AMX AVS-SL-0201-834
Contents
1. af EFA Overview The Solecis AVS SL 0201 834 FG1330 1401 01 is a dual input PC interface with audio Known as the Xtra 2 because of its additional input for laptop visualiser or scaler Switching between sources can be controlled from RS232 the front panel auto switching with priority or via contact closure connection Two simultaneous main outputs are available on both BNC and HD 15 connectors The outputs are both 75 ohm driven with TTL sync restore for connection to long cable runs The audio inputs follow the video and are converted to balanced or unbalanced outputs The AVS SL 0201 834 may be used as a Single Input Interface or a 2 Input Switcher front SOLECIS AVS SL 0201 834 Me DT gi uy CONTA z5 or c 00000 FIG 1 Solecis AVS SL 0201 834 Product Specifications Solecis AVS SL 0201 834 Specifications Number 2 e Channel B 250MHz 3dB RGB Connectors e 5x BNC e 1x HD 15 Connectors Level Max Level Max Level Connector Type Max Level Impedance RGB Video Bandwidth RGB Return Loss Installation Guide Solecis AVS SL 0201 834 Solecis AVS SL 0201 834 Specifications Cont Switch e Contact closure e Auto switch e Front panel RS232 Input Voltage 9 12VDC Dimensions HWD 1 86 x 9 10 x 4 69 47 2 mm x 231 1 mm x 119 1 mm e Height includes feet e Depth includes connectors 28 bs T310 Included Accessories PS4 4 power supply FG2. 423 44 e CE e FCC class B part 15 e ROHS WEEE compliant Connectors Type Certifications Safety Instructions Please read these instructions before using your AMX Solecis device Failure to comply with these instructions could result in fire electrical shock personal injury death or damage to the equipment Liquid Spills Do not set drinks on top of the unit or immerse the unit in liquid Do Not Disassemble This device contains no user serviceable parts All servicing must be performed by a qualified service technician For Safety Reasons e Do not place the unit on an unstable surface e Do not use near water or sources of heat e Use only recommended attachments e Use the type of power supply as specified Unplug the power to the unit and refer servicing to qualified personnel under the following conditions If liquid has been spilled or the unit has been exposed to rain or water fit does not operate normally when the operating instructions are followed or if it exhibits a distinct change in performance indicating a need for service e Ifthe unit has been dropped or the cabinet damaged Computer Connections Audio Connection Connect the sound output from the Computer to the sound input corresponding to the input the video signal is connected e Use a 3 5m stereo jack cable Display Connection The video signal from the unit outputs on BNC and HD 15 Connect the output from the unit to the Input of a proj
3. ector or monitor using approved 75ohm coax cable The unit may be used to drive 2 display devices Video Pin Connections RS232 Mode FIG 2 provides the pin layout for the RGBHV HD 15 connectors 1 Power unit down 2 Set Dip switches as shown in the Rear Panel DIP Switches table 3 Connect RS232 cable to Control pins as follows e TX Pin A RX e GND Pin B GND 4 Power up unit Set System Protocol as follows FIG 2 RGBHV HD 15 connector Baud 9600 e Data 8 Bits The pin configuration for the HD 15 video connector are as follows Stop 1 Bit D i T a romance 3 BLUE 44 nie Note Numbers are shown in HEX 4 n c 12 n c 5 n c 13 H SYNC 6 RED GROUND 14 V SYNC 7 GREEN GROUND 15 n c 8 BLUE GROUND Switching On Equipment Connect the unit to a Mains power source and turn on at the Mains Either the Input A or Input B button will illuminate to indicate the unit has powered up Setting Up the Mode of Operation Note When an RS232 cable is connected to the Control socket all other Rear Panel DIP Switches functions will be disabled cowo e eT Auto Switch Normal Manual Switch Front Panel a Set Dip switches as shown in the Rear Panel DIP Switches table Auto Switchin Auto Switch Normal Last Detected Input J The unit scans the VERTICAL sync inputs of input A and B If any signal ft 0 U Auto Switch Priority hy Input B Priority sources are active the unit will switch to the last detected
4. input Contact Closure Contact Closure Momentary NU A NU MU Bet Button Toge Bell Button Bell Button Togge To switch between two active sources either disconnect the source and reconnect or use the laptop video toggle mode to turn the Video output off then Contact Closure ama feee Logic State Closed Input A on again usually by holding the FN key with a Function key Latening To operate in auto switch mode with manual override switch Manual dip down RS232 e tlel e Serial Control to the On position fT switch up U switch down amp function disabled fT 4 switch up or down Auto Switch Priority 1 Set Dip switches as shown in the Rear Panel DIP Switches table 2 When a signal is applied to Input A the unit will automatically switch to A e 1 Manual Switch Off On 3 When the signal is removed from Input A the unit will switch to Input B 4 e 2 Remote Control Off On To operate in auto switch mode with manual override switch Manual dip e 3 Auto Switch Off On down to the On position e 4 Auto Switch Normal Priority Manual Switch Front Panel Operation 1 Power up switcher 2 The Green LED A will light to indicate power present and A Input is switched 3 Set Dip switches as shown in the Rear Panel DIP Switches table 4 Press INPUT SELECT button to change between Input sources Contact Closure Switch Functions Toggle Switch Set Dip switches as shown in the Rear Panel DIP Switches table e A
5. momentary switch can be wired across connections A and B on the rear panel e Manual and auto switch can also be enabled or disabled in this Toggle mode of operation Latching Set Dip switches as shown in the Rear Panel DIP Switches table e With control pins A and B open the unit will switch to Input B e When control pins are closed the unit will switch to Input A Note When Dip switch 2 is set to Latch or RS232 all other functions will be disabled For full warranty information refer to the AMX Instruction Manual s associated with your Product s 93 1330 1401 01 REV D 12 08 TT AINI BRIANNA NENIAN ANIDA AAAA D 2008 AMX All rights reserved AMX and the AMX logo are registered trademarks of AMX AMX reserves the right to alter specifications without notice at any time bBatg 3000 RESEARCH DRIVE RICHARDSON TX 75082 800 222 0193 fax 469 624 7153 technical support 800 932 6993 www amx com f
Download Pdf Manuals
Related Search