to the Universal Spacer Installation section Universal Washer If No skip to the Leveling and Locking Screw Installation section Mounting Bracket Universal Spacer Installation Premier Mounts Universal Spacers allow you to attach the mounting bracket to flat pa
Download Pdf Manuals
Related Search