Saeco Royal Super-automatic espresso machine HD8930/02
Contents
1. sccccccssssssssscsecssssssssserseceeee 14 Adjustments Adjusting the Coffee Grinder Adjusting the Aroma Amount of Ground Coffee Adjusting the Coffee Length Adjusting the Cappuccino or Latte Macchiato Length Eco friendly Stand by Brewing Coffee nescire tecoe secet va ebvsetesseses sense sesseareese 19 Cup warming Surface Adjusting the Dispensing Spou Using Coffee Beans Using Pre ground Coffee Brewing Cappuccino eeeeeee eese ee ees esses esee sseesssees 23 Latte Macchiato e c ee eese ee eee ee eese eee eeeeeseseeessees 24 Milk Handling eere eese eene eene ee eee seen eeeseees 25 Milk Thermos Milk Container SPECIAL Produ cts eere eres eto se veo riso sevsoereseseosicsesper 2O Dispensing Hot Water Long Coffee Hot Milk American Coffee Beverage Programming Dispensed Beverages Counters Beverage Parameters Hot Water Parameters BEVERAGE MENU SPECIAL BEVERAGES Default Parameters Machine Programming eee ee eee eere eene eeneeeneees 33 General Menu Display Menu Water Menu Maintenance Factory e EE 36 Cleaning and Maintenance General Cleaning Cleaning the Cappuccinatore After Each Use 38 Day Cleaning Thermos Monthly Cleaning Cappuccinatore Thermos Thorough Cleaning 43 Brew Group ccccssssc2. The lack of cleaning before and after each use can affect the correct opera tion of the machine Danger of burning Dispensing may be preceded by small jets of hot water For a quick cleaning proceed as follows BER Make sure the Cappuccinatore complete with all its parts is correctly inserted Insert the suction hose in a carafe containing clean water EJ Place a container under the dispensing spout ER With the machine on press the CA button SE CAPPUCCINATORE CLEAN Ell Press the Sy button to start the cleaning cycle for the Cappuccinato OK REPLACE MILK CONTAINER re WITH ANOTHER ONE WITH FRESH WATER s P Note To exit the cycle at any moment press the button ESC CAPPUCCINATORE CLEAN PLEASE WAIT ESC ENGLISH 39 al The machine warms the system up Once the warm up is complete the machine performs an assisted wash cycle for the Cappuccinatore Wait until the cycle is complete Only once the cycle is complete press the side buttons and remove the Cappuccinatore EJ Place the cover back on the machine Important Note We recommend removing the Cappuccinatore when not be ing used in order to keep it clean EJ Remove the suction tube from the Cappuccinatore RY Remove the ring from the Cappuccinatore 40 ENGLISH KE Rotate and lift the Cappuccinatore cover and remove it from the Cap puccinatore body Remove the valve
3. This section allows you to program the amount of milk for each selected beverage The bar allows you to adjust the exact amount of milk to be dispensed LO button A to increase the amount of milk in the cup So button V to reduce the amount of milk in the cup ENGLISH 33 Hot Water Parameters BEVERAGE MENU gt SPECIAL BEVERAGES HOT WATER These settings are valid only for programming hot water dispensing WATER QUANTITY DEFAULT This section allows programming the amount of water to be dispensed WATER QUANTITY when pressing the corresponding button The bar allows you to adjust the exact amount of water to be dispensed LO button A to increase the amount of hot water in the cup e button W to reduce the amount of hot water in the cup Default Parameters For each beverage it is possible to reset the original standard values as DEFAULT signed by the manufacturer After selecting this function the beverage customized settings are deleted Machine Programming The machine allows you to customize the operating settings LNA CUN gt Kl Press and hold the button for 5 seconds to access the machine ze main menu When you enter the programming mode the buttons have a different PHILIPS function e Saeco gy button OK confirms a selection or a change you have made MENU Ai nu BEVERAGE MENU button A scro
4. CLOSE SIDE DOOR INSERT DRIP TRAY INSERT COFFEE GROUNDS DRAWER CLOSE HOPPER DOOR REFILL WATER TANK INSERT BREW GROUP INSERT CAPPUCCINATORE INSERT VALVE INTO CAPPUCCINATORE ADD COFFEE ENGLISH 55 LCD Display Warnings Help Message Displayed How to Reset the Message To restore the machine operation close the service door Insert the drip tray Insert the coffee grounds drawer Close or correctly place the coffee bean hopper inner lid to be able to prepare any product Remove the tank and fill it with fresh drinking water Insert the Brew Group into its seat An operation has been selected that requires dispensing milk Insert the Cappuccinatore in the machine as specified in the manual The selected operation requires milk dispensing Insert the previ ously removed valve in the Cappuccinatore as described in the manual see step 10 on page 39 Fill the coffee bean hopper with coffee beans 56 ENGLISH Help Message Displayed How to Reset the Message MA anam f Chic QRovar S SN CT gt OVAL Rov by EMPTY COFFEE GROUNDS DRAWER li 9960 RESTART TO SOLVE a DESCALING DESCALING NEEDED DESC
5. GROUP CLEANING ESC BREW GROUP CLEAN REFILL WATER TANK Besides weekly cleaning we recommend running the cleaning cycle with Coffee Clean Tablets after approximately 500 cups of coffee or once a month This operation completes the maintenance process of the brew group The Coffee Clean Tablets to clean the Brew Group and the Maintenance Kit may be purchased at your local dealer at the Philips on line shop at http shop philips com or at authorised service centres Warning The Coffee Clean Tablets has no descaling property For descal ing use the Saeco descaling solution and follow the procedure described in the Descaling chapter The wash cycle cannot be stopped Do not leave the machine unattended during this operation Warning Drinking the solution dispensed during this procedure is strictly forbidden The solution must be disposed of Kl Press and hold the amp 2 button for 5 seconds to enter the machine main menu Press the amp button and the button to confirm the selection and enter the MACHINE MENU EJ Press the button and select the MAINTENANCE option press the NS button to enter the menu ER Press the iC button to confirm H Press the amp button to start the cleaning cycle of the brew group Note If this option is confirmed the cycle must be completed Press the ECK button to exit ES Fill the water tank and press the amp button to confir
6. Use At first start up the machine requires you to select and store the desired language for the displayed messages This allows you to adjust the pa rameters of the beverages to the typical parameters of the country where the machine is used This is why some languages are differentiated also by country If no language is selected you will be requested to select it at next ma chine start up BER Select the language by pressing the O or e button Press the ei button to store the language Warm up and Rinsin Kl Upon start up the machine activates the warm up phase Wait until it is completed Note The bar is in progress to show that the machine is heating up the system Once the warm up is complete the machine performs a rinse cycle of the internal circuits Note The bar is in progress to show that the machine is performing the system rinse cycle A small quantity of water is dispensed Wait for the cycle to end Note The cycle can be stopped by pressing the button EJ Then the machine is ready for use The logo oer is displayed indicating that the machine is ready for use Note If the machine is being used for the first time or after a long period of inactivity follow the procedures described in the following section 10 ENGLISH Rinse Self Cleaning Cycle This cycle allows you to rinse the internal coffee circuits with fresh water The cycle is carried out At machine start up with cold bo
7. after its installation or replacement Refer to the relevant section on page 14 to correctly install and or replace the filter 36 ENGLISH Maintenance This menu allows setting all the functions for correct machine mainte MAINTENANCE nance BREW GROUP CLEAN This function allows you to perform the wash cycle for the Brew Group see page 48 This function allows you to perform the descaling cycle see DESCALING page 51 This function allows you to perform the wash cycle for the Cappuccinatore and or Thermos used to prepare the milk based beverages see page 43 CAPPUCCINATORE CLEAN Note This cleaning procedure is fundamental for correct maintenance and operation of the Cappuccinatore and or Thermos Factory Settings This function allows restoring all factory settings FACTORY SETTINGS Note This section allows you to restore the factory settings relative to the machine menu personal settings ENGLISH 37 Cleaning and Maintenance As some of the parts of your appliance come in contact with water and cof fee during normal use it is important that you clean your appliance regu larly This is an easy procedure with your Philips Saeco Espresso machine Just follow the steps indicated on the display and described below Not doing this will ultimately make your appliance stop working properly and in this case repair is not covered under your warranty General Cleanin BR Empty and clean the drip tr
8. and with maximum convenience CONSUMER RELATIONS DESKS For Downloads amp FAQs visit our Customer Support Website www philips com support Argentina 0800 888 7532 numero gratuito Australia 1300 363 391 option 3 toll free Bahrain 973 17700424 Baltics Estonia 8000100288 tasuta Latvia 6616 3264 pa vald bu l menis eg Lithuania 852140294 vietinis tarifas Belgium 070 700 036 0 15 p min Brazil 0800 701 0203 Demais localidades TN RUNE 11 2121 0203 Grande Sao Paulo Bulgaria 359 02 4916274 nauwonannn rapua Canada 1 800 371 7597 local toll free 228880896 vnitrost tn sazby 4008 800 008 385 01 777 66 02 35 44 41 30 lokal takst 0800 000 7520 f r Anrufe aus dem deutschen Festnetz kostenfrei 0180 501 06 71 f r Anrufe aus dem deutschen Mobilfunknetz kostenpflichtig max 0 42 Min 902881082 0 10 establecimiento de llamada 0 08 min 0157324051 tarif national 2111983029 Denmark Germany Hong Kong 852 2619 9663 Israel 03 6458844 Iran 98 21 2227 9353 Ireland 08 18 2101 41 National call Italy 02 45279074 tariffa nazionale Japan 813 3 3555 0156 Korea 080 600 6600 toll free Kuwait 1803535 Lebanon 961 1684900 Luxembourg 24871095 tarif national nationaler Tarif Magyarorsz g 061 700 8152
9. control to off then remove plug from wall outlet 12 Do not use appliance for other than intended use 13 WARNING Do not remove the cappuccinatore while in use steam can 14 Save these instructions be released CAUTION This appliance is for household use only Any servicing other than cleaning and user maintenance should be performed by an authorized service center Do not immerse machine in water To reduce the risk of fire or electric shock do not disassemble the machine There are no parts inside the machine serviceable by the user Repair should be done by authorized service personnel only 1 Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage Never use warm or hot water to fill the water tank Use cold water only Keep your hands and the cord away from hot parts of the appliance during operation Never clean with scrubbing powders or harsh cleaners Simply use a soft cloth dampened with water For optimal taste of your coffee use purified or bottled water Periodic descaling is still recommended every 2 3 months Do not use caramelized or flavored coffee beans INSTRUCTIONS FOR THE POWER SUPPLY CORD A short power supply cord or detachable power supply cord is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord Longer detachable power supply cords or extension cords are available
10. cover Power button Power cord socket Pre ground coffee dosing unit Grease for brew group Power cord Cleaning brush Milk circuit detergent Water hardness test Milk Thermos Descaling solution INTENZA Filter Brew group cleaning tablets Coffee Clean Tablets Suction tube for Cappuccinatore Connection hose Thermos Cappuccinatore Pre ground coffee selection button 2nd Function Menu button to access the programming mode Espresso coffee brew button Coffee brew button 2nd Function OK button to confirm selection Special beverages selection button 2nd Function ESC button to exit or stop the brewing procedure Display Cappuccinatore Clean button 2nd Function Page Up button to scroll the menu Cappuccino brew button 2nd Function Page Down button to scroll the menu Latte Macchiato brew button ON OFF button 4 ENGLISH Read this user manual carefully before using the appliance and save it for future reference Never allow water to come into contact with any of the electrical parts of the machine Danger of short circuit Hot water may cause burning Never not direct the hot water jet towards body parts Handle the hot water wand with care Intended Use The coffee machine is intended for domestic use only Do not make any technical changes or use the machine for unauthorised purposes since this would create serious hazards The appliance is not to be used by persons including children
11. dimensions of the cups that you wish to use Manually move the dispensing spout up or down to adjust its height 20 ENGLISH The recommended positions are For the use of small cups For the use of large cups Two cups can be placed under the dispensing spout to brew two cups of coffee at the same time If you want to use tall glasses or mugs push the dispensing spout to its limit stop In this case you can just brew one product at a time Note Before any brewing procedure and or when bringing the dispensing spout back to its normal brewing position make sure that it is correctly posi tioned This can be noted through the CLICK indicating the correct position Ifthis is not done some product might leak out of the dispensing spout ENGLISH 21 Using Coffee Beans To brew coffee press and release El The button for a cup of espresso JO T the e button for a cup of long espresso PHILIPS 2Saeco The brewing cycle then starts To brew 1 cup of coffee press the desired button once To brew 2 cups of coffee press the desired button twice consecutively Note To brew 2 cups of coffee the machine automatically grinds and doses the correct amount of coffee Brewing two coffees requires two grinding cycles and two brewing cycles which the machine carries out automatically Once the prebrewing cycle is complete coffee begins to come out of the dispensing spout EJ Coffee brewing stops automa
12. from the Cappuccinatore EE Remove the suction tube joint from the Cappuccinatore EE Wash the parts under running water Make sure any possible milk deposits residues are removed After washing reassemble the parts following the same procedure used for disassembly but in reverse order ENGLISH 41 Day Cleaning Thermos The Thermos has to be cleaned every day to ensure proper operation Note To clean the Thermos the Cappuccinatore has to be installed You can take the occasion to perform the daily cleaning of the Cappuccinatore at the same time BER Rotate the lid and open the Thermos Remove the steel tube installed inside the Thermos lid Wash it under lukewarm running water EJ Wash the Thermos lid keeping the external rubber hose with plastic fit ting inserted in particular wash the internal seal of the lid thoroughly After washing the Thermos lid install the previously removed steel tube inside it Without this tube milk cannot be frothed ER Wash the inside of the Thermos under lukewarm running water Make sure any possible milk deposits residues are removed IE Fill the Thermos with fresh water and close the lid 42 ENGLISH REPLACE MILK CONTAINER WITH ANOTHER ONE WITH FRESH WATER ESC CAPPUCCINATORE CLEAN PLEASE WAIT ESC Fal Connect the Thermos to the Cappuccinatore Place a container under the dispensing spout EJ Wi
13. hopper lid Note The hopper may be provided with different safety features according to the regulations applicable in the country of use of the machine Slowly pour the coffee beans into the hopper If the water tank is not inserted check that no coffee beans fall into the tank compartment If this happens remove them to avoid any malfunctions Only coffee beans must be put into the coffee bean hopper Ground coffee instant coffee or any other object may damage the machine EJ Reposition the coffee bean hopper lid ER Insert the plug into the socket on the back of the machine E Insert the plug of the other end of the cable into a wall socket with suitable power voltage Eli Switch the power button to I to turn on the machine Note The power button is located in the rear part of the machine After carrying out a check cycle the machine goes into stand by mode and the button blinks To turn on the machine simply press the VO button Note The language needs to be selected only upon first use see page 9 Note Once the warm up is complete upon first use the machine primes the circuit and performs a rinse cycle of the internal circuits A small amount of water is dispensed Wait for this cycle to be completed 8 ENGLISH GG 5p MENU ok PHILIPS e Saeco MENU g oK PHILIPS Saeco Z co Z R One Toi Q One Tou Double Function Buttons Some buttons
14. the drip tray and the coffee grounds drawer Open the service door 1 Rotate the lever clockwise by 90 2 Pull the door towards you EJ Remove the brew group Pull it by the handle and press the PRESS button The brew group must be washed only with lukewarm water with no detergent ES Wash the brew group with lukewarm water and carefully wash the upper filter Before placing the Brew Group in its housing make sure there is no water left in the brewing chamber E Lift the rear part of the inner tray and unlock it al Remove the inner tray wash and reposition it in its seat Mu Note When inserting the tray follow the same procedure used for disassembly but in reverse order ENGLISH 47 Make sure the Brew Group is in the rest position the two reference signs must match If they do no match proceed as described in step 8 EJ Make sure that the lever is in contact with the brew group base ER Make sure that the hook to lock the Brew Group is in the correct posi tion to check its position firmly press the PRESS button E Insert the Brew Group in its seat again until it locks into place WITHOUT pressing the PRESS button ER Insert the coffee grounds drawer and the drip tray Close the service door 48 ENGLISH Brew Group Cleaning with Coffee Clean Tablets Coffee Clean BREW GROUP CLEAN DESCALING CAPPUCCINATORE CLEANING BREW GROUP CLEAN PERFORM BREW
15. to reset all the counters of the products that have been HOT MILK dispensed until that moment This can be useful to reset the machine after COUNTERS RESET maintenance BEVERAGE MENU ESPRESSO COFFEE CAPPUCCINO LATTE MACCHIATO CAPPUCCINO PREBREWING COFFEE TEMPERATURE COFFEE LENGTH MILK QUANTITY PREBREWING COFFEE TEMPERATURE COFFEE LENGTH MILK QUANTITY Beverage Parameters In this case we look at how to programme a customized cappuccino The milk managing options are not shown when a coffee brewing espresso or long coffee is being programmed Press the amp button to select the CAPPUCCINO and the amp button Y OK to enter the menu The following describes the different functions Prebrewing Coffee is slightly dampened before brewing so as to bring out its full aroma and let it acquire an excellent taste OFF prebrewing is not performed LOW activated HIGH longer in order to bring out the coffee taste This section allows you to program the temperature for coffee brewing LOW low temperature NORMAL standard temperature HIGH high temperature This section allows programming the amount of coffee to be brewed for each selected beverage The bar allows you to adjust the exact amount of coffee to be brewed LO button A to increase the amount of coffee in the cup y button W to reduce the amount of coffee in the cup
16. way all parts will be perfectly clean and free of any milk residue BR Remove the cover from the front side Note The cover can be placed on the machine side using the integrated magnet Insert the Cappuccinatore into its seat until it locks into place Check that it cannot slide away Warning Before using the Cappuccinatore clean it along with the Thermos if used as described in the Cleaning and Maintenance section EJ Insert the clean hose according to your choice inthe milk Thermos or directly in the milk container Note To ensure better results when preparing a cappuccino use cold milk ER Place the cup under the dispensing spout Press the e button 24 ENGLISH CAPPUCCINO eu 3 gt STOP MILK CAPPUCCINO Gr wm gt STOP COFFEE E The machine needs a preheating time ES After preheating the machine starts brewing the cappuccino At this stage the EE frothed milk You can stop dis pensing by pressing the 7 button ESC EJ After dispensing milk the machine brews coffee You can stop brewing by pressing thew button ES You can enjoy your cappuccino just like at the coffee bar After using the Cappuccinatore clean it as described in the Cleaning the Cappuccinatore section Remove the container or Thermos and clean it if necessary Latte Macchiato The machine allows brewing a latte macchiato quickly and easily with the touch of a button
17. with reduced physical mental or sensory abilities or with scarce experience and or expertise unless they are supervised by a person responsible for their safety or they are instructed by this person on how to properly use the machine Power Supply Power Cord Connect the coffee machine only to a suitable socket The socket to which the machine is connected must be Compatible with the type of plug installed on the machine Suitably sized to comply with the data on the plate attached to the appliance Connected to an efficient earthing system Never use the coffee machine if the power cord is defective or damaged If the power cord is damaged it must be replaced by the manufacturer or by its authorised service centre Do not pass the power cord around corners over sharp edges or over hot objects and keep it away from oil Do not use the power cord to carry or pull the coffee machine Do not pull out the plug by the power cord or touch it with wet hands Do not let the power cord hang freely from tables or shelves For the Safety of Others Prevent children from playing with the machine Children are not aware of the risks related to electrical household appliances Do not leave the machine packaging materials within the reach of children Danger of Burns Never direct the jet of hot steam and or hot water towards yourself or oth ers Danger of burns Machine Location Suitable Location for Operation and Mainte nan
18. AA ddovar ENGLISH 11 ER Press the e button to select coffee Note Do not add pre ground coffee into the compartment Ell Press the button to start the dispensing procedure The machine will dispense hot water through the dispensing spout Wait until the dispensing procedure is complete and empty the water tank KA Repeat the operations from step 1 to step 5 for 3 times then continue with step 7 Place a container under the hot water wand EJ Press the and the buttons select and start dispensing HOT WATER ER when the hot water dispensing procedure is complete empty the container ET The machine is now ready for use 12 ENGLISH Intenza Aroma System 2 Machine water hardness setting MENU BEVERAGE MENU MACHINE MENU MACHINE MENU GENERAL MENU DISPLAY MENU WATER MENU MAINTENANCE MACHINE MENU GENERAL MENU DISPLAY MENU WATER MENU MAINTENANCE Measuring and Adjusting Water Hardness Measuring water hardness is very important in order to correctly manage the INTENZA filter and the frequency with which the machine must be descaled BR Immerse the water hardness test strip provided with the machine in water for 1 second Note The test strip is only valid for one measurement E Check how many squares change colour and refer to the table Note The letters correspond to the references t
19. ALE ESC The machine requests a descaling cycle When this message is displayed it is still possible to use the ma chine but its correct operation might be affected Damages caused by failure to descale the machine are not cov ered by warranty The machine requests the Intenza water filter to be replaced with a new one Replace the filter as described on page 14 The alarm is displayed only if the Enable Filter function is set to ON see page 35 The machine reminds that after a few cycles it will be necessary to empty the coffee grounds drawer This message does not prevent the machine from brewing some more products Remove the coffee grounds drawer and empty the coffee grounds into a suitable container Note The coffee grounds drawer must be emptied only when the machine asks for it and with the machine turned on If you empty the drawer with the machine turned off it will not record the emptying operation Blinking red light Machine in Stand by The Stand by settings can be changed see page 34 Press the ly button An event has occurred which needs the machine to be restarted Take note of the code E xx shown at the bottom Turn off the machine wait for 30 seconds and then turn it on again If the problem persists contact the service centre If this page is displayed after starting the machine this means that the descaling cycle is needed Press the button to enter the de
20. ILTER FILL THE TANK E PLACE A CONTAINER UNDER THE WATER SPOUT ACTIVATE FILTER ENGLISH 15 ES Place a large container under the hot water wand Hold the e button pressed for 5 seconds to access the program ming mode E To select the MACHINE MENU option press the E button Press the e button for access EJ Press the e button until the WATER MENU option can be selected Press the e button for access UK Kid Press the e button until the ACTIVATE FILTER option can be se lected Press the i button for access OK i Press the button Note To quit the procedure press the E button until the Rorri logo is displayed Press the iC button to confirm the introduction of the new filter Press the button to confirm Wait until the machine stops dispensing the necessary water to activate the filter At the end of the cycle remove the container that you had previously placed under the hot water wand Note At the end of the procedure the display automatically returns to the product brewing page If the water filter is not available insert the small white filter previously removed see step 1 into the tank 16 ENGLISH The machine that you have bought allows for certain adjustments that will permit you to use it to its full potential Adjusting the Coffee Grinder Warning The grind adjustment lever must only be turned when the coffee grinder is workin
21. ON OFF button Wait for the machine to finish its rinse and warm up process Warning Remove the Intenza filter before adding the descaling solution Press and hold the button for 5 seconds to access the machine main menu EJ Press the So button and the Y button to confirm the selection and enter the MACHINE MENU Wl Press the amp button and select the MAINTENANCE option press the button to enter the menu Ell Press the button and select the DESCALING option press the e button to enter the menu 52 ENGLISH DESCALING START DESCALING ESC DESCALING FILL TANK WITH DESCALING SOLUTION EMPTY DRIP TRAY DESCALING INSERT THE CAPPUCCINATORE WITH ALL THE COMPONENTS DESCALING KA Press the EI button to start the DESCALING cycle Note If this option is confirmed the rest of the cycle must be completed Press the gy button to exit Pour the entire content of the Saeco concentrated descaling solution into the water tank and then fill the tank with fresh drinking water up ERES ka to the level indicated by the Ee icon Place the tank back in the machine Press the e button UK EJ Remove any liquids from the drip tray and insert it back into the ma chine Press the ei button UK EJ Insert the complete Cappuccinatore into the machine and remove the dispensing spout Press the eg button OK Note Keep th
22. PHILIPS The manufacturer reserves the right to make changes without prior notice www philips com saeco Rev 04 del 15 03 12 15002770
23. Register your product and get support at www philips com welcome vi rar Type HD8930 OPERATING INSTRUCTIONS ma i READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THE MACHINE PHILIPS CE Saeco IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed including the following 1 2 3 8 9 Read all instructions Do not touch hot surfaces Use handles or knobs To protect against fire electric shock and injury to persons do not immerse cord plugs or appliance in water or other liquid Close supervision is necessary when the appliance is used by or near children Unplug from outlet when not in use and before cleaning Allow to cool before putting on or taking off parts and before cleaning the appliance Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Return appliance to the nearest authorized service facility for examination repair or adjustment The use of accessory attachments not recommended by the appliance manufacturer may result in fire electric shock or injury to persons Do not use outdoors Do not let cord hang over edge of table or counter or touch hot surfaces 10 Do not place on or near a hot gas or electric burner or in a heated oven ll Always attach plug to appliance first then plug cord into wall outlet To disconnect turn any
24. To brew a latte macchiato perform all steps for preparing a cappuccino up to step 4 We recommend using tall glasses for this type of preparation thus properly moving the dispensing spout When the machine is ready press the 8 button to start brewing the latte macchiato The machine prepares the latte macchiato automatically After using the Cappuccinatore clean it as described in the Cleaning the Cappuccinatore section See page 38 Remove the container or Thermos and clean it if necessary ENGLISH 25 Milk Handling With this machine you can prepare cappuccino latte macchiato and other milk based beverage quickly and enjoy your relax time You can use either the supplied Thermos or directly the milk container which can be purchase ad your local dealer s shop MILK MUST BE USED AND STORED IN ACCORDANCE WITH THE INSTRUC TIONS GIVEN ON THE MANUFACTURER S ORIGINAL PACKAGING WE ACCEPT NO LIABILITY FOR USE OF MILK UNSUITABLE FOR HUMAN CONSUMPTION Milk based beverages can only be prepared if the Cappuccinatore is installed Milk Thermos The machine is supplied with a Thermos specifically designed and built to improve milk storage since it limits the milk temperature increase The Thermos is only suitable for quick and easy domestic use It is not recom mended for continuous professional type operation To increase storage performance we recommend filling with cold milk approx 4 C Note Before usi
25. UCCINATORE HOSE IN A CONTAINER WITH 1 2 L WATER CAPPUCCINATORE CLEANING PLACE A CONTAINER UNDER THE DISPENSING SPOUT CAPPUCCINATORE CLEANING ENGLISH 45 EZ Fill the water tank and press the Y button to confirm IE Carefully wash the Thermos or the container used for the solution and fill it with 1 2 a half litre of fresh drinking water that will be used for rinsing Empty the container placed under the dispensing spout ET Insert the suction hose in the used container Press the S button to confirm OK Place an empty container under the dispensing spout and press the button to confirm R I The machine performs a rinse cycle of the Cappuccinatore The bar shows the rinsing progress Wait until the cycle stops automatically The machine will go back to the normal operating cycle EE Push the buttons located on the sides and remove the Cappuccinatore Wash all the Cappuccinatore parts as described on page 39 40 Wash all the Thermos parts if the Thermos has been used as de scribed on page 41 Important Note We recommend removing the Cappuccinatore when not be ing used in order to keep it clean 46 ENGLISH Weekly Cleaning Brew Grou The brew group should be cleaned every time the coffee bean hopper is filled or at least once a week Ell Turn off the machine by pressing the power button and remove the plug from the socket ER Remove
26. Y During the turning off phase the machine performs a rinse cycle if a cof fee product has been brewed Timecan be programmed according to your needs see page 34 OYA m eee To turn on the machine again simply press the button if the power button is set to I In this case the machine will perform the rinse cycle only if the boiler is cold Brewing Coffee Before brewing coffee check the lights on the display and make sure the water tank and coffee bean hopper are full Before brewing coffee adjust the height of the dispensing spout according to your needs and select the aroma by using the adjustment lever other wise select the pre ground coffee Cup warming Surface The machine features a cup warming surface to keep your cups warm and ready Warm cups bring out the full aroma of coffee and let you enjoy its taste in full Place the cups that you usually use and wait until they are warm Note the cup warming surface has a higher temperature than the other machine surfaces so we recommend not to touch it with sensitive body parts to avoid irritations Using the cup warming surface for other purposes is prohibited The cup warming surface is disabled by default for energy saving pur poses Refer to page 34 of the manual to activate is Adjusting the Dispensing Spout Most cups on the market can be used with this coffee machine The height of the dispensing spout may be adjusted to better fit the
27. and may used if care is exercised in their use Ifa long detachable power supply cord or extension cord is used 1 The marked electrical rating of the detachable power supply cord or extension cord should be at least as great as the electrical rating of the appliance 2 If the appliance is of the grounded type the extension cord should be a grounding type 3 wire cord and 3 The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over rper Tai lip E General Description fig 1 eere e eeeeeene IMPOrtant Intended Use Power Supply Power Cord For the Safety of Others Danger of Burns Machine Location Suitable Location for Operation and Maintenance Storing the Machine Cleaning Malfunction Fife Safety Precautions acsi etetenitoenipestpeend er thiet ottiene esed tbe i beet ettet bibas beste D bebe d 5 Uh hh Ja w w NICO d Packaging Preliminary Operation Double Function Button Setting the Language Upon First Use Warm up and Rinsing Rinse 5elf Cleaning Cyele iu uenia i srostbetrtnind ciiin beesosbl i o rv t cnra de 1 For a Perfect Espresso Rinse the Coffee Circuit if Using the Machine for the First Time or After a Fong Period of IactiVity eiecti Ed 10 Measuring and Adjusting Water Hardness 12 INTENZA Water Filter
28. ay and the coffee grounds drawer daily with the machine turned on Note We recommend cleaning the float and its seat to ensure perfect opera tion Note Other maintenance and cleaning operations can only be carried out when the machine is cold and disconnected from the electrical network Do not immerse the machine in water Do not wash any of the removable parts in the dishwasher except for the Cappuccinatore Do not use sharp objects or harsh chemical products solvents for clean ing Use a soft dampened cloth to clean the machine Do not dry the machine and or its parts using a microwave and or stan dard oven It is recommended to clean the water tank daily Remove the INTENZA water filter or remove the small white filter if you have not yet installed the INTENZA water filter from the water tank and wash it under running drinking water Reposition the INTENZA water filter or the small white filter if you have not yet installed the INTENZA water filter in its hous ing by gently pressing and turning it at the same time Fill the water tank with fresh drinking water EJ Empty and clean the drip tray daily Perform this operation also when the float is raised 38 ENGLISH E if you use the pre ground coffee compartment clean it every week with the supplied brush Cleaning the Cappuccinatore After Each Use The Cappuccinatore must be washed and cleaned every time it is used
29. cccccvccccsccccccccccccssccsssscsccccccccscsssssccesees 4O Weekly Cleaning Brew Group Brew Group Cleaning with Coffee Clean Tablets Brew Group Lubrication Descaling pec E LCD Display Warnings ee eeee eere e eere eene eene senes DD Troubleshooting eee cesser eee eee eee e eese senses esessees D 7 Technical Specifications e eeeeeeeeeeeeeeeee ees DO EN D ENGLISH 3 Introduction Congratulations on your purchase and welcome to Philips Saeco To fully benefit from the support that Philips offers register your product at www philips com welcome In this user manual you will find all the information you need to install use clean and descale your appliance In case you need further support please contact the toll free Philips consumer care help line You can find the phone number on the last page of this document and in the warranty booklet supplied with the appliance General Description fig 1 VO OO JA Ou P WM Cup warming surface Water tank Water tank lid Coffee dose adjustment Grinder adjustment Cappuccinatore cover Hot water wand Dispensing spout Brew group Service door Pre ground coffee compartment lid Coffee bean hopper lid Coffee bean hopper Cappuccinatore removable type Coffee grounds drawer Cup holder grill Full drip tray indicator Drip tray tray inner
30. ccinatore is placed in the machine Press the button OK Place a container under the hot water wand and a large enough con tainer under the Cappuccinatore Press the ei button UK 54 ENGLISH DESCALING STEP 2 2 IESC PAUSE EF The machine performs the rinse cycle Note A default amount of water is needed for the rinse phase This allows performing an ideal rinse cycle to ensure the best conditions to brew products The message about filling the tank for the rinse cycle is normal as it is part of the procedure Note The rinse cycle may be paused by pressing the Gg button To resume the cycle press the button again This allows you to empty the container or to go away for a short period of time EE Once the rinse cycle is complete the machine carries out the warm up and rinse cycle to prepare for product brewing Empty the containers used to collect the liquid dispensed by the ma chine and reassemble the dispensing spout The machine is now ready for use Note Thedescaling solution must be disposed of according to the manufac turer s instructions and or regulations in force in the country of use After completing the descaling cycle 1 Wash the brew group as described in the Brew Group section in the Cleaning and Maintenance chapter 2 Rinsethe Cappuccinatore under running water When the descaling cycle is complete we recommend emptying the drip tray
31. ce For best use it is recommended to Choose a safe level surface where there will be no danger of overturn ing the appliance or being injured e Choose a location that is sufficiently well lit clean and near an easily ENGLISH 5 A reachable socket inches Provide for a minimum distance from the sides of the machine as shown in the illustration While switching on or off the machine we suggest placing an empty Es glass under the dispensing spout Sues Do not keep the machine at temperatures below 0 C Frost may damage 150 mm am Geet the machine Do not use the coffee machine outdoors mt ft Sr In order to prevent its housing from melting or being damaged do not SS place the machine on very hot surfaces and close to open flames Storing the Machine Cleaning Before cleaning the machine turn it off by pressing the 0 button and then by switching the power button to 0 Finally remove the plug from the socket Keep the machine at its best clean and store it properly Since the machine uses natural ingredients to brew beverages coffee beans water milk etc some residues of ground coffee or condensed wa ter could be present on its supporting surface For this reason we recom mend to periodically clean both the visible parts of the machine and the area beneath it Before storing the machine we strongly recommend to clean it Water left in the tank and or the water circuit for several da
32. covered in the above table or when the suggested solutions do not solve the problem Technical Specifications The manufacturer reserves the right to make changes to the technical specifications of the product Nominal voltage Power rating Power supply See label on the inside of the service door E IER Thermoplastic material Metal EIU P db NUT EE 336 x 380 x 450 EE 15kg Power cordilength is 5 err nennt eene reme ERE EFE RE ERFE RR EX RE ED 12m Fotto pang ek eoo n e iet eer pee ati Vl exe ene P RR Ee On the front Cappuccilatofe EE Special for cappuccino Watertank cM T E 2 2 litres Removable type Coffee bean hopper capacity jg ANEN nmm mme Coffee grounds drawer capacity cesses Pump pres EE Bolle EE Stainless steel type Safety EE Thermostats Thermal protectors The packing materials can be recycled Appliance Unplug the appliance and cut the power cord Deliver the appliance and power cord to a service center or public waste disposal facility This product complies with eu directive 2002 96 ec A The symbol mm on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could ot
33. ct the machine during transport We recommend keeping the packaging material for possible future transport Preliminary Operations Remove the drip tray with grill and the coffee machine from the packaging Place the machine in a place that meets the requirements described in the safety regulations BR Place the drip tray with grill into its seat on the machine Make sure the tray is fully inserted to its limit stop Note Insert the plug into the socket only when indicated and make sure the power button is on 0 Important Note Carefully read the explanations of all the warnings the machine displays to the user on the control panel LCD display section LCD Display Warnings ER Remove the lid from the water tank EJ Remove the water tank from its seat by only using the relevant handle ER Rinse and fill it with fresh water making sure that the MAX level indicated in the tank is not exceeded Place the water tank back into its seat and reposition the lid Fill the tank only with fresh non sparkling water Hot water or any other liquid may damage the tank and or the machine Do not operate the ma chine without water Make sure there is enough water in the tank ENGLISH 7 E Make sure the dispensing spout is in correct position Move it horizon tally until you hear the CLICK indicating the correct position If this is not done some product might leak out of the dispensing spout Fal Remove the coffee bean
34. cted Press the VC button to confirm KA Press the amp button to start the cleaning cycle of the Cappuccinatore WASH THE CAPPUCCINATORE Note If this option is confirmed the cycle must be completed Press the Gg ESC button to exit until the Kor logo is displayed Fill the water tank and press the button to confirm REFILL WATER TANK 44 ENGLISH POUR DETERGENT INA CONTAINER WITH 1 2 L WATER CAPPUCCINATORE CLEANING PUT CAPPUCCINATORE HOSE IN THE CONTAINER zu PLACE A CONTAINER UNDER THE DISPENSING SPOUT CAPPUCCINATORE CLEANING EJ Pour a solution bag in the Thermos or in a container with 1 2 a half litre of fresh drinking water ER wait for the bag content to dissolve completely and then press the button to confirm E Insert the clean hose according to your choice intheThermos or directly in the container EE Press the i button to confirm Drinking the solution dispensed during this procedure is strictly forbidden The solution must be disposed of Place an empty container of at least 1 litre capacity under the dispens ing spout and press the Ef button to confirm OK EE The machine performs a wash cycle of the Cappuccinatore The bar shows the washing progress Wait until the cycle stops automatically CAPPUCCINATORE CLEANING REFILL WATER TANK INSERT CAPP
35. e suction tube removed from the Cappuccinatore while the descaling cycle is performed DESCALING DESCALING PLACE A CONTAINER UNDER MILK AND HOT WATER DISPENSERS DESCALING STEP 1 2 ESC PAUSE DESCALING RINSE TANK amp FILL WITH WATER EMPTY DRIP TRAY DESCALING INSERT THE CAPPUCCINATORE WITH ALL THE COMPONENTS DESCALING PLACE A CONTAINER UNDER MILK AND HOT WATER DISPENSERS ENGLISH 53 KI Place a container under the hot water wand and a large enough con tainer under the Cappuccinatore Press the eg button OK Note Use a container of at least 1 5 litre capacity If you do not have a container of this capacity pause the cycle by pressing the ah button empty the container place it back in the machine and restart the cycle by pressing the S button EE At this point the machine will start dispensing the descaling solution at intervals the bar shows the cycle progress EE When the solution in the tank is finished the machine requests to empty and rinse the tank with fresh drinking water EEJ Rinse the water tank thoroughly and refill it with fresh drinking water Insert the tank into the machine Press the JE button OK EE Empty the containers used to collect the liquid dispensed by the ma chine EE Remove any liquids from the drip tray and insert it back Press the gi button OK ET Check that the Cappu
36. g Do not pour ground and or instant coffee into the cof fee bean hopper Do not insert any material other than coffee beans into the hopper The grinder contains moving parts that may be dangerous Therefore do not insert fingers and or other objects Turn off the machine by pressing the ON OFF button and remove the plug from the socket before carrying out any type of operation inside the coffee bean hopper The machine allows you to make slight adjustments to the coffee grinder to adapt it to the kind of coffee used To make any adjustment use the lever located on the side of the machine Turn the lever one notch at a time and brew 2 3 cups of coffee this is the only way to notice differences in grind The reference marks indicate the grind setting You can set different de grees of grind with the following references 1 Fine Grind 2 Coarse Grind Adjusting the Aroma Amount of Ground Coffee The machine allows you to program the amount of coffee to be ground for preparing each cup of coffee Warning The Aroma adjustment lever must only be turned when the coffee grinder is stopped Adjustment must be performed before brewing coffee To make any adjustment use the lever located on the side of the machine The reference marks indicate the amount of ground coffee which has been set You can set different amounts with the following references 3 Minimum coffee amount about 7 grams 4 Maximum coffee amount abou
37. hat are located in the base of the Intenza filter The filter must be adjusted according to this measurement EJ The numbers correspond to the settings indicated in the following machine adjustments More precisely 1 very soft water 2 soft water hard water 3 4 very hard water ER Hold the e button pressed for 5 seconds to access the program ming mode H To select the MACHINE MENU option press the button Press the button for access OK KA Press the button until the WATER MENU option can be selected Press the ei button for access OK WATER MENU HARDNESS ENABLE FILTER ACTIVATE FILTER NAA ENGLISH 13 Press the button to enter the HARDNESS menu Note The machine is supplied with a standard adjustment suitable for most of the uses EJ Press The GM button to increase the value or the Ce button to reduce the value x ER Press the button to confirm the selected change Kl Press the button until the following product brewing page is displayed 14 ENGLISH INTENZA Water Filter The INTENZA water filter can improve the quality of water Using the INTENZA filter will prevent limescale from building up and will ensure a much more intense aroma to your espresso coffee We therefore recom mend you to install the INTENZA water filter You can purchase it at your local dea
38. he Cappuccinatore while fitting A is to be properly connected to the Thermos Note The fittings cannot be exchanged as this could cause the system to malfunction ER Remove the suction tube that is installed in the Cappuccinatore ENGLISH 27 Kl Insert the hose fitting in the Thermos Insert the fitting in the Cappuccinatore The Thermos can now be used to brew milk based products Milk Container The milk container can be used directly with the machine to prepare the beverages BB For direct use of the milk container it is necessary to use the Cappucci natore suction tube This tube only features one fitting Check that the tube is inserted in the Cappuccinatore Warning In this case make sure that the tube is clean on the outside as well to prevent milk from coming into contact with the dirt on the outside of the tube EJ Remove the clean suction tube and insert it directly into the container Note After use remove the tube and wash it properly Place the container back in the fridge for correct milk storage 28 ENGLISH SPECIAL Products The machine is designed to brew other products not displayed on the control panel Note After pressing the a button if no product is selected the machine goes back to the main menu after 10 seconds El Press the oe button to enter the menu LN D gt Cw B FA The display shows the page for special beverages ok ssc EJ Select t
39. he desired beverage by pressing the iy or SO button ER When the desired beverage has been selected press the button A FER to start the preparation Refer to the relevant section about brewing the desired beverage Note If no selection is carried out within 10 seconds the machine goes back to LONG COFFEE the home page HOT MILK AMERICAN COFFEE In order to prepare milk based beverages install the Cappuccinatore and the Thermos if necessary after washing them as described in the Cleaning and Maintenance section Dispensing Hot Water Dispensing may be preceded by short spurts of hot water Risk of burning The hot water wand may reach high temperatures The Hot water wand may reach high temperatures HOT WATER LONG COFFEE HOT MILK ER Press the ae button to enter the menu AMERICAN COFFEE FJ Place a container under the hot water wand Ell Press the button to start the preparation ER After dispensing remove the container with hot water HOT WATER Note You can stop dispensing by pressing the EN button rg ESC i STOP HOT WATER ENGLISH 29 Long Coffee SPECIAL BEVERAGES HOT WATER LONG COFFEE HOT MILK AMERICAN COFFEE This programme allows you to prepare a long coffee Note In this case you can just prepare one coffee at a time ER Press the button to enter the menu ES Press the bu
40. herwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product We want to ensure that you remain satisfied with your Philips Saeco Es presso coffee machine If not done already please register your purchase on www philips com welcome so that we can stay in contact with you and send you cleaning and descaling reminders For cleaning and descaling use SAECO products only You can purchase these on line at the Philips on line shop at NLhttpz shop philips nl BEhttp shop philips be FR http shop philips fr DK http shop philips dk DEhttp shop philips de ES http shop philips es or http tienda philips es IT http shop philips it SE http shop philips se If you have questions about your appliance e g about its installation use cleaning or descaling please refer to this user manual or go for the latest updates to www philips com support Alternatively you may contact our toll free consumer care help line at the phone number listed on the last page of this document Our qualified service staff will help you and if needed trouble shoot your appliance by phone and where possible provide a solution during the call If this is not possible we will help you to initiate any necessary repair in the shortest possible time
41. iler After priming the circuit with cold boiler During the stand by preparation phase if at least a coffee product has been brewed During the turning off phase after pressing the O button if at least a coffee product has been brewed RINSING A small amount of water will be dispensed to rinse and heat all the ma D x chine parts in this phase this icon is displayed ESC STOP RINSING Wait for the cycle to finish automatically You can stop dispensing by press ing the eo button ESC For a Perfect Espresso Rinse the Coffee Circuit if Using the Machine for the First Time or After a Long Period of Inactivity These simple operations will make it possible to always brew excellent cof fee They have to be performed A At first start up B When the machine remains inactive for a long time more than 2 weeks BER Place a large container under the dispensing spout E Empty the water tank wash and rinse it and fill it with fresh water EJ select the pre ground coffee brewing function by pressing the e button once M ok PHILIPS e Saeco The display indicates that the pre ground function has been selected O O f9 MENU OK PHILIPS e Saeco INSERT GROUND COFFEE AND PRESS OK ESC Esc co SPECIAL BEVERAGES HOT WATER LONG COFFEE HOT MILK AMERICAN COFFEE HOT WATER y Gr x gt STOP HOT WATER N
42. in the control panel have a double function The double function is only activated in certain moments during the ma chine operation or when accessing the programming mode The additional function is indicated by the icon under the machine button Pre ground coffee selection MENU Button This button allows you to select the coffee brew mode with pre ground coffee 2 4 Function Hold it pressed for 5 seconds to access the machine pro gramming menu Coffee Brew OK Button This button allows you to select one coffee brewing 2 4 Function Press it to select the displayed option Special Beverages Selection ESC Button This button allows you to access the list of special beverages that the machine can brew 2 4 Function Press it to exit the selected page and or the programming mode completely and or to stop brewing the beverage CLEAN A This button allows you to perform a cleaning cycle of the Cappuccinatore by dispensing steam see the special section for further details 2 4 Function Press it to scroll the current page selection up Cappuccino Brew Button V This button allows you to select the cappuccino brewing 2 4 Function Press it to scroll the current page selection down ITALIANO ENGLISH DEUTSCH FRANCAIS One Touch HEATING UP 4 EH 3OJ DR gt STOP RINSING ENGLISH 9 Setting the Language Upon First
43. k presence If necessary fill in the Thermos again or replace the milk container with a new one milk Thermos internal tube is not present The Brew Group cannot be removed The Brew Group is out of place Install the tube in the Thermos lid Turn the machine on Close the service door The brew group automatically returns to the initial position The coffee grounds drawer is inserted The machine grinds the coffee beans but no coffee comes out The Brew Group is dirty Remove the coffee grounds drawer before removing the brew group Clean the Brew Group Brew Group section See note The dispensing spout is dirty Coffee is too weak Too low dose See note Coffee is brewed slowly See note The coffee grind is too fine The Brew Group is dirty Coffee leaks out of the dispensing The dispensing spout is clogged or in spout the wrong position Clean the dispensing spout Adjust the amount of coffee to be ground Change coffee blend or adjust the grind as explained in section Adjusting the Coffee Grinder Clean the Brew Group Brew Group section Clean the dispensing spout and its holes Position the dispensing spout correctly Note These problems can be considered normal if the coffee blend has been changed or if the machine has just been installed Please contact our consumer care help line at the phone number listed at the last page of this document for any problems not
44. ler on line at the Philips on line shop at http shop philips com or at the authorised service centres BR Remove the small white filter from the tank and store it in a dry place sheltered from dust Measuring water hardness is very important in order to correctly manage the INTENZA water filter and the frequency with which the machine must be descaled Remove the INTENZA water filter from its package The filter should be set according to the measurements performed to set water hard ness Use the water hardness test strip provided with the machine Set the Intenza Aroma System as specified on the filter package see section Measuring and Adjusting Water Hardness A Soft water B Hard water standard C x Very hard water EJ Immerse the INTENZA water filter vertically with the opening posi tioned upwards in cold water and delicately press its sides so as to let the air bubbles out E Put the filter into the empty tank Press it until its limit stop ES Fill the tank with fresh drinking water and reinsert it into the machine MENU BEVERAGE MENU MACHINE MENU GENERAL MENU DISPLAY MENU WATER MENU MAINTENANCE MACHINE MENU GENERAL MENU DISPLAY MENU WATER MENU MAINTENANCE HARDNESS ENABLE FILTER ACTIVATE FILTER ACTIVATE FILTER ACTIVATE FILTER E ESC ACTIVATE FILTER INSERT F
45. lls up the menu MACHINE MENU Se button W scrolls down the menu ECK button ESC confirms when you exit a selection MENU BEVERAGE MENU MACHINE MENU FJ Press the amp button and the button to confirm the selection and enter the MACHINE MENU 34 ENGLISH General Menu GENERAL MENU To change the machine operating settings ECOMODE N STAND BY SETTINGS 15 MINUTES 30 MINUTES 60 MINUTES 180 MINUTES CUP WARM SURFACE This function activates deactivates the acoustic alarms To deactivate the acoustic alarms To activate the acoustic alarms This function enables activating the boilers on the machine to allow saving energy This function activates all the boilers at every ma chine start up to be immediately able to prepare all kinds of beverages The power consumption is higher this way because the machine is always ready for use This way only the coffee boiler is activated at machine start up The machine saves energy but needs longer time to dispense milk based bever ages To set the time interval for the machine to go into stand by mode after the last brewing The default time value is after 30 minutes Once the set time has elapsed the machine goes into stand by mode Press any button to turn the machine on again After performing the function diagnostics and the warm up phase the machine is again ready for use This function allo
46. ly in the machine can be found on page 47 point 7 8 9 and 10 of the section Weekly Cleaning Brew Group ER Insert the coffee grounds drawer and the drip tray Close the service door ENGLISH 51 NAA D 4 CALC OVAL SS MAINTENANCE BREW GROUP CLEAN DESCALING CAPPUCCINATORE CLEANING Limescale is a natural part of the water used for the machine operation It needs to be removed regularly as it may clog the water and coffee circuit of your appliance This is an easy procedure with your Philips Saeco machine The advanced electronics tells you on the display of the machine in clear symbols when descaling is needed Just follow the steps described below Not doing this will ultimately make your appliance stop working properly and in this case repair is not covered under your warranty Use the Saeco descaling product only Its formula has been designed to ensure better machine performance and operation for its whole operating life If correctly used it also avoids alterations in the brewed product The descaling solution and the complete Maintenance Kit may be purchased at your local dealer at the Philips on line shop at http shop philips com or at authorised service centres Warning Never drink the descaling solution or any products dispensed until the cycle has been carried out to the end Never use vinegar as a descaling solution E Turn on the machine by pressing the
47. m BREW GROUP CLEAN INSERT GROUP CLEAN TAB BREW GROUP CLEAN PLACE A CONTAINER UNDER THE DISPENSING SPOUT BREW GROUP CLEAN Brew Group Lubrication ENGLISH 49 Insert the cleaning tablet into the pre ground coffee compartment and press the e button to confirm OK EJ Place a container under the dispensing spout and press the but ton to confirm ER The machine completes the cycle automatically Note Once the cycle is complete the machine goes back to its normal operat ing mode Lubricate the Brew Group after approximately 500 cups of coffee or once a month The grease to lubricate the Brew Group and the complete Service Kit may be purchased at your local dealer at the Philips on line shop at http shop philips com or at authorised service centres Note To display the number of coffee cups brewed please refer to the COUN TERS menu in the BEVERAGE PROGRAMMING menu Before lubricating the brew group clean it under running water as described in the chapter Weekly Cleaning Brew Group 50 ENGLISH BR Lubricate the brew group guides using the Saeco grease only Apply the grease evenly on both side guides Lubricate also the shaft EJ Insert the Brew Group in its seat again until it locks into place WITHOUT pressing the PRESS button Note the detailed instructions to prepare the brew group and insert it correct
48. nemzeti m rt k Malaysia 1800 880 180 01800 504 6200 n mero gratuito 0900 202 11 77 0 10 min 22971950 nasjonale Tariffnr 0800 180 016 f r Anrufe aus dem sterreichischen Festnetz kostenfrei 0820401132 f r Anrufe aus dem sterreichischen Mobilfunknetz kostenpflichtig Preis variiert je nach Mobilfunkanbieter Norway Poland 22 397 15 06 Stawke lokalna Portugal 707780226 0 12 0 30 m vel Romania 031 6300043 accesibil din orice re ea cu tarif local Russia Poccua 7 495 961 1111 6e3 BbIXOAHbIX 8 800 200 0880 6e3 BbIXOAHbIX 3BOHOK GecnnarHbiil B Lu c Mo wnbHbIx Tene oHoB Singapore 65 68823999 Slovenija 01 888 83 13 nacionalnih tarif Slovensk republika 2 332 155 70 vn tro t tne tarifa Suomi 09 88 62 50 41 kansallisten kutsu South Africa 021 425 6169 Sverige 0857929067 nationella samtal Switzerland 0800 002 050 f r Anrufe aus dem schweizer Festnetz kostenfrei 0848 000 292 f r Anrufe aus dem schweizer Mobilfunknetz kostenpflichtig Preis variiert je nach Mobilfunkanbieter Ukraine 0 800 500 697 yci A3B HKN 3 crauionapuux TenedouiB B Mexax Ykpaiuw be3KOWTOBHi United Arab Emirates Dubai 971 4 2310300 0844 338 04 89 0 05GBP minute 1 800 933 7876 toll free 0800 231099 6626528652 Thailand
49. ng the Thermos make sure it is thoroughly clean and sanitary If there is milk left in the Thermos make sure it is still suitable for food con sumption before using it Do not use the Thermos to heat any beverage other than milk The container must be removed at least once a month to allow proper cleaning of all parts In this way you can keep a high sanitation level of the brewed beverages For correct cleaning refer to the CLEANING THE THERMOS section see pages 41 43 Warning Before using the Thermos clean it as described in the Cleaning and Maintenance section See page 37 For correct storage milk needs to be kept at low temperatures The Ther mos allows you to keep milk out of the fridge as long as it is necessary for its correct use At an ambient temperature of 20 C the temperature of the milk in the Thermos increases by 4 6 C after 4 hours Consider this approximate data to determine if milk can still be used in relation to the time it has been stored in the Thermos 26 ENGLISH BR Loosen and remove the Thermos lid Pour milk into the Thermos Fill in with milk from the MIN level indica tor and do not exceed the MAX level indicator EJ Reinsert the Thermos lid by screwing it EJ Use only the supplied hose to connect the Thermos to the Cappuccina tore This hose features two special fittings for optimum operation The fittings are different from each other i e fitting B is to be connected to t
50. o according to your taste and or the size of your cups Each time the d o B button is pressed and released the machine brews a pre set amount of Cappuccino or Latte macchiato This amount may be reprogrammed according to your taste Each button may be indi vidually programmed for a specific brew setting Note Before programming you need to prepare the machine and milk as described in the Cappuccino section Note As an example the following procedure describes the programming of the button which is normally associated with cappuccino BER Place a cup or a mug under the dispensing spout Press and hold the GH button until the MEMO message is dis played and remove your finger The machine is now programming The machine begins the milk dispensing phase The STOP MILK mes sage is displayed Ell From now on press the amp button when the desired amount of milk ESC is reached in the cup El immediately after the machine begins the coffee brewing phase The STOP COFFEE message is displayed E From now on press the amp button when the desired amount of cof S fee is reached in the cup Now the button has been programmed each time it is pressed and released the machine will brew the same amount that has just been set ENGLISH 19 Eco friendly Stand b The machine is designed for energy saving The machine automatically turns off after 30 minutes of inactivity Cen L I Note
51. scaling menu and refer to the relevant section Press the ech button to go on using the machine We remind you that damages caused by failure to descale the machine are not covered by warranty ENGLISH 57 Troubleshooting Machine actions Causes The machine does not switch on The machine is not plugged and or the power button is positioned on 0 Coffee is not hot enough The cups are cold Solutions Plug the machine and or switch the power button to I Preheat the cups with hot water Cup warming surface deactivated The blend is unsuitable coffee is not freshly roasted or the grind is too coarse Coffee has not enough crema See note The machine takes a long time to warm up or the amount of water dispensed from the wand is too little The machine circuit is clogged by limescale Bubbles form at the Cappuccina tore spout while dispensing milk The tube fittings are not connected properly or are not completely inserted in the Cappuccinatore and or Thermos There is no milk in the Thermos and or container any more Steam comes out of the Cappuc cinatore when the Thermos is connected and or when sucking Activate the cup warming surface and wait for the cups to warm Change coffee blend or adjust the grind as explained in section Adjusting the Coffee Grinder Descale the machine Insert the suction tube completely in the Cappuccinatore and or Thermos if used Check for mil
52. t 11 grams ENGLISH 17 Adjusting the Coffee Length gt STOP COFFEE The machine allows you to adjust the amount of brewed coffee according to your taste and or the size of your cups Note This function cannot be used to adjust American coffee length this prod uct requires using the specific menu in the BEVERAGE MENU Each time the y or y button is pressed and released the machine brews a pre set amount of coffee This amount may be reprogrammed according to your taste Each button may be individually programmed for a specific brew setting Note As an example the following procedure describes the programming of the lr button which is usually associated with espresso coffee BER Place a cup under the dispensing spout Press and hold the En button until the MEMO message is dis played and remove your finger The machine is now programming The machine begins the brewing phase The STOP COFFEE message is displayed EJ From now on press the button when the desired amount of cof fee is reached in the cup Now the e button has been programmed each time it is pressed and released the machine will brew the same amount that has just been set 18 ENGLISH Adjusting the Cappuccino or Latte Macchiato Length MEMO p gt mM gt STOP MILK Kl es gt STOP COFFEE The machine allows you to adjust the brewed amount of Cappuccino or Latte Macchiat
53. th the machine on press the O button EJ Press the e button to start the cleaning cycle for the Cappuccinato re Note To exit the cycle at any moment press the u button ET The machine warms the system up Once the warm up is complete the machine performs an assisted wash cycle for the Cappuccinatore Wait until the cycle is complete The wash cycle is now complete Refer to the following section for a thorough cleaning ENGLISH 43 Monthly Cleaning Cappuccinatore Thermos Thorough Cleaning Clean all the Cappuccinatore and Thermos parts thoroughly every month using the Saeco detergent supplied with the machine The Saeco deter gent may be purchased at your local dealer at the Philips on line shop at http shop philips com or at authorised service centres The lack of cleaning before and after each use can affect the correct opera tion of the machine Danger of burning Dispensing may be preceded by small jets of hot water E Make sure the Cappuccinatore is correctly placed Press and hold e E button for 5 seconds to enter the machine main menu EJ Press the So button and select the MACHINE MENU option press the E button to enter the menu E Press the amp button and select the MAINTENANCE option press the gp button to enter the menu BREW GROUP CLEAN i DESCALING H Press the button until the CAPPUCCINATORE CLEANING option CAPPUCCINATORE CLEANING can be sele
54. tically when the set level is reached However it is possible to stop the coffee brewing by pressing the a button gt Note The machine is adjusted to brew a true Italian espresso coffee This feature may slightly lengthen the brewing time allowing the intense coffee flavour to develop fully Using Pre ground Coffee This function allows using pre ground coffee Pre ground coffee must be poured into the relevant compartment posi tioned next to the coffee bean hopper Only use ground coffee for espresso machines and never coffee beans or instant coffee Note If no pre ground coffee is poured into the compartment only water will be dispensed If the dose is excessive and 2 or more measuring scoops of coffee are used the machine will not brew the product Also in this case the machine will run an empty cycle and discharge any ground coffee into the coffee grounds drawer 22 ENGLISH Oo PHILIPS e Saeco NAT w JOYA PHILIPS 2Saeco INSERT GROUND COFFEE AND PRESS OK ESC Esc MENU PHILIPS e Saeco To brew coffee Kl Press and release the button to select and activate the pre ground coffee function This page indicates that the function has been activated Note If the brewing is not started within 10 seconds the machine goes back to the coffee beans operating mode and displays the So symbol Press and release The nw button for a c
55. tton to select LONG COFFEE EJ Place a suitable cup under the dispensing spout ER Press the amp button to start the preparation Ell After brewing remove the coffee cup Hot Milk This programme allows you to prepare a hot milk Danger of burning Dispensing may be preceded by small jets of hot water BR Remove the cover from the front side Insert the complete Cappuccinatore into its seat until it locks into place Check that it cannot slide away EJ Insert the clean hose according to your choice inthemilkThermos or directly in the milk container Note To ensure better results use cold milk 30 ENGLISH SPECIAL BEVERAGES HOT WATER LONG COFFEE HOT MILK AMERICAN COFFEE SPECIAL BEVERAGES HOT WATER LONG COFFEE HOT MILK AMERICAN COFFEE El Press the R I button to enter the menu ES E Press the button to select HOT MILK BS Place a suitable cup under the dispensing spout Confirm by pressing the button to start the preparation Note You can stop dispensing by pressing the SEN button EJ After dispensing remove the cup with milk After using the Cappuccinatore clean it as described in the Cleaning the Cappuccinatore section See page 38 Remove the container or Thermos and clean it if necessary American Coffee This programme allows preparing and American coffee ER Press the ay button to enter the men
56. u Press the e button to select AMERICAN COFFEE EJ Place a suitable cup under the dispensing spout EJ Press the button to start the preparation H After brewing remove the coffee cup ENGLISH 31 Beverage Programming All beverage settings can be customized BR Press and hold the amp button for 5 seconds to access the machine main menu When you enter the programming mode the buttons have a different PHILIPS f ti unction e Saeco MENU button 0K confirms a selection or a change you have made BEVERAGE MENU MACHINE MENU O button A scrolls up the menu button W scrolls down the menu Y uo button ESC confirms when you exit a selection Se F Press the e button to confirm the selection and enter the BEVER OK AGE MENU ESPRESSO COFFEE This function allows you to set all parameters concerning a beverage brew CAPPUCCINO ing LATTE MACCHIATO Dispensed Beverages Counters This menu enables checking how many products have been brewed Press the button until the COUNTERS option is selected LATTE MACCHIATO SPECIAL BEVERAGES COUNTERS Press the e button to enter the option and display the number of brew ing procedures performed for each product This section which is displayed as the last option in the COUNTERS LATTE MACCHIATO menu allows you
57. up of espresso or the d button for a cup of long espresso Note If the brewing is not started within 30 seconds after the page is displayed or in case the button is pressed the machine returns to the main menu and discharges any inserted coffee into the coffee grounds drawer ES Lift the pre ground coffee compartment lid Warning Add only pre ground coffee to the compartment Other sub stances and objects may cause severe damages to the machine Such damages will not be covered by warranty Add only 1 scoop of pre ground coffee to the compartment Use only the measuring scoop supplied with the machine to perform this opera tion Then close the lid ER Press the button The brewing cycle starts Once the prebrewing cycle is complete coffee begins to come out of the dispensing spout Ell Coffee brewing stops automatically when the set level is reached However it is possible to stop the coffee brewing by pressing the uv button E After brewing the product the coffee beans configuration of the ma chine is restored Note Repeat the steps described above to brew other coffees ENGLISH 23 Brewing Cappuccino The machine allows brewing cappuccino quickly and easily with the touch of a button Danger of burning Dispensing may be preceded by small jets of hot water Important Note Immediately after using the Cappuccinatore to froth milk clean the suction hose externally with a damp cloth This
58. ws activating deactivating the cup warm ing surface located on the upper part of the machine To deactivate the cup warming surface To activate the cup warming surface ENGLISH 35 Display Menu DISPLAY MENU LANGUAGE adjusting the parameters of the machine according to the country where the machine is used The currently selected language is displayed ENGLISH The language can be changed with the special controls To set the correct display brightness according to the room BRIGHTNESS illumination To set the correct display contrast according to the room CUu illumination Water Menu WATER MENU To change the machine water hardness setting HARDNESS With the Hardness function you can adjust your machine to the level of hardness of the water you use so that the machine will request descaling at the right moment Measure water hardness as shown on page 12 This menu allows you to set the menu language and the display brightness and contrast This setting is of fundamental importance for correctly This menu allows setting correct water parameters for coffee brewing To activate deactivate the warning signal to replace the ENABLE FILTER water filter By activating this function the machine notifies the user when the water filter needs to be replaced OFF Warning disabled ON Warning enabled this value is automatically set when the filter is activated ACTIVATE FILTER To activate the filter
59. ys should not be consumed If the machine is going to remain inactive for a long time dispense water from the hot water wand and carefully clean the Cappuccinatore if supplied Turn off the power button and clean the machine Finally remove the plug from the socket Wait for the machine to cool down Never immerse the machine in water Store it in a dry place out of the reach of children Keep it protected from dust and dirt It is strictly forbidden to tamper with the internal parts of the machine For thorough cleaning the Cappuccinatore can be detached and disassem bled and its parts can be put in a dishwasher not professional type The washing process in the dishwasher may cause the surface of the Cap puccinatore parts to tarnish or the graphics to fade especially if aggressive detergents are used This is a normal phenomenon and does not affect in any way the correct operation of the milk system Malfunction In case of failure problems or a suspected fault resulting from the falling of the machine immediately remove the plug from the socket Never attempt to operate a faulty machine For further information on troubleshooting and service please refer to the Troubleshooting and Service chapters Fire Safety Precautions In case of fire use carbon dioxide CO extinguishers Do not use water or dry powder extinguishers 6 ENGLISH Packaging The original packaging has been designed and constructed to prote
Download Pdf Manuals
Related Search