Gefen EXT-DVI-1600HD
Contents
1. DVI 1600HD Extender EXT DVI 1600HD User Manual 4 NwWw gefen com HIGH DEFINITION MULTIMEDIA INTERFACE DT Blu ray Disc ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday thru Friday Write To Gefen Inc c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefen com support gefen com Notice Gefen Inc reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice DVI 1600HD Extender is a trademark of Gefen Inc 2008 Gefen Inc All Rights Reserved All trademarks are the property of their respective companies Rev X2 N nN 11 12 13 CONTENTS Introduction Operation Notes Features Sender Unit Panel Layout Sender Unit Panel Descriptions Receiver Unit Panel Layout Receiver Unit Panel Descriptions Connecting The DVI 1600HD Extender Connecting And Operating The DVI 1600HD Extender Specifications Warranty INTRODUCTION Congratulations on your purchase of the DVI 1600HD Extender Your complete satisfaction is very important to us Gefen Gefen delivers innovative progressive computer and electronics add on solutions that harness integration extension distribution and conversion technologies Gefen s reliable plug and play products supplement cross platform2. 1600HD Sender unit The result will be HDMI with embedded audio at the Receiver end The digital input jacks can only support D PCM or PCM stereo audio formats OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE DVI 1600HD EXTENDER DVI 1600HD Extender uses 4 strands of LC terminated f ber optic cable Single mode and multi mode fber optic cable types are both supported DVI and HDMI modes for HDCP are available and are selectable via a switch located on the front panel of the DVI 1600HD sender unit Analog stereo digital S PDIF and digital TOSLINK inputs are all available for input but only one is selectable for transmission to the receiver The selected audio input will be replicated out of all three audio outputs on the receiver unit HDMI mode supports HDCP with resolutions up to 1080p Full HD Both single and multi mode cables are supported at distances up to 650 feet 200 meters DVI mode does not support HDCP with resolutions up to 1920 x 1200 Both single mode and multi mode cables are supported Multi mode f ber can support distances of up to 1640 feet Single mode f ber can support distances of up to 6560 feet 2 kilometers HDMI 1 2 compliant FEATURES AAAA Features e signal integrity and best image over long distances e Fiber optic transmission medium eliminates electromagnetic interference EMI during send or receive operations e Lightweight rugged cabling an
3. computer systems professional audio video environments and HDTV systems of all sizes with hard working solutions that are easy to implement and simple to operate The Gefen DVI 1600HD Extender The Gefen DVI 1600HD is a perfect solution for extending and managing control systems at great distances The Gefen DVI 1600HD sends DVI or HDMI Audio and RS232C signals up to 300m away when used with DVI at 1920x1200 and up to 2km when used with DVI at lower resolutions It maintains HD video signals up to 1920x1200 with computers and 1080p with HD equipment Additionally extension of RS232 signals helps create long distance control systems for AV integration or touch panel systems How It Works The Gefen DVI 1600HD system uses a send and receive methodology The DVI HDMI Audio RS232C source devices are plugged into the Sender module At the Receiver remote devices including an HD display plug into the Receiver module The proper length of f ber optic cable is connected at both ends Power supplies for the modules are plugged into wall sockets and a crisp vibrant HD picture results Note This device fully supports Display Data Channel DDC and High Bandwidth Digital Content Protection HDCP when the front panel switch on the sender module is selected to HDMI The Gefen DVI 1600HD uses a DVI connector for video HDMI can be sent by using adapters or combo cables to provide DVI video with external digital audio as combined input to the DVI
4. D will become active when the 12V DC power supply has been properly connected to the unit and an open wall power socket Analog Stereo Audio Output This output will supply analog stereo audio to one pair or RCA audio inputs on a device This input will always be active when a 2 channel source analog or digital is selected on the sender S PDIF Digital Audio Output This output will supply digital audio to a S PDIF coaxial audio input device This input will always be active when a 2 or multi channel source analog or digital is selected on the sender Optic Digital Audio Output This output will supply digital audio to a TOSLINK optical audio input device This input will always be active when a 2 or multi channel source analog or digital is selected on the sender RS 232 Serial Communications Input This port is capable of 2 way serial communication between RS 232 devices connected to the sender and receiver This port can be connected to a serial communications device for interaction with a computer via an RS 232 serial communications cable connected to the sender 11 12 13 RECEIVER UNIT PANEL DESCRIPTIONS DVI Output This output will accept a DVI or HDMI with a DVI to HDMI adapter cable capable device Fiber Optic Input A This connector accepts a pair of LC terminated f ber optic cable that will link the sending and receiving unit together When the cables between this port and the corresponding ports on the rec
5. NK optical digital audio Input Connector digital video 1 x DVI 29 pin Female Output Connector analog audio 1 x Pair RCA L R stereo Output Connector digital audio 1 x S PDIF digital audio Output Connector digital audio 1 x TOSLINK optical digital audio Output Connector digital video 1 x DVI 29 pin Female RS232 Connectors Input Output 9 pin Serial Female Link Connectors 4 strand LC LC f ber optic cable single or multi mode Input Video Signal Voltage 1 2 Volts p p Input DDC Signal Voltage ocooocconccoccccnccoonnononnonononnnnonnonnnons 5 Volts p p TTL Power Supply Power Consumption 12V DC x 2 72 Watts total Dimensions 10 3 W x 1 2 H x 5 1 D Operating Temperature usa esse een 0t050C Relative Humidity ee een 10 85 SNIPPING Well 5 lbs 12
6. d connectors Cost effective per foot meter e power consumption at 72W total e Plug and play installation ease no software drivers e Can use both Single and Multimode optical f ber cables e Maximum range of 2km for DVI 200m if sending DDC HDMI with HDCP e _ 5232 signal extension helps create long distance control systems for A V integration Package Includes 1 Gefen DVI 1600HD Sender 1 Gefen DVI 1600HD Receiver 1 6 Foot DVI Video Cable M M 1 6 Foot DB9 RS 232 Cable M F 1 12V DC Power Supply 1 User s Manual SENDER UNIT PANEL LAYOUT Front Panel Back Panel 10 SENDER UNIT PANEL DESCRIPTIONS DVI HDMI Mode Selector Switch This switch will set the video mode DVI mode is intended for use with computers and will support resolutions of up to 1920 x 1200 HDMI mode is for use with consumer HDMI devices and supports HDCP and resolutions of up to 1080p Full HD There are also distance limitations associated with the different modes Please see page 10 for details Audio Input Selector Button This button is used to select the audio input source There are three input options Audio analog stereo Coax digital S PDIF Optical digital TOSLINK Each press will cycle through these selections Audio Selection LED Indicator This LED will be active when the Audio analog stereo audio source has been selected Coax Selection LED Indicator This LED will b
7. e active when the Coax digital S PDIF audio source has been selected Optical Selection LED Indicator This LED will be active when the Optical digital TOSLINK audio source has been selected Reset Button This button is used to cycle the power off and on In most cases this will force the source to re establish a link with the endpoint device This will also force the source to re read the EDID Optic B LED Indicator This LED will indicate the status of the connection between the sender and receiver s 2 pair of LC f ber optic cables labeled Optic This LED will be active when a valid link between the sender and receiver has been established Status LED Indicator This LED will indicate the status of the unit and will be active when all devices are properly connected and indicates that the unit is working within specif cation Optic A LED Indicator This LED will indicate the status of the connection between the sender and receiver s 2 pair of LC f ber optic cables labeled Optic A This LED will be active when a valid link between the sender and receiver has been established Power LED Indicator This LED will become active once the included 12V DC power supply has been properly connected between this unit and an available wall power socket 11 12 13 14 15 16 17 18 SENDER UNIT PANEL DESCRIPTIONS 12V DC Power Input Connect the included 12V DC power supply to this input The Power LED will become active whe
8. eiver are properly connected the LED indicator labeled Optic A on the front panel of both units will become active Fiber Optic Input B This connector accepts a pair of LC terminated f ber optic cable that will link the sending and receiving unit together When the cables between this port and the corresponding ports on the receiver are properly connected the LED indicator labeled Optic B on the front panel of both units will become active CONNECTING THE DVI 1600HD EXTENDER How to Connect the DVI 1600HD Extender Connect the DVI or HDMI using a HDMI to DVI adapter cable to the DVI 1600HD Extender sending unit using a user supplied cable NOTE If the source device is a HDMI device that requires HDCP please set the DVI HDMI mode selector switch to HDMI The unit s distance will be limited to 650 feet 200 meters on 4 LC single or multi mode f ber optic cables while in this mode Connect up to 3 audio sources to the sending unit using user supplied cables Input options are as follows Analog stereo using one pair of RCA analog stereo cables Digital coaxial using one S PDIF digital coaxial audio cable Digital optical using one TOSLINK digital optical audio cable Optionally connect an RS 232 device to the sender unit using a user supplied RS 232 cable NOTE The DVI 1600HD Extender system will not cross the transmit and receive lines as a null modem adapter would All pins will pass straight through from one point to the oth
9. er Connect 2 pairs 4 strands of LC terminated single or multi mode f ber optic cables to the sender unit Connect the opposite ends of the f ber optic cabling to the receiver unit s f ber optic receptacles Connect a DVI or HDMI using a DVI to HDMI adapter cable capable device to the DVI output of the DVI 1600HD Extender receiving unit using a user supplied cable Connect up to 3 of the audio outputs to audio receiving devices Available outputs are as follows Analog stereo using one pair of RCA analog stereo cables Digital coaxial using one S PDIF digital coaxial audio cable Digital optical using one TOSLINK digital optical audio cable NOTE All outputs are active regardless of the selected input on the sender However multi channel content that is being sent by the digital connectors will not be output by the analog stereo output Optionally connect an RS 232 device to the receiver unit using a user supplied RS 232 cable 10 CONNECTING AND OPERATING THE DVI 1600HD EXTENDER How to Connect the DVI 1600HD Extender 8 Connect the included 12V DC power supplies to both the sending and receiving units and open wall power sockets 9 Power on the endpoint device frst and then the source device Operating the DVI 1600HD Extender The DVI 1600HD can be set in either DVI or HDMI mode e DVI mode has a maximum range of 6560 feet 2 kilometers with single mode f ber optic cable and a range of 1640 feet 500 meters using m
10. n the 12V DC power supply has been properly connected to the unit and an open wall power socket Analog Stereo Audio Input This input will accept analog stereo audio from one pair or RCA audio cables This input corresponds to LED labeled Audio on the front panel S PDIF Digital Audio Input This input will accept digital audio from a S PDIF coaxial audio cable This input corresponds to LED labeled Coax on the front panel Optic Digital Audio Input This input will accept digital audio from a TOSLINK optical audio cable This input corresponds to LED labeled Optical on the front panel RS 232 Serial Communications Input This port is capable of 2 way serial communication between RS 232 devices connected to the sender and receiver This port can be connected to a computers serial communications port for interaction with a RS 232 serial communications device connected to the receiver DVI Input This input will accept a DVI or HDMI with a HDMI to DVI adapter cable source device Fiber Optic Input A This connector accepts a pair of LC terminated f ber optic cable that will link the sending and receiving unit together When the cables between this port and the corresponding ports on the receiver are properly connected the LED indicator labeled Optic A on the front panel of both units will become active Fiber Optic Input B This connector accepts a pair of LC terminated f ber optic cable that will link the sending and receiving unit t
11. ogether When the cables between this port and the corresponding ports on the receiver are properly connected the LED indicator labeled Optic B on the front panel of both units will become active RECEIVER UNIT PANEL LAYOUT Front Panel Back Panel 10 RECEIVER UNIT PANEL DESCRIPTIONS Reset Button This button is used to cycle the power off and on In most cases this will force the source to re establish a link with the endpoint device This will also force the source to re read the EDID Optic LED Indicator This LED will indicate the status of the connection between the sender and receiver s 2 pair of LC f ber optic cables labeled Optic This LED will be active when a valid link between the sender and receiver has been established Status LED Indicator This LED will indicate the status of the unit and will be active when all devices are properly connected and indicates that the unit is working within specif cation Optic A LED Indicator This LED will indicate the status of the connection between the sender and receiver s 2 pair of LC f ber optic cables labeled Optic A This LED will be active when a valid link between the sender and receiver has been established Power LED Indicator This LED will become active once the included 12V DC power supply has been properly connected between this unit and an available wall power socket 12V DC Power Input Connect the included 12V DC power supply to this input The Power LE
12. ulti mode f ber optic cable DVI mode does not support HDCP Maximum supported resolution is 1920 x 1200 To select this mode set the DVI HDMI mode selector switch on the front panel of the sender to DVI e mode has a maximum range of 650 feet 200 meters with both single and multi mode f ber optic cables HDMI mode does support HDCP Maximum supported resolution is 1080p Full HD To select this mode set the DVI HDMI mode selector switch on the front panel of the sender to HDMI The audio source used for transmitting to the receiver can be selected from the front panel of the DVI 1600HD Extender sending unit Use the audio input selector button to cycle between the 3 available inputs The inputs are cycled as follows 9 analog stereo Coax digital S PDIF Optical digital TOSLINK 7 All audio outputs on the receiver are constantly active This means that analog signal are converted to digital and digital signal are converted to analog The only exception to this is multi channel digital audio which will not be output through the analog stereo output 11 SPECIFICATIONS Video Amplif Bandwidth u 2 165 MHz Maximum Resolution uscar ici 1920x1200 1080p Input Connector analog 1x Pair RCA L R stereo Input Connector digital audio 1 x S PDIF coaxial digital audio Input Connector digital audio 1x TOSLI
Download Pdf Manuals
Related Search