König PCI WLAN
Contents
1. K COMICS COMPUTER CMP WNPCI10 Wireless LAN PCI 54 Mbps Manual ENGLISH Package Contents The following contents should be found in your box gt One 54 Wireless Adapter gt One Resource CD including e Wireless Client Utility WCU and Drivers e User Guide e Network cable Note If any of the listed contents are damaged or missing please contact the retailer from whom you purchased the Wireless Adapter for assistance Chapter 1 Introduction 1 1 Overview of the product The Wireless Adapter gives you the flexibility to install your PC in the most convenient location available without the cost of running network cables The adapter s auto sensing capability allows high packet transfer rate of up to 54Mbps for maximum throughput or dynamic range shifting to lower speeds due to distance or operating limitations in an environment with a lot of electromagnetic interference It can also interoperate with all 11Mbps wireless 802 11b products Your wireless communications are protected by up to 152 bit WEP and WPA encryption for high security Transmission distance is 2 3 times further than of traditional 11g b solutions up to 855 36m Transmission range is extended to 4 9 times 1 2 Features gt Complies with IEEE802 11g IEEE802 11b standards gt Transmission distance 2 3 times further than traditional solutions gt Supports WPA data security IEEE802 1x authentication TKIP AES encryption 64 128 152 bit WEP2. EUGRRERE ood Figure 3 1 Current Status The following table describes the items found on the Current Status screen gt Profile Name The name of current selected configuration profile Set up the configuration name on the General tab of Profile Management gt Link Status Shows whether the station is associated to the wireless network gt Wireless Mode Displays the wireless mode Configure the wireless mode on the Advanced tab of Profile Management gt Network Type The type of network and the station currently connected The options include e Infrastructure access point e Ad Hoc Configure the network type on the Advanced tab of Profile Management gt IP Address Displays the computer s IP address gt Current Channel Shows the currently connected channel gt Data Encryption Displays the encryption type the driver is using Configure the encryption type on the Security tab of Profile Management gt Server Based Authentication Shows whether server based authentication is used gt Signal Strength Shows the strength of the signal Note In the WCU utility access the General tab Security tab and Advanced tab by clicking New or Modify on the Profile Management tab Click Advanced to see advanced information about the program and its operations For more information Please refer to the help file of the utility 3 2 Profile Management Click the Profile Management tab of the WCU Utility and th
3. 1 Wireless Client Utility Install Shield Wizard 3 To continue click Next on the screen figure 2 2 Click Cancel to end the Installation Wireless Client Installation Program Wireless Client Installation Program This program installs the driver and client utilities for your Wireless PCI card Figure 2 2 Wireless Client Utility Installation Program The Setup Wizard will ask you to choose a Setup type in figure 2 3 It is recommended that you select Install Client Utilities and Driver Select Install Driver Only to install driver only select Make Driver Installation Diskette s to make the diskette s as the installation driver Select Install Client Utilities and Driver and click Next to continue the Installation Click Back to return to the previous page or click Cancel to end the Installation Wireless Client Installation Program Setup Type Select the setup type that best suits your needs Click the type of setup you prefer Install Client Utilities and Driver p Description Install Driver Only Choose this option to install the Make Driver Installation Diskette s driver and client utilities This is the recommended option InstallShield pee Figure 2 3 Select the setup type Figure 2 4 should appear Click Yes to continue the Installation or click No to end the Installation ovestion 2 6 The option you have selected requires the system to be rebooted at the end
4. encryption Supports 108 54 48 36 24 18 12 9 6 11 5 5 3 2 1 Mbps wireless LAN data transfer rates Provides 32 bit PCI interface 54M Wireless PCI Adapter or 32 bit CardBus interface 54M Wireless CardBus Adapter Supports Ad Hoc and Infrastructure modes Supports roaming between access points when configured in Infrastructure mode Eases to configure and provides monitoring information Supports Windows 98 Me 2000 XP v v VV VV 1 3 LED Status 1 3 1 54M Wireless PCI Adapter LED Indications LED Indications Status Working Status Status Green Intermittently The adapter is in an electricity saving status or the adapter is already connected but is not transmitting or receiving data Status Green Light up The adapter is on wake up status Status Green Flashing The adapter is transmitting and receiving data Chapter 2 Installation Guide 2 1 Hardware Installation 2 1 1 54M Wireless PCI Adapter Hardware Installation To install the adapter follow these steps listed below 1 Turn off your desktop PC and disconnect the power 2 Open your PC case and locate an available PCI slot on the motherboard Remove the metal slot cover on the back of the PC Check with your computer manufacturer for instructions if needed 3 Slide the PCI Adapter into the PCI slot Make sure that all of its pins are touching the slot s contacts Once the adapter is firmly in place secure its fastening ta
5. n Starting Ad Hoc Networ 24GH254 Mbps 24GHz211 Mbps 24GHz211 Mbp 24GH254 Mbp FF extended Range xP see al 402 7 uthent Mot E Qos Auto Ope aj ared Preferred APs Cancel Figure 3 6 Advanced tab of Profile Management 3 2 2 Remove a profile 1 2 3 Go to the Profile Management tab Select the profile name to remove in the Profiles List Click Remove 3 2 3 Switch another Profile 1 2 Go to the Profile Management tab Click on the profile name in the Profiles List 10 3 Click Activate 3 2 4 Import a Profile 1 From the Profile Management tab click Import The Import Profile will then appear 2 Browse to the directory where the profile is located 3 Highlight the profile name 4 Click Open the imported profile will then appear in the Profiles List 3 2 5 Export a Profile 1 From the Profile Management tab highlight the profile to export 2 Click Export the Export Profile window will then appear 3 Browse the directory to export the profile to 4 Click Save The profile should then be exported to the specified location 3 2 6 Scan Available Networks 1 Click Scan on the Profile Management the Available Infrastructure and Ad Hoc Networks window will appear 2 Click Refresh to refresh the list at any time 3 Highlight a network name and click Activate to connect an available network If no configuration profile exists for that network the Profile Ma
6. 08M Wireless Adapter has not passed Windows Logo testing to verify its compatibility with Windows xP Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing STOP Installation Figure 2 8a Windows XP Warning Box 10 After the files have been successfully copied the screen in figure 2 9 will appear Click Finish to reboot the system Wireless Client Installation Program InstallShield Wizard Complete The Installation Program has successfully performed the selected operations but the system needs to be rebooted before all of the changes will take effect Select Yes to reboot the system C No will restart my computer later Remove any disks from their drives and then click Finish to complete setup lt Back Cancel Figure 2 9 Finish Chapter 3 Configuration The Wireless Adapter can be configured by Wireless Client Utility WCU This chapter describes how to configure your Wireless Adapter for wireless connectivity on your Wireless Local Area Network WLAN and use the data security encryption features After Installing the Adapter the Adapter s tray icon alll will appear in your system tray It appears at the bottom of th
7. ailable network is found Auto Profile Selection Management 2 x r Available Profiles Add we r Auto Selected Profiles Figure 3 7 Auto Profile Selection Management Dialog 11 DECLARATION OF CONFIRMITY We declare under our responsibility that the product Brand name KONIG Model CMP WNPCI10 Description Wireless PCI adapter Is in conformity with the following standards EN 300 328 V 1 4 1 2003 EN 301 489 1 V 1 4 1 2002 EN 301 489 17 V 1 2 1 2002 EN 60950 1 2001 Following the provisions of the 1999 5 EC R amp TTE Directive Conform this regulation it s allowed to use this product in all European Community amp EFTA countries Nedis BV is not responsible for the use of this product outside the European Community amp EFTA countries WARNING Disconnect the product from mains and other equipment if a problem should occur Do not expose the product to water of moisture WARRANTY No guarantee or liability can be accepted for any changes and modifications of the product or damage caused due to incorrect use of this product GENERAL Designs and specifications are subject to change without a notice 12 sls www konigcomputer com
8. b to your PC s chassis with a mounting screw Then close your PC case 4 Reconnect your PC s power and turn on your desktop PC 2 2 Software Installation 2 2 1 Overview The Adapter s Setup Wizard will guide you through the Installation procedure for Windows 2000 XP The Setup Wizard will install the Wireless Client Utility WCU and drivers When you install the hardware before installing the software the system will prompt Found New Hardware Wizard window click Cancel and run the Setup Wizard program on the CD ROM The Setup steps for Windows 2000 and Windows XP are very similar The following setup steps are for Windows 2000 2 2 2 Software Installation for Windows 2000 1 Insert the Resource CD into your CD ROM drive click Start and choose Run In the field that appears enter F WNPCI10 Win2000_XP Setup exe if F is the letter of your CD ROM drive figure 2 1 should then appear 2 You can click Cancel to end the installation on the Preparing Setup screen figure 2 1 Otherwise the Setup Wizard will display a screen similar to that shown in figure 2 2 after a moment 54 108M Wireless Adapter Applications InstallShield Wizard loj xj Preparing Setup Please wait while the InstallShield Wizard prepares the setup 54 108M Wireless Adapter Applications Setup is preparing the InstallShield Wizard which will guide you through the rest of the setup process Please wait Cancel Figure 2
9. e Pett o Client Name NEO2 P r Network Names SSID1 Wireless SSID2 SSID3 Figure 3 3 General Tab of Profile Management Edit the Security tab Edit the fields in the Security tab of Profile Management to configure the profile To define the security mode select the radio button of the desired security mode gt gt gt gt WPA Wi Fi Protected Access WPA Passphrase Wi Fi Protected Access Passphrase 802 1x Enables 802 1x security Shared Key Static WEP Enables the use of shared keys that are defined on both the access point and the station To define shared encryption keys choose the Shared Key radio button and click Configure to fill in the Define Shared Keys window None No security not recommended Note If the access point that the wireless adapter is associating to has WEP set to Optional and the client has WEP enabled make sure that Allow Association to Mixed Cells is checked on the Security Tab to allow association To complete WEP encryption configuration you must select the 802 11 Authentication Mode as appropriate on the Advanced tab of this Profile Management dialog Profile Management 21x General Security Advanced Set Security Options C WPAAWPA2 C WPAAVPA2 Passphrase C 8021x red Key Static WEP 802 1x EAP Type LEAP WPAAWPA2 EAP Type LEAP Z Cancel Figure 3 4 Security tab of Profile Management Define Pre Shared Ke
10. e 2 7 Click OK to continue the Installation Wireless Client Installation Program 3 x The installation program installs the driver automatically when the client adapter is inserted Insert the adapter now if it is not yet inserted cancel the Found New Hardware Wizard if it appears and proceed with the installation Click OK to continue Figure 2 7 Information prompt While files are copying you will see a warning box shown in figure 2 8 Please select YES to continue installation Our drivers have been tested thoroughly and are able to work with the operating system Digital Signature Not Found xi The Microsoft digital signature affirms that software has been tested with Windows and that the software has not been altered since it was tested The software you are about to install does not contain a Microsoft digital signature Therefore there is no guarantee that this software works correctly with Windows 54 108M Wireless Adapter If you want to search for Microsoft digitally signed software visit the Windows Update Web site at http windowsupdate microsoft com to see if one is available Do you want to continue the installation i No More Info Figure 2 8 Widows 2000 Warning Box Note In Windows XP the warning box is similar to that shown figure 2 8a Please select Continue Anyway to continue installation Hardware Installation A The software you are installing for this hardware 54 1
11. e Profile Management screen will appear figure 3 2 The Profile Management screen provides tools to Add a profile Edit a profile Remove a profile Switch to another Profile Import a Profile Export a Profile Scan Available Networks Order profiles Wireless Client Utility Current Profile LINK i 21x Action Options Help VVVVVVV WV Current Status Profile Management Diagnostics Hew Modify Details Network Type Infrastructure Teeth Security Mode Disabled Network Name 1 SSID1 lt empty gt Export Network Name 2 SSIDZ lt empty gt Network Name 3 SSID3 lt empty gt T Auto Select Profiles Order Profiles Scan Figure 3 2 Profile Management tab 3 2 1 Add or Modify a Configuration Profile To add a new configuration profile click New on the Profile Management tab To modify a configuration profile select the configuration from the Profile list and click Modify The Profile Management dialog box will display a screen similar to that shown in Figure 3 3 1 Edit the General tab gt Profile Name Identifies the configuration profile This name must be unique Profile names are not case sensitive gt Client Name Identifies the client machine gt Network Names SSIDs The IEEE 802 11 wireless network name This field has a maximum limit of 32 characters 2 Profile Management 21x General Security Advanced Profile Settings Profile Nam
12. e screen and shows the signal strength using color and the received signal strength indication RSSI il If the icon is gray there is no connection If the icon is red there is poor signal strength and the RSSI is less than 5dB If the icon is yellow there is poor signal strength and the RSSI is between 5dB and 10dB If the icon is green there is good signal strength and the RSSI is between 10dB and 20cB all Double click the icon and the WCU utility will run You can also run the utility by clicking the Start gt Program gt Wireless gt Wireless Client Utility The WCU utility provides a complete and easy to use set of tools to gt Display current status information gt Edit and add configuration profiles gt Display current diagnostics information If the icon is green there is excellent signal strength and the RSSI is more than 20dB The section below introduces these above capabilities 3 1 Current Status The Current Status tab contains general information about the program and its operations The Current Status tab does not require any configurations Wireless Client Utility Current Profile LINK 2 x Action Options Help Current Status Profile Management Diagnostics Profile Name LINK Link Status Associated Wireless Mode 2 4 GHz 54 Mbps IP Address 0 0 0 0 Network Type Infrastructure Current Channel 6 Server Based Authentication None Data Encryption None Signal Strength
13. nagement window will open the General tab Fill in the Profile name and click OK to create the configuration profile for that network 3 2 7 Auto Profile Selection Management The auto selection feature allows the wireless adapter to automatically select a profile from the list of profiles and use it to connect to the network To add a new profile into the Auto Selected Profiles list please follow these steps 1 On the Profile Management tab click Order Profiles 2 The Auto Profiles Selection management window will appear with a list of all created profiles in the Available Profiles box 3 Highlight the profiles to add to auto profile selection and click Add The profile will appear in the Auto Selected Profiles box 4 Highlight a profile in the Auto Selected Profiles box 5 Click Move Up or Move Down as appropriate Note The first profile in the Auto Selected Profiles box has highest priority and the last profile has lowest priority 6 Click OK 7 Check the Auto Select Profiles checkbox on the Profile Management tab Note When auto profile selection is enabled by checking Auto Select Profiles on the Profile Management tab the client adapter will scan for an available network The profile with the highest priority and the same SSID as one of the found networks will be used to connect to the network If the connection fails the client adapter will try the next highest priority profile that matches the SSID until an av
14. ng an Ad Hoc Network Specifies 2 4 GHz 54 11Mbps to start an Ad Hoc network if no matching network name is found after scanning all available modes This mode also allows the selection of the channel the wireless adapter uses The channels available depend on the regulatory domain If the adapter finds no other ad hoc adapters the channel that the adapter starts the ad hoc network with will be selected automatically The wireless adapter must match the wireless mode and channel of the clients it associates 802 11 Authentication Mode Select which mode the wireless adapter uses to authenticate to an access point e Automatic causes the adapter to attempt authentication using shared but switches it to open authentication if shared fails e Open System enables an adapter to attempt authentication regardless of its WEP settings It will only associate with the access point if the WEP keys on both the adapter and the access point match e Shared key only allows the adapter to associate with access points that have the same WEP key For infrastructure access point networks click Preferred APs to specify up to four access points to the client adapter that attempts to be associated to the access points Profile Management zjx General Security Advanced raene Rowe Lavel Power Save Mode Ww X so211b a i00nw x Network Type Infrastructure x 802 a 140 m A E B02 11b Preanbie Short Long Long Ony Wireless Mode Wireless Mode
15. of the operation Do you want to continue Figure 2 4 Question Click Browse to change the destination location for the software in figure 2 5 Click Next to continue the Installation Click Back to return to the previous page or click Cancel to end the Installation Wireless Client Installation Program E xj Choose Destination Location Select the folder where the installation program will install the files The installation program will install the client utilities in the following location Destination Folder D Program Files Wwireless Browse InstallShield lt Back Cancel Figure 2 5 Choose Destination Location The Setup Wizard will ask you to create a new folder name or select one from the Existing Folders list shown in figure 2 6 It is recommended that you keep the default value Click Next to continue the Installation Click Back to return to the previous page or click Cancel to end the Installation Wireless Client Installation Program Select Program Folder Select a program folder The installation program will add program icons to the Program Folder listed below You may enter a new folder name or select one from the Existing Folders list Program Folder ESS Existing Folders Realtek Sound Manager InstallShield eae Figure 2 6 Select a Program Folder The Setup Wizard will notify you of how to proceed with the installation shown in figur
16. ys 2x p Key Entry ASCII Text all keyboard characters Encryption Keys WEP Key Size 64 128 152 WEP Key 1 C a WEP Key 2 C ce WEP Key 3 C WEP Key 4 C G c eC s C c c Cc Cancel Figure 3 5 Define Shared Keys v Vv Edit the Advanced tab Transmit Power Level Selects the transmit power level for 802 11b g in mW Actual transmit power may be limited by regulatory domain or hardware limitations Power Save Mode e Maximum Selects maximum mode to let the access point buffer incoming messages for the wireless adapter The adapter will detect the access point if any messages are waiting periodically Normal In Normal mode the adapter will be switched to maximum mode automatically when no large packets are retrieved e Off turns power saving off thus powering up the wireless adapter continuously for a short message response time 802 11b Preamble Specifies the preamble setting in 802 11b The default setting is Short amp Long access point mode which allows both short and long headers in the 802 11b frames The adapter can only use short radio headers if the access point supports and uses them Set to Long Only to override allowing short frames Wireless Mode Specifies 2 4 GHz 54 Mbps 2 4 GHz 11 Mbps operation in an access point network The wireless adapter must match the wireless mode of the access point with which it associates Wireless Mode when Starti
Download Pdf Manuals
Related Search