Gefen EXT-HDMI-2-HDSDIS video switch
Contents
1. The following are the buttons for the RMT 8HDS IR UP Navigates cursor up LEFT Navigates cursor left Enter Accept Operation Return to Menu RIGHT Navigates cursor right DOWN Navigates cursor down MENU Show Hide Onscreen Display OUTPUT Change Output Format SOURCE Non operational To bring up the onscreen menu press the MENU button Navigation is done using But tons up left right and down Push the Enter button to accept the cursor focus Pressing the Output button cycles through the following output modes 480i 576i 720p 1080i Other functions and output modes can be accessed through the onscreen menu To Restore I O settings simply recycle power on the Scaler Note Both dip switches under the remote battery cover must initially be in the OFF position to communicate with the Scaler RMT 8HDS IR INSTALLATION 1 Remove battery cover from the back of the RMT 8HDS IR remote 2 Verify that dip switches 1 amp 2 are in the down OFF position 3 Insert the battery hold the battery so that you can see the positive side facing up The side that is not marked must be facing down 4 Test the RMT 8HDS IR remote by pressing ONLY one button at a time The indicator light on the remote will flash once each time you press a button WARNING Do not press multiple buttons simultaneously and do NOT press buttons rapidly These actions will cause the remote to reset and steps 1 4 will have2. HDMI to HD SDI Scaler USER MANUAL oe e WWW gefen e LST ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday through Friday Write To Gefen Inc c o Customer Service 20600 Nordhoff Street Chatsworth CA 91311 www gefen com support gefen com Notice Gefen Inc reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice The HDMI to HD SDI Single Scaler is a trademark of Gefen Inc 2008 Gefen Inc All Rights Reserved 10 11 TABLE OF CONTENTS Introduction Features Panel Descriptions Menu Functions Menu Functions Continued Supported Input Output Resolutions Operation Notes RMT 8HDS IR Installation Firmware Update Procedure Specifications Warranty INTRODUCTION The HDMI to HDSDI Scaler is the newest revision of our HDSDI conversion line incorporating HDMI conversion scaled to your choice of SD HDSDI Single or Dual link modes Resolutions of up to 1080p are supported over the HDSDI link for those that want true High Definition Support for HDMI embedded audio is supported Performance has been greatly enhanced due to Gennum s VXP Scaler onboard allowing for new features such as Genlock Color amp Gamma Correction Noise Reduction Detail Enhancement Aspect Ratio Selection Pattern Generator Mode
3. Locks output clock with Ref clock Language Set menu to display English or French text Patterns Color Bars Display color bar video pattern Cross Hatch Display cross hatch video pattern General Firmware Version Kernel Version Configuration Version FPGA Version Save Config Restore Default Config SUPPORTED INPUT OUTPUT RESOLUTIONS Input Video Formats Supported 720p 50 1080p 23 98 2K p 23 98 480p 720p 59 94 1080p 24 2K p 24 576i 1080p 25 el 576p rr Donan 1080p 29 97 1080p 30 Ss 720pi24 Dong mme 2025 Donn men 720p 29 97 Um0sgn 1080p 59 94 720p 30 sf toov60 ss 1080p 60 d o Input Graphic Formats Supported 640x480 75 1152xe64 75_ 1366x923 50_ 640x480 85 1280x768 60_ Dupong 800x600 60 1280x960 60_ 1440xt08o e0 800x600 75 1280x960 85 1600x1024 i Oo 800x600 85 1280x1024 60 1600x1200 60 1024x768 60 1280x1024 75 1680x1050 60 Output video formats supported 720p 50 1080p 23 98 1080sf 23 98 480p 59 94 720p 59 94 1080p 24 1080sf 24 20p 60 1080p 25 1080sf 25 576p 50 035i 59 94 1080p 29 97 1080sf 29 97 720p 23 98 0351 60 1080p 30 1080sf 30 720p 24 080i 50 1080p 50 2K p 23 98 720p 25 080i 50M 1080p 50M 2K p 24 720p 29 97 080i 59 94 1080p 59 94 2K sf 23 98 720p 30 080i 60 080p 60 2K sf 24 OPERATION NOTES On power up the HDMI to HDSDI Scaler will automatically detect the input format of the input The unit is controlled using the included remote
4. amp Multiple Language Menu Support Bottom Line More performance less cost HOW IT WORKS HDMI devices are connected to the HDMI input and SDI devices are connected to the SDI output When the source display and the Scaler are powered and connected video signals are converted to the proper format CONTENTS The HDMI to HD SDI Scaler SL package consists of HDMI to HDSDI Scaler 5v Power Supply RMT 8HDS IR Users Manual FEATURES e 10 bit resolution for greater precision and dynamic range Proprietary 10 bit motion adaptive video de interlacing with edge interpolation for HD SD formats Advanced noise reduction and detail enhancement Max active image size of 2048 samples x 2048 lines PBP processing for various combinations of video and graphics with alpha blending Fully integrated sprite based multi plane OSD controller Frame rate conversion to from any refresh rate Pattern mode w color bars amp coarse hatch patterns Color correction Noise Reduction Detail Enhancement Brightness Adjustment Gamma Selection Aspect Ratio Select Custom Timing output mode French English Menu Set RS 232 upgradeable firmware RS 232 and or IR Control Genlock onboard PANEL DESCRIPTIONS Infrared Eye Power Indicator Light HOM I 2 HOSDI Made In U S A efen Inc HDMI Input Genlock HD SDI Input 5V Power j Output Connector RS 232 Uplink Port MENU FUNCTIONS Aspect Full Screen Stretches input
5. o Detect by default Signal can be forced to a specific High definition resolution Please see Supported Input Output Resolutions for more information Input Graphic Format Auto Detect by default Signal can be forced to a specific High definition resolution Please see Supported Input Output Resolutions for more information Link Configuration When using dual link SDI HDSDI input allows you to select either YCbPr or RGB color spaces MENU FUNCTIONS CONTINUED Input Menu Continued Clean Aperture Horizontal and Vertical Size Stretch image Horizontally or Vertically Horizontal and Vertical Position Move image in view port Horizontally or Vertically Remote Channel Changes the IR code of the HDMI to HDSDI Scaler to one of 4 different settings between 0 and 3 When the remote channel is changed dip switches in the 16 button remote must be changed to the corresponding code in order to continue operating the HDMI to HDSDI Scaler Please see RMT 8HDS IR Installation page for more information Non Standard Sync Allows the box to sync to non standard video formats Output Video Output Format Select the desired HD output resolution Please see Supported Input Output Resolutions for more information Link Configuration When using dual link SDI HDSDI input allows you to select either YCbPr or RGB color spaces Genlock Off Freerun mode Video Input Locks input clock in sync with output clock Ref Input
6. to be repeated Note The RMT 8HDS IR ships with two batteries One battery is required for operation the second battery is complimentary The following are the dip switch combinations that correspond to the Remote Code menu option on the HDMI to HDSDI Scaler Please see Menu Functions section for more information Remote Channel 0 Remote Channel 1 Remote Channel 2 Remote Channel 3 RS 232 INTERFACE FIRMWARE UPDATE PROCEDURE The HDMI to HDSDI can be controlled via IR remote and through the RS 2323 Uplink port Check the download section on our website for firmware updates and information on how to control this unit Go to http www gefen com kvm support download jsp_ to find the necessary documents and files SPECIFICATIONS NUE Video Bandwidth rocessar icp sect Gecdeceetestenndeseeieacacneecce 1 65 Gbps OQ tp t Vid o Babette EE 2x 1 485 Gbps Maxim m Input eege 2048x1080 Maximum Output ResolutlOncnicicsccticrcreneitccci eects 1080p with Dual Link HD SDI el RR ET type A 19 pin female SEENEN BNC female Dee Serial RS 232 POWEP EE DV DC Power Gons mptior s saer aaae 20 watts Max Run u E E 8 25 W x 1 75 H x 7 5 H SNIPHNG le EE 5 Ibs 10
7. to fill the Monitor Letter Pillar Box Sets the aspect ratio to fit a letter or pillar box format Panoramic Panoramic Zoom feature Extract Feature to magnify the signal Exact Size Adjusts signal magnification Horizontal Vertical Position Moves the magnified signal Horizontally and Vertically Through Feature to crop the signal Horizontal Vertical Size Horizontally and Vertically contracts or expands the cropping viewport Horizontal Vertical Position Move the signal Horizontally or Vertically inside the cropping viewport Two Screens Option becomes available if using Dual Link HDSDI Layout Size and Position Horizontal Vertical Size Adjust Horizontal or Vertical resolution Horizontal Vertical Position Move image Horizontally or Vertically Picture Image Color Contrast Individually adjust the contrast for red green and blue Brightness Individually adjust the brightness for red green and blue Black level Adjust black levels between 0 default and 100 Gamma Correction Default Set for Default Gamma settings SRGB Custom Enables Gamma Coefficient menu item as the current Gamma coefficient Gamma Coefficient 0 3 3 0 Default set at 1 0 User Table Detail Enhancement Detail Enhancement Digitally enhance signal Noise Threshold Adjusts noise allowed in detail enhancement Noise Reduction Digitally reduce signal noise Motion Threshold Input Input Video Format Aut
Download Pdf Manuals
Related Search