Chief 44U ROTR-HD
Contents
1. Instruction Sheet Raxxess ROTR HD Heavy Duty Step 1 Illustration 1 Illustration 2 Lay the rack top on a table or on the floor upside down as shown in Illustration 1 The top is about 19 x 18 x 3 1 2 as shown Lift one of the four rack rails into position in the corner of the rack and fasten it with 2 10 32 x 3 4 rack screws the screws should go through the holes in the 10 32 top and into the threaded holes in the rack rail _ RACK STUDS Leave these loose for now Then do the same for the other three lengths Step 2 Next insert 2 1 4 20 pem studs screws with really flat little heads into the side holes of the rack and again through each of the rails and T secure with the nuts provided See Illustration 2 UPSIDE DOWN FRONT REAR VIEW Now tighten all of the fasteners Be careful not to UPSIDE DOWN over tighten they don t need much torque 1 4 20 Step 3 Illustration 3 Illustration 4 Turn the top assembly over and place it on the rack as i shown Now line up 1 4 20 pem studs same headless wonders as before into the sides and the rails and secure them in place with the same nuts as before See Illustration 3 Again it is usually easier when you leave them loose until the last is in place then tighten Step 4 The cable carriers fasten to both the stationary base of the unit and the slide out portions of the rack using the same pem studs and nuts as shown in Illustration Page 1 of 3 Ins2. heet Raxxess ROTR HD Heavy Duty Illustration 8 Support Mounting Brackets Adjustable Support Cylinders Roller Assembly Protective Floor Mat Turn cylinders and watch the assembly rise up to meet the rack Illustration 9 Cabinet ee a or base Step 7 Place the floor protector about 4 in front of the rack Place the support assembly in front of the rack with the rack open about 3 4 inches The support assembly should be lower than the rack as in Illustration 8 When you turn the cylinders you will notice that the Mounting brackets raise up in one direction and lower when you turn in the other direction Turn the cylinders counter clockwise until the mounting brackets come up to the height of the matching holes in the front of the rack Note that you will need to keep the fronts of the brackets close to the rack in order to catch the Hems in the brackets under the mating brackets in the front of the unit Attach the roller assembly brackets to the front of the rack using the 4 3 8 cap screws as in Illustration 9 Tighten with the hex key supplied The unit should now roll in and out freely and when you unlock the pull ring in the front you will be able to swivel the unit to gain access to the rear See Illustration 10 When you complete the installation or servicing you can store the roller assembly under the front of the unit After closing the unit cover the mechanism with the decorative cover pla
3. te supplied attached with the 2 1 4 20 screws Illustration 10 Lock in place in either direction Overhead view Page 3 of 3
4. truction Sheet Raxxess ROTR HD Heavy Duty Flats lt a 5 Step 5 Turn Adjustable Support Cylinders TRE rack can now be attached to the floor of a cabinet or the Counter pedestal or stand that you have prepared for it Clockwise Roller Asseimbir We recommend attaching the roll out support assembly to the rack directly after doing so The Support Cylinders have left handed threads at the bottom and right handed threads at the top Thread the cylinders onto the roller assembly TURNING Illustration 6 COUNTER CLOCKWISE until they are all the way in See Illustration 5 Turn Sense eee EB Support Mounting Brackets thread onto the tops of the Clockwise cylinders as shown in Illustration 6 These will thread in the opposite direction so you should turn them clockwise until they are all the way in Step 6 You are now ready to attach the support mechanism to the rack Remove the 2 screws in the front that hold the dcorative cover plate in place and remove the plate Remember that the rack will now slide open and must be held in place to keep from doing so Nay p l I Place the rack on the platform onto which it will be Pe mounted as in Illustration 7 f NN i Bolt the rack in place VA i eee ek IMPORTANT SAFETY NOTE THE RACK MUST BE l SECURELY ATTACHED TO THE CABINET OR BASE AND Illustration 7 THE SUPPORT MECHANISM MUST BE USED AT ALL TIMES WHEN OPENING THE UNIT FOR ANY REASON Page 2 of 3 Instruction S
Download Pdf Manuals
Related Search