COCO Technology SUN-500
Contents
1. USER S MANUAL version 1 1 SUN 500 CURTAIN SUN BLIND SWITCH SUN 500 CURTAIN SUN BLIND SWITCH Picture of the AYCT 102 not included A Letter code selector B Number code selector C Terminal screws D Mounting tabs E Power wire terminals SUN 500 CURTAIN SUN BLIND SWITCH 1 Set the code switches to a desired number and 2 Switch off the mains power before you begin letter combination installation or removal of this product A The COCO transmitter e g remote control must be set to the same letter number code see the manual for the concerned transmitter SUN 500 CURTAIN SUN BLIND SWITCH 3 If applicable remove the existing unit with which you have controlled your rolling shutters sun blind curtains etc in the past A Ifan existing switch is replaced by the SUN 500 it can no longer be used 4 Connect 230 V mains power to the product 1 Connect the brown hot wire to terminal L and 2 connect the blue neutral wire to terminal N Tighten the clamping screws A The 230 V mains power must always be connected in the manner described above Your wire colours may be different If in doubt ask your installer SUN 500 CURTAIN SUN BLIND SWITCH Explanation The module contains 2 switches These terminals have no connection to the 230 VAC on F and N and are voltage free This makes it possible to switch low voltage motors without any problem In the2. 4 5 always returns to the rest position off Due to this automatic switching the SUN 500 can also be used as a timed switch Operation of the transmitter 1 Press the ON button sun blind raises 2 Press the ON button sun blind stops 3 Press the OFF button sun blind lowers 4 Press the OFF button sun blind stops If your sun blind lowers with the ON button and rises with the OFF button this is not a problem If desired however you can interchange the switch wires of the motors n terminals To prevent interference avoid placing multiple products close to each other The minimum distance between units should be approx 50 cm If you use multiple SUN 500 receivers that you want to control simultaneously the connected motors must have the same rotation direction for the raise and lower commands If the product does not work or does not work properly Check the batteries in the transmitter Make sure the letter and number combination of the SUN 500 matches that of the transmitter Switch the mains power off for 10 seconds to reset the SUN 500 Make sure there is no other receiver in the immediate vicinity Check whether there is too much wiring present near the SUN 500 or whether other metal objects may be causing interference SUN 500 CURTAIN SUN BLIND SWITCH Co JE A Safety instructions e Always switch off the mains power before you begin with installation or removal Switch the mains power on again once you are c
3. rest position the common contact COM is not switched After an on off signal from your COCO transmitter this switches either to the left or the right contact A built in timer always switches the COM contact back to the rest position after approx 2 minutes LL E 4 CODO dese 5 Connect the switch wires of the motor that drives your curtains or sun blind How this is connected is dependent on the situation and the type of motor you wish to control See the following instructions SA through 5D A If in doubt consult the supplier of your sun blind system SUN 500 CURTAIN SUN BLIND SWITCH 230V blue Earth yellow green 5A 230 V motors The motor has 4 wires earth yellow green neutral blue and 2 hot wires F1 brown and F2 black The position of F1 and F2 determines whether the blind is raised or lowered when the ON and OFF buttons are pressed on the COCO transmitter These two terminals can be interchanged without causing any problem 5B Low voltage motors e g 24 V The position of A and B can be interchanged without causing any problem A The L and N terminals must never make contact with the low voltage wires This can lead to dangerous situations and damage to the equipment SUN 500 CURTAIN SUN BLIND SWITCH Momentary switch 5C Motor with a momentary switch the motor has 2 wires For every command raise stop lower the same button on the transmitt
4. er must be pressed two times A The L and N terminals must never make contact with the switch terminals This can lead to dangerous situations and damage to the equipment 230V brown 230V blue 230V black 5D Two minute switching 230 V fan or stairwell lighting The SUN 500 can be activated with a switched COCO transmitter e g KCT 510 keychain with remote control or PIR 2050 motion detector and switches off automatically after approx two minutes SUN 500 CURTAIN SUN BLIND SWITCH 6 Install the product in a standard junction box or 7 Switch on all the power again other type of housing e g the motor housing Close the housing SUN 500 CURTAIN SUN BLIND SWITCH Leis Remarks A Reminders This product is a switch receiver and is intended to control motors for sun blinds rolling shutters mini blinds etc by means of a suitable COCO transmitter Only COCO transmitters on which a letter code house code is set manually are suitable to control the SUN 500 COCO transmitters that contain a pre programmed code part number begins with A are not suitable for this product The receiver only works with a 230 Volt power supply The internal switch contact of the SUN 500 is not connected to the 230 Volt mains power It is therefore possible to switch low voltage motors e g 12 of 24 Volt Approx 2 minutes after operation of the SUN 500 with a COCO transmitter the COM contact see Explanation between
5. light to pass through but has a negative impact on radio signals If there is HR glass between the transmitter and receiver you should expect a significant reduction of the range of the wireless signal e This product operates at a frequency of 433 92 MHz It complies with the essential requirements and other conditions of R amp TTE Directive 1999 5 EC and can be used in all EU countries e There may be restrictions on the use of this device outside the EU If this device is used outside the EU check whether the device complies with the local directives SUN 500 CURTAIN SUN BLIND SWITCH Leissoo This product complies with the essential reguirements and other relevant provisions of the applicable European directives The Declaration of Conformity DoC is available at www coco technology com A If possible submit this product for recycling after use Do not dispose of the product with household trash Warranty and copyright This device is covered by a 2 year warranty that begins on the day of purchase Visit www coco technology com warranty for additional information Reprinting of portions of this manual without permission from Pan Trade International B V is expressly prohibited SUN 500 CURTAIN SUN BLIND SWITCH PAN TRADE INTERNATIONAL B V t P O BOX 126 4760 AC ZEVENBERGEN THE NETHERLANDS www coco technology com Declaration of Conformity Pan Trade International BV declares that the COCO product model type designati
6. ompletely finished with the installation removal e This product is not intended to control doors Attention The wireless codes in this product can be cracked by third parties and this product has no protection against unintentional obstacles e g a person or car in the door opening The use of this product for doors is entirely at your own risk e Never connect more than one motor to the SUN 500 If you want to control multiple motors you must connect each motor to its own SUN 500 The power supply connected to the L and N terminals must be 220 240 Volts and 50 Hertz Do not connect any devices or lighting that consume more than 1000 Watts Incorrect connection of equipment can cause defects a short circuit and fire Do not expose this product to excessive heat direct sunlight or moisture Do not attempt to repair this product If the product is damaged or if you are in doubt about the proper operation take the product back to the place of purchase e Do not use the product in damp areas Clean the device with a clean cloth A Wireless e This product works using a radio signal that passes through walls windows and doors The range is maximum 75 metres in the open air The range indoors is strongly influenced by local conditions such as concrete glass and metals On average the indoor range is approximately 30 metres e New double glass often includes a thin metallic layer This type of glazing HR glass allows most visible
7. on SUN 500 CURTAIN SUN BLIND SWITCH item number 74016 is in compliance with the essential requirements and other relevant provisions of directives R amp TTE 1999 5 EC EMC 2004 108 EC and LVD 2006 95 EC and is compatible with the standards EN 300 220 1 3 EN 55015 EN 301 489 1 3 and EN 60950 Manufacturer Authorised representative AS M A Hoekstra managing director Zevenbergen 2008 01 30
Download Pdf Manuals
Related Search