Pyle PDWM8300 microphone
Contents
1. SYSTEM Unit Specification Frequency range Frequency stability Modulation Frequency response T H D Distance Temperture Reciever Receiving system Sensitivity Removing weight Audio output Output connection Power supply 170 270 MHz VHF band 0 005 FM 40Hz 18KHz 3dB 0 8 50 100M 10 55 c Quartz crystal frequency 10UV 40DB emf 50ms 0 0 35Vp p 5k 16 3 mm plug DC 12 17 V NNN 1 Please take the following working flow diagram for reference on using this machine connect the mix out of receiver with mic input on the amplifier or out A B C D and mic input on the amplifier 2 Power 220V switch the power set the volume of your sound equipment 3 Adjust the volume in right sound make MIC1 and MIC2 harmony which will make you enjoying the sound well 4 Please plug out the power if you will not use the machine long time System connection flow diagram RECIEVER gt MIXER gt AMPLIFIER KAROKE AMPLIFIER Installation of reciever e Keep the machine 1m above the ground e Keep the machine away 1m against the wall e Pull the antenna up rightness fully e Make the transmitter point to the antenna without barrier Keep the reciever away any digital equipment such as CD VCD PC or other radio equipment FUNCTION DESCRIPTION TECHNICAL PARAMETERS Front Panel 4 WAYS vernon jz 3 4 MICROPHONE SYSTEM 12. IMPORTANT Pack carefully in original package if possible We are not responsible for damage incurred in returning items for repair A letter stating your exact street addres daytime phone number and the problem you are experiencing should be included You must also enclose a copy of the original receipt a sproof of date of purchase A are a E L i i nea T kaii i cy l i a Ma na te Jani reed z voLUMe iat me a outa i i pe T s B oe Professional rence Desktop VH Fu Brooklyn NY 11204 aWireless Microphone System 1 800 444 5671 ey Monday Through Thursday 9AM to 5PM Friday 9AM to 1PM Eastern HOJ yleau diro corm OW Opp yleau LO CONT TROUBLESHOOTING Some corem problems and their solutions are identified in the table below If you are unable to solve a problem contact your dealer oen ee ee o Make sure the transmitter POWER switch is ON and the receiver is plugged into a power source Nosound RF light s Check battery Check receiver squelch setting Check receiver antenna connection s o Make sure antennas are in line of sight of transmitter not glowing No sound Turn up receiver audio VOLUME control RF lights glowing Check for proper connection between receiver and karaoke unit 9 Check battery o Remove local Sources of RF interference Ifusing a guitar or other instrument check connections contains extraneous sounds Two transm
3. Lote OOO 1 Power switch 2 Power indicator 3 Volume adjust 4 Receiving indicator 4ways o O00000 Q o 1 2 2 2 2 3 4 5 1 1 Antenna 2 Audio output 3 mixed balance output 4 balanced output 5 DC power NNN Handheld Transmitter Radio output power Antenna Pre weight Cartridge Battery consumption Battery life Temperature range Body packing transmitter Radio output power Carrying frequency Pre weight Cartridge Battery consumption Battery life Temperature range gt 20mW Hide inside 50 uS Moving dynamic coil lt 30MA 8 H time of duration 10 55 j gt 20mW below the min carrying frequency 40dB 50 uS condenser lt 30mA 8 H time of duration 10 55 TECHNICAL PARAMETERS TECHNICAL PARAMETERS Wireless meeting microphone Handheld transmitter This circle light is working indicating the battery working when the f transmitter is switched on SH Domo E Power supply DC9V Power consumption lt 35mA te g g Carrying frequency 170 270MHz o Frequency stability 0 002 Head net Low voltage indicator S N ratio gt 90dB Power switch 9V Battery Channel interference ratio gt 80dB Power light Battery cover Dynamic range gt 80dB T H D lt 3 Cartridge Condenser noise proof Polarity Uni direction Frequency response 40Hz 18KHz 3dB Sensitivity of transmission 47 3dB 1KHz scsi Winaiaka Tem
4. itters may be operating on the same frequency Locate and turn one off sounds with transmitter on Signal may be too weak Repositior antennas If possible move them closer to transmitter Received signal is noisy c o Adjust receiver squelch control Remove local sources of RF interference o Reposition receiver or antennas Noise from receiver with transmitter off Momentary loss ofsoundas Reposition receiver and perform another walkthrough test and observe the transmitter is moved around RF indicators If audio dropouts persist mark these dead spots in performing performing area area and avoid them during performance NNN FOREWORD Thanks for purchasing our excellent wireless meeting microphone products please read this instruction carefully so that you can understand how to operate the product you bought correctly please store this book in the safe place for reference in future Main features 1 Using VHF 170 270 Mhz band to avert interferencing frequency 2 Using multilevel high frequency and mid frequency narrowband filter so as to dispel any possible interferencing signals 3 A specially designed circuit switch is on the phone ltis for clearing up waves of miscellaneous signals 4 All use quartz crystal oscillating circuits so the frequency is very steady 5 With audio compressing expanding technology the machine can lower noises and increase the dynamic range It can also lower reecho 6 I
5. perture 10 55j e collar line 1 Please put the battery in the battery case correctly with right poles 2 Working when the switch on mute at ST BY 3 Please out out the battery and switch off if you will not use 4 Power and low voltage two color indicator 4 Please change the battery when the low voltage lightis on 1 Cartridge 2 Workingindicator 3 Switch NN Li i
6. t has channel separate outputing and mix outputing and it can be connected with the sound adjusting stage and the karaoke enlarge 7 Special tone key locked identity functions to avoid interference signal from outside open the mute system 8 There are mulriple noise detect circuit multi circuits Soit has strong anti jamming specialty 9 Uniform cardioid pickup pattern isolates the main sound source and minimizes background noise 10 Effective built in soherical wind and pop filter 11 Longest distance in open 100m Idealest distance in open 50m Cautions 1 Please ensure the host receiver in the place where is in good condition for signal without dead angle 2 Please keep the transmitter of microphone from throwing casting and so on protecting from broken 3 The reciever without water proof so please keep it from water or something like this 4 Please keep distance with or away electromagnetic field high voltage power net or big metal subjects 5 Please switch off the transmitter when you change the battery 6 Please put out the battery if you will not use the microphone for long time 7 Please plug out the reciever if you will not use the microphone for long time 8 Please get contact with the distributor of the products if there is problem on broken or something inside 9 Please note we will not provide the service of repair if customer open it by themself without notice ii TECHNICAL PARAMETERS
Download Pdf Manuals
Related Search