Gastroback 41403 mincer
Contents
1. GASTROBACK __ Operating Instructions Design Mincer Plus Art No 41403 Design Mincer Plus Read all provided instructions before first use Model and attachments are subject to change For domestic use only Carefully read all provided instructions before you start running the appliance and pay attention to the warnings mentioned in these instructions Table of Contents Knowing your Design Mincer Plus ccecccceeeeceeeeeeeeeeeeeeeeeaeeeeeeueeeeeeaeeeeesaneeeegs 28 ORIG SCC QUIS 5 hes nsntnaccccuedet nine setwnansodaqadivedtttucntnanenawosn ghendesesege ppepbasseteeuend 29 Important safeguards for electrical appliances ccccceeccceeeeeceeseeeeeeeeeeeceaneeees 30 Moving parts risks Of injuries cccccccseeecceeeeeceeeseeeeesseeeeeseeeeeeaaeeeeesaeeeeaeaes 3 Technical SECT GOONS sias 25 02080 5aeievnicaiererceiannatansaslsnnmmnneunediudas ae basentuteoaanatieosiaeas 31 TORS MN SF US E E EEE EE ties coer A E E A E E 31 Properties of your Design Mincer Plus cccccssccccesececeeseeeeeeueeeeeeueeeeeeneeeeeuaeeeeens 32 Power switch overheat protection ocscwstendccdcrsatarnreaiaralodestveceedceteeneesuvencwamenet oa 32 The buttons ON OFF and REVERSE ccccecececececececececececacecucacucusaeacaeenes 32 TOS o A E E EE A E 33 Tips Tor besi resula eeren r r E EET 33 Per aE E E A E E RAEE 34 Assembling formin Ngere 34 Assembling for making sausages cccccseecceees2. Note When the worm housing is securely attached you can hear a click sound and the release button comes out of the recess again 3 Press the feed pan onto the worm housing pic ture G 4 Place the pusher into the opening of the feed chute picture H The appliance is ready for operation 36 z aN ww A e we a Assembling for making kebbe 1 Take the worm housing into the right hand and insert with your left hand the worm inside the worm housing picture I The side of the worm with the plastic end has to face the worm housing when put ting it inside the worm housing The worm is cor rectly assembled when the plastic end of the worm stands a few millimetres out of the worm housing Take the plastic finger The flat end with the recess has to face the worm housing when attaching If necessary turn the plastic finger a little bit until the arresting pin of the worm housing locks precisely into the corresponding recesses of the plastic fin ger IMPORTANT If the tools overlap the edges of the worm housing the worm is not placed all the way inside of the worm housing Turn the worm a little bit to make it fit inside but do not use force If mounted correctly the plastic finger is aligned with the front of the worm housing and the axis of the worm stands out 2 mm of the grinding disc Place the cone on the worm housing and fit the closure ring over the cone Firmly screw the closing
3. The purchaser has to present the sales slip in assertion of claim and has to bear all charges of costs and risk of the transport 46
4. cord before use Do not place the appliance on the power cord The power cord may never be knotted twisted pulled strained or squeezed Do not let the plug or power cord hang over 30 the edge of the table or counter The power cord may not touch hot surfaces Ensure that no one will pull the appliance by the power cord Take care not to entangle in the power cord Always grasp the plug to disconnect the power cord Do not touch the power plug with wet hands when the appliance is connected to the power supply e Do not place or immerse the motor housing or the power cord in water or any other liquid Do not spill or drip any liquids on the power cord or exterior of the motor housing When liquids are spilled on the motor housing or power cord immediately unplug and switch off ON OFF button and power switch the appliance Moving parts risks of injuries The mincer is suited for finely chopping food Thus moving parts of the appliance can cause severe injuries when used contrary to these instructions e Do not insert your hands hair clothes brushes or other foreign objects e g bones stalks of vegetables cooking utensils in the feed tube of the appliance or in the outlet of the cutter housing when the appliance is connected to the power supply Before connecting the appliance to the power supply always ensure that there are no foreign objects in the feed tube or cutter housing and the appliance is assembled completely and corre
5. feed tube When pro cessing larger amounts of food prepare the food in portions that can be processed within 2 or 3 minutes In between times switch off the mincer ON OFF button to let the motor cool down In the meantime you can prepare the next portion Cut meat and food of similar consistency in strips ca 10 cm in length and 2 cm thick Cut food that is somewhat firmer in 1 cm cubes at the maximum If the motor agitates too slowly and is about to get stuck cut your food to smaller pieces and or cook firm food e g vegetables before processing Slow down your work speed 33 Add onions and finely grinded spices while mincing the foods for getting an even mixture However hard spices e g pepper nutmeg etc must be grinded in a mill before proces sing with the mincer It is a good idea to fry onions for minced pork before processing This way onions are more flavoury and wholesome Operation WARNING The mincer is intended for mincing food For this the appliance is equipped with sharp edged knives and other electrically driven moving parts Do not insert your hands or any foreign objects e g cooking utensils in the feed tube or outlet of the cutter housing while the appliance is connected to the power supply to avoid risks of injuries Always switch off the ON OFF button first then unplug the appliance before assembling or disassembling any parts Before operation always ensure that you have assembled the
6. ring on the worm housing and tighten by hand __ ATTENTION Do not use any tools for tightening the screw and pay attention not to cant the screw If the screw cants the screw thread gets damaged If the screw does not turn easily put some sunflower oil or other edible oil on the screw 2 Firmly secure the worm housing in the opening for the drive shaft The small end of the worm hous ing has to face the mincer picture J Incline the worm housing a little bit to the right when assem bling it When the worm housing is fitted all the way into the opening of the drive shaft the release button sinks into the motor housing Turn the worm housing counter clockwise until the shaft is facing upright and is locked into place Note When the worm housing is securely attached you can hear a click sound and the release button comes out of the recess again 37 3 Press the feed pan onto the worm housing pic ture K 4 Place the pusher into the opening of the feed chute picture L The appliance is ready for operation Assembling for making cookies 1 Take the worm housing into the right hand and insert with your left hand the worm inside the worm housing Picture M The side of the worm with the plastic end has to face the worm housing when putting it inside the worm housing If the worm is correctly assembled when the plastic end of the worm stands a few millimetres out of the worm h
7. surface where it cannot fall Do not place any hard or hea vy objects on the appliance or any part of it Always handle the power cord with care Power cords may never be knotted twisted pulled strained or squeezed Do not use any parts or tools of the appliance for any other purpose than operating the appliance It is a good advice to store the parts and accessories of the appliance with the appliance 1 Always clean the appliance and its parts before storage see gt Care and cleaning 2 lt is good a advice to reassemble the cutter housing with cutter blade and a grinding disc before storage See Assembling the appliance lt to avoid injuries by the cutter blade 3 Additionally you can insert some tools in the pusher see picture Q For this remove the cover of the pusher and place the tools into the interior as shown in the figure Then insert the pusher in the feed tube of the cutter housing 4 Carefully roll up the power cord without knotting or bending it Then place the power cord in the cord compartment in the bottom of the motor housing CAUTION Do not carry the appliance by the tray or cutter housing To move the motor housing always grasp it at both sides near the bottom 5 Grasp the motor housing with both hands at its sides and place it and all parts and tools on a suitable surface where it cannot fall and is out of reach of young children A5 Notes for disposal et Dispose of the appliance and
8. Do not process food that is too juicy Dab dry before proces sing Clearing a blocking reverse operation CAUTION Do not operate the motor in reverse direction for more than a few seconds Reverse operation moves the foods to the motor housing Thus foods and juices could run into the gear hole of the motor housing If the blockage of the worm shaft is not cleared away after a short moment of reverse ope ration switch off the appliance via the ON OFF button and power switch then unplug and clean the appliance according to the instructions in chapter gt Care and Cleanings Reverse operation is only intended for loosening blocked foods in the worm shaft by moving the worm shaft in opposite direction for a short moment To activate reverse operation 1 First switch off the motor via the ON OFF button Reverse operation is only available with the motor switched off and the power switch on 2 Press and hold down the REVERSE button The reverse operation starts immediately In general to release stuck food in the cutter housing it is sufficient to operate the motor in reverse direction for just a moment 3 You can switch off the reverse operation of the motor any time by releasing the button If the motor gets stuck again or reverse operation does not work switch off the appliance completely ON OFF button unplug and clean the appliance according to the instructions in chapter gt Care and cleaning However if the problem p
9. WARNING Always switch off completely ON OFF button and unplug the appliance before cleaning Do not immerse the motor housing or power cord in water or other liquids or spill any liquids on the motor housing or power cord Do not place the appliance or any parts of it in an automatic dishwasher 3 Before first use and after a longer period of storage clean the appliance and all tools See gt Care and Cleaning Properties of your Design Mincer Plus CAUTION Do not operate the appliance continuously for more than 3 minutes If you wish to process larger amounts of food always make brakes in between times switching the appliance off to avoid overheating The appliance is not suited for grinding very hard very fibrous or watery foods Cook hard vegetables e g carrots and leave to drain and or cut to small pieces before processing with the mincer Do not process extremely watery foods e g some fruits Otherwise juice could run into the gear hole of the motor housing and cause damage to the motor Power switch overheat protection The appliance is equipped with a separate power switch for switching off the appliance completely The power switch is located at the bottom of the appliance With the power switch on and the appliance connected to the power supply the indicators of the operating buttons on top of the motor housing ON OFF and REY illuminate blue This appliance is equipped with an overheat protection that wil
10. appliance completely and correctly according to the instructions in this booklet and that there are no foreign objects in the feed tube Carefully remove hard uneatable parts of your foods e g bones gristle sinews seeds stalks hard shells completely before mincing Do not place clothes tissues or any other foreign objects on or under the appliance during operation Do not place the appliance over a power cord Only use the provided pusher with the appliance Do not use any hard or sharp edged objects e g forks knives to avoid damage to the appliance Do not cut your foods on the tray of the appliance Do not use violence WARNING The work space has to be easily accessible solid even dry and of suf ficient size The mincer should only be set up on a firm level work surface Never place the appliance close to the edge of the working area Ensure that the power supply cable does not hang down from the work surface as it could be easily pulled particularly by small children thereby causing serious accidents Do not put any cloth or napkins underneath the appliance to avoid endangering by fire and electric shocks Never place the appliance on paper towels or uneven working areas The air has to able to circulate IMPORTANT Always ensure that the plug is not connected to the power outlet before assembling or disassembling the appliance Place the mincer on a flat dry surface such as a table top Assembling for mincing 1 Ta
11. ctly Only use the provided pusher to push down the ingredients Do not push with violence to avoid that the mincer gets blocked e The edges of the cutter blade are very sharp Ensure not to get injured when handling the cutter blade e Do not hold your face over the feed tube while the motor is agitating because splinters could escape from the feed tube if you failed to see small pieces of bones or other hard parts e g stalks hard seeds stones while preparing the foods Do not push the food with your hands down the feed tube or poke in the feed tube Technical specifications Model Art No 41403 Design Mincer Plus Power supply 220 240 V AC 50 60 Hz Power consumption 350 W max locked motor power 1 500 W Length of power cord approx 1 2 m Weight approx 3 15 kg Dimensions width x depth x height approx 220 x 186 x 377 mm Before first use WARNING DO NOT let young children play with the appliance or any part of it or the packaging 1 Unpack the appliance and all accessories carefully and check that no parts are damaged or missing Tip The pusher is hollow and some tools may be stored in its interior Remove the cover of the pusher just lift it and take out the tools 31 2 Carefully remove all shipping materials and promotional materials but do not remove any warning labels or the model label Especially ensure that there are no foreign objects e g packaging in the interior of the appliance
12. de the mincer to dry off overrunning liquids 1 Cut the meat into stripes 10 cm long and 2cm wide that will fit in the feed chute and remove hard parts like bones shells or stems 2 Assemble the appliance as described in Assembling the appliance and place a plate or dish in front of the worm housing WARNING Always make sure that the mincer is turned off before plugging in the power supply 3 Plug the power supply cable into a mains socket and switch on the mincer WARNING Never hold your face or other body parts over the feed chute when the motor is running because little pieces of food could be thrown out of the feed chute Never push the food into the feed chute with your fingers or put foreign substances hair towels cutlery into the feed chute Always use the pusher for this purpose 4 Press the ON OF button to engage the appliance and place the prepared food onto the tray 5 Slowly feed the meat pieces into the feed chute and push down with the pusher Do not apply excessive force when pushing down the pusher Only use the pusher to press down the meat Never use your fingers IMPORTANT Operate in a slow and constant pace Do not try to rush the procedure by pushing down the meat with force This way the worm might get blocked and stops operat ing If no meat is coming out the worm housing even though there is still meat in the feed chute turn the mincer off pressing the on and off button first and then the power butt
13. e indicators are dark The motor does not work the buttons are illumina ted The reverse operation does not work The ON OFF button is illuminated blue The motor works too slow ly Juice drips from the cutter housing Possible Cause The appliance is not live The power switch is switched OFF The circuit breaker is activa ted The overheat protection swit ched off the appliance The cutter housing is blocked You cannot start reverse ope ration while forward operati on is switched on The cutter housing is blocked You push down the pusher too violently Too hard parts are still in the foods The food is too hard The food is too watery A2 Solution Insert the power plug in the power outlet Switch on the power switch Press the red button at the bot tom of the appliance Let the motor cool down See gt Overheat protection Switch to reverse operation for a moment See Clearing a blocking reverse operati on Switch off the ON OFF but ton This button must be illumi nated white to activate rever se operation Try again Switch to reverse operation for a moment See Clearing a blocking reverse operati on of Decrease the pushing pressure Remove any hard parts before processing your foods Only process foods that have a similar consistency as meat Cook hard vegetables before processing Cut the food in smaller pieces
14. e kebbe attachment and the crossed blade knife with the grinding disc 5 Process the wrapping mixture in the mincer with the attached chopper attachments The finished product will be one long wrapping Cut the wrapping into convenient seize 6 Freeze the wrapping shortly 7 Fill the wrapping with the filling mixture and fry the wraps with some olive oil until it has the favoured browning Making cookies 1 Prepare the pastry for your cookies according to your recipe Possibly place the pastry in the refrigerator for about 2 hour 2 Assemble the mincer for making cookies with separator disc cookie attachment and cookie former see Assembling for making cookies 3 Place the pastry on the tray of the mincer 4 Insert the plug of the mincer in the power outlet switch ON the appliance power switch and ON OFF button and then use the pusher to gently push the pastry into the feed tube 5 After processing your pastry switch OFF the appliance ON OFF switch and power switch Then unplug the appliance 6 Clean the appliance according to the instructions in section Care and Cleaning Always clean the appliance immediately after operation Do not leave any food dry on the appli ance 7 Bake the cookies according to your recipe Al Solving Problems If any problems occur during operation you will find solutions in the following table Addi tionally you can contact your vendor Problem The motor does not work th
15. e the adaptor disc The small end with the recess has to face the worm when attaching If necessary turn the adaptor disc a little bit until the arresting pin of the worm housing locks precisely into the corresponding recesses of the adaptor disc IMPORTANT If the tools overlap the edges of the worm housing the worm is not placed properly inside of the worm housing Turn the worm a lit tle bit to make it fit inside but do not use force If mounted correctly the adaptor disc is aligned with the front of the worm housing and the axis of the worm stands out 2 mm of the adaptor disc Place the sausage attachment on the worm housing and fit the closure ring over the sausage attach ment Firmly screw the closing ring on the worm housing and tighten by hand ATTENTION Do not use any tools for tightening the screw and pay attention not to cant the screw If the screw cants the screw thread gets damaged If the screw does not turn easily put some sunflower oil or other edible oil on the screw 2 Firmly secure the worm housing in the opening for the drive shaft The small end of the worm hous ing has to face the mincer picture F Incline the worm housing a little bit to the right when assem bling it When the worm housing is fitted all the way into the opening of the drive shaft the release button sinks into the motor housing Turn the worm housing counter clockwise until the shaft is facing upright and is locked into place
16. eeeeeseeeeeesseeeeeseeeeeesaeeeessaeeeenees 35 Assembling for making kebbe cccccccecccceesecece eee eeeeueeeeeseaeeeeesaeeeessaeeeeeaaes 36 Assembling for making cookies sssnnsssnnssinussrenssrinssrrnrsrrirssrirssrirssrrrssrrrs 38 NNE N Ne Cl er E E E EE E eeeeanae ves a eeonenee gt 39 ALEE EES e EE nee ee E E ET 40 akO KE DDE meaa E E EEE E E A 40 MOKO TOO lt are E EO E A E E EA 41 Solving Problem an ee te EE IEEE E ET E EE EE 42 Clearing a blocking reverse operation cccccceeecceeeeceeeeeceeeeeeeneeeeee nessa eeeenes 43 Overhedi proleclion ante ee Rene keen e E ne ee eee een ee EEN E 43 Cors and Cleanihg essere E eee eo eRe een en een ee eee ee 43 Disassembling the Appliance ws soe crrueantonduencsuvencauscwmamtoncuanaanjeauatosan cee nshoanrenae 44 Cleaning he Appliance ane nnn ee eee ek E E E r 44 E E E E E A E E E A 45 Molestar Dipo CU occ AA R 46 IIR MCI OR and STIG Sie oa ve sear E E E S 46 AN O E E E EE ee E 46 Dear Customer Congratulations A variety of new possibilities for delicious meals comes with your new min cer even for vegetarian dishes Effortless you mince and mix the ingredients for meatballs ve getable burgers and minced meat With great refinement you can prepare your own sausage specialities or fillings for ravioli or tortellini always really fresh These instructions for use will inform you about the various functions and features which makes it easy to take pleasure
17. er heater or oven Do not use any parts or tools of the appliance with any other device e Do not attempt to grind bones nuts or other hard items e Do not grasp in the gear hole of the motor housing with the appliance connected to the power supply e Do not leave the appliance unattended during operation Always switch off ON OFF but ton at first then unplug the appliance and wait until the motor comes to a standstill before moving or cleaning or assembling or disassembling any parts or when the appliance is not in use e Do not press the reverse button before the motor has completely come to a standstill e Always grasp the motor housing at both sides near the bottom for moving or lifting Do not hold the appliance at the tray or cutter housing for moving the appliance e Do not use any abrasive cleaners cleaning pads e g metal scouring pads or any corro sive chemicals e g bleach for cleaning Do not immerse the motor housing or power cord in water or any other liquid Do not spill or drip any liquids on the motor housing or on the power cord to avoid risk of fire and electric shock Do not pour any liquids in the feed tube with the cutter housing connected to the motor housing When liquids are spilled in the motor housing immediately unplug the appliance switch off the appliance completely ON OFF button and wait for the appliance to cool down Thereafter clean and dry the appliance thoroughly See gt Care a
18. ersists slow down working and cut your foods to smaller pieces before processing in the mincer Overheat protection This appliance is equipped with an overheat protection that will automatically shut off the appliance in case of overheating If your appliance suddenly stops running act upon the instructions Power switch overheat protection Slow down your work speed and use smaller portions Regularly switch off the appliance in between times for 15 minutes Please contact you vendor or an authorized service centre if the overheat protection is activated too often anyhow Care and Cleaning WARNING Do not insert your hands or any foreign objects in the feed tube or outlet of the cutter housing while the appliance is connected to the power supply The cutter blade is sharp edged Handle with care to avoid cutting your fingers Do not place or immerse the motor housing or power cord in water or any other liquids Do not spill any liquids on the motor housing or power cord Do not pour any liquids in the feed tube while the cutter housing is assembled to the motor housing Always disconnect the cutter housing from the motor housing before assembling or disassembling any tools or removing stubborn blockages Do not place the appliance or any part of it in an automatic dishwasher 43 Do not leave any food dry up on the appliance or any parts of it to prevent a build up of dried on foods Always clean the appliance after each
19. h four sets of tools e Cutter blade and two grinding discs for mincing and mixing e Separator disc and sausage horn for filling sausage skins with minced meat e Plastic finger and cone for making special meat p t kebbe e Cookie maker and former for preparing cookies CAUTION Always use only one matching set of tools For mincing and mixing only use one grinding disc at a time Select the grinding disc according to the consistency of your foods and your liking e Select the coarse grinding disc for firm foods and for making coarse sausages e Select the fine grinding disc for tender foods e To get a really fine consistency e g for kebbe process the foods several times begin ning with the coarse grinding disc Then use the fine grinding disc for the second or third run Example For steak tartar mince the meat with the coarse grinding disc twice Tips for Best Results Only process edible foods that are not off and not over stored Only use meat that is really fresh Additionally process meat directly before consuming or cooking it Even in the refri gerator chopped meat is highly perishable Do not process very hard very fibrous or too large pieces of food e g bones gristle thick sinews seeds nuts stringy stalks hard shells etc Cook hard vegetables and always remove any uneatable parts completely before processing the food Cut the food into suitable pieces that can be inserted effortlessly in the
20. he worm housing and tighten by hand ATTENTION Do not use any tools for tightening the screw and pay attention not to cant the screw If the screw cants the screw thread gets damaged If the screw does not turn easily put some sunflower oil or other edible oil on the screw 2 Firmly secure the worm housing in the opening for the drive shaft The small end of the worm hous ing has to face the mincer picture B Incline the worm housing a little bit to the right when assem bling it When the worm housing is fitted all the way into the opening of the drive shaft the release button sinks into the motor housing Turn the worm housing counter clockwise until the shaft is facing upright and is locked into place Note When the worm housing is securely attached you can hear a click sound and the release button comes out of the recess again 3 Press the feed pan onto the worm housing pic ture C 4 Place the pusher into the opening of the feed AN chute picture D The appliance is ready for operation Assembling for making sausages 35 P B z A 4 1 Take the worm housing into the right hand and insert with your left hand the worm inside the worm housing Picture E The side of the worm with the plastic end has to face the worm housing when putting it inside the worm housing The worm is correctly assembled when the plastic end of the worm stands a few millimetres out of the worm housing Tak
21. in your new mincer We hope that you will enjoy your new mincer Your Gastroback GmbH 27 Knowing Your Design Mincer Plus I J K L M N 0 P Q R A Pusher Tools accessories M Separator disc a H Coarse grinding disc N sausage horn C Cutter housing Worm 0 Plastic finger D Release button P Cone J Cutter blade E Motor housing K Fine orindina disc Q Cookie attachment F Reverse button REV i a 9 R Cookie former G ON OFF button 3 Important safeguards Carefully read all instructions before operating this appliance and save for further refe rence Do not attempt to use this appliance for any other than the intended use described in these instructions Any other use especially misuse can cause severe injuries or damage by electric shock moving parts heat or fire Any operation repair and technical maintenance of the appliance or any part of it other than described in these instructions may only be performed at an authorised service centre Please contact your vendor e This appliance is for household use only and not intended for use in moving vehicles or boats Do not operate or store the appliance in humid or wet areas or outdoors Any use of accessories attachments or spare parts not recommended by the manufacturer may result in damage and or injuries to persons e Check the entire appliance regularly for proper operation especially the power cord Do not operate the appliance when the appliance or any
22. ke the worm housing into the right hand and insert with your left hand the worm inside the worm housing Picture A The side of the worm with the plastic end has to face the worm hous ing when putting it inside the worm housing The e worm is correctly assembled when the plastic end n of the worm stands a few millimetres out of the w Ra A T i worm housing Take the cutter blade and attach it AA to the worm The rounded side of the blade must at face the worm when attaching it to the axis of the ba j worm Ensure the square opening of the cutter E a gt blade fits over the four cornered shaft of the worm hd A 34 WARNING The blades of the crossed blade knife are very sharp Pay attention when you han dle the crossed blade knife ATTENTION Never use the cutter blade and the grinding disc together with the attachments How to work with the attachments is explained further back in the instructions Mount the grinding disc on the cutter blade The arresting pin must lock precisely into the corre sponding recesses IMPORTANT f the tools overlap the edges of the worm housing the worm is not placed properly inside of the worm housing Turn the worm a lit tle bit to make it fit inside but do not use force If mounted correctly the grinding disc stands out approx 2 mm of the front of the worm housing and the axis of the worm stands out 2 mm of the grinding disc Firmly screw the closing ring on t
23. l automatically shut off the appliance in case of overheating If your appliance suddenly stops running T lmmediately unplug the appliance 2 Let the appliance cool down for 60 minutes 3 Connect the appliance to the power outlet 4 Press the ON OFF button to switch the appliance off 5 Press the power switch to turn on the appliance again 6 Now you can turn on the appliance with the ON OFF button Please contact you dealer of an authorized service centre if the overheat protection is acti vated too often The buttons ON OFF and REVERSE Using the operating buttons ON OFF and REVERSE you switch the motor on and off For processing your food generally use the normal forward operation controlled via the ON OFF button 32 The indicator of this button illuminates blue when the appliance is connected to the power supply and switched on via the power switch After pressing the button the motor starts wor king immediately The worm shaft moves the foods to the outlet of the cutter housing Do not let the motor work continuously for more than 3 minutes Usually during this time you have processed a tablet full of meat Thereafter switch off the motor for 15 minutes to let the motor cool down It is a good idea to use this time for preparing the next portion Reverse operation is only intended for loosening blocked foods in the worm shaft see Clea ring a blocking reverse operation Tools The appliance is provided wit
24. nd Cleaning lt e Do not place the appliance or any of its parts or tools in an automatic dishwasher e Do not leave any food dry on the appliance Always clean the appliance after each use to prevent a build up of baked on foods see gt Care and Cleaning lt Always keep the appli ance and the tools clean Important safeguards for electrical appliances The appliance is driven electrically Place the appliance near a suitable wall power socket to connect the appliance directly to a protected mains power supply with protective conductor earth ground connected properly Ensure that the voltage rating of your mains power sup ply corresponds to the voltage requirements of the appliance 220 240 V 50 60 Hz AC rated for at least 8 A The installation of a residual current operated circuit breaker r c c b with a maximum rated residual operating current of 30 mA in the supplying electrical circuit is strongly recommended If in doubt contact your electrician for further information In various foreign countries the specifications for power supplies are subject to incompatible norms Therefore it is possible that power supplies in foreign countries do not meet the requi rements for safe operation of the appliance Thus before operating the appliance abroad ensure that safe operation is possible e Do not to use any extension cords or multi socket outlets e Always handle the power cord with care Always completely unwind the power
25. on and work according to the instructions gt Trouble shooting guide 39 IMPORTANT Do not let the motor run permanently for longer then 3 minutes to avoid overheating After 3 minutes turn off the appliance and let the motor cool down before continuing operation In the case of overloading the motor the overheat protection will automatically cut off the power supply Act upon the instructions in Power switch overheat protection 6 As soon as the last bit is minced turn the appliance off ON OFF button and disconnect the appliance from the power outlet 7 Clean and disassemble the appliance right after use and make sure that no leftover food dries up on the appliance Work according to the instructions gt Care and cleaning Making sausages 1 Prepare the meat according to the instruction Operating Mincing meat Season the meat as desired 2 Assemble the sausage attachment according to the instruction Assemble for making sausages 3 Soak the sausage skin for 10 minutes in lukewarm water Slide the sausage skin over the sausage attachment 4 Place the seasoned and minced meat again onto the tray and turn on the appliance withe the ON OFF button Tip If the skin gets stuck to the sausage attachment wet it with some water 5 As soon as the last bit has run through the appliance turn the appliance off pressing the on and off button first and then the power button and unplug the appliance 6 Clean and disas
26. ousing Take the adaptor disc The small end with the recess has to face the worm when attaching If necessary turn the adaptor disc a little bit until the arresting pin of the worm housing locks precisely into the corresponding recesses of the adaptor disc IMPORTANT If the tools overlap the edges of the worm housing the worm is not placed properly inside of the worm housing Turn the worm a lit tle bit to make it fit inside but do not use force If mounted correctly the adaptor disc is aligned with the front of the worm housing and the axis of the worm stands out 2 mm of the grinding disc Place the cookie attachment on the worm housing The flat end has to face the worm housing when attaching Fit the closure ring over the cookie attachment Firmly screw the closing ring on the worm housing and tighten by hand ATTENTION Do not use any tools for tightening the screw and pay attention not to cant the screw If the screw cants the screw thread gets damaged If the screw does not turn easily put some sunflower oil or other edible oil on the screw 2 Firmly secure the worm housing in the opening for the drive shaft The small end of the worm hous ing has to face the mincer picture N Incline the worm housing a little bit to the right when assem bling it When the worm housing is fitted all the way into the opening of the drive shaft the release button sinks into the motor housing Turn the worm housing counter clock
27. packaging must be effected in accordance with the corresponding local regulations and requirements for electrical appliances and pa ckaging Please contact your local disposal company EE Do not dispose of electrical appliances as unsorted municipal waste use separate collection facilities Contact your local government for information regarding the collection systems available If electrical appliances are disposed of in landfills or dumps hazardous substances can leak into the groundwater and get into the food chain damaging your health and well being When replacing old appliances with new once the retailer is legally obligated to take back your old appliance for disposal at least for free of charge Information and service Please check www gastroback de for further information For technical support please contact Gastroback Customer Care Center by phone 49 0 4165 22 25 0 or email info gastroback de Warranty We guarantee that all our products are free of defects at the time of purchase Any demons trable manufacturing or material defects will be to the exclusion of any further claim and within warranty limits of the law free of charge repaired or substituted There is no warranty claim of the purchaser if the damage or defect of the appliance is caused by inappropriate treatment over loading or installation mistakes The warranty claim expires if there is any technical interference of a third party without an written agreement
28. part of it is likely to be damaged to avoid risk of fire electric shock or any other damage and or injuries to persons The appliance is likely to be damaged if the appliance has been subject to inadmissible strain e g overheating mechanical or electric shock or if there are any cracks excessively fray ed or melted parts or distortions or if the appliance is not working properly In this case immediately unplug the appliance and return the entire appliance including all parts and accessories to an authorised service centre for examination and repair e During operation keep the appliance in an appropriate distance of at least 10 cm on each side and 50 cm in front and above to furniture walls boards curtains and any delicate objects Before operation always ensure that the appliance is assembled properly and com pletely Solely use the appliance for processing edible food Immediately unplug the appli ance if there is any kind of malfunction or problem e g the motor gets stuck overheating e Operate the appliance on a well accessible stable level dry water resistant and suitable large table or counter Always keep the appliance and the table or counter clean and dry and wipe off spilled liquids immediately Do not place any clothes or tissue or other objects under or on the appliance during operation to avoid risk of fire electric shock and overhea ting Do not place the appliance over a power cord or near the edge of the
29. semble the appliance right after use and make sure that no leftover food dries up on the appliance Work according to the instructions gt Care and cleaning Making kebbe Ingredients for the filling 100 g mutton once or twice minced with the mincer VW tablespoon olive oil 1 tablespoon fine chopped onions Ve teaspoon grounded pimento Vp teaspoon salt 122 tablespoon flour Ingredients for the wrapping at least 450 g fatless meat of mutton calf or beef the most 150 200 g flour 1 teaspoon grounded pimento 1 teaspoon grounded nutmeg l pinch of chilli powder l pinch of pepper The consistency of the wrap is better if you use less flour and more meat 1 Prepare the filling Steam the onions Mince the meat once or twice with the mincer and then mix the ingredients 40 2 Prepare the wrapping Mince the meat for the wrapping 3 times in total For the first mincing procedure use the medium grinding disc then use the fine grinding disc After mix ing all the ingredients for the wrapping mince it one more time with the medium grinding disc 3 Unscrew the closing ring and take out the grinding disc and crossed blade knife Operate according to the instructions gt disassembling lt the appliance WARNING Do not cut yourself removing the crossed blade knife 4 Assemble the appliance this time using the kebbe attachments Refer to Assembling for making kebbe lt ATTENTION Never assemble the appliance with th
30. table or counter or on wet or inclined surfaces or where it can fall e This appliance is not intended for use by persons including children with reduced phy sical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children must be supervised to ensure that they do not play with the appliance or any parts of the appliance or the packaging Always keep the appliance where it is dry and clean and where young children cannot reach it Do not leave the appli ance unattended when it is in reach of young children or when the appliance is connected to the power supply Do not place any hard and or heavy objects on the appliance or any part of it Take care that no one will pull the appliance by the power cord e Do not use any hard sharp or edged objects e g knives forks with the appliance Only use the provided pusher for feeding food into the feed tube Do not handle the appliance or any part of it with violence e Do not let the motor work continuously for more than 3 minutes Always use only one mat ching set of tools to avoid damage See Knowing Your Design Mincer Plus lt For mincing 29 always use only one of the provided grinding discs Do not process bones nuts frozen foods or any other hard items e Do not place the appliance or any part of it on or near hot surfaces e g burn
31. use according to the following inst ructions Disassembling the appliance WARNING Always switch off the ON OFF button and power switch wait until the motor comes to complete standstill and unplug from power outlet before disassembling or cleaning the appliance T Switch off the ON OFF button and power switch wait until the motor comes to complete standstill and unplug from power outlet 2 Remove the pusher Then lift the tablet upwards to remove it 3 Grasp the cutter housing with one hand then press the release button near the gear hole in the front plate of the appliance See Knowing Your Design Mincer Plus lt 4 With the release button pressed unlock the cutter housing by turning it clockwise Then pull the cutter housing out of the motor housing 5 Unscrew the screw ring 6 Hold the cutter housing close over a plastic bowl or kitchen sink and carefully turn the cutter housing with the outlet downwards This way the parts within the cutter housing will fall out Possibly for this you must impress the gear of the worm shaft in the cutter housing Cleaning the appliance WARNING The edges of the cutter blade are very sharp Handle with care to avoid injuries Do not use any abrasive cleaners cleaning pads e g metal scouring pads or any corrosi ve chemicals e g bleach for cleaning the appliance or any parts of it to avoid damage to the surfaces Do not immerse the motor housing or power cord in water or an
32. wise until the shaft is facing upright and is locked into place 38 Note When the worm housing is securely attached you can hear a click sound and the release button comes out of the recess again 3 Press the feed pan onto the worm housing picture O Slide the cookie former into the cookie attachment and choose the desired cookie shape Ensure the handle is facing away from the attachment when sliding it in otherwise you cannot use the cookie shape that is the closest to the handle 4 Place the pusher into the opening of the feed chute picture P The appliance is ready for operation Mincing meat The mincer operates absolutely dependently and clean If any problems should occur while Operating act upon instructions gt Trouble shootings WARNING For the case that liquid runs over the mincer while operating turn the mincer off immediately and pull the plug Clean and dry the appliance according to the instructions Care and cleanings Tip If you use special mince recipes you can mix the ingredients for example steamed onions or spices with the meat before mincing This way the ingredients get mixed really well Use the medium grinding disc when making tartar and mince the ingredients twice IMPORTANT The mincer cannot mince hard or stingily ingredients for example bones nuts ginger If you use hard ingredients like onions or carrots you have to steam them before adding them to the meat Place a dry towel besi
33. y other liquid Do not spill or drip any liquids on the motor housing or on the power cord to avoid risk of fire and electric shock Do not use violence Do not place the appliance or any part of it in an automatic dishwasher 1 Clean pusher tablet cutter housing worm shaft and screw ring as well as any used tools with warm dish water and a nylon brush If there are any tools within the pusher take the tools out first Stubborn residues on the surfaces can be removed better by soaking in warm dishwater for some minutes 2 Moisture a clean cloth or soft sponge with a little warm dishwater and carefully wipe the exterior of the appliance and the power cord WARNING Always ensure that the appliance and all parts of it are out of reach of young children 3 Thoroughly dry the motor housing and all parts and let dry naturally for about half an hour out of reach of young children 4 lt is good advice to lubricate the grinding discs and cutter blade with some vegetable oil 44 Storage WARNING Always switch off completely ON OFF button and power switch unplug and clean the appliance and all its parts before storing see Care and Cleaning Ensure to store the appliance where it is clean dry a che and safe from frost direct sunlight and inadmissib le strain mechanical or electric shock heat mois ture and where it is out of reach of young children Place the appliance on a clean and stable
Download Pdf Manuals
Related Search