Micromega FM 10
Contents
1. CONNECTIONS Having verified that the ON OFF switch is on OFF position connect the mains lead provided to the rear of the unit and to the wall socket Connect the interconnect cable from the rear of FM 10 to your amplifier input Connect the Antenna input POWER UP You may now turn on FM 10 by switching the ON OFF switch located at the back of the unit The central LED lights up indicating that the unit is in Standby mode Press once on the STANDBY key of the unit The display indicates FM 10 TUNER FRONT PANEL e ROTARY CONTROL To access Frequency or Pre set selection e SELECT switch between Manual or Pre set operation e SCANNING To place the unit into automatic station search mode e MEMORY To store pre set stations e MONO Switches reception between Mono and Stereo e MODE To Switch between modes e STAND BY switch the unit in and out Standby mode A red LED located below the central rotary control illuminates when in Standby mode DISPLAY e On the left side the mode of operation Manual or Pre set Inthe middle the lock indicator e On the right side the frequency in MHz In RDS mode the name of the station on the full display MANUAL TUNING Manual tuning is useful when you already know the frequency of the desired station e Press once on SELECT FM 10 appears on the left side of the display indicating Manual mode e Turn the central rotary control to the des2. HD MICrOMeEGR OPERATING MANUAL FM 10 HD oD Dear Customer Thank you for purchasing FM 10 tuner This unit provides ease of use and sonics of the highest quality Please pay close attention to this instruction manual and read it fully before attempting to operate It is designed to ensure that you maximise your pleasure of FM 10 and familiarise you with its many unique functions CHECKING e Check that the carton has no damage Should you have any doubt about its condition please do not hesitate to contact your dealer UNPACKING e Very carefully remove the unit from the box taking care to preserve all the packing material In the unlikely event that your unit needs to be sent back to either your dealer or distributor it must be sent in the original packing material Failure to observe this will invalidate your warranty ACCESSORIES Upon opening the carton you should find the following accessories e Mains lead e Dipole Antenna MAINS VOLTAGE e Check that the mains voltage indicated on both the carton and the rear of the unit correspond to the local power supply lf you are in any doubt consult your dealer INSTALLATION In order to obtain the maximum performance of FM 10 it is important to follow the installation instructions Wherever possible we recommend that FM 10 is installed in an audio rack or other suitable furniture that provides sufficient ventilation
3. hipped back in its original packing or if the serial number has been modified or erased Warranty Certificate Dealer s Stamp Date of Purchase Serial Number AUDIS sarl 13 15 rue du 8 mai 1945 ZA de la Haie Griselle 94470 Boissy Saint Leger FRANCE TEL 33 0 1 4382 8860 FAX 33 0 1 4382 6129 INTERNET http Awww micromega hifi com
4. indicates then for 2 seconds You can activate this function at any time by following the same instructions as above FM 10 is now fully set up TECHNICAL DATA FM 10 Typical Audio Performance Wave range FM ives ee ai 87 5 108MHz Sensitivity at 75Q MOn0 260B S teas ine sale tastes pin wea cova eds dey saad de wen 1 1 Stee Os 50GB S Bis shia 45uV SEISCUVIT sede ah cee 6048 at 300kHz Stereo TAD ws i en he lt 0 7 0 54 30Hz 15kHz Power Supply ESSA 15W Fuse type T 160mA 250V Slow Blow T 315mA 130V Slow Blow Dimensions W x D x HMM 0 inne nena nennen 430 x 250 x 70 WIG IM 5 bea ass FE edna EA bs wp nbd ba ee td ee 4 2 kg WARRANTY This warranty will start from the date of purchase of the Micromega product Statutory warranty regulations apply in the country where the Micromega product was purchased In case of complaints please contact the dealer who supplied your Micromega product WARNING Warranty will be nulled if the unit is not s
5. ired frequency During operation of the central rotary control audio outputs will be muted FM 10 is factory preset with RDS function activated Two seconds after locking on the selected station the display will indicate the name of the station according to the RDS standard AUTOMATIC SEARCH SCANNING Automatic search scanning allows you to scan the frequency band upwards short press or downwards long press e Press on the SCANNING key short or long press depending upon the desired scanning direction FM 10 will start to scan until it finds the next station of sufficient strength whereupon the lock indicator will light During search the display indicates If this is not a desired station please repeat the operation PRESET STATIONS Through the pre set mode you can store and access up to 50 stations To store a station e Locate the station that you wish to store either by manual or scanning mode e Press once on the MEMORY key to open the memory The display will indicate the first available pre set ex P05 or P should the memory be empty D D ENNEN LH ar si is EHS e Select the desired pre set number from 01 to 50 with the central rotary control e Press the MEMORY key to store your selection Repeat this process to store your other selected stations Note Any station that you store to an existing pre set will automatically overwri
6. te the previous stored station Access to pre set stations e Press the SELECT key to access the pre set mode e The display will indicate the pre set number and the corresponding frequency e Turn the central rotary control to access the desired pre set number e In order to return to manual mode press the SELECT key MODE The MODE key allows you to set up FM 10 input sensitivity and to turn On or Off the RDS function e Press once on MODE The display indicates FM 10 is set for the best reception with a cable antenna If you are using an individual antenna it is recommended that you increase the input sensitivity of FM 10 During the 2 seconds while the display indicates e Press once on STANDBY The display indicates then This indication stays visible for 2 seconds while you can access the LEVEL indicator to find the best position for your antenna e During the period when ANTENNA is displayed press once on STANDBY The display indicates then Move the antenna until you obtain the strongest possible signal We recommend that you use a strong station for this purpose ex BBC RDS Mode FM 10 is factory preset with RDS activated If you do not wish to use this function you can de activate it In CABLE mode press twice on MODE In ANTENNA mode press 3 times on MODE The display indicates This indication stays visible for 2 seconds while you can press on STANDBY to de activate this function The dislay
Download Pdf Manuals
Related Search