Panasonic TY-TP42P30K
Contents
1. Panasonic Illustrations are conceptual views and may differ in shape from the actual equipment The specifications of the product are subject to change without notice e Windows is a registered trademark of Microsoft Corporation in the USA and other countries The official name of Windows is Microsoft Windows Operating System e The names of other companies and products appearing in this publication are the trademarks registered trademarks or products names of their respective owners Touch Panel Assembly e Place the touch panel making its front surface face down on a clean cloth or blanket to prevent the front surface of the touch panel from getting scratched or dirty during work Mounting in horizontal posture Attach the mounting brackets A for top and bottom sides to the touch panel with the mounting screws A 2 each See the figure below for the screw holes of attachment positions The procedure for vertical posture is at same Mounting screw A Mounting bracket A for top side Mounting bracket A for bottom xT Mounting screw A side QE BSN Attachment positions n 8 holes without screws in them pA eA Mounting in vertical posture Check in the figure below the positions where the brackets are attached and remove the screws 8 in total from top and bottom sides Attach the mounting brackets A for top and bottom sides with the mounting screws A 2 each to the screw holes from which2. the screws were removed e For screw holes of other models than 42V see Drawing of Screw Holes page 14 Keep the screws which were removed Top side 42V Mounting Touch Panel e Two or more people are always required for mounting e Never mount the main device in the way that is overlapped from above the touch panel while the touch panel is laid down Doing so may damage the touch panel 14 Fit the assembled touch panel from the front side of the main device e There should not be a space between the touch panel and the front surface of main device The procedure for vertical posture is the same Mount in the way that the USB port becomes lower left when seen from the front 2 Prepare the mounting brackets B B A Mounting bracket B Temporarily fix the mounting screws B 2 or 3 turns As shown in the figure below attach the mounting brackets B to the mounting brackets A for top side on the left and right of the top side Temporarily fix the screws Attach on the left and right of the bottom side in the same way Securely insert the projection of the mounting bracket B to the cutout Attaching to the top side Mounting bracket B Attaching to the bottom side Mounting bracket B A Securely insert the projection of the mounting bracket B to the cutout 4 Referring to the alignment mark shown in t
3. Panasonic Operating Instructions Touch Panel modelo Y TP42P30K TY TPS0P30K TY TP60P30K TY TP65P30K Before connecting operating or adjusting this product please read these instructions completely Please keep this manual for future reference Contents m Precautions with regard to setting UP eee 2 m Operating COnditionS cc eeeeeeeeeeeeeeeeeeseeeeenees 8 M Maintenance riiit neire iiaeiai isesi o 3 m Touch Operation ceeceececesseceeeeeeeeeeeeeeeeeeeeeeeeaeees 9 EC OMPONEN S ese ereraa e Eai 4 m Before Calling for ServiCe ecceeeeeeeeeeteeeeees 10 m Touch Panel Assembly ccccceeeeeeeseeeteeeeeeees 5 E Specifications 2 02 eee eee seinn ie aiai Ee 13 m Mounting Touch Panel esseesseeeeeeseeeerreesrereerreees 6 m External Dimensions eseeeeseeeeeeeeeee eerren 14 m Connection with Computer seesseeseeeseereesreeereeeeee 8 m Drawing of Screw Holes c cceceeceeeeereeeeeteeeenees 14 Precautions with regard to setting up WARNING Only a qualified technician should perform installation e Incorrect installation may cause an accidental fall of the equipment resulting in personal injury Do not disassemble or modify the equipment e Doing so may cause a fire or electric shock Stop using the equipment if anything abnormal occurs e Using the equipment even when it is generating smoke or an odor or in ot
4. Table of external dimensions Unit mm B o2 722 s02 9332 The dimensions may vary depending on the device to be mounted to or the status of tightening Drawing of Screw Holes Mounting in vertical posture e Refer to page 5 for 42V For 50V Top Bottom For 60V Top Bottom For 65V Top Bottom 14 Customer s Record The model number and serial number of this product can be found on its bottom side You should note this serial number in the space provided below and retain this book plus your purchase receipt as a permanent record of your purchase to aid in identification in the event of theft or loss and for Warranty Service purposes Warranty conditions are managed by distributors to meet the standards set by each country For details contact your dealer where you made your purchase Model Number Serial Number Pursuant to at the directive 2004 108 EC article 9 2 Panasonic Corporation Panasonic Testing Centre Panasonic Service Europe a division of ey Sita Nip panasgnienet Panasonic Marketing Europe GmbH p Winsbergring 15 22525 Hamburg F R Germany Printed in Japan M0212 0
5. able i window before the second touch is made If the distance is not enough the double tap may not be correctly recognized f Functions as a drag and drop of mouse by touching moving a Drag and drop Applicable Applicable i a oe finger while it is kept contacted and then releasing it Not When a frequently executed operation has been set flipping fo Flick Applicable a finger toward the location of the function to be used can applicable execute the operation Not Functions as a right click by touching and holding on the area 0 Press and hold PET Applicable of the screen where you want to make a right click and then applicable pe releasing it Not On a page with the scroll bar touching and moving toward fe Pan f Applicable the direction you want can scroll the page along with the applicable movement On the screen which can be zoomed in and out touching the Not screen with two fingers and separating the touching points 0 Zoom Applicable from each other in the manner of stretching enables zooming applicable cease in Moving the touching points closer in the manner of pinching enables zooming out Not Functions as a right click of mouse by touching and holding fe Press and tap licabl Applicable a finger on the screen and quickly making a single tap with applicable He another finger e When using Windows 7 confirm that Enable multi touch gestures and inking is checked in Pen and Touch o
6. ble supplied with the equipment This equipment is a touch panel using infrared rays Incident light containing infrared rays may hinder operation of the touch panel Sunlight It is not a problem as long as the infrared transmissive part of the touch panel is not directly exposed to sunlight Fluorescent light It can be a problem because some types of fluorescent light particularly inverter type produce infrared rays White candescent light It can be a problem because it contains much infrared rays Keep as long a distance as possible between the equipment and the light source or prevent the infrared transmissive part from being directly exposed to the light Device using infrared rays Malfunction may occur if a remote control or other device using infrared rays is used for the touch panel Start up the OS Check that Use your finger as an input device is checked in Touch of Pen and Touch of Control Panel For more information see the help information of Windows Check that the USB cable is connected If using a USB hub check that the power is supplied from the USB hub Do not use the equipment near from a device causing much electrical noise The noise affects the power source and interface and may cause malfunction Check point Action to take Response is Are strong light sources or lost during devices that use infrared operation rays located nearby Are strong light sources or devices t
7. ecause some cables may not ensure the proper functioning of the equipment use the USB extension cable supplied with the equipment Operating Conditions OS of computer IBM PC AT compatible machine with USB ports supporting the OS below Windows XP SP2 or later 32 bit or 64 bit Windows Vista 32 bit or 64 bit Windows 7 SP1 or later 32 bit or 64 bit e The USB ports should function correctly e If a previous version of driver has been installed disconnect the USB cable of the touch panel from the computer uninstall the previous version and then install the new one e For installation and uninstallation of the touch panel driver see the installation manual of the touch panel driver software included in the supplied CD ROM e When using Windows 7 installation of the touch panel driver is not necessary When using Windows XP or Vista follow the descriptions of the installation manual of the driver software included in the supplied CD ROM for connection of the USB extension cable and setup of the touch panel driver software Touch Operation Use the supplied touch pen The touch operations are different depending on the OS used Dual touch is not possible on Windows XP and Vista XP 7 Function Vista Single tap Applicable Applicable Functions as a left click of mouse Functions as a double click by quickly touching twice The pen or a finger should be set apart enough from the panel Double tap Applicable Applic
8. f the Control Panel e When operating between two points touch operation may not function correctly if the touch operation is too fast if the distance between the two points is too short or if the two points are crossing e Touch operation may not correctly function if any obstacle is between the sensor and the operating finger For more information about touch operation see the help information of Windows 10 Before Calling for Service If you think the touch panel is broken or if it is not operating correctly check the following before calling for service When using Windows XP or Vista refer also to Troubleshooting of the installation manual of the touch panel included in the supplied CD ROM For Windows XP Vista and 7 Check point Action to take No action occurs by touching Response is lost during operation Is the USB cable connected appropriately Are strong light sources or devices that use infrared rays located nearby Has the OS been started up Has setting of the computer been correctly made 1 Is the USB cable connected appropriately Is there a strong electrical noise source e g power generators air conditioners near the equipment 1 Windows 7 only Check that the USB cable is connected If using a USB hub check that the power is supplied from the USB hub Use the supplied USB extension cable Because some cables may not correctly function use the USB extension ca
9. hat use infrared rays located nearby Response is slow or there is an area where response cannot be obtained Is there a strong electrical noise source e g power generators air conditioners near the equipment Is the tool used for touch inputting thinner than a finger Is the infrared transmissive part on the screen kept untouched until the OS starts up on the computer This equipment is a touch panel using infrared rays Incident light containing infrared rays may hinder operation of the touch panel Sunlight It is not a problem as long as the infrared transmissive part of the touch panel is not directly exposed to sunlight Fluorescent light It can be a problem because some types of fluorescent light particularly inverter type produce infrared rays White candescent light It can be a problem because it contains much infrared rays Keep as long a distance as possible between the equipment and the light source or prevent the infrared transmissive part from being directly exposed to the light Device using infrared rays Malfunction may occur if a remote control or other device using infrared rays is used for the touch panel This equipment is a touch panel using infrared rays Incident light containing infrared rays may hinder operation of the touch panel Sunlight It is not a problem as long as the infrared transmissive part of the touch panel is not directly exposed to sunlight Fluorescent light I
10. he figure below adjust the position seeing from the front so that the touch panel does not lean to one side End of the screen Touch panel alignment mark Power lamp window 5 After adjusting the position completely tighten the screws which were temporarily fixed e Note that tightening the screws too tight may deform the bracket e There should not be a space between the touch panel and the front surface of the main device e Confirm that lighting of the power lamp can be seen from the power lamp window If it cannot be seen due to misalignment move the touch panel horizontally to make fine adjustment Connection with Computer USB connector type A USB connector type A Female Male Connect to the Touch panel USB port on your computer Computer ie ae USB connector type A To connect to your computer Male se the instruction manual a the main device Caution If the infrared transmissive part on the screen is shaded by your fingers or other things when connecting the USB extension cable that may be detected as a failure during initialization and if no corrective action is taken touch detection may not correctly function partially In that case disconnect and reconnect the USB extension cable At this time restarting the computer is not necessary e B
11. her abnormal conditions may cause a fire or other accidents e Stop using it immediately and contact your dealer for repair Do not repair it by yourself because doing so can be dangerous Do not place nearby a container with water or such other liquid in it e If water or other liquid is spilled on or gets inside the equipment a fire or electric shock may occur E g flower vases flower pots glass and bottles containing cosmetic liquid chemical liquid or water Prevent the equipment from getting wet e Doing so may cause a fire or electric shock Do not allow foreign materials to get in the equipment e Do not insert or let metal objects or combustible materials in the equipment because that may cause a fire or electric shock Pay special attention to children s behavior CAUTION Do not use the equipment with any other device than the main device specified in the catalog e Otherwise the unit may be dropped and become damaged and personal injury may result Installation should be performed only in the specified procedure e Incorrect installation may cause an accidental fall of the equipment resulting in personal injury Do not place the equipment in a humid or dusty location or in a location where the equipment may be exposed to oil smoke or steam e Doing so may cause a fire or electric shock Use only the special components for installation e Otherwise the main device may fall and get damaged resulting in personal inju
12. on pitch 2 5mm x 2 5 mm Power source Touch Panel Output system Coordinate output Number of optical 186 W x 222 W x 267 W x 288 W x elements 105 H 124 H 151 H 162 H Optical element pitch 5 0 mm W x 5 0 mm H Minimum stylus 7 0 mm W x 7 0 mm H USB1 1 compliant Interface Signals DATA DATA VCC GND Temperature When operating 0 40 C Temperature gradient 25 C Hr or less Humidity When operating 20 80 No dewing Resistance to external Lateral light 2000 Ix or higher 20 angle of incidence light Frontal light 10000 Ix or higher 90 angle of incidence Panel shape Flat panel Flat type External dimensions 1 028 2 mm W x 1 218 2 mm W x 1 442 2 mm W x 1 562 2 mm W x excluding projections and 618 2 mm H x 732 2 mm H x 860 2 mm H x 933 2 mm H x mounting brackets 12 mm D 12 mm D 12 mm D 12 mm D Mass Approx 2 4 kg Approx 2 7 kg Approx 3 1 kg Approx 3 3 kg Computer IBM PC AT compatible machine with USB ports Windows XP SP2 or later 32 bit or 64 bit Windows Vista 32 bit or 64 bit Windows 7 SP1 or later 32 bit or 64 bit 1 For the touch panel only when mounted to the main device it follows the conditions of the main device 13 External Dimensions External Dimensions Unit mm A 79 2 Cho K 89 t gt 47 47 12 B a 89 t 72
13. re information see the help information of Windows For Windows XP and Vista Perform calibration using the supplied driver software The touched point is displaced For calibration procedure see the installation manual of the touch panel driver software included in the supplied CD ROM Has Windows 7 been Dual touch is available only on Windows 7 Use the ___ installed in the computer computer with Windows 7 OS Dual touch is Has the touch panel drive Installing the touch panel driver on Windows 7 will E not possible ate been installed on Windows disable dual touch Uninstall the touch panel driver re because it is not necessary on Windows 7 If the problem is not solved even if the actions have been taken contact our sales office or the dealer of purchase Specifications Model Number TY TP42P30K TY TP50P30K TY TP60P30K TY TP65P30K Type Touch Panel Voltage 5V DC 10 Electric current 5V DC Max 500 mA Supply method From USB bus Detection system Infrared ray interruption detection eanehwindow 934 1 mm W x 1124 1 mm W x 1348 1 mm W x 1468 1 mm W x 524 1 mm H 638 1 mm H 766 1 mm H 839 1 mm H Deisaion range 925 mm W x 1105 mm W x 1330 mm W x 1435 mm W x g 520 mm H 615 mm H 750 mm H 805 mm H Effective detection range Above detection range 1 0 mm around all sides Resolution 1481 W x 1769 W x 2129 W x 2297 W x 833 H 985 H 1201 H 1289 H Detecti
14. ry Two or more people are required to install or remove the main device e Otherwise the main device may fall causing personal injury Tighten all the screws securely when assembling the equipment e Improper assembly may cause an accidental fall or damage of the equipment resulting in personal injury Unplug the connecting cable before moving the equipment e Failure to do so may cause an accidental fall or turnover resulting in personal injury Note for an installation technician m Please hand over these operating instructions to the customer after installation m Panasonic shall not be accountable for any accident or damage caused by incorrect installation or mishandling Maintenance Setup location Places where the touch panel should not be setup include e Locations exposed to direct sunlight and locations near powerful light sources The equipment is an optical touch panel utilizing infrared rays and may function incorrectly when adversely affected e Dusty or humid locations e Locations that may be exposed to impact or vibration e Locations near emissions of chemicals or steam or locations where contact may be made with chemicals e Locations near sources of electrical noise generators air conditioners etc Cautions when in use Do not touch the infrared transmissive area and screen until the OS starts up after f the computer is turned on eS EPN e Such an action will be detected as defective elements resulting in malfunc
15. t can be a problem because some types of fluorescent light particularly inverter type produce infrared rays White candescent light It can be a problem because it contains much infrared rays Keep as long a distance as possible between the equipment and the light source or prevent the infrared transmissive part from being directly exposed to the light Device using infrared rays Malfunction may occur if a remote control or other device using infrared rays is used for the touch panel Do not use the equipment near from a device causing much electrical noise The noise affects the power source and interface and may cause malfunction Inputting with a tool smaller than 7 mm W x 7 mm H may lower the resolution or detection speed or may not be detected After removing an obstacle reconnect the USB cable or restart the computer 11 Check point Action to take The touched Perform calibration in General of Tablet PC Settings point is ae pann of the Control Panel For more information see the displaced help information of Windows If the touch panel was removed and mounted again the mounting position may not be the same as the previous one and thus the touching position and cursor position may not match If the touch panel was removed be sure to perform calibration For Windows 7 Was the touch panel Perform calibration in General of Tablet PC Settings removed of the Control Panel For mo
16. the infrared transmissive area Failure to do so will cause a malfunction but on such an occurrence you can restore normal function simply by gently wiping the soiling off e If soiling is severe wet a cloth in neutral detergent diluted by 100 times of water wring well wipe off the soiled part and then wipe well with a dry cloth Do not directly spray or apply detergent e If liquid droplets get inside the equipment may fail Do not apply volatile materials such as insecticides benzene or thinner e The panel may get deteriorated or the coating may come off Do not keep the equipment contacted with rubber or plastic materials for a long time e The cabinet may get deteriorated e When using a chemical wipe follow the instructions supplied with it Cleaning of the inside should be performed at least once a year Consult your dealer for cleaning e If dust builds up inside the level of infrared light available for touch detection will decrease and may result in poor operation Consult your dealer for cleaning of the inside at least once a year Components Check the components and their quantities Touch panel Accessories USB extension cable Touch pen Mounting bracket A Mounting bracketB 4 for top side E gt Mounting screw A 8 ND Mounting bracket A iP for bottom side lt gt Mounting screw B 8 ir CD ROM 1 Operating Instructions e Operating Instructions e Driver software
17. tion of the area equipment Should this occur restart the computer Also when disconnecting and connecting the USB cable do not touch the infrared transmissive area and screen When using other devices utilizing infrared rays keep them away from the equipment to prevent erroneous operation Use only the touch pen included with this equipment Operation is not guaranteed with other products When using the touch panel be careful not to apply an excessive load to it by pressing the touch panel body or in any other way Cautions when moving Keep the equipment away from any impact when moving Failure to do so may result in failure Hold the main device when moving e Gripping this equipment to move may result in failure Do not hold the USB cable when moving e Doing so may damage the USB cable resulting in a failure Maintenance Be sure to unplug the USB cable before cleaning the equipment Use a soft cloth and lightly wipe off dirt on the surface of the equipment e If soiling is severe wet a cloth in neutral detergent diluted by 100 times with water wring well wipe off the soiled part and then wipe well with a dry cloth e If liquid droplets get inside the equipment as well as the screen of the main device may fail Also do not rub up the screen with strong force Use a soft cloth and wipe off dirt on the surface of the infrared transmissive area e Once a day use a soft cloth to wipe off any soiling or debris on
Download Pdf Manuals
Related Search