Home

CyberPower OL8000RT3U uninterruptible power supply (UPS)

1. hl LI IP L1 E MC a i L2 IP L2 A2 l PSDR 2 2A Fuse Slow Blow 3 m Backfeed Se IND 4 AC L1 5 AC L2 Copyright 2011 CyberPower Systems Inc BASIC OPERATION POWER MODULE FRONT REAR PANEL DESCRIPTION 1 Power Button Power on Indicator Master ON OFF for the UPS Indicates that the UPS is on and supplying power 2 UPS Status Fault Replace Battery LED Indicator Indicates the status of the UPS whether is operating in Line Battery or Bypass Mode or the UPS has an internal fault and the battery need to be replaced 3 Multifunction LCD Readout Shows UPS status information settings and events 4 Function Buttons Scroll up scroll down select and cancel LCD menu 5 Input Circuit Breaker Provides input overload and fault protection 6 Power Cord OL6K Input Output Terminal Block AS Connect to utility power your equipment se NN ZON y L N SRK 7 Output Circuit Breaker La Provides output overload and fault protection gt z MEN Bey 8 Battery Backup amp Surge Protected Outlets NI N M V WTA Provides battery backup and surge protection They aX F QT WE ensure power is provided to connected equipment over a period of time during a power failure Allows the creation of load priorities to ensure that battery power reserves are transferred to specified outlets during a power outage The unit can be programmed to pro
2. 6 7 8 9 10 Range 10 10 10 15 10 20 15 10 15 15 15 20 Check Freq Volt Check Volt Only No Bypass Default Setting 208V 5 1 0 1 5 Check Freq Volt Disable Enable Disable ECO Mode V Range 15 V Range 10 for Enable V Range 10 Manual Bypass Disable Enable Disable Battery Test Activate None Audible Alarms Disable Enable Enable EBM Number 0 1 2 3 4 5 6 7 8 9 10 0 Wiring Fault Disable Enable Disable NCL Control Outlet On Outlet Off Outlet On Language English Espafol Spanish Fran ais French English Generator Mode Disable Enable Disable Communication Disable Enable Enable I P Power Fail Battery Low Summary Alarm Dry Relay Set I P Power Fail UPS On Bypass UPS Fail Converter Mode Converter Off O P Freq 50Hz O P Freq 60Hz Converter OFF Screen Saver Disable 1 Minutes 5 Minutes 5 minutes Clear Event Log Activate None Button OFF LOCK Disable Enable Disable Charger Function SBM Constant SBM 200V are derated by 20 208 V are derated by 10 for OL6000RT3U This function can t be set when Manual Bypass Generator Mode or Converter Mode is enabled UPS has no bypass when Generator Mode is enabled UPS has no bypass when Converter Mode is enabled This function can only be set before the UPS is on aaa SILENCING
3. Battery Module __ LxWxH 26x 17 x 5 2in 66 x 43 3 x 13 2cm _ Net Weight Power Module 53lbs 24Kg _ Net Weight Battery Module 167 2lbs 76Kg 171 6lbs 78Kg Safety Conformance Approvals CE UL 200V are derated by 20 208 V are derated by 10 for OL6000RT3U fios Multi Language Interface 19 Types of Read Out 20 Types of Function Setting 3 Event Logs LED Indicators Power On Blue Line Mode Green Battery Mode Yellow Bypass Mode Yellow Fault Red Replace Battery Red Audible Alarms Battery Mode Battery Low Overload UPS Fault Replace Battery Copyright 2011 CyberPower Systems Inc TROUBLE SHOOTING Problem Possible Cause Solution Warning O P Overload Load Over XXX Battery Mode Battery Low BAT Disconnected Battery Failure Replace Battery EPO OFF Wiring Fault Line Abnormal Output Short Over Temperature Coldstart Lock Autorestart Lock Bypass Forbidden Over Charge Charger Failure High O P V Low O P V Bus Fault Your equipment requires more power than the UPS can provide If the UPS is in Line Mode then it will transfer to Bypass Mode if the UPS is in Battery Mode it will shutdown Your equipment requires more power than the setting in the Power Management Software PowerPanel Business will allow UPS is operating on battery power UPS is operating on battery power and will be shutting down soon due
4. OFF VENTILATION OPENINGS AROUND THE HOUSING DO NOT CONNECT DOMESTIC APPLIANCES SUCH AS HAIR DRYERS TO UPS OUTPUT SOCKETS SERVICING OF BATTERIES SHOULD BE PERFORMED OR SUPERVISED BY PERSONNEL KNOWLEDGE OF BATTERIES AND THE REQUIRED PRECAUTIONS KEEP UNAUTHORIZED PERSONNEL AWAY FROM BATTERIES Copyright 2011 CyberPower Systems Inc UNPACKING Gi Input Output terminal block cover Only for OL8000RT3U 0L10000RT3U Tie plate 1 2 sets EN go i r Yea ey User s manual Register card Flat head screws M5X8L 8 2 sets Pan head screws M5X12L 12 2 sets Rackmount left rail 2 sets Rackmount right rail 2 sets a Plastic washers 8 2 sets Phone line Screw hole dust covers 10 2 sets Serial Interface Cable RS 232 PowerPanel Business Edition software CD Copyright 2011 CyberPower Systems Inc HARDWARE INSTALLATION HARDWARE INSTALLATION These versatile UPS systems can be mounted in a rackmount or vertical tower orientation This versatility is especially important to growing organizations with changing needs that value having the option to position a UPS on a floor or in a rackmount system Please follow the instructions below for the respective mounting methods SAFETY PRECAUTIONS CAUTION To prevent the risk of fire or electric shock only use the supplied hardware to attach the mounting brackets RACKM
5. conditions carefully before using the CyberPower OL6000RT3U OL8000RT3U OL10000RT3U By using the Product you consent to be bound by and become a party to the terms and conditions of this Limited Warranty and Connected Equipment Guarantee together referred to as this Warranty If you do not agree to the terms and conditions of this Warranty you should return the Product for a full refund prior to using it Who is Providing this Warranty CyberPower Systems USA Inc CyberPower provides this Limited Warranty What Does This Warranty Cover This warranty covers defects in materials and workmanship in the Product under normal use and conditions It also covers equipment that was connected to the Product and damaged because of the failure of the Product What is the Period of Coverage This warranty covers the Product for three years and connected equipment for as long as you own the Product Who Is Covered This warranty only covers the original purchaser Coverage ends if you sell or otherwise transfer the Product How Do You Get Warranty Service 1 Before contacting CyberPower identify Your Product model number the Purchase Date and each item of Connected Equipment 2 Email us at tech cpsww com or Call us at 877 297 6937 3 If your product requires warranty service you must provide a copy of your dated purchase receipt or invoice How Do You Open A Connected Equipment Claim 1 Call us at 877 297 6937 or w
6. provide certain warranty benefits regarding Connected Equipment under this Warranty loss of profits business interruption or loss of information or data NOTE Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you 6 The Product is not for use in high risk activities or with aquariums The Product is not designed or intended for use in hazardous environments requiring fail safe performance or for use in any circumstance in which the failure of the Product could lead directly to death personal injury or severe physical or property damage or that would affect operation or safety of any medical or life support device collectively High Risk Activities CyberPower expressly disclaims any express or implied warranty of fitness for High Risk Activities or with aquariums CyberPower does not authorize use of any Product in any High Risk Activities or with Aquariums ANY SUCH USE IS IMPROPER AND IS A MISUSE OF THE PRODUCT Where Can Get More Information The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded CyberPower is the warrantor under this Limited Warranty For further information please feel free to contact CyberPower at CyberPower Systems USA Inc 4241 12th Ave E STE 400 Shakopee MN 55379 call us at 877 297 6937 or send us an e mail message at claims cyberpowersyst
7. voltage or frequency of utility power is out of range Your attached equipment may have problems please remove them and check again Check the fan for operation and if the ventilation hole has been covered Plug into utility power for first time operation Press ON OFF button to turn on UPS Slide the Interlock Bracket to the right For the PDU or HW PDU only 1 Remove battery connector and check charger voltage 2 Contact CyberPower for repair 1 Shut down UPS and turn off input breaker 2 Contact CyberPower for repair CyberPower Systems Inc www cpsww com Entire contents copyright 2011 CyberPower Systems Inc All rights reserved Reproduction in whole or in part without permission is prohibited PowerPanel Business Edition and PowerPanel Personal Edition are trademarks of CyberPower Systems Inc Copyright 2011 CyberPower Systems Inc PRODUCT REGISTRATION CyberPower requests that you complete and return the Warranty Registration Card enclosed with the Product or register the Product at its website www cpsww com to establish that you are the Initial Customer of the Product and therefore entitled coverage under the Limited Warranty and the Connected Equipment Guarantee Registration is not required for coverage but note if you do not register your purchase you will be required to provide proof of purchase LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARNTEE Read the following terms and
8. 10KVA 60A 6 AWG 14 0 mm INPUT OUTPUT CONFIGURATION Hardwire the input output terminals as shown in the following diagram Wiring Wiring AWG AWG Mains Input ee Output L1 L2 PE Circuit Breaker e L1L2 PE ae g PFC Inverter STS Sune tan esr O SAFETY PRECAUTIONS CAUTION Input and Output circuit breakers must be OFF during the building installation CAUTION An additional two pole disconnect device is necessary during the building installation CAUTION Disconnected EPO will immediately shut down the logic circuit output of the UPS Wiring the EPO signal is optional CAUTION Local safety rules may require a separate external EPO to turn off output circuit breakers Refer to local wiring rules the EPO should use approved components Only for OL8000RT3U OL10000RT3U Step 1 Separate the top and bottom covers Step 2 Fix the bottom cover on the terminal block Loosen the four screws to separate the top and bottom covers Tighten the two screws to fix the bottom cover on the terminal block amp 24 NS A gp P D LN Ug KV EN L S A R _ S w A P Copyright 2011 CyberPower Systems Inc HARDWIRING THE INPUT OUTPUT TERMINALS Step 3 Input configuration Step 4 Output configuration Insert the input cable through the appropriate cable gland not included Insert the output cable through the appropriate cable gland not included Step 5 Fix the top cov
9. AUDIBLE ALARMS 1 Press any of four function buttons on the LCD module Note the alarm can not be turned off for a Battery Low condition This condition will still result in an audible alarm 2 Configure Audible Alarms as Disable on the LCD module and it will stop warning of any malfunction audibly MANUAL BATTERY TEST Configure Battery Test as Active on the LCD module and it will perform the Manual Battery Test Copyright 2011 CyberPower Systems Inc STRUCTIONS REMOTE CONTROL Step 1 Remove the Multifunction LCD Module Unscrew the right panel of the Power module Separate the right panel from the UPS Gently lift the LCD module out Reinstall the right panel Step 2 Connect the DB26 Cable Connect the DB26 cable from LCD module to the Remote Control Port on the front panel or rear panel as shown in the following figure H f l et SZS x SS 9 5 SAFETY PRECAUTIONS CAUTION CAUTION It must be done by qualified personnel Copyright 2011 CyberPower Systems Inc WALL MOUNTING INSTRUCTIONS Step 1 Remove the Multifunction LCD Module Unscrew the right panel of the Power module Separate the right panel from the UPS Gently lift the LCD module out Reinstall the right panel Step 2 Rotate the DB26 Connector of LCD Module Step 3 Connect the DB26 Cable Connect the DB26 cable from LCD module to the Remote Control Port
10. CyberPower Here Quality Value User s Manual OL6000RT3U OL8000RT3U OL10000RT3U CyberPower Systems USA Inc 4241 12th Avenue East Suite 400 Shakopee MN 55379 Phone 877 297 6937 Fax 952 403 0009 www CPSww com KO01 0000195 00 IMPORTANT SAFETY INSTRUCTIONS This manual contains important instructions Please read and follow all instructions carefully during installation and operation of the unit Read this manual thoroughly before attempting to unpack install or operate the UPS CAUTION The UPS must be connected to a grounded AC power outlet with fuse or circuit breaker protection DO NOT plug the UPS into an outlet that is not grounded If you need to power drain this equipment turn off and unplug the unit CAUTION The battery can power hazardous components inside the unit even when the AC input power is disconnected CAUTION The UPS should be placed near the connected equipment and easily accessible CAUTION To prevent the risk of fire or electric shock install in a temperature and humidity controlled indoor area free of conductive contaminants Please see specifications for acceptable temperature and humidity range CAUTION No User Serviceable Parts Risk of electric shock do not remove cover No user serviceable parts inside Refer servicing to qualified service personnel CAUTION Non lsolated Battery Supply Risk of electric shock battery circuit is not isolated from AC power source ha
11. In case of the risk of electric shock do not remove the top cover CAUTION The battery can energize hazardous live parts inside even when the AC input power is disconnected Copyright 2011 CyberPower Systems Inc INSTALLING YOUR UPS SYSTEM SYSTEM BLOCK DIAGRAM Input Line Mode Battery Mode p Bypass Mode gt HARDWARE INSTALLATION GUIDE 1 Battery charge loss may occur during shipping and storage Before using the UPS it s strongly recommended to charge batteries for four hours to ensure the batteries maximum charge capacity To recharge the batteries simply plug the UPS into an AC outlet 2 When using the included software connect either the serial or the USB cable between the computer and the corresponding port on the UPS Note If the USB port is used the serial port will be disabled They cannot be used simultaneously After connecting to either the USB port or the Serial port on the UPS a computer with the PowerPanel Business Edition Agent software installed can control the operating schedule battery test outlets as well as obtain UPS status information However other computers with PowerPanel Business Edition Client software can only obtain UPS status information via LAN connection 3 Connect your computer monitor and any externally powered data storage device Hard drive Tape drive etc into the outlets only when the UPS is off and unplugged DO NOT plug a laser printer c
12. LED INDICATORS UPS STATUS LED Indicators Color UPS Status Description ON OFF Blue UPS power is on ON LINE Green UPS is operating in Line Mode BATTERY ON Yellow UPS is operating in Battery Mode BYPASS Yellow UPS is operating in Bypass Mode Manual Bypass or ECO Economy Mode FAULT Red UPS has an internal fault See Trouble Shooting for additional information REPLACE BATTERY Red Battery will soon need to be replaced due to insufficient runtime LCD SCREEN UPS STATUS LCD Screen UPS Status Description Line Mode UPS is operating in Line Mode Battery Mode UPS is operating in Battery Mode Bypass Mode UPS is operating in Bypass Mode Manual Bypass UPS is operating in Manual Bypass ECO Mode UPS is operating in ECO Economy Mode BUTTON OPERATION Button Operation Description ON OFF Press this button to turn on or turn off UPS A Press this button to scroll up in the LCD menu v Press this button to scroll down in the LCD menu ENTER Press this button to select an option ESC Press this button to cancel or return to previous LCD menu Copyright 2011 CyberPower Systems Inc LCD SETUP FUNCTIONS MULTI FUNCTION LCD MAIN MENU Press Enter button to activate MAIN MENU MAIN MENU submenu Function Description Information Displays the UPS information Configure Displays the UPS settings that can be configured by the user Displays the 3 most recent events by event count time E
13. Name Displays the UPS Model Name PA ee NS Displays the present Date amp Time Next BAT Change XXX XXXX Displays the next Battery Change Date amp Time Copyright 2011 CyberPower Systems Inc LCD SETUP FUNCTIONS LCD EVENT LOG 3 Event Logs of UPS can be recorded 1 Press the ENTER bution to activate the MAIN MENU Press the 4 and W buttons to scroll to the Event Log option 2 3 Press the ENTER button to select the Event Log submenu 4 Press the A and W buttons to scroll through the Event Log submenu in the following table 5 Press the ESC button to return to UPS Status Event Log Submenu Description XXDXXHXXM without PowerPanel Business or RMCARD302 X 1 with PowerPanel Business or RMCARD302 Event Content MULTI LANGUAGE INTERFACE Users can configure 1 of the 3 available languages for display English Espanol Spanish Francais French 1 Press the ENTER button to activate the MAIN MENU Press the A amp and W buttons to scroll to the Configure option Press the ENTER button to select the Configure submenu Press the 4 and W buttons to scroll through the Language options Press the ENTER button to select the Language submenu So oP eS Press the amp and W buttons to scroll to the language that you want to select You may be p
14. OUNT INSTALLATION Step 1 Remove the internal battery trays from the Battery module See page 17 Step 2 Rackmount ears installation Attach the two rackmount ears to the Battery module using the provided screws MSX8L 8pcs Step 3 Rackmount rail Installation The rails adjust to mount in 48 cm 19 inch panel racks from 52 to 91 5cm 20 5 to 36 inches deep Select the proper holes in the rack for positioning the Battery module in the rack The Power module or the Battery module takes up position 1 through position 9 Step 4 Adjust rackmount rails to fit your rack Attach the rackmount rail to your rack with two M5X12L screws and two plastic washers at the front of the rack Located in position 1 amp position 6 Do not tighten the screws Adjust the rail size on the rail assembly of your rack Secure the rail to the rear of the rack with two M5X12L screws and two plastic washers Tighten all screws at the front and rear of the rail Once completed perform the same steps for assembling the other rackmount rail Place the Battery module on a flat stable surface with the front of the unit facing toward you Secure the Battery module to your rack with four M5X12L screws at the front of the rack Located in position 2 amp position 8 Mh mse Mf ri rii MMR position 8 Lf a position 2 Step 5 Place the internal battery trays back into the Battery module See page 17 Once completed perform th
15. UIPMENT Under no circumstances this unit should be used for medical applications involving life support equipment and or patient care CAUTION DO NOT USE WITH OR NEAR AQUARIUMS To reduce the risk of fire do not use with or near aquariums Condensation from the aquarium can come in contact with metal electrical contacts and cause the machine to short out CAUTION Do not dispose of batteries in fire as the battery may explode CAUTION Do not open or mutilate the battery released electrolyte is harmful to the skin and eyes CAUTION A battery can present a risk of electric shock and high short circuit current The following precaution should be observed when working on batteries 1 Remove watches rings or other metal objects 2 Use tools with insulated handles CAUTION The unit has a dangerous amount of voltage When the UPS indicators is on the units may continue to supply power thus the unit s outlets may have a dangerous amount of voltage even when it s not plugged in to the wall outlet CAUTION Make sure everything is turned off and disconnected completely before conducting any maintenance repairs or shipment CAUTION Connect the Protection Earth PE safety conductor before any other cables are connected WARNING Fuses To reduce the risk of fire replace only with the same type and rating of fuse DO NOT INSTALL THE UPS WHERE IT WOULD BE EXPOSED TO DIRECT SUNLIGHT OR NEAR A STRONG HEAT SOURCE DO NOT BLOCK
16. and tighten the two screws to fix battery cable Step 5 Use a power cord to plug AC input inlet of the battery module into a wall receptacle Step 6 Turn on the DC breaker of the Battery module BATTERY INPUT 240V are 4 a_i ajo BACK FEED PROTECTION S PLUGINTOA Hl WALL l RECEPTACLE Hyp Copyright 2011 CyberPower Systems Inc BASIC OPERATION CONNECTION 2 POWER MODULE WITH MULTIPLE BATTERY MODULES Step 1 Connect the 1st Battery module to the Power module using the instructions above Step 2 Turn off the DC breaker of the 2 Battery module Step 3 Loosen the two screws to remove the battery cable retention bracket of the 1st battery module Step 4 Use the output cable of the 2 4 Battery module to connect the 2 Battery module to the 1s Battery module Step 5 Rotate the battery cable retention bracket and tighten the two screws to fix battery cable Step 6 Use a power cord to plug AC input inlet of the 2 battery module into AC output outlet of the 1st Battery module Step 7 Turn on the DC breaker of the 2 Battery module o WONCITICAL ico gt E AN N y wy D Sellers acces ie ce I ano PLUG INTOA pii a RECEPTACLE Copyright 2011 CyberPower Systems Inc OPERATION INSTRUCTIONS FOR LCD MODULE rE LS ES BATTERY REPLACE ON LINE on BYPASS FAULT BATTERY
17. e same steps for the Power module CAUTION The Battery module must be installed below the Power module Copyright 2011 CyberPower Systems Inc HARDWARE INSTALLATION VERTICAL TOWER INSTALLATION Step 1 Rotate the Multifunction LCD Module Step 2 Attach the base stands Unscrew the right panel of the Power module Separate the right panel secure the tie bracket with the screws M5X8 4pcs Tighten the screws from the UPS Gently lift the LCD module out Rotate it to the tower M5X12 4pcs of the base stands rackmount ears onto the bottom of orientation Reinstall it for a tower configuration the power module and the battery module To HAN MN i ji wi mM al mi Step 3 Attach dust covers Insert dust covers into the rackmount ear screw holes that are not being used 7 ID TA l h ELECTRICAL INSTALLATION After completing the hardware installation of the UPS you are now ready to plug in the UPS and connect your equipment SAFETY PRECAUTIONS CAUTION Installation environment should be in a temperature and humidity controlled indoor area free of conductive contaminants Do not install this UPS where excessive moisture or heat is present Please see specifications for acceptable temperature and humidity range CAUTION Never install a UPS or associated wiring or equipment during a lightning storm CAUTION Do not work alone under hazardous conditions CAUTION
18. ear Load lt 5 at Non linear Load Crest Factor ECO Mode Voltage Regulation 10 15 Configurable UPS Outlets 2 L6 20R 2 L6 30R 3 L6 30R 1 Terminal block 60 O O O m Surge Protection IEC 61000 4 5 Level3 es CSCS C i dzr Phone Network Protection __ RJ11 RJ45 One In One Out Overload Protection Line Mode 105 125 Load for 1 min 126 150 Load for 10 sec Battery Mode 105 130 Load for 10sec 131 150 Load for 2 sec Short Circuit Protection UPS Output Cut off Immediately or Input Fuse Circuit Breaker Protection _ Specifications 20 12V 77 2AH7__ 2012V 9 0AH H__ Recharge Time Typically 4hours 5hws _ Sealed Maintenance Free Yes Hot Swappable Yes O amh D amh T 5 2 9 O T Multi Function LCD Readout that Supports Audible Alarms Environment Operating Temperature 32 F to 104 F 0C to 40 C Operating Relative Humidity 0 to 90 Non Condensing Management fay On Device Features Self Test Auto Charge Auto Restart Auto Overload Recovery id Connectivity Ports 1 Serial Port RS232 1 USB Port 1 Remote Control Port 1 Relay Out ig SNMP HTTP Capable 1 Expansion Port With optional SNMP card or RUCARD 302 Power Management Software _ PowerPanel Business Edition Physical Dimensions Power Module LxWxH 26x 17 x 5 2in 66 x 43 3 x 13 2cm Dimensions
19. ems com Copyright 2011 CyberPower Systems Inc Ct FCC Notice This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference that may cause undesired operation WARNING This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Shielded signal cables must be used with this product to ensure compliance with the Class A FCC limits nt Regulation uilleur du Canada This document is believed to be accurate but CyberPower reserves the right to change or correct the contents and does not assume any responsibility for omissions or errors Need Additional Help Feel free to contact our Tech Support department with installation troubleshooting or general product questions CyberPower Technical Su
20. er on the bottom cover Tighten the six screws to fix the top cover on the bottom cover Copyright 2011 CyberPower Systems Inc BACKFEED PROTECTION BACKFEED PROTECTION OPERATION 1 Ifthe Bypass circuit is shorted and the UPS is running in Line Mode or Battery Mode backfeed protection will be active and the external isolation device Magnetic Contactor will open 2 Save your data and perform a controlled shutdown 3 Contact CyberPower for repair WITHOUT BACKFEED PROTECTION CONFIGURATION 1 Hardwire the input terminals as shown in the following diagram 2 Do not remove the interconnection wires Jumper Jumper2 on Backfeed Protection Connector Mains L1 L2 PE UPS DE ae E OO PE IP L1 IP L2 1 PSDR 2 3 Le Backfeed Jumper 1 4 AC L1 Jumper2 e AC WITH BACKFEED PROTECTION CONFIGURATION 1 Customers should provide an external isolation device Magnetic Contactor which is upstream and outside the UPS and capable of supporting the UPS input current 2 Remove the interconnection wires Jumper1 Jumper2 on Backfeed Protection Connector 3 Hardwire the input terminals and Backfeed Protection Connector as shown in the following diagram 4 The external isolation device must be installed in the Mains path Mains UPS L1 L2 PE Al
21. o ensure good battery capacity and long battery life Maintaining a good battery charge will help prevent possible damage to the unit from battery leakage 9 The UPS has one USB port default and one Serial port that allows connection and communication between the UPS and any attached computer running the PowerPanel Business Edition Agent software The UPS can control the computer s shutdown during a power outage through the connection while the computer can monitor the UPS and alter various programmable parameters Note Only one communication port can be used at a time The port not in use will automatically become disabled or the serial port will be disabled if both ports are attached 10 EPO Emergency Power Off Port EPO ports allow administrators the capability to connect the UPS unit to customer supplied EPO switches These installations give operators a single access point to immediately power off all equipment connected to the UPS during an emergency 11 To avoid electric shock turn the unit OFF and disconnect the unit from utility power before hardwiring the UPS in out power cord The in out power cord MUST be grounded Copyright 2011 CyberPower Systems Inc HARDWIRING THE INPUT OUTPUT TERMINALS CHECK CIRCUIT BREAKER WIRING Check branch circuit breaker rating and wiring dimensions at following table UPS Capacity Branch Circuit Breaker Wiring AWG Wiring mm 6KVA 40A 10 AWG 5 5 mm 8KVA 50A 8 AWG 8 0 mm
22. on the front panel or rear panel as shown in the following figure Step 4 Mount LCD Module on the Wall Wall mounting hole D 10 D 5 13 8L To avoid electric shock turn off and unplug the unit before installing REMOTE CONTROL or WALL MOUNTING INSTRUCTIONS MAINTENANCE Storage To store your UPS for an extended period cover it and store with the battery fully charged Recharge the battery every three months to ensure battery life Battery Replacement Please read and follow the Safety Instructions before servicing the battery Battery replacement should be performed by trained personnel who are familiar with the procedures and safety precautions Make a note of the replacement Battery module number Safety Precautions CAUTION Only use replacement batteries which are certified by CyberPower Systems Use of incorrect battery type is an electrical hazard that could lead to explosion fire electric shock or short circuit CAUTION Batteries contain an electrical charge that can cause severe burns Before servicing batteries please remove any conductive materials such as jewelry chains wrist watches and rings Battery Installation CAUTION Do not open or mutilate the batteries Electrolyte fluid is harmful to the skin eyes and may be toxic CAUTION To avoid electric shock turn off and unplug the UPS from the wall receptacle before servicing the battery CAUTION Only use tools with insulated handles Do not lay
23. opier space heater vacuum paper shredder or other large electrical device into the UPS The power demands of these devices will overload and possibly damage the unit 4 To protect a fax machine telephone modem line or network cable connect the telephone or network cable from the wall jack outlet to the jack marked IN on the UPS and connect a telephone cable or network cable from the jack marked OUT on the UPS to the modem computer telephone fax machine or network device 5 Press the ON OFF switch to turn the UPS on The Power On indicator light will display when activated If an overload is detected an audible alarm will sound and the UPS will continuously emit two beeps per second For resetting the unit unplug some equipment from the outlets Make sure your equipment carries a load current within the units safe range refer to the technical specifications Control 40 70 aa Output LCD Module amp lt gt USB amp DBO E ETATEN ea Ss eee See 6 This UPS is equipped with an auto charge feature When the UPS is plugged into an AC outlet the battery will automatically charge even when the unit is switched off T To maintain an optimal battery charge leave the UPS plugged into an AC outlet at all times 8 Before storing the UPS for an extended period of time turn the unit OFF Then cover it and store it with the batteries fully charged Recharge the batteries every three months t
24. pport Phone 1 877 297 6937 Email tech cpsww com Web www CPSww com Mail 4241 12th Avenue E Suite 400 Shakopee MN 55379 Hours of Operation Monday Friday 8 00am 5 00pm CST Entire contents copyright 2011 CyberPower Systems Inc All rights reserved Reproduction in whole or in part without permission is prohibited Copyright 2011 CyberPower Systems Inc
25. r will refund to you the full purchase price you paid for the Product purchase receipt showing price paid is required lf it appears that our Product failed to protect any equipment plugged into it we will also send you forms for making your claim for the connected equipment We will repair or replace the equipment that was damaged because of the failure of our Product or pay you the fair market value NOT REPLACEMENT COST of the equipment at of the time of the damage We will use Orion Blue Book or another a third party valuation guide or eBay craigslist or other source to establish that amount Our maximum liability is limited to 300 000 for OL6000RT3U OL8000RT3U OL10000RT3U Copyright 2011 CyberPower Systems Inc LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARNTEE Who Pays For Shipping We pay when we send items to you you pay when you send items to us What Are Some Examples Of What This Warranty Does Not Cover 1 This Warranty does not cover any software that was damaged or needs to be replaced due to the failure of the Product or any data that is lost as a result of the failure or the restoration of data or records or the reinstallation of software 2 This Warranty does not cover or apply to misuse modification operation or storage outside environmental limits of the Product or the equipment connected to it nor for damage while in transit or in storage nor if there has been improper operation or maintenance or use
26. rite to us at Cyber Power Systems USA Inc 4241 12th Ave E STE 400 Shakopee MN 55379 or send us an e mail message at claims cpsww com for instructions within 10 days of the occurrence 2 When you contact CyberPower identify the Product the Purchase Date and the item s of Connected Equipment Have information on all applicable insurance or other resources of recovery payment that are available to the Initial Customer and Request a Claim Number 3 You must provide a dated purchase receipt or other proof of the original purchase and provide a description of the damage to your connected equipment 4 Pack and ship the product to CyberPower and if requested the item s of Connected Equipment a repair cost estimate for the damage to the Connected Equipment and all claim forms that CyberPower provides to you Show the Claim Number on the shipping label or include it with the product You must prepay all shipping costs you are responsible for packaging and shipment and you must pay the cost of the repair estimate How Long Do Have To Make A Claim All claims must be made within ten days of the occurrence What Will We Do To Correct Problems CyberPower will inspect and examine the Product lf the Product is defective in material or workmanship CyberPower will repair or replace it at CyberPower s expense or if CyberPower is unable to or decides not to repair or replace the Product if defective within a reasonable time CyberPowe
27. rompted to save the selection if so press the ENTER button to save the setting 7 Press the ESC button to cancel or return to previous LCD menu LCD SETTINGS CONFIGURATION There are 20 UPS settings that can be configured by the user 1 Press the ENTER button to activate the MAIN MENU 2 Press the A amp and W buttons to scroll to the Configure option 3 Press the ENTER button to select the Configure submenu 4 Press the A amp and W buttons to scroll to the Configure submenu in the following table 5 Press the ENTER button to select the setting you want to configure The first configuration parameter will be displayed on the second column of LCD screen 6 Press the A amp and W buttons to scroll through the different parameters 7 Press the ENTER button to select the parameter you want to change You may be prompted to save the selection if so press the ENTER button to save the setting Some options are saved and started automatically See the following table for additional details 8 Press the ESC button to cancel or return to the previous LCD menu Copyright 2011 CyberPower Systems Inc LCD SETUP FUNCTIONS Configure Submenu Output Voltage Sync Freq Window Bypass V Window Bypass Condition Available Settings 200V 208V 220V 230V 240V Range 1 2 3 4 5
28. spike lasting longer than 1ms has occurred the occurrence will be deemed outside the rated capabilities of the Product and the Limited Warranty is void CyberPower Does Not Cover or Undertake Any Liability in Any Event for Any of the Following 1 Loss of or damage to data records or software or the restoration of data or records or the reinstallation of software 2 Damage from causes other than AC Power Line Transients spikes or surges on properly installed grounded and code compliant 120 volt power lines in the United States and Canada transients surges or spikes on standard telephone land lines PBX telephone equipment lines or Base 10T Ethernet lines when properly installed and connected This exclusion applies for example to fluctuations in data transmission or reception by CATV or RF transmission or fluctuations or by transients in such transmission 3 Damage from any circumstance described as excluded above with respect to the Product 4 Damages from fire flood wind rain rising water leakage or breakage of plumbing abuse misuse or alteration of either the product or the Connected Equipment 5 CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment Guarantee CyberPower excludes any liability for direct indirect special incidental or consequential damages whether for damage to or loss of property EXCEPT FOR AND ONLY FOR the specific limited agreement of CyberPower to
29. tandard RJ 45 RJ 11 Prevents power feedback from the inverter to utility power in case of power failure and a based products ADSL LAN Phone Modem Lines and fault in the bypass circuit cabling systems from surges Copyright 2011 CyberPower Systems Inc BASIC OPERATION BATTERY MODULE FRONT REAR PANEL DESCRIPTION 1 On board Replaceable Fuse Cover Replaceable fuse is accessible from the rear panel It must be done by qualified personnel 2 AC Circuit Breaker Provides overload and fault protection 3 AC Output Outlet Use this outlet to connect to the AC Input Inlet of a downstream Battery module 4 AC Input Inlet Charge Only AC power connectivity to wall receptacle 5 Input Connector Use this input connector to daisy chain the next Battery module Remove the connector cover for access 6 Output Cable Use this output cable to connect the Battery module to the Power module or to the next Battery module 7 DC Breaker BP240V30ART3U BP240V50ART3U Use the DC breaker to disconnect battery output CONNECTION 1 POWER MODULE WITH ONE BATTERY MODULE Step 1 Turn off the DC breaker of the Battery module Step 2 Loosen the two screws to remove the battery cable retention bracket of the power module Step 3 Use the output cable of the Battery module to connect the Battery module to the Power module Step 4 Rotate the battery cable retention bracket
30. to extremely low battery voltage Missing battery power UPS has failed in Battery Test Battery will soon need to be replaced due to insufficient runtime Missing the EPO connection Line and neutral wires are reversed Missing ground wire No ground wire Wrong utility power backed up during UPS auto restart Output short circuit High ambient temperature UPS is locked to prevent consuming battery power during shipping Automatic Restore is disabled in Power Management Software PowerPanel Business Manual Bypass Forbidden when the LCD screen shows Generator On or Converter On Battery is overcharged Charger has failed Output voltage is too high Output voltage is too low Internal DC bus voltage is too high or too low Shut off non essential equipment If this solves the overload problem the UPS will transfer to normal operation Shut off the non essential equipment or increase the level in the Power Management Software Save your data and perform a controlled shutdown UPS will restart automatically when acceptable utility power returns Check battery connector and battery breaker 1 Check battery connector and battery breaker 2 Contact technical support to replace the battery Contact technical support to replace the battery Check the EPO connection Exchange line and neutral wires Connect ground wire Disable Wiring Fault alarm on LCD panel Check whether
31. tools or metal parts on top of the UPS or battery terminals Replacement Batteries Please refer to the front side of the Battery module for the model number of the correct replacement batteries For battery procurement log onto www CPSww com or contact your local dealer Battery Disposal Batteries are considered hazardous waste and must be disposed of properly Contact your local government for more information about proper disposal and recycling of batteries Do not dispose of batteries in fire Step 1 Remove the front panels the cover itself Step 2 Remove the retaining screws from the cable protection cover and then remove Step 3 Pull the battery trays out slowly and then put the new battery trays back into the compartment Step 4 Insert the battery connectors and tighten the screws of battery retaining cover Step 5 Install the front panels Copyright 2011 CyberPower Systems Inc TECHNICAL SPECIFICATIONS Capacity vA dT 6ooova amp aooovA 10000VA 1 S I W Rackmount Tower Energy saving Technology Yes ECO Mode Efficiency gt 95 120 139Vac for 0 25 Load 140 159Vac for O 50 Load 160 179Vac for O 75 Load Input Voltage Range 180 280Vac for 0 100 Load Input Power Factor o S O Yes 200 208 220 230 240Vac Configurable 2 50 60Hz Auto Sensing or Configurable 0 25Hz Transfer Time Typically Oms Rated Power Factor Harmonic Distortion THD lt 3 at Lin
32. vent Log day hour minute and event description LCD INFORMATION READOUT There are 19 types of UPS information available for display 1 Press the ENTER bution to activate the MAIN MENU Press the A and W buttons to scroll to the Information option 2 3 Press the ENTER button to select the Information submenu 4 Press the A amp and W buttons to scroll through the Information submenu in the following table 5 Press the ESC button to return to UPS Status Information Submenu Description O P Volt XXX XV Displays the Output Voltage O P Freq XX XHz Displays the Output Frequency I P Volt XXX XV Displays the Input Voltage I P Freq XX XHz Displays the Input Frequency O P Load XXX Displays the Output Load Percentage of Maximum load O P Amp X XA Displays the Output Current O P Watt XXXXXW Displays the Output Wattage O P VA XXXXXVA Displays the Output VA BAT Volt XXX XV Displays the Battery Voltage BAT Cap XXX Displays the Estimated Percentage of Battery Capacity BAT Runtime XXXM Displays the Estimated Battery Runtime in Minutes EBM Number X Displays the External Battery Module Number Displays the Approximate inside Temperature in both C Celsius and F TEMP XX C XXX Fahrenheit for the UPS SBM XXXXX Displays the Stage of Smart Battery Management Rating XXK VA Displays the UPS Rating MCU Ver XXXX Displays the MCU Firmware Version Model
33. vide additional runtime for equipment connected to the CRITICAL outlets while stopping the power supply to equipment connected to NONCRITICAL outlets after a designated period of time Critical Noncritical Load 5 6 8 7 i 15 PTT 3 i Sho eS oalicuct 9 Serial Port E of H f Serial port provides communication between the UPS and rub ale HoH ek the computer The UPS can control the computer s Sour 00 shutdown during a power outage through the connection while the computer can monitor the UPS and alter its various programmable parameters 13 Relay Output Connector Convert UPS signals into real potential free Dry Contacts for industrial control OL8KRT3UPM OL10KRT3UPM 10 USB port This is a connectivity port which allows communication 14 SNMP HTTP Network slot and control between the UPS and the connected computer Slot to install the optional SNMP card for remote network control and monitoring It is recommended to install the PowerPanel Business Edition Agent software on the PC Server connected with 15 Extended Runtime Battery Module Connector the USB cord Connection for additional CyberPower XL Battery modules 11 Remote Control Port 16 EPO Emergency Power Off Connector Connects to remote LCD module to the UPS Enables an emergency UPS Power Off from a remote location 12 Surge Protected Communication Ports RJ 45 Ru 11 17 Backfeed Protection Connector These ports are used to protect s
34. with items not designed or intended for use with the Product such as laser printers appliances aquariums medical or life support devices etc What Other Limitations Apply The sole and exclusive remedies of the Initial Customer are those provided by this Warranty 1 This Warranty does not apply unless the Product and the equipment that was connected to it were connected to properly wired and grounded outlets including compliance with electrical and safety codes of the most current electrical code without the use of any adapters or other connectors 2 The Product must have been plugged directly into the power source and the equipment connected to the Product must be directly connected to the Product and not daisy chained together in serial fashion with any extension cords another Product or device similar to the Product surge suppressor or power tap Any such installation voids the Limited Warranty 3 The Product and equipment connected to it must have been used properly in a suitable and proper environment and in conformance with any license instruction manual or warnings provided with the Product and the equipment connected to it 4 The Product must have been used at all times within the limitations on the Product s VA capacity The Product was designed to eliminate disrupting and damaging effects of momentary less than 1ms voltage spikes or impulses from lightning or other power transients If it can be shown that a voltage
35. zardous voltage may exist between battery terminals and ground Test before touching CAUTION To reduce the risk of fire connect the UPS to a branch circuit with 40 amperes OL6000 50 amperes OL8000 60 amperes OL10000 maximum over current protection in accordance with the National Electric Code ANSI NFPA 70 CAUTION The AC outlet where the UPS is connected should be close to the unit and easily accessible CAUTION Please use only UL marked mains cable e g the mains cable of your equipment to connect the UPS to the AC outlet CAUTION Please use only UL marked power cables to connect any equipment to the UPS CAUTION When installing the equipment ensure that the sum of the leakage current of the UPS and the connected equipment does not exceed 3 5mA CAUTION The OL8000 0L10000 models are permanently connected equipment and only qualified maintenance personnel may carry out installations CAUTION Do not unplug the unit from AC Power during operation as this will invalidate the protective ground insulation CAUTION To avoid electric shock turn off and unplug the unit before installing the input output power cord with a ground wire Connect the ground wire prior to connecting the line wires CAUTION Do not use an improper size power cord as it may cause damage to your equipment and cause fire hazards CAUTION Wiring must be done by qualified personnel CAUTION DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQ

CyberPower OL8000RT3U uninterruptible power supply (UPS)

Contents

Download Pdf Manuals

Related Search

Related Contents