CyberPower CP750LCD uninterruptible power supply (UPS)
Contents
1. CyberPower Reliability Quality Value CP750LCDM User s Manual K01 0000121 00 IMPORTANT SAFETY WARNINGS SAVE THESE INSTRUCTIONS This manual contains important safety instructions Please read and follow all instructions carefully during installation and operation of the unit Read this manual thoroughly before attempting to unpack install or operate your UPS CAUTION To prevent the risk of fire or electric shock install in a temperature and humidity controlled indoor area free of conductive contaminants Please see specifications for acceptable temperature and humidity range CAUTION To reduce the risk of electric shock do not remove the cover There are no user serviceable parts inside CAUTION Hazardous live parts inside can be energized by the battery even when the AC input power is disconnected CAUTION The UPS must be connected to an AC power outlet with fuse or circuit breaker protection Do not plug into an outlet that is not grounded If you need to de energize this equipment turn off and unplug the unit CAUTION To avoid electric shock turn off the unit and unplug it from the AC power source before installing a computer component CAUTION Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer Data Processing Equipment ANSI NFPA 75 CAUTION To reduce the risk of fire connect only to a circuit provided with 20 amperes maximum branch circuit over current protection2. pe DISPLAY D ED re 1 ASe S Battery and Surge Protected Outlets The unit has four battery powered surge suppression outlets to ensure temporary uninterrupted operation of your equipment during a power failure DO NOT plug a laser printer paper shredder copier space heater vacuum Sump pump or other large electrical device into the Battery and Surge Protected Outlets The power demands of these devices will overload and possibly damage the unit Full Time Surge Protection Outlets The unit has four surge suppression outlets Power Switch Press the power button to turn the UPS on or off Power On Indicator green This LED is illuminated when the utility power is normal and the UPS outlets are providing power free of surges and spikes Electrical Wiring Fault Indicator red This LED indicator will illuminate to warn the user that a wiring problem exists such as bad ground missing ground or reversed wiring If this is illuminated disconnect all electrical equipment from the outlet and have an electrician verify the outlet is properly wired The unit will not provide surge protection without being plugged into a grounded and properly wired wall outlet Communication
3. and the item s of Connected Equipment Have information on all applicable insurance or other resources of recovery payment that are available to the Initial Customer and Request a Claim Number 3 You must provide a dated purchase receipt or other proof of the original purchase and provide a description of the damage to your connected equipment 4 Pack and ship the product to CyberPower and if requested the item s of Connected Equipment a repair cost estimate for the damage to the Connected Equipment and all claim forms that CyberPower provides to you Show the Claim Number on the shipping label or include it with the product You must prepay all shipping costs you are responsible for packaging and shipment and you must pay the cost of the repair estimate How Long Do I Have To Make A Claim All claims must be made within ten days of the occurrence What Will We Do To Correct Problems CyberPower will inspect and examine the Product If the Product is defective in material or workmanship CyberPower will repair or replace it at CyberPower s expense or if CyberPower is unable to or decides not to repair or replace the Product if defective within a reasonable time CyberPower will refund to you the full purchase price you paid for the Product purchase receipt showing price paid is required If it appears that our Product failed to protect any equipment plugged into it we will also send you forms for making your claim for the connect
4. increments AC Utility Mode UPS Status Display Capacity Display Digital Value Display Select SW Press i Input Output Voltage Voltage Ta of of M T pE E gt Pt et e pee E e E E e w e e e e e e e a e Pe ffx te P P P f P V light up go out not available Battery mode UPS Status Display Capacity Display Digital Value Display moe a Input Output Voltage Voltage sa of a of i Select SW Press 5th Return Press gt 3sec Sound Disable Press gt 3sec again Sound Enable V light up go out not available TROUBLESHOOTING Problem Possi Cause sowon Full time surge protection outlets idi T he UPS off l l i f stop providing power to Gradi bresker has mips disiioat urn the UPS o and unplug at least one piece O equipment Circuit breaker eoad equipment Wait 10 seconds reset the circuit breaker by button is projecting from the side f depressing the button and then turn the UPS on of the unit Battery not fully charged Recharge the battery by leaving the UPS plugged in The UPS does not perform expected runtime Contact CyberPower Systems about replacement batteries B ry i rn AEn Fe Wormi pul at tech cyberpowersystems com 2 em a Pera eels CEAC The on off switch is designed to prevent damage from rapidly turning it off and on Turn the UPS off Wait 10 seconds and then turn the UPS on The unit is not connected to an AC o
5. C Class B SYSTEM FUNCTION BLOCK DIAGRAM Input Output TPP lt Charger AC DC Battery gt Inverter Normal Mode lt TPP lt Battery Mode CYBERPOWER GREENPOWER UPS TECHNOLOGY Advanced Energy Saving Design The GreenPower UPS has a high efficiency charger which makes it the most energy efficient UPS in its class The advanced high frequency charging system significantly improves charging efficiency and conserves energy As a result of this advanced design the GreenPower UPS uses less energy compared to competitive models The GreenPower UPS is manufactured in accordance with the ENERGY SAVING TECHNOLOGY Restriction on Hazardous Substances ROHS directive making it one of the most environmentally friendly UPS on the market today Limited Warranty and Connected Equipment Guarantee Read the following terms and conditions carefully before using the CyberPower CP750LCDM the Product By using the Product you consent to be bound by and become a party to the terms and conditions of this Limited Warranty and Connected Equipment Guarantee together referred to as this Warranty If you do not agree to the terms and conditions of this Warranty you should return the Product for a full refund prior to using it Who is Providing this Warranty CyberPower Systems USA Inc CyberPower provides this Limited Warranty What Does This Warranty Co
6. Protection Ports Communication protection ports will protect any standard modem fax or telephone line RJ11 Circuit Breaker Located on the side of the UPS the circuit breaker serves to provide overload and fault protection USB Port to PC The USB port allows connection and communication between the USB port on the computer and the UPS unit The UPS communicates its status to the PowerPanel Personal Edition software The USB interface is also compatible with the Power Management applications provided by Windows 7 Vista Mac OS X and Linux Outlets Designed for AC Adapters The UPS unit has four widely spaced outlets so AC power adapters can be plugged into the UPS without overlapping adjacent outlets DEFINITIONS FOR ILLUMINATED LCD INDICATORS LOAD BATT CAP INPUT OUTPUT RUN_TIME INPUT voltage meter This meter measures the AC voltage that the UPS system is receiving from the a N 4 Ne Na utility wall outlet The UPS is designed to continuously supply connected equipment with stable lo ap V gt 110 120 output voltage In the event of a complete power loss severe brownout or over voltage the 1K OX A UPS relies on its internal battery to supply consistent 110 120 output voltage The INPUT voltage The LCD display indicates a variety of UPS operational conditions All descriptions apply when the UPS is plugged into an AC outlet and turned ESTIMATE RUN TIME This displays the run time estimate of the UPS wi
7. ansients spikes or surges on properly installed grounded and code compliant 120 volt power lines in the United States and Canada transients surges or spikes on standard telephone land lines PBX telephone equipment lines or Base 10T Ethernet lines when properly installed and connected This exclusion applies for example to fluctuations in data transmission or reception by CATV or RF transmission or fluctuations or by transients in such transmission Damage from any circumstance described as excluded above with respect to the Product 4 Damages from fire flood wind rain rising water leakage or breakage of plumbing abuse misuse or alteration of either the product or the Connected Equipment 5 CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment Guarantee CyberPower excludes any liability for direct indirect special incidental or consequential damages whether for damage to or loss of property EXCEPT FOR AND ONLY FOR the specific limited agreement of CyberPower to provide certain warranty benefits regarding Connected Equipment under this Warranty loss of profits business interruption or loss of information or data NOTE Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you 6 The Product is not for use in high risk activities or with aquariums The Product is not designed or inte
8. ed equipment We will repair or replace the equipment that was damaged because of the failure of our Product or pay you the fair market value NOT REPLACEMENT COST of the equipment at of the time of the damage We will use Orion Blue Book or another a third party valuation guide or eBay craigslist or other source to establish that amount Our maximum liability is limited to 150 000 for the CP750LCDM Who Pays For Shipping We pay when we send items to you you pay when you send items to us What isn t covered by the warranty 1 This Warranty does not cover any software that was damaged or needs to be replaced due to the failure of the Product or any data that is lost as a result of the failure or the restoration of data or records or the reinstallation of software 2 This Warranty does not cover or apply to misuse modification operation or storage outside environmental limits of the Product or the equipment connected to it nor for damage while in transit or in storage nor if there has been improper operation or maintenance or use with items not designed or intended for use with the Product such as laser printers appliances aquariums medical or life support devices etc What are the Limitations The sole and exclusive remedies of the Initial Customer are those provided by this Warranty 1 This Warranty does not apply unless the Product and the equipment that was connected to it were connected to properly wired and grounded outle
9. in accordance with the National Electric Code ANSI NFPA 70 CAUTION Risk of explosion if battery is replaced by an incorrect type Batteries shall be installed by service personnel and the replacement of batteries with a suitable recommended type Dispose of used batteries according to the instructions CAUTION Do not dispose of batteries in a fire The batteries may explode CAUTION Do not open or mutilate batteries Released electrolyte is harmful to the skin and eyes It may be toxic DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT CyberPower Systems does not sell products for life support or medical applications DO NOT use in any circumstance that would affect operation and safety of life support equipment any medical applications or patient care DO NOT USE WITH OR NEAR AQUARIUMS To reduce the risk of fire or electric shock do not use with or near an aquarium Condensation from the aquarium can cause the unit to short out INSTALLING YOUR UPS SYSTEM UNPACKING Inspect the UPS upon receipt The box should contain the following a UPS unit b User s manual c PowerPanel Personal Edition software CD d USB device cable e Telephone cable f Warranty registration card HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT 1 Ensure that the equipment plugged into the outlet does not exceed the UPS unit s rated capacity 750VA 420W for CP750LCDM If the rated capacities of the unit are exceeded an overload conditio
10. n may occur and cause the UPS unit to shut down or the circuit breaker to trip 2 There are many factors that can affect the amount of power that your computer system will require For optimal system performance keep the load below 80 of the unit s rated capacity HARDWARE INSTALLATION GUIDE 1 Your new UPS may be used immediately upon receipt However after receiving a new UPS to ensure the battery s maximum charge capacity it is recommended that you charge the battery for at least 8 hours Your UPS is equipped with an auto charge feature When the UPS is plugged into an AC outlet the battery will automatically charge when it s turned on or turned off 2 With the UPS unit turned off and unplugged connect your computer monitor and any other peripherals requiring battery backup from the SURGE BATTERY outlets Plug the other peripheral equipment eg printer scanner speakers etc into the full time surge protection outlets DO NOT plug a laser printer paper shredder copier space heater vacuum sump pump or other large electrical device into the Battery and Surge Protected Outlets The power demands of these devices will overload and possibly damage the unit 3 To protect a fax phone or modem connect a telephone cable from the wall jack outlet to the IN jack of the UPS Connect a telephone cable from one of the UPS OUT jacks to the modem port on the computer aes The other UPS OUT jack can be used to protect a teleph
11. nded for use in hazardous environments requiring fail safe performance or for use in any circumstance in which the failure of the Product could lead directly to death personal injury or severe physical or property damage or that would affect operation or safety of any medical or life support device collectively High Risk Activities CyberPower expressly disclaims any express or implied warranty of fitness for High Risk Activities or with aquariums CyberPower does not authorize use of any Product in any High Risk Activities or with Aquariums ANY SUCH USE IS IMPROPER AND IS A MISUSE OF THE PRODUCT The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded CyberPower is the warrantor under this Limited Warranty Where Can I Get More Information For further information please feel free to contact CyberPower at Cyber Power Systems USA Inc 4241 12 Ave E STE 400 Shakopee MN 55379 call us at 877 297 6937 or send us an e mail message at claims cyberpowersystems com All rights reserved Reproduction without permission is prohibited
12. one or fax machine 4 Plug the UPS into a 2 pole 3 wire grounded receptacle wall outlet Make sure the wall branch outlet is Phone OUT gt oO PC protected by a fuse or circuit breaker and does not service equipment with large electrical demands e g air conditioner refrigerator copier etc The warranty prohibits the use of extension cords outlet strips and surge strips 5 Press the power switch to turn the unit on The Power On indicator light will illuminate green and the unit will beep twice 6 If an overload is detected an audible alarm will sound and the unit will emit one long beep To correct this turn the UPS off and unplug at least one piece of equipment from the battery power supplied outlets Make sure the circuit breaker is depressed and then turn the UPS on 7 To maintain optimal battery charge leave the UPS plugged into an AC outlet at all times 8 To store the UPS for an extended period cover it and store with the battery fully charged While in storage recharge the battery every three months to ensure optimal battery life 9 Insure the wall outlet and UPS are located near the equipment being attached for proper accessibility BASIC OPERATION DESCRIPTION 6 0 5 A f Di mn 7 SS I f O
13. s the listed capacity of the UPS Turn the UPS off unplug at least one Constant tone l l piece of equipment from battery outlets wait 10 seconds reset the circuit breaker and turn the unit on Electrical Wiring Fault This indicates a wiring problem with the On Off AC outlet such as bad ground missing ground or reversed wiring Disconnect all electrical equipment from the outlet and have an electrician check the outlet to insure proper wiring Utility Failure The frequency is beyond 47 63Hz The UPS will not turn on in AC Utility Power Mode TECHNICAL SPECIFICATIONS 750VA 420W Capacity Input Frequency 47 Hz to 63 Hz On Battery Output Voltage 120Vac 5 50Hz 60Hz On Battery Output Frequenc j i UPS boots in battery mode 60Hz Transfer Time 4ms Typical Max Load for UPS Outlets 4 Outlets 750VA 420W Max Load for Full Time Surge Protection 12 Amps outlets 8 Outlets On Battery Output Wave Form Simulated Sine Wave Operating Temperature 32 F to 104 F 0 C to 40 C Operating Relative Humidity 0 to 90 non condensing 10 4 x 6 9 x 3 1 Size LxWxH l 263 x 176 x 80 mm Net Weight 6 7 lbs 3 04kg Typical Battery Recharge Time 8 hours typical from total discharge Typical Battery Life 3 to 6 years depending on number of discharge recharge cycles Recommended Battery Sealed Maintenance Free Lead Acid Battery Safety Approvals UL1778 UPS cUL CSA C22 2 No 107 3 05 FCC Do
14. th the current battery on or when the UPS is on battery meter can be used as a diagnostic tool to identify poor quality input power OUTPUT voltage meter This meter measures in real time the AC voltage that the UPS system is providing to the computer during normal AC Utility Power mode and battery backup mode capacity and load NORMAL icon This icon appears when the UPS is working under normal conditions BATTERY icon During a severe brownout or blackout this icon appears and an alarm sounds two short beeps followed by a pause to indicate the UPS is operating from its internal battery During a prolonged brownout or blackout the alarm will sound continuously The BATT CAPACITY meter will show one 20 capacity segment remaining to indicate the UPS s battery is nearly out of power You should save files and turn off your equipment immediately OVER LOAD icon This icon appears and an alarm sounds to indicate the battery supplied outlets are overloaded To clear the overload unplug some of your equipment from the battery supplied outlets until the icon turns off and the alarm stops BATT CAPACITY meter This meter displays the approximate charge level of the UPS s internal battery in 20 increments During a blackout or severe brownout the UPS switches to battery power the BATTERY icon appears and the battery charge level decreases LOAD CAPACITY meter This meter displays the approximate output load level of the UPS battery outlets in 20
15. ts including compliance with electrical and safety codes of the most current electrical code without the use of any adapters or other connectors 2 The Product must have been plugged directly into the power source and the equipment connected to the Product must be directly connected to the Product and not daisy chained together in serial fashion with any extension cords another Product or device similar to the Product surge suppressor or power tap Any such installation voids the Limited Warranty 3 The Product and equipment connected to it must have been used properly in a suitable and proper environment and in conformance with any license instruction manual or warnings provided with the Product and the equipment connected to it 4 The Product must have been used at all times within the limitations on the Product s VA capacity The Product was designed to eliminate disrupting and damaging effects of momentary less than 1ms voltage spikes or impulses from lightning or other power transients If it can be shown that a voltage spike lasting longer than 1ms has occurred the occurrence will be deemed outside the rated capabilities of the Product and the Limited Warranty is void CyberPower Does Not Cover or Undertake Any Liability in Any Event for Any of the Following Loss of or damage to data records or software or the restoration of data or records or the reinstallation of software 2 Damage from causes other than AC Power Line Tr
16. utlet The unit must be connected to a 110 120V 50 60Hz outlet The UPS will not turn on Contact CyberPower Systems about replacement batteries at tech cy berpowersystems com The battery is worn out Contact CyberPower Systems at tech cyberpowersystems com Mechanical problem Turn the UPS off Make sure the frequency range is within 47 63Hz Or you can turn the UPS on in battery mode The frequency is beyond 47 63Hz Connect the USB cable to the UPS unit and an open USB The USB cable is not connected noir on te bacco ihe compuler PowerPanel Personal Edition is f 3 The USB cable is connected to the inactive all icons are gray wrong port Check the back of the computer for an additional USB port Move the cable to this port Shutdown your computer and turn the UPS off Wait 10 seconds and turn the UPS back on This should reset the unit The unit is not providing battery power Additional troubleshooting information can be found at Support at www CPSww com DEFINITIONS FOR ILLUMINATED LED INDICATORS 2 A Power ON CONDITION Wiring Fault Beep twice Utility Failure The UPS is providing power to battery power supplied every 30 seconds outlets from its battery Rapid Beeping Utility Failure The UPS is providing battery power Rapid beeping every 1 2 second indicates the unit will run out of power shortly Battery Overload Occurs when connected equipment exceed
17. ver This warranty covers defects in materials and workmanship in the Product under normal use and conditions It also covers equipment that was connected to the Product and damaged because of the failure of the Product What is the Period of Coverage This warranty covers the Product for three years and connected equipment for as long as you own the Product Who Is Covered This warranty only covers the original purchaser Coverage ends if you sell or otherwise transfer the Product How Do You Get Service 1 Call us at 877 297 6937 or write to us at Cyber Power Systems USA Inc 4241 12 Ave E STE 400 Shakopee MN 55379 or send us an e mail message at claims cyberpowersystems com for instructions 2 When you contact CyberPower identify the Product the Purchase Date and the item s of Connected Equipment Have information on all applicable insurance or other resources of recovery payment that are available to the Initial Customer and Request a Claim Number 3 You must provide a dated Proof of Purchase receipt or other proof of the original purchase and provide a description of the defect How Do You Open A Connected Equipment Claim 1 Call us at 877 297 6937 or write to us at Cyber Power Systems USA Inc 4241 12th Ave E STE 400 Shakopee MN 55379 or send us an e mail message at claims cpsww com for instructions within 10 days of the occurrence 2 When you contact CyberPower identify the Product the Purchase Date
Download Pdf Manuals
Related Search