Samsung SCD-2080EB
Contents
1. Do not install in a location subject to high temperature over 50 C low temperature below 10 C or high humidity Doing so may cause fire or electric shock If you want to relocate the already installed product be sure to turn off the power and then move or reinstall it Remove the power plug from the outlet when then there is a lightning Neglecting to do so may cause fire or damage to the product 5 Keep out of direct sunlight and heat radiation sources It may cause fire 6 Install it in a place with good ventilation 9 Avoid aiming the camera directly towards extremely bright objects such as sun as this may damage the CCD image sensor Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids Such as vases shall be placed on the apparatus The Mains plug is used as a disconnect device and shall stay readily operable at any time 10 Do not expose the camera to radioactivity Radioactivity exposure may damage the CCD English 5 NOLLVINHOHNI AL34VS O safety information FCC STATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation CAUTION This equipment has been tested and found to comply with the limits for a Class A digital2. SAMSUNG TECHWIN High Resolution Varifocal Dome Camera SCD 2080E User Manual SCD 2080E High Resolution Varifocal Dome Camera User Manual Copyright 2010 Samsung Techwin Co Ltd All rights reserved Trademark SAMSUNG TECHWIN EP is the registered logo of Samsung Techwin Co Ltd The name of this product is the registered trademark of Samsung Techwin Co Ltd Other trademarks mentioned in this manual are the registered trademark of their respective company Restriction Samsung Techwin Co Ltd shall reserve the copyright of this document Under no circumstances this document Shall be reproduced distributed or changed partially or wholly without formal authorization of Samsung Techwin Disclaimer Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document but no formal guarantee shall be provided Use of this document and the subsequent results shall be entirely on the user s own responsibility Samsung Techwin reserves the right to change the contents of this document without prior notice Warranty If the product does not operate properly in normal conditions please let us know Samsung Techwin will resolve the problem for free of charge The warranty period is 3 years However the followings are excluded If the system behaves abnormally because you run a program irrelevant to the system operation Deteriorated performance or natural worn out in process of t
3. such as vases shall be placed on the apparatus 7 important safety instructions English 7 contents INTRODUCTION INSTALLATION CONNECTION SETUP TROUBLESHOOTING SPECIFICATIONS 8 contents 10 11 12 15 16 16 17 18 18 31 32 34 Features What s included Component names and functions Installation Adjust the panning and tilting while watching the monitor Connecting to Monitor Connecting to Power Using Coaxial Communications Menu Configration Menu Setup Troubleshooting Specifications Dimension introduction FEATURES High Resolution By adopting a diagonal 6mm 1 3 410 000 NTSO pixel 470 000 PAL pixel SONY CCD the camera produces clear picture quality with a horizontal resolution of 600 TV lines in color mode Excellent Sensitivity The built in high sensitivity COLOR CCD produces a clear image Color 0 15Lux 50IRE F1 2 0 0003LUX SENS UP x512 SSNR3 Samsung Super Noise Reduction Function The high performance W V DSP chip effectively removes low light gain noise and afterimage to provide clear images even in dark environments Electrical Day amp Night This camera has a function that automatically selects the mode that is appropriate for daytime or night time conditions NOLLONGOHINI Motion Detection Since the camera detects motion without any additional external sensor you can monitor activity more efficient SSDR Samsung Super D
4. 600TVL Min Illumination COLOR 0 15 Lux F1 2 0 0003Lux SENS UP x512 S N Y Signal 52dB Weight On AGC Off Video Output CVBS 1 0Vp p 750 composite LENS Zoom Ratio 3 6x Manual Focus Length 2 8 10 0mm F1 2 Angular Field of View Tele 28 H x 21 V Wide 94 4 H x 69 2 V PAN TILT ROTATE Pan Tilt Rotate Range 0 352 0 73 0 348 OPERATIONAL Electronic Shutter Speed 1 60 1 120k sec 1 50 1 120k sec NTSC Korean English Japanese Spanish French Portuguese ON Screen Display PAL English Chinese German Italian French Spanish Russian Czech Polish Romanian Serbian Swedish Danish Turkish Portuguese SSDR On Off Level adjustable Backlight Compensation BLC HLC OFF 32_ specifications Day amp Night COLOR BW AUTO S W Type Gain Control Low High Off White Balance ATW Outdoor Indoor Manual AWC 1 700 K 11 000 K SNOILVOISIOAdS O SENS UP frame Integration Auto Off Selectable x2 x512 Motion Detection On Off 8 Programmable zones Privacy Masking On Off 12 Programmable zones 3D Noise Filter SSNRIII On Off Level adjustable Digital Zoom On Off x1 x16 cs onto Camera Title On Off Displayed 15 Characters Sharpness On Off Level adjustable Flip Mirror On 0 Communication Coaxial Pelco
5. D Center 701 Sampyeong dong Bundang gu Seongnam si Gyeonggi do Korea 463 400 TEL 82 70 7147 8740 60 FAX 82 31 8018 3745 SAMSUNG TECHWIN AMERICA Inc SAMSUNG TECHWIN EUROPE LTD 1480 Charles Willard St Carson CA 90746 UNITED STATES Samsung House 1000 Hillswood Drive Hillswood Business Park Tol Free 1 877 213 1222 FAX 1 310 632 2195 Chertsey Surrey UNITED KINGDOM KT16 OPS www samsungcctvusa com TEL 44 1932 45 5300 FAX 44 1932 45 5325 www samsungtechwin com www samsungsecurity com P NO Z6806153601A
6. Function Setup MAIN SETUP switch so that the arrow indicates SSNR3 1 LENS DC 5 2 EXPOSURE4 2 Select a desired mode using the Function 3 WHITE BAL ATW Setup switch 4SSDR OFF OFF Deactivates SSNR3 Noise is not 5 BACKLIGHT OFF reduced gt 6 SSNR3 0 paaa 7 DAY NIGHT AUTO ON Activates SSNR3 so that noise is reduced 3 Set the SSNR3 mode to ON and press the Function Setup switch Then you can adjust the noise reduction level SSNR3 LEVEL NEST 10 Press SET to Return N You cannot set the SSNR3 to ON or OFF when the AGC mode of the EXPOSURE menu is OFF When adjusting the noise reduction level of the SSNR3 mode remember that the higher the level set the more the noise level will be reduced but that after image may also occur DAY NIGHT You can display pictures in color or black and white 1 When the SETUP menu screen is displayed select DAY NIGHT by using the Up and MAN SETUP NS 1 LENS Down buttons so that the arrow indicates i 2 EXPOSURE DAY NIGHT 23 WHITE BAL 2 Select a desired mode using the Left and 4 SSDR Right buttons according to the picture 5 BACKLIGHT display you want 6 SSNR3 gt 7 DAY NIGHT 8 SPECIAL _ 24_ setup COLOR The picture is always displayed in color B W The picture is always displayed in black and white You can turn on or off the burst signal on B W mode AUTO The mode is switched to Color in a norm
7. MONITOR CAM TITLE SPECIAL SYNC MOTION DET PRIVACY e DIS LANGUAGE RETURN EXIT SAVE NOT SAVE RESET MENU SETUP Use the Function Setup switch within the camera Function Setup switch 1 Press the Function Setup switch Main setup menu is displayed on the monitor screen 18 setup ie em MAIN SETUP Select the function gt 1 LENS 061 Change the status using the Function EXPOSURE using the Function Setup switch WHITE BAL ATW Setup switch SSDR OFF BACKLIGHT OFF SSNR3 ON DAY NIGHT SPECIAL EXIT SAVE o C C NET dnias e 2 Select a desired function using the Function Setup switch Place the cursor over a desired item 3 Set up a selected item by using the Function Setup switch 4 To finish the setting select EXIT and press the Function Setup switch N An item with the lt icon also has sub menus To select a sub menu select an item with the icon and press the Function Setup switch Anitem with the icon is unavailable due to function settings LENS Using this function you can control the screen brightness 1 When the SETUP menu screen is displayed select LENS by using the Function Setup switch so that the arrow indicates LENS 2 The Lens mode has a sub menu shown below BRIGHTNESS Adjusts the video brightness FOCUS ADJ To adjust the lens focus correctly you must activate the Focus Settings mode To ac
8. bright fluorescent light Therefore take care when choosing the installation position When the SHUTTER is set to MANUAL or A FLK mode SENS UP will be disabled AGC AUTO GAIN CONTROL The higher the gain level the brighter the screen but the higher the noise OFF Deactivates the AGC function LOW Allows automatic gain control from 5 3dB to 32dB HIGH Allows automatic gain control from 5 3dB to 37dB SENS UP When it is night or dark the camera automatically detects the light level and maintains a clear picture if this mode is activated OFF Deactivates the SENS UP function Press SET to Retu AUTO Activates the SENS UP function bonded RETURN Select this to save the changes in the EXPOSURE menu and return to the SETUP menu N f you press the Function Setup switch in AUTO mode You can adjust brightness by adjusting the SENS UP level X2 x512 Note that the higher the SENS UP level the brighter the screen but the more likely it is that an after image will appear Although Noise Spots and Whitish symptoms may occur in SENS UP operation when the sens up level is increased this is normal f GAIN of EXPOSURE is not in use the SENS UP Sensitivity Up is set to 20 setup WHITE BAL WHITE BALANCE Use the White Balance function to adjust the screen color 1 When the SETUP menu screen is displayed select White Bal by using the Functi
9. device pursuant to part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense IC Compliance Notice This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations of ICES 003 Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local
10. govemment office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal Correct disposal of batteries in this product Applicable in the European Union and other European countries with separate battery return systems This marking on the battery manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life Where marked the chemical symbols Hg Cd or Pb indicate that the battery contains mercury cadmium or lead above the reference levels in EC Directive 2006 66 If batteries are not properly disposed of these substances can cause harm to human health or the environment To protect natural resources and to promote material reuse please separate batteries from other types of waste and recycle them through your local free battery retum system 6 safety information J O NK a important safety instructions Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth 102 UNO mE Do not block any ventilation openings Install in accordance with the manufacturer
11. panning angle to the correct viewing position by rotating the pan base Adjust the tilting angle by rotating the tilt base Loosen the rotate base hold screw and adjust rotate base for the best view O Tighten the rotate base hold screw English 15 connection CONNECTING TO MONITOR Connect the VIDEO OUT jack to the VIDEO IN jack of the monitor Monitor Asthe connecting method varies with the instruments refer to the manual supplied with the instrument f necessary you can connect the monitor to the REMOTE jack on the back of your camera Only connect the cable when the power is turned off CONNECTING TO POWER Connect the adaptor to the power input terminal as shown in the figure below The recommended adaptor specification for SCD 2080EN SCD 2080EP is DC 12V 500mA or AC 24V 300mA E Power Input Terminal When the resistance value of copper wire is at 20 C 68 F Copper wire size AWG 24 0 22mm 22 0 3 20 0 52mm 18 0 83mm Resistance A m 0 078 0 050 0 030 0 018 Voltage Drop V m 0 028 0 018 0 011 0 006 As shown in the table above voltage decreases as the wire gets longer Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera Standard voltage for camera operation DC 12V 10 There may be some deviation in voltage drop dep
12. s instructions 8 Do not install near any heat sources such as radiators heat registers or other apparatus including amplifiers that produce heat NOILVINHOHNI AL34VS O 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and athird grounding prong The wide blade or the third prong is provided for your safety If he provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus 13 Unplug this apparatus when a card is used Use caution when moving he cart apparatus combination to avoid injury from tip over 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as powersupply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids
13. Coaxitron ENVIRONMENTAL M Temperaure 450 C 3096 80 RH Storage Terperature ngega 460 C 2096 90 RH Humidity MECHANICAL Dimension Weight 0115 8 x 92 7 H mm 0 34kg X This specification can be changed without notice for performance improvement of product English 33 specifications DIMENSION 0107 6 SAMSUNG 83 7mm 939 e o Y S 81 6mm 34 specifications a m gt rm m m TH DECLARATION OF CONFORMITY Application of Council Directive s 2004 108 EC Manufacturer s Name SAMSUNG TECHWIN CO LTD Manufacturer s Address SAMSUNG TECHWIN CO LTD 42 SUNGJU DONG CHANGWON CITY KYUNGNAM KOREA 641 716 European Representative Name European Representative Address Equipment Type Environment CCTV Camera Model Name SCD 2080EP Beginning Serial NO C64A6V2Z700001Z Conformance to EN 55022 2006 EN 50130 4 2003 We the undersigned hereby declare that the equipment specified above conforms to the above Directive s Manufacturer SAMSUNG TECHWIN CO LTD Legal Representative in Europe 1 Signature FT Gu Signature Full Name BONJENG GU Full Name Position QUALITY CONTROL MANAGER Position Place CHANGWON KOREA Place MEMO MEMO MEMO MEMO SALES NETWORK SAMSUNG TECHWIN CO LTD Samsungtechwin R amp
14. T mwm 54 TOP BOTTOM LEFT RIGHT RIGHT unnm 121 Adjust the area to be enhanced Press SET to Return HLC High Light Compensation This function masks any areas of peak white HLC SETUP light this minimizes whiteout due to over LEVEL MIDDLE exposure and thus preserve much of the on LIMIT NIGHT ONLY screen details that are within the camera view MASK COLOR BLACK LEVEL Adjusts the brightness level of a MASKTONE mmn monitoring area TOP BU LIMIT Enable to change the operating Ta Pda condition RIGHT ka MASK COLOR TONE Change the color brightness of the masking area Black Red Blue Cyan Magenta TOP BOTTOM LEFT RIGHT Adjust the area to be enhanced OFF Not being used 3 Select a desired mode using the Function Setup switch and press the switch N Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen optimize the installation angle for the best HLC performance When dark the HLC is only activated when a bright light exceeding a specific size In NIGHT ONLY mode The HLC is not activated in day light or when bright light is not present at night In NIGHT ONLY mode When HLC function is used D ZOOM and DIS functions are not activated English 23 dnias e Setup SSNR3 This function reduces the background noise in a low luminance environment 1 When the SETUP menu screen is displayed select SSNR3 by using the
15. al environment but AUTO SETUP switches to B W mode when eg ws ON ambient illumination is low To set i m DURATION d up the switching time for AUTO DWELL TIME 3 SEC Tv mode press the Function Setup 3 BW COLOR switch You can turn on or off the DURATION FAST burst signal on B W mode DWELL TIME 10 SEC DURATION You can select the 4 RETURN4 I day night switching point DWELL TIME You can select the duration time about changing the day night mode 3s 55 7s 108 15s 20s 30s 40s 60s Color BW B W Color Early 2 5 lux 5 lux Late 1 lux 10 lux x The day night switching point of the camera can be adjusted N When AGC in the EXPOSURE menu is OFF AUTO mode is not available to select English 25 Setup SPECIAL 1 When the SETUP menu screen is displayed select SPECIAL by using the Function MAIN SETUP Setup switch so that the arrow indicates ee gl SPECIAL 3 WHITE BAL 4 SSDR 5 BACKLIGHT 6 SSNR3 7 DAY NIGHT gt 8 SPECIAL4 9 EXIT 2 Select a desired mode using the Function SPECIAL Setup switch gt IMAGE ADJa 1 2 MONITOR 10041 3 CAM TITLE OFF 4 SYNC INT 5 MOTION DET OFF 6 PRIVACY OFF 7 DIS OFF 8 LANGUAGE ENGLISH 9 RETURN IMAGE ADJ 1 When the SPECIAL menu screen is displayed select IMAGE ADJ by using y egy IMAGE SETUP the Function Setup switch so that the AREN arrow indicates IMAGE ADJ D Z00M 2 Select a desired mo
16. ce operation may become unstable English 21 dnias e Setup SSDR SAMSUNG SUPER DYNAMIC RANGE SSDR illuminates darker areas of an image while retaining the same light level for brighter areas to even out the overall brightness of images with high contrast between bright and dark areas 1 When the SETUP menu screen is displayed select SSDR by using the Function Setup Switch so that the arrow indicates SSDR 2 Use the Function Setup switch to change the SSDR level in the sub menu according to the contrast between bright and dark areas BACKLIGHT MAIN SETUP 1 LENS 2 EXPOSURE 3 WHITE BAL gt 4 SSDR 5 BACKLIGHT SSDR OFF The SCD 2080E is designed so that it delivers a distinctive subject and background at the same time even when the subject is in backlight by adopting a function of the proprietary W V DSP chip 1 When the SETUP menu screen is displayed select BACKLIGHT by using the Function Setup switch so that the arrow indicates BACKLIGHT MAIN SETUP 1 LENS 2 EXPOSURE 3 WHITE BAL 4 SSDR 5 BACKLIGHT 6 SSNR3 2 Select a desired mode using the Function Setup switch depending on the camera purpose 22 setup BLC Enables a user to directly select a desired area from a picture and to gt LEVEL BLC SETUP MIDDLE view the area more clearly TOP 38 LEVEL Adjusts the brightness level of a BOTTOM nn 109 monitoring area LEF
17. dark gt Adjust the contrast feature of the monitor or DVR If you have an intermediate device set the 750 Hi z properly The camera is not working gt Check that you have properly connected the camera to an appropriate properly and the surface of the power source camera is hot The SENS UP function does not Check that AGC of EXPOSURE SETUP menu is OFF work gt Check that SHUTTER of EXPOSURE SETUP menu is A FLK or The Motion Detection function does y Check that MOTION DEF of SPECIAL SETUP menu is OFF not work Color is not correct gt Check the setting of WHITE BAL SETUP menu The screen flickers continually gt Check that the camera is not pointing at the sun When coaxial communication is not available gt Make sure that the camera and moni recommended distance itor are installed within the gt Use the video amplifier equivalent to coaxitron if the recommended installation distance is exceeded English 31 specifications SPECIFICATIONS ELECTRICAL Input Voltage DC 12V AC 24V Power Consumption Max 3 5W VIDEO Imaging Device 1 3 inch Diagonal 6mm Super HAD CCD Total Pixels 811 H x 508 V 795 H x 596 V Effective Pixels 768 H x 494 V 752 H x 582 V Scanning System 2 1 Interlace Synchronization Internal Line Lock Frequency 15 734KHz V 59 94Hz H 15 625KHz V 50 00Hz Horizontal Resolution COLOR
18. de using the Function FONT COLOR Setup switch SHARPNESS V REV You can flip the picture verti RETURN cally on the screen H REV You can flip the picture horizontally on the screen D ZOOM You can use a digital zoom of x1 x16 FONT COLOR You can change the OSD font color White Yellow Green Red Blue SHARPNESS As you increase this value the picture outline becomes stronger and clearer Adjust this value appropriately depending on the sharpness of the picture RETURN Select this to save the settings for the IMAGE ADJ menu and to retum to the SPECIAL menu 26_ setup N When the V REV H REV mode is enabled the text on the screen does not flip f you increase the SHARPNESS level too high the picture may become distorted or noise may appear Monitor Please change the settings value of video appropriate to your monitor LCD Please select this menu item when using an LCD monitor LCD MONITOR You can change the gamma PED b GAMMA 035 pe PED LEVEL 17 level and color gain in the sub menus COLOR GAIN 50 CRT Please select this menu item when RESET using a CRT monitor Press SET to Return USER Please use this menu item when using a monitor other than standard ones You can change the gamma PED level and color gain in the sub menus CAMTITLE If you enter a title the title will appear on the monitor O If the SPECIAL menu screen is displayed use t
19. ending on the type of wire and the manufacturer 16 connection e N Be sure to connect power only after all the installation is complete Note that DC adaptor is not supplied with camera Ground should be connected to the GND terminal USING COAXIAL COMMUNICATIONS Coaxial Communications System 2 OSD Control method m CAMERA DVR CONTROLLER 8 SET MENU ENTER OSD KEY h UP UP KEY JOYSTICK UP DOWN DOWN KEY JOYSTICK DOWN l LEFT LEFT KEY JOYSTICK LEFT RIGHT RIGHT KEY JOYSTICK RIGHT e e RS 485 Video Cable The camera s video output port is connected to the monitor with a BNC coaxial cable shown below If the distance between the camera and the monitor exceeds the recommended maximum please use an auxiliary video amp e _ Distance Recommended Cable Specification 1 300m 3C2V RG 59 U 450m 5C2V RG 6 U e y 600m 7C2VRG 11 U N If the camera is controlled through coaxial communication please use a video amp intended for coaxial communications Regular video amps do not transfer coaxial signals English 17 Setup MENU CONFIGRATION MAIN SETUP LENS DC BRIGHTNESS SHUTTER AGC EXPOSURE SENS UP RETURN ATW OUTDOOR INDOOR WHITE BAL MANUAL AWC SET SSDR 0FF 0N BACKLIGHT BLC HLC SSNR3 ON OFF DAY NIGHT AUTO COLOR e BW O IMAGE ADJ
20. he Function Setup switch so hat the arrow indicates CAM TITLE Set it to ON by using the Function CAMERA TITLE SETUP Setup switch ABCDEFGHIJKLM Press the Function Setup switch N A P a R T n TET 2 I m Q Use the Function Setup switch to nopars uv 2 xyz move to a desired letter and select the 0123456789 letter by pressing the switch Repeat gt CLR POS END his to enter multiple letters You can enter up to 15 letters Q Enter a title move the cursor to POS and press the Function Setup Switch The entered title appears on the screen Select the position to display the itle on the screen by using the Function Setup switch and press When the position is determined select END and press he Function Setup switch to return to the SPECIAL menu English 27 dnias e Setup When the CAM TITLE menu is OFF no title will be displayed on the monitor screen even if you enter one English and Numbers are available in the mode Ifyou move the cursor to CLR and press the Function Setup switch all the letters are deleted To edit a letter change the cursor to the bottom left arrow and press the Function Setup switch Move the cursor over the letter to be edited move the cursor to the letter to be inserted and then press the Function Setup switch SYNC In areas where the supply is at 60Hz NTSC 50Hz PAL you can synchronize the output phase of multiple came
21. ime Before operating the camera confirm the camera model and correct input power voltage To help you understand this manual thoroughly we ll introduce our model description W SCD 2080E SERIES NTSC MODEL PAL MODEL SCD 2080EN SCD 2080EP W MODEL DESCRIPTION SCD 2080EX SIGNAL SYSTEM SIGNAL SYSTEM N NTSC MODEL P PAL MODEL safety information AN CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING To prevent damage which may result in fire or electric shock hazard do not expose this appliance to rain or moisture To prevent injury this apparatus must be securely attached to the floor wall in accordance with the installation instructions WARNING 1 Be sure to use only the standard adapter that is specified in the specification sheet Using any other adapter could cause fire electrical shock or damage to the product 2 Incorrectly connecting the power supply or replacing battery may cause explosion fire electric shock
22. on MAIN SETUP Setup switch so that the arrow indicates 1 LENS DC 1 White Bal 2 EXPOSURE _ b 3 WHITE BAL ATW 2 Select a desired mode using the Function 4 SSDR OFF Setup switch x Select one of the following 5 modes as appropriate for your purpose ATW Select his when the color temperature is between 1 700 K and 11 000 K OUTDOOR Select this when the color temperature is between 1 700 K and 1 000 K sodium light inclusion Select this when the color temperature of environment surrounding the subject is out of the control range e g clear sky or sunset INDOOR Select this when the color temperature is between 4 500 K and 8 500 K MANUAL Select this to fine tune White Balance manually Set White WB MANUAL Balance first by using the ATW gt RGAIN 529 or AWC mode After that switch BGAIN nummum 532 to MANUAL mode fine tune the White Balance and then press Press SET to Return the Function Setup switch AWC SET To find the optimal luminance level for the current environment point the camera towards a sheet of white paper and press the Function Setup switch If the environment changes readjust it N White Balance may not work properly under the following conditions When the ambient illumination of the subject is dim if the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically the White Balan
23. onotonic as like sky or white wall f DIS is enabled the digital zoom is not configured to less than 46 level English 29 Setup LANGUAGE You can select the menu language according to your requirements RETURN Select this to save the SPECIAL menu settings and return to the MAIN SETUP menu EXIT Select a desired EXIT mode using the Function Setup switch depending on the camera purpose SAVE Save the current settings and exit the MAIN SETUP menu NOT SAVE Do not save the current settings and exit the MAIN SETUP menu RESET Resets the camera settings to the factory defaults Language and Monitor settings are not initialized 30 setup troubleshooting TROUBLESHOOTING If you have trouble operating your camera refer to the following table If the guidelines do not enable you to solve the problem contact an authorized technician PROBLEM SOLUTION e x Nothing appears on the screen Check that the power cord and line connection between the camera 3 and monitor are fixed properly gt Check that you have property connected VIDEO cable to the camera n VIDEO output jack ES s The image on the screen is dim gt Is the lens stained with dirt Clean your lens with a soft clean cloth 3 5 Check the monitor and DVR settings If the camera is exposed to very strong light change the camera position The image on the screen is
24. or damage to the product 3 Do not connect multiple cameras to a single adapter Exceeding the capacity may cause abnormal heat generation or fire 4 Securely plug the power cord into the power receptacle insecure connection may cause fire 5 When installing the camera fasten it securely and firmly The fall of camera may cause personal injury 4 safety information Do not place conductive objects e g screwdrivers coins metal parts etc or containers filled with water on top of the camera doing so may cause personal injury due to fire electric shock or falling objects Do not install the unit in humid dusty or sooty locations doing so may cause fire or electric shock If any unusual smells or smoke come from the unit stop using the product in such case immediately disconnect the power source and contact the service center continued use in such a condition may cause fire or electric shock If this product fails to operate normally contact the nearest service center never disassemble or modify this product in any way samsung is not liable for problems caused by unauthorized modifications or attempted repair 10 When cleaning do not spray water directly onto parts of the product doing so may cause fire or electric shock CAUTION 1 Do not drop objects on the product or apply strong shock to it Keep away from a location subject to excessive vibrationor magnetic interference
25. ras using the power Press SET to Return synchronization function Line Lock without using a synchronization signal generator INT Internal Synchronization Type L L Power Synchronization Type Line lock Press the Function Setup switch You can select a desired phase from 0 to 359 when select phase SYNC gt PHASE mmm 0 N When using AC power at 60Hz NTSC 50Hz PAL frequency you can use the L L type synchronization When the power is DC 12V the SYNC menu is fixed to the INT mode e MOTION DET MOTION DET This product has a feature that allows gt 1 SENSITIVITY AREA you to observe movement of objects in 2 AREA MODE ON 8 different areas on the screen and the 3 SEL POS L TOP words MOTION DETECTED appear on 4 05 mmm the screen when movement is detected 5 5 senum 4 You can monitor activity more efficient GALL SET 7 RETURN When the SPECIAL menu screen is displayed press the Function Setup switch so that the arrow indicates MOTION DET Set up the mode using the Function Setup switch SENSITIVITY You can select up to 8 MD areas When SENSITIVITY number is high motion detection sensitivity is increased to recognize even small movement 28 setup AREA MODE Determines whether to use the MD area selected in SENSITIVITY SEL POS Determines which of the 4 vertices of each MD area is to be used XPOS Determines the coordinate of the ho
26. rizontal axis for SEL POS YPOS Determines the coordinate of the vertical axis for SEL POS FILL SET Fills in a selected MD area The color of filling is sequentially selected as brown orange blue cyan yellowish green yellow magenta and red RETURN Select this to save the MOTION DET menu settings and return to the SPECIAL menu dnias e PRIVACY Mask an area you want to hide on the screen When the SPECIAL menu screen is displayed press the Function Setup switch pi m oid AREA SETUP so that the arrow indicates PRIVACY 2 MODE OFF Set up the mode using the Function 3 MASK COLOR GREEN Setup switch 4 MASK TONE um 1 AREA You can select up to 12 5 TOP LEST 39 PRIVACY areas 6 BOTTOM ST 79 MODE Determines whether to use UE geo E the area selected 9 RETURN4 MASK COLOR Determine area color You can select GREEN RED BLUE BLACK WHITE and GRAY MASK TONE Adjust the brightness of MASK COLOR TOP BOTTOM LEFT RIGHT Adjust the size and position of the selected area RETURN Select this to save the PRIVACY menu settings and return to the SPECIAL menu DIS Digital Image Stabilizer This function mitigates any picture movement due to external factors such as wind Asthe DIS function uses the digital zoom the camera s resolution will decrease DIS doesn t operate when background illumination is too low DIS doesn t operate when object pattern is m
27. switch Display the menu on the screen and move the cursor to four directions to confirm status or after changing a selected item Video Output Jack Power Input Terminal Dome Cover Shield Case English_11 installation INSTALLATION 1 Separate the dome cover by turning anti clockwise 2 Separate the shield case by pulling from the camera body To install the dome cover on the camera body turn the latches in locking direction as atch shown in the Figure 1 Shield Case Unlocking direction Locking direction Anti clockwise Clockwise Dome cover Original position of the cable N The installation should be done by qualified service personnel or system installers fthe ceiling material is not strong enough to hold the installation screws the camera may fall off Reinforce the ceiling as needed Hole Cover To change the position of the cable take away the Hole Cover and pass the cable through 12 installation WHEN USING THE CEILING BRACKET Ceiling bracket An arrow for installing directions NOILVTIVISNI O M4 tapping screw provided Dome cover 1 Hold the ceiling bracket located where the arrow points to and separate it from the main body of the camera by rotating it anti clockwise refer to the picture in Notes on page 13 2 Place the separated ceiling bracket so that the Front side faces the area to be monitored and install it with
28. the M4 tapping screws 3 To combine the main body with the ceiling bracket make sure that the Pan Base fixing screw face the opposite side of the Front side of the ceiling bracket and rotate it clockwise 4 Adjust the camera lens to face the area to be monitored and fix the main body and the dome cover by aligning the grooves and rotating the body clockwise English 13 installation M4 tapping Screw Figure 2 N Ifyou want to install the camera with the ceiling bracket together fix them using two tapping screws at the side of the main body refer to the Figure 2 on page 14 14 installation le ADJUST THE PANNING AND TILTING WHILE WATCHING THE MONITOR NOILVTIVISNI O Pan Base 1 You can adjust camera to any direction by using Pan Tilt Rotate mechanism Pan Base moves by 176 to each side direction and 352 on the whole e Tilt Base covers total 73 angle 0 73 Change to read Rotate Base moves by 174 to each side direction and 348 in total 2 Methods of adjustment Installing the dome on a wall After mounting the camera on a wall adjust the panning angle so that the camera faces the direction that is to be monitored Adjust the tilting angle by rotating the tilt base Loosen the rotate base hold screw and adjust rotate base for the best view O Tighten the rotate base hold screw Installing the dome on a ceiling After mounting the camera on a ceiling adjusting the
29. tivate the Focus Settings mode adjust the lens focus and then deactivate the settings mode You can adjust the shutter value of ESC shutter mode MAIN SETUP gt 1 LENS DC 2 EXPOSURE N f color rolling occurs set Shutter to EXPOSURE 1 When the SETUP menu screen is displayed select EXPOSURE by using the Function Setup switch so that the arrow indicates EXPOSURE 2 Select a desired mode using the Function Setup switch MAIN SETUP 1 LENS Dea D gt 2 EXPOSURE lt _ 3 WHITE BAL ATW English 19 Setup BRIGHTNESS Adjusts the video brightness EXPOSURE SETUP SHUTTER You can select the shutter gt 1 BRIGHTNESS 25 A FLK Select this when you 2 SHUTTER experience picture flicker which can 3 AGC HIGH 4 SENS UP OFF 5 RETURNe_ happen when there is a clash with the frequency of the installed lighting ESC Select this to control the shutter speed automatically If ESC is selected the shutter speed is automatically controlled depending on the ambient illumination of the subject MANUAL You can control shutter speed manually NTSC MODEL 1 60 1 120 000 sec PAL MODEL 1 50 1 120 000 sec Shutter speed is fixed at 1 60sec 1 50sec A Setthe shutter mode to if color rolling occurs When the SHUTTER is set to ESC after selecting the Internal Synchronization Type the picture may become unstable if the camera faces a
30. ynamic Range For images with high contrast between bright and dark areas from difficult lighting conditions such as backlighting this camera selectively illuminates darker areas while retaining the sare light level for brighter areas to even out the overall brightness DIS Digital Image Stabilizer The DIS function compensates for any camera movement to produce more stable pictures Communication Coaxial communication methods are supported Protocol Pelco Coaxitron Miscellaneous Functions HLC High Light Compensation SENS UP FLIP H V REV D ZOOM SHARPNESS and PRIVACY functions are provided OSD The camera control is convenient by using 17 different foreign language O S D NTSC English Japanese Spanish French Portuguese Korean PAL English French German Spanish Italian Chinese Russian Polish Czech Romanian Serbian Swedish Danish Turkish Portuguese English 9 introduction WHAT S INCLUDED Check if the following items are included in the product package SCD 2080E User Manual Quick Set up Guide v we Installation Video M4 Tapping Screw 3EA Output Cable 10 introduction COMPONENT NAMES AND FUNCTIONS FRONT NOLLONGOHINI Pan Base Control panning angle of camera Rotate Base Control rotating angle of camera x3 6 Vari focal Lens Module 2 8 10 0mm F1 2 Video Output Terminal to Monitor Function Setup
Download Pdf Manuals
Related Search