Premier MVW46 flat panel wall mount
Contents
1. point downward Figure 3 Page 8 Visit the Premier Mounts website at http www premiermounts com Installation Instructions Full View Top Bottom View Side View The arrows show where the M8 x 16mm pan Phillips screws can go from inside to fasten MVW46s together Figure 1 If you are fastening multiple MVW46s use the M8 x 16mm pan Phillips screws provided to fasten them together from inside the frames Figure 1 To safely install rows of multiple MVW46s fasten them first in individual rows then fasten the rows together After that insert the heavy duty plastic tube Figure 2 An example of fastening multiple MVW46s in rows Figure 2 Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 9 gt 4 24 MVW46 Front View Closeup of MVW46 Slide the MVW46 to the desired position against Heavy Duty Stegl the tube Insert two 2 M8 x 10mm set screws into the corner screw holes above the tube Figure 1 Tighten the screws against the MVW46 and the tube Inside the MVW46 wrap and secure rigging flying Figure 1 hardware not included around the tube Figure 2 WARNING Rigging Flying Hard Do not install the rigging flying hardware or fly it the MVW46 s unless you are a qualified A V installation professional Heavy Duty Steel Tube inside the MVW46 Figure 2 All flat panel display e If you are installing a Samsung 460UT or _ MuStratonS are SNOWNI2. angle attach additional cables to the bottom of the frames and pull to the desired angle see drawing Re check all hardware and installation for proper tightness and security Pull additional cables at the bottom of the frames to adjust the tilt Technical Specifications All measurements are in inches mm om O O eee amen ae si Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 11 gt 4 24 MVW46 PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS
3. damaged stop the installation and call Premier Mounts at 800 368 9700 MVW46 Videowall Frame Qty 1 6mm Quick Release Button Qty 4 M8 Quick Release ae rea M8 x 10mm M6 x 30mm Pan Phillips y Button Qty 4 Set Screw Qty 4 Screw Qty 4 F M8 x 16mm Pan Phillips M8 x 20mm Pan Phillips Screw Qty 8 Screw Qty 4 Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 3 D 24 MVW46 The MVW46 Videowall Frame is designed for mounting the Samsung 460UT Samsung 460UT 2 NEC X461UN or NEC X461UN2 to Premier Mounts dual pole carts and stands or flying them from above They can be installed in either portrait or landscape orientation Quick release buttons make it easier than ever to install the displays which can be attached to the front and or back of the MVW46 You can join multiple MVW46s horizontally and or vertically to create a videowall 2 Cutouts Insert the tubing of Premier Mounts dual pole cart or stand and adjust the height of the MVM46 by tightening set screws 2 Corner Cutouts The corner cutouts can be used to insert 2 tubing for flying the MVW46 from above Outer Keyhole Mounting Slot Use these slots to Inner Keyhole quickly fasten the Alignment Tab Mounting Slot Samsung 460UT or Use these tabs to Use these slots to eee the MVW46 quickly align multiple quickly fasten the MVW46s next to NEC X461UN or each other NE
4. gt D PREMIER C4 MOUNTS CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS MVW46 Videowall Frame NORTH AMERICA EUROPE 3130 East Miraloma Avenue Anaheim CA 92806 USA Swallow House Shilton Industrial Estate USA and Canada Shilton Coventry England CV79JY Phone 1 800 368 9700 Phone 44 0 2476 614700 FaK 1 000 832 4888 Fax 44 0 2476 614710 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 9531 054 011 00 gt 4 24 MVW46 Contents COMENTS aaiae aa A A A A E a a aaa aeia 2 Warning Statements arreen rare EEE TE EEEE E EEE iii han eeetave 2 installation TOONS oane menen e are dont ccs eto A tes nsnadoadadndoyet dees eater nad 3 Pans iSto a A E E a a ais ails cs data eueetie ia abeneeeeas 3 FOU ROS eaea ue uacatan AE E tute aaanats a a aa e a a ee a N A AAA 4 Installing the MVWA4G csvisieiiii irisi risrnernerrirei enine Na EEEE EANAN EENEN E EE KEE EEEE EEEO TAEAKE EEEE E ERE 5 JEMROGUCTION ninia E a a a E a a aa a T a Aa 5 Dual Pol Cart Or Stand Installation sausras a a a a ae ae 5 Flying MStallation xermosiasrrsnn eresian ta EE EEOAE SEE NERODEN ENEE ENAERE TEASA EEEE EREE 8 Technical Specilications 2 sccsscciis ccgvidessc eceaedeiceatd ar A a n AA E A E A A Eaa 11 Waranty aissada aa aaa aAA aa Ra aA E pads ee gage redo sad e eE A E is 12 DiscdlaiMme n eese E E E E E E E staguade vevteatsanaeeeeti ais 12 Warning Statements Prior to the installation of th
5. C X461UN2 to the MVW46 Page 4 Visit the Premier Mounts website at http www premiermounts com Installation Instructions 4 MVW46 24 Installing the MVW46 Introduction The Premier Mounts MVW46 Videowall Frame is designed for use with Premier Mounts dual pole carts and stands as well as for flying from above You may use one MVW46 as a standalone mount or multiple MVW46s to create a videowall display Please read through the safety instructions before installation O Are you mounting the MVW46 to a cart or stand or flying from above If dual pole cart or stand continue to Cart Or Stand Installation below If flying from above go to Flying Installation on page 8 Dual Pole Cart Or Stand Installation Illustrations show only some of the installation configurations possible with the MVW46s Figure 1 Insert the tubing of the Premier Mounts dual pole cart s or stand s into the 2 circular cutouts of the MVW46 s depending on the installation Figure 1 ity Make sure the MVW46 keyhole mounting slots point down so that they can support the flat panel display s later Figure 2 The keyhole mounting slots should point downward Figure 2 Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 5 24 MVW46 Full View i Top Bottom View Side View The arrows show where the M8 x 16mm pan Phillips screws can go from inside to fasten MVW46s together Figure 1 If you
6. Or Samsung 460UT 2 attach four T a quick example purposes only release buttons and four 4 M8 x 20mm pan Phillips screws to the display s back mounting holes If you are installing an NEC X461UN or NEC X461UN2 attach four 4 universal spacers four 4 6mm quick release buttons and four 4 M6 x Omm pan Phillips screws to the display s back mounting holes Do not overtighten the screws Universal spacers are needed only for the NEC X461UN or NECX461UN2 to prevent its display handle from hitting the MVW46 Keyhole Mounting Slot Attach the flat panel display to either side of the MVW46 by inserting the display s quick release buttons into the keyhole mounting slots on the MVW46 locking them into place fe To align a videowall better attach the first flat i panel display in the lower left corner if the keyhole mounting slots point down left Q or attach it to the lower right corner if the keyhole mounting slots point down right 9 Then install the rest of the displays working clockwise fe The Samsung 460UT or Samsung 460UT 2 should i into the MVW46 s outer keyhole mounting slots he NEC X461UN or NEC X461UN2 should fit into the MVW46 s inner keyhole mounting slots Page 10 Visit the Premier Mounts website at http www premiermounts com Installation Instructions 4 MVW46 24 Rigging Flying Hardware Use the rigging flying hardware to safely suspend the MVW46 s overhead Toset the tilt
7. PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Premier Mounts intends to make this manual accurate and complete However Premier Mounts makes no claim that the information contained herein cov
8. are fastening multiple MVW46s use the M8 x 16mm pan Phillips screws provided to fasten them together from inside the frames Figure 1 itn To safely install rows of multiple MVW46s fasten them first in individual rows then insert the tubing of the dual pole cart or stand into each row After that fasten the rows together Figure 2 An example of fastening multiple MVW46s in rows Figure 2 Page 6 Visit the Premier Mounts website at http www premiermounts com Installation Instructions Slide the MVW4G6 to the desired height on the dual pole cart or stand Insert four 4 M8 x 10mm set screws into the MVW46 screw holes near the tubing see drawing Tighten the screws against the MVW46 and tubing Front View Closeup of MVW46 MG TOMM SEE SETEN All flat panel display e Ifyou are installing a Samsung 460UT or ils Halions are SROWEIOF Samsung 460UT 2 attach four 4 8mm quick example purposes only release buttons and four 4 M8 x 20mm pan Phillips screws to the display s back mounting holes If you are installing an NEC X461UN or NEC X461UN2 attach four 4 universal spacers four 4 6mm quick release buttons and four 4 M6 x Omm pan Phillips screws to the display s back mounting holes Do not overtighten the screws Universal spacers are needed only for the NEC X461UN or NEC X461UN2 to prevent their display handle from hitting the MVW46 Keyhole Mounting Slot Attach the flat panel display to eithe
9. ers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Premier Mounts makes no representation of warranty expressed or implied regarding the information contained herein Premier Mounts assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Premier Mounts 2010 Page 12 Visit the Premier Mounts website at http www premiermounts com Installation Instructions
10. is product these installation instructions must be read and completely understood Keep these installation instructions in an easily accessible location for future reference Videowall Tolerance Disclaimer Premier Mounts manufactures all videowall frames with a maximum tolerance of 0 015 inches between the mounting pattern and the frames outside perimeters Even though Premier Mounts provides different hardware options for precision alignments alignment issues may occur due to higher tolerance levels for display mounting patterns or the structural integrity of the mounting surface which may react to the total weight of the attached structure Proper installation procedure by a qualified service technician must be followed as outlined in these installation instructions Failure to do so could result in property damage serious personal injury or even death Safety measures must be practiced at all times during the assembly of this product Use proper safety SToP equipment and tools for the assembly procedure to prevent personal injury Premier Mounts does not warrant against damage caused by the use of any Premier Mounts product for purposes other than those for which it was designed or damage caused by unauthorized attachments or modifications and is not responsible for any damages claims demands suits actions or causes of action of whatever kind resulting from arising out of or in any manner relating to any such use attachments or
11. modifications At least two qualified people should perform the assembly procedure Personal injury and or property damage can result from dropping or mishandling your electronic equipment Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires on the floor Cutting or drilling into an electrical line may cause serious personal injury Do not install on a structure that is prone to vibration movement or chance of impact Failure to do so could result in damage to the flat panel and or damage to the mounting surface This product is intended for indoor use only Use of this product outdoors could lead to product failure and or serious personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com Page 2 Visit the Premier Mounts website at http www premiermounts com Installation Instructions MVW46 24 Installation Tools The following tools may be required depending upon your particular installation They are not included N l Heavy Duty Steel Tube 2 Phillips Tip Long Enough to Hang Screwdriver Tape Measure Level MVW46 s Parts List Make sure your Premier Mounts product has the following hardware and components before beginning installation If there are parts missing and or
12. r side of the MVW46 by inserting the display s quick release buttons into the keyhole mounting slots on the MVW46 locking them into place fe To align a videowall better attach the first flat dy panel display in the lower left corner if the keyhole mounting slots point down left Q or attach it to the lower right corner if the keyhole mounting slots point down right 9 Then install the rest of the displays working clockwise fe The Samsung 460UT or Samsung 460UT 2 should fit into the MVW46 s outer keyhole mounting slots The NEC X461UN or NEC X461UN2 should fit into the MVW46 s inner keyhole mounting slots Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 7 24 MVW46 Illustrations show only some of the installation configurations possible with the MVW46s If flying the MVW46 s insert a heavy duty steel tube not included into the frames upper 2 circular cutouts Figure 1 A Appropriate tubing and rigging hardware must be used to support a minimum of 4 times the combined weight of all the flat panel displays and MVW46s used The steel tube must be long enough to span the entire width of the frame s Figure 2 il Illustrations show only some of the installation configurations possible with the MVW46s Heavy Duty Steel Heavy Duty Steel Tube Tube 1 a MVW46s Figure 2 The keyhole mounting slots should
Download Pdf Manuals
Related Search