Home

Asrock H77M

Contents

1. If the SATA SATA2 HDDs are NOT set for RAID configuration it is called Hot Plug for the action to insert and remove the SATA SATA2 HDDs while the system is still power on and in working condition However please note that it cannot perform Hot Plug if the OS has been installed into the SATA SATA2 HDD What is Hot Swap Function If SATA SATA2 HDDs are built as RAID 1 or RAID 5 then it is called Hot Swap for the action to insert and remove the SATA SATA2 HDDs while the system is still power on and in working condition 2 15 Hot Plug and Hot Swap Functions for SATA3 HDDs This motherboard supports Hot Plug and Hot Swap functions for SATA3 in RAID AHCI mode Intel H77 chipset provides hardware support for Advanced Host controller Interface AHCI a new programming interface for SATA host controllers developed through a joint industry effort A NOTE What is Hot Plug Function If the SATA3 HDDs are NOT set for RAID configuration it is called Hot Plug for the action to insert and remove the SATA3 HDDs while the system is still power on and in working condition However please note that it cannot perform Hot Plug if the OS has been installed into the SATA3 HDD What is Hot Swap Function If SATA3 HDDs are built as RAID 1 or RAID 5 then it is called Hot Swap for the action to insert and remove the SATA3 HDDs while the system is still power on and in working condition 37 2 16 SATA SATA2
2. Max shared memory 1760MB see CAUTION 5 Three VGA Output options D Sub DVI D and HDMI see CAUTION 6 Supports HDMI 1 4a Technology with max resolution up to 1920x1200 60Hz Supports DVI with max resolution up to 1920x1200 60Hz Supports D Sub with max resolution up to 2048x1536 75Hz Supports Auto Lip Sync Deep Color 12bpc xvYCC and HBR High Bit Rate Audio with HDMI Compliant HDMI monitor is required see CAUTION 7 Supports HDCP function with DVI and HDMI ports Supports Full HD 1080p Blu ray BD HD DVD playback with DVI and HDMI ports 7 1 CH HD Audio with Content Protection Realtek ALC892 Audio Codec Premium Blu ray audio support Supports THX TruStudio PCIE x1 Gigabit LAN 10 100 1000 Mb s Realtek RTL8111E Supports Wake On LAN Supports LAN Cable Detection Supports Energy Efficient Ethernet 802 3az Supports PXE Rear Panel I O I O Panel 1 x PS 2 Keyboard Port 1 x D Sub Port 1 x DVI D Port 1 x HDMI Port 1 x Optical SPDIF Out Port 6 x Ready to Use USB 2 0 Ports 2 x Ready to Use USB 3 0 Ports 1 x RJ 45 LAN Port with LED ACT LINK LED and SPEED LED HD Audio Jack Rear Speaker Central Bass Line in Front Speaker Microphone see CAUTION 8 2 x SATA3 6 0 Gb s connectors support RAID RAID 0 RAID 1 RAID 5 RAID 10 Intel Rapid Storage and Intel Smart Response Technology NCQ AHCI and Hot Plug functions 2 x Rear USB 3 0 ports
3. Standard 67 c Set Startup type to Disable then Click OK Volume Shadow Copy Properties Local Computer General Log On Recovery Dependencies Service name VSS Display name Volume Shadow Copy Description Manages and implements Volume Shadow Copies a p used for backup and other purposes ff this service Path to executable Windows system 32 Startup type Disabled Help me confiqure service startup options Service status Stopped Stat You can specify the start parameters that apply when you start the service from here Start parameters C ee h C Reboot your system D After reboot please start to install motherboard drivers and utilities Windows 7 64 bit A Please request the hotfix KB2505454 through this link http support microsoft com kb 2505454 B After installing Windows 7 64 bit install the hotfix kb2505454 This may take a long time gt 30 mins C Reboot your system It may take about 5 minutes to reboot D Windows will install this hotfix then reboot by itself E Please start to install motherboard drivers and utilities 6 Finish 68
4. CrossFireX driver updates performance benefits of CrossFirex All three CrossFireX components a CrossFirex Ready graphics card a CrossFirex Ready motherboard and a CrossFirex Edition co processor graphics card must be installed correctly to benefit from the CrossFireX multi GPU platform 2 If you pair a 12 pipe CrossFirex Edition card with a 16 pipe card both cards will operate as 12 pipe cards while in CrossFirex mode 1 If a customer incorrectly configures their system they will not see the 2 7 1 Installing Two CrossFireX Ready Graphics Cards feature For other CrossFirex cards that AMD has released or will release in the future please refer to AMD graphics card manuals for detailed installation guide Different CrossFireX cards may require different methods to enable CrossFirex Step 1 Insert one Radeon graphics card into PCIE1 slot and the other Radeon graphics card to PCIE2 slot Make sure that the cards are properly seated on the slots 22 Step 2 Step 3 Connect two Radeon graphics cards by installing a CrossFire Bridge on the CrossFire Bridge Interconnects on the top of the Radeon graphics cards The CrossFire Bridge is provided with the graphics card you pur chase not bundled with this motherboard Please refer to your graphics card vendor for details Connect the DVI monitor cable to the DVI connector on the Radeon graph ics card on PCIE1 slot You may use t
5. Disk Management Shadow Copies used for backup and y og va plications other purposes If this service is Tablet PC Input Service Enables Tab Started Automatic Local stopped shadow copies will be Task Scheduler Enables aus Started Automatic Local ol unavailable for backup and the TCP IP NetBIOS Helper Provides su Started Automatic Local backup may fail If this service is Teleph Provides Tel M I TAR disabled any services that explicitly Sepriony role a i depend on it will fail to start Terminal Services Allows user Started Automatic Netwo Terminal Services Confi Terminal Se Manual Local Terminal Services User Allows ther Manual Local Themes Provides us Started Automatic Local Thread Ordering Server Provides or Manual Local TPM Base Services Enables acc Automatic D Local UPnP Device Host Allows UPn Manual Local User Profile Service This service Started Automatic Local VIA Karaoke digital mix Started Automatic Local 2 Volume Shadow Copy Manages an Started Manual rent ocal lt Windows Audio Manages au Started Automatic Local Windows Audio Endpoi Manages au Started Automatic Local Windows Backup Provides Wi Manual Local Windows CardSpace Securely en Manual Local Windows Color System The WesPlu Manual Local Windows Connect Now Act as a Reg Manual Local TE E aar ee ae EP E E E PRT m r m t Extended
6. ISRock H M User Manual Version 1 1 Published July 2012 Copyright02012 ASRock ING All rights reserved Copyright Notice No part of this manual may be reproduced transcribed transmitted or translated in any language in any form or by any means except duplication of documentation by the purchaser for backup purpose without written consent of ASRock Inc Products and corporate names appearing in this manual may or may not be regis tered trademarks or copyrights of their respective companies and are used only for identification or explanation and to the owners benefit without intent to infringe Disclaimer Specifications and information contained in this manual are furnished for informa tional use only and subject to change without notice and should not be constructed as a commitment by ASRock ASRock assumes no responsibility for any errors or omissions that may appear in this manual With respect to the contents of this manual ASRock does not provide warranty of any kind either expressed or implied including but not limited to the implied warran ties or conditions of merchantability or fitness for a particular purpose In no event shall ASRock its directors officers employees or agents be liable for any indirect special incidental or consequential damages including damages for loss of profits loss of business loss of data interruption of business and the like even if ASRock has been advised of the possibi
7. Intel R Smart Connect Technology keeps your e mail and social networks such as Twitter Facebook etc updated automatically while the computer is in sleep mode The default is Disabled 55 3 4 7 Super IO Configuration ASROCK UEFI SETUP UTILITY Serial Port Use this item to enable or disable the onboard serial port Serial Port Address Use this item to set the address for the onboard serial port Configuration options 3F8h IRQ4 and 3E8h IRQ4 Infrared Port Use this item to enable or disable the onboard infrared port Parallel Port Use this item to enable or disable the onboard parallel port Change Settings Use this item to select an optional setting for Super IO device Device Mode Use this item to change the Printer Port mode 56 3 4 8 ACPI Configuration ASROCK UEFI SETUP UTILITY Tomorrow s Technology Today Suspend to RAM Use this item to select whether to auto detect or disable the Suspend to RAM feature Selecting Auto will enable this feature if the OS supports it Check Ready Bit Use this item to enable or disable the feature Check Ready Bit ACPI HPET Table Use this item to enable or disable ACPI HPET Table The default value is Enabled Please set this option to Enabled if you plan to use this motherboard to submit Windows Vista certification PS 2 Keyboard Power On Use this item to enable or disable PS 2 keyboard to turn on the system from the power soft off mode PCI Devic
8. SATA3 HDD Hot Plug Feature and Operation Guide This motherboard supports Hot Plug feature for SATA SATA2 SATA3 HDD in RAID AHCI mode Please read below operation guide of Hot Plug feature carefully Before you process the SATA SATA2 SATA3 HDD Hot Plug please check below cable accessories from the motherboard gift box pack A 7 pin SATA data cable B SATA power cable with SATA 15 pin power connector interface A SATA data cable Red B SATA power cable SATA 7 pin The SATA 15 pin power 1x4 pin conventional connector connector Black connect power connector White to SATA SATA2 SATA3 HDD connect to power supply Caution 1 Without SATA 15 pin power connector interface the SATA SATA2 SATA3 Hot Plug cannot be processed 2 Even some SATA SATA2 SATA3 HDDs provide both SATA 15 pin power connector and IDE 1x4 pin conventional power connector interfaces the IDE 1x4 pin conventional power connector interface is definitely not able to support Hot Plug and will cause the HDD damage and data loss Points of attention before you process the Hot Plug 1 Below operation procedure is designed only for our motherboard which supports SATA SATA2 SATA3 HDD Hot Plug The SATA SATA2 SATA3 Hot Plug feature might not be supported by the chipset because of its limitation the SATA SATA2 SATA3 Hot Plug support information of our motherboard is indicated in the product spec on our website www asrock com 2 Mak
9. by pressing lt Ctl gt lt Alt gt lt Delete gt or by pressing the reset button on the system chassis You may also restart by turning the system off and then back on Because the UEFI software is constantly being updated the following UEFI setup screens and descriptions are for reference purpose only and they may not exactly match what you see on your screen 3 1 1 UEFI Menu Bar The top of the screen has a menu bar with the following selections Main To set up the system time date information OC Tweaker To set up overclocking features Advanced To set up the advanced UEFI features H W Monitor To display current hardware status Boot To set up the default system device to locate and load the Operating System Security To set up the security features Exit To exit the current screen or the UEFI SETUP UTILITY Use lt lt gt key or lt gt key to choose among the selections on the menu bar and then press lt Enter gt to get into the sub screen You can also use the mouse to click your required item 42 3 1 2 Navigation Keys Please check the following table for the function description of each navigation key Navigation Key s Function Description lt Moves cursor left or right to select Screens i Moves cursor up or down to select items To change option for the selected items lt Tab gt Switch to next function lt Enter gt To bring up the selected screen lt PGUP gt Go to the previo
10. components Option C C O which provides flexible options to adopt three dif ferent CPU cooler types Socket LGA 775 LGA 1155 SG LGA 1 The white throughholes are for Socket LGA 7 1155 1156 CPU fan Please be noticed that this motherboard supports Combo Cooler 19 2 5 Installation of Memory Modules DIMM This motherboard provides two 240 pin DDR3 Double Data Rate 3 DIMM slots and supports Dual Channel Memory Technology For dual channel configuration you always need to install two identical the same brand speed size and chip type memory modules in the DDR3 DIMM slots to activate Dual Channel Memory Technology Otherwise it will operate at single channel mode q It is not allowed to install a DDR or DDR2 memory module into DDR3 slot otherwise this motherboard and DIMM may be damaged ZN If you install only one memory module or two non identical memory modules it is unable to activate the Dual Channel Memory Technology a Some DDR3 1GB double sided DIMMs with 16 chips may not work on this motherboard It is not recommended to install them on this motherboard Installing a DIMM Please make sure to disconnect power supply before adding or removing DIMMs or the system components Step 1 Unlock a DIMM slot by pressing the retaining clips outward Step 2 Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot lt notch lt lt break notch lt break The DIMM only
11. for ASRock motherboards with CIR header Please refer to below procedures for the quick installation and usage of ASRock Smart Remote Step1 Find the CIR header located next to the USB 2 0 header on ASRock motherboard USB 2 0 header 9 pin black CIR header 4 pin gray Step2 Connect the front USB cable to the USB 2 0 header as below pin 1 5 and the CIR header Please make sure the wire assignments and the pin assignments are matched correctly Step3 Install Multi Angle CIR Receiver to the front USB port If Multi Angle CIR Receiver cannot successfully receive the infrared signals from MCE Remote Controller please try to install it to the other front USB port 3 CIR sensors in different angles 1 Only one of the front USB port can support CIR function When the CIR function is enabled the other port will remain USB function 2 Multi Angle CIR Receiver is used for front USB only Please do not use the rear USB bracket to connect it on the rear panel Multi Angle CIR Receiver can receive the multi direction infrared signals top down and front which is compatible with most of the chassis on the market 3 The Multi Angle CIR Receiver does not support Hot Plug function Please install it before you boot the system ASRock Smart Remote is only supported by some of ASRock s motherboards Please refer to ASRock s website for the motherboard support list http www asrock com 29 2 10 Jumpers Setup T
12. motherboard s components due to static electricity NEVER place your motherboard directly on the carpet or the like Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components 3 Hold components by the edges and do not touch the ICs 4 Whenever you uninstall any component place it on a grounded anti static pad or in the bag that comes with the component 5 When placing screws into the screw holes to secure the mother board to the chassis please do not over tighten the screws Doing so may damage the motherboard switched off or the power cord is detached from the power supply Failure to do so may Cause severe damage to the motherboard peripherals and or components Before you install or remove any component ensure that the power is 16 2 3 CPU Installation In order to provide the LGA 1155 CPU sock ets more protection and make the instal lation process easier ASRock has added a new protection cover on top of the load plate to replace the former PnP caps that were under the load plate For the installa tion of Intel 1155 Pin CPUs with the new protection cover please follow the steps below Before you insert the 1155 Pin CPU into the socket please check if the CPU surface is unclean or if there are any bent pins in the socket Do not force to insert the CPU into the socket if above situation is found Otherwise the CPU will be seriously damaged Step
13. or disable Deep Render Standby by Internal Graphics Device The default value is Enabled 5 3 4 3 South Bridge Configuration ASROCK UEFI SETUP UTILITY Tomorrow s Technology Today Onboard HD Audio Select Auto Enabled or Disabled for the onboard HD Audio feature If you select Auto the onboard HD Audio will be disabled when PCI Sound Card is plugged Front Panel Select Auto or Disabled for the onboard HD Audio Front Panel On Off Play Use this item to enable or disable On Off Play Technology The default value is Enabled When On Off Play is enabled Deep Sleep will be dis abled If you want to enable Deep Sleep please disable On Off Play first Onboard HDMI HD Audio This allows you to enable or disable the Onboard HDMI HD Audio feature Onboard LAN This allows you to enable or disable the Onboard LAN feature Deep Sleep Mobile platforms support Deep S4 S5 in DC only and desktop platforms support Deep S4 S5 in AC only The default value is Enabled in S5 Restore on AC Power Loss This allows you to set the power state after an unexpected AC power loss If Power Off is selected the AC power remains off when the power recovers If Power On is selected the AC power resumes and the system starts to boot up when the power recovers Good Night LED Use this item to enable or disable Power LED and LAN LED 52 3 4 4 Storage Configuration ASROCK UEFI SETUP UTILITY KJE K o Security Exit H W Mo
14. panel module to this header make sure the wire assignments and the pin assign ments are matched correctly l Please connect the chassis 4 pin SPEAKER 1 SPEAKER speaker to this header see p 13 No 17 DUMMY DUMMY 5V 33 Chassis and Power Fan Connectors Please connect the fan cables 4 pin CHA_FAN1 CHA_FAN_SPEED to the fan connectors and match 12V i see p 13 No 22 GND FAN SPEED CONTROL the black wire to the ground pin CHA FAN1 and CHA FAN2 3 pin CHA FAN2 EEE supports Fan Control 12V see p 13 No 31 afol PWR_FAN_SPEED 3 pin PWR_FAN1 oy see p 13 No 32 GND CPU Fan Connectors oo Please connect the CPU fan 4 pin CPU_FAN1 cable to the connector and see p 13 No 2 GNP match the black wire to the CPU_FAN_SPEED FAN_SPEED_CONTROL ground pin AN Though this motherboard provides 4 Pin CPU fan Quiet Fan support the 3 Pin CPU fan still can work successfully even without the fan speed control function If you plan to connect the 3 Pin CPU fan to the CPU fan connector on this motherboard please connect it to Pin 1 3 Pin 1 3 Connected lt 7 s 3 Pin Fan Installation 195 3 pin CPU FAN2 see p 13 No 3 m GND 12V CPU_FAN_SPEED ATX Power Connector iz Please connect an ATX power 24 pin ATXPWR1 supply to this connector see p 13 No 6 1 13 4 Though this motherboard provides 24 pin ATX power
15. to manage RAID functions you are allowed to use both RAID Installation Guide and Intel Rapid Storage Information for RAID configuration Please refer to the document in the Support CD Guide to SATA Hard Disks Installation and RAID Configuration which is lo cated in the folder at the following path RAID Installation Guide and the document in the support CD Guide to Intel Rapid Storage which is located in the folder at the follow ing path Intel Rapid Storage Information If you want to use Intel Rapid Storage in Windows environment install SATAII driver from the Support CD again so that Intel Rapid Storage will be installed to your system as well 40 2 19 Installing Windows 7 7 64 bit Vista Vista 64 bit XP XP 64 bit Without RAID Functions If you want to install Windows 7 7 64 bit Vista Vista 64 bit XP XP 64 bit OS on your SATA SATA2 SATA3 HDDs without RAID functions please follow below procedures according to the OS you install 2 19 1 Installing Windows XP XP 64 bit Without RAID Functions If you want to install Windows XP XP 64 bit OS on your SATA SATA2 SATA3 HDDs without RAID functions please follow below steps 4 AHCI mode is not supported under Windows XP XP 64 bit Using SATA SATA2 SATA3 HDDs without NCQ function STEP 1 Set Up UEFI A Enter UEFI SETUP UTILITY Advanced screen Storage Configuration
16. 1 Open the socket Step 1 1 Disengage the lever by pressing it down and sliding it out of the hook You do not have to remove the pro tection cover Step 1 2 Keep the lever positioned at about 135 degrees in order to flip up the load plate Step 2 Insert the 1155 Pin CPU Step 2 1 Hold the CPU by the edge which is marked with a black line aul 49e1q Step 2 2 Orient the CPU with the IHS Inte grated Heat Sink up Locate Pin and the two orientation key notches 17 orientation key notch alignment key alignment key orientation key notch 1155 Pin Socket 1155 Pin CPU For proper installation please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket Step 2 3 Carefully place the CPU into the socket Step 2 4 Verify that the CPU is within the sock et and properly mated to the orient keys Step 3 Close the socket Step 3 1 Flip the load plate onto the IHS Step 3 2 Press down the load lever and se cure it with the load plate tab under the retention tab The protection cover will automatically come off by itself Please save and replace the cover if the processor is removed The cover must be placed if you wish to return the motherboard for after service 18 2 4 Installation of CPU Fan and Heatsink This motherboard is equipped with 1155 Pin socket that supports Intel 1155 Pin CPUs Please adopt the type of heatsink and co
17. 2 contains introduction of the motherboard and step by step guide to the hardware installation Chapter 3 and 4 contains the configura Chapter 1 Introduction tion guide to BIOS setup and information of the Support CD Because the motherboard specifications and the BIOS software might be updated the content of this manual will be subject to change without no tice In case any modifications of this manual occur the updated version will be available on ASRock website without further notice You may find the latest VGA cards and CPU support lists on ASRock website as well ASRock website _http www asrock com If you require technical support related to this motherboard please visit our website for specific information about the model you are using www asrock com support index asp 1 1 Package Contents ASRock H77M Motherboard Micro ATX Form Factor 9 6 in x 8 5 in 24 4 cm x 21 6 cm ASRock H77M Quick Installation Guide ASRock H77M Support CD 2 x Serial ATA SATA Data Cables Optional 1 x I O Panel Shield OES S 3 ASRock Reminds You To get better performance in Windows 7 7 64 bit Vista Vista 64 bit it is recommended to set the BIOS option in Storage Configuration to AHCI mode For the BIOS setup please refer to the User Manual in our support CD for details 1 2 Specifications Micro ATX Form Factor 9 6 in x 8 5 in 24 4 cm x 21 6 cm All Solid Capacitor design Supports 3 and 2 Gene
18. 3 No 20 Print Port Header Ad 25 pin LPT1 see p 13 No 23 Front Panel Audio Header 9 pin HD AUDIO1 see p 13 No 30 A Besides two default USB 3 0 ports on the I O panel there is one USB 3 0 header on this motherboard This USB 3 0 header can support two USB 3 0 ports This header supports an optional wireless transmitting and receiving infrared module This header can be used to connect the remote controller receiver This is an interface for print port cable that allows convenient connection of printer devices This is an interface for front panel audio cable that allows convenient connection and control of audio devices 1 High Definition Audio supports Jack Sensing but the panel wire on the chassis must support HDA to function correctly Please follow the instruction in our manual and chassis manual to install your system 2 If you use AC 97 audio panel please install it to the front panel audio header as below A Connect Mic_IN MIC to MIC2_L B Connect Audio_R RIN to OUT2_R and Audio_L LIN to OUT2_L C Connect Ground GND to Ground GND 32 System Panel 9 pin PANEL1 see p 13 No 16 A Chassis Speaker Header D MIC RET and OUT RET are for HD audio panel only You don t need to connect them for AC 97 audio panel E To activate the front mic For Windows XP XP 64 bit OS Select Mixer Select Recorder Then click FrontMic F
19. 535 0XFFFF means indefinite waiting Bootup Num Lock If this item is set to On it will automatically activate the Numeric Lock function after boot up PCI ROM Priority Use this item to adjust PCI ROM Priority The default value is Legacy ROMI Full Screen Logo Use this item to enable or disable OEM Logo The default value is Enabled AddOn ROM Display Use this option to adjust AddOn ROM Display If you enable the option Full Screen Logo but you want to see the AddOn ROM information when the system boots please select Enabled Configuration options Enabled and Disabled The default value is Enabled Boot From Onboard LAN Use this item to enable or disable the Boot From Onboard LAN feature Boot Failure Guard Enable or disable the feature of Boot Failure Guard Boot Failure Guard Count Use this item to configure Boot Failure Guard Count 60 3 7 Security Screen In this section you may set or change the supervisor user password for the system For the user password you may also clear it ASROCK UEFI SETUP UTILITY Not Installed Not Installed Tomorrow s Technology Today 6 3 8 Exit Screen ASROCK UEFI SETUP UTILITY Tomorrow s Technology Today Save Changes and Exit When you select this option the following message Save configuration changes and exit setup will pop out Select Yes to save the changes and exit the UEFI SETUP UTILITY Discard Changes and Exit When you se
20. B Set the option SATA Mode Selection to IDE STEP 2 Install Windows XP XP 64 bit OS on your system 2 19 2 Installing Windows 7 7 64 bit Vista Vista 64 bit Without RAID Functions If you want to install Windows 7 7 64 bit Vista Vista 64 bit OS on your SATA SATA2 SATA3 HDDs without RAID functions please follow below steps Using SATA SATA2 SATA3 HDDs with NCQ function STEP 1 Set Up UEFI A Enter UEFI SETUP UTILITY Advanced screen Storage Configuration B Set the option SATA Mode Selection to AHCI STEP 2 Install Windows 7 7 64 bit Vista Vista 64 bit OS on your system Using SATA SATA2 SATA3 HDDs without NCQ function STEP 1 Set Up UEFI A Enter UEFI SETUP UTILITY Advanced screen Storage Configuration B Set the option SATA Mode Selection to IDE STEP 2 Install Windows 7 7 64 bit Vista Vista 64 bit OS on your system 41 Chapter 3 UEFI SETUP UTILITY 3 1 Introduction This section explains how to use the UEFI SETUP UTILITY to configure your system The UEFI chip on the motherboard stores the UEFI SETUP UTILITY You may run the UEFI SETUP UTILITY when you start up the computer Please press lt F2 gt or lt Del gt during the Power On Self Test POST to enter the UEFI SETUP UTILITY otherwise POST will continue with its test routines If you wish to enter the UEFI SETUP UTILITY after POST restart the system
21. COM Port Header COM1 SATA3 Connector SATA3_1 Gray 25 Infrared Module Header IR1 SATA3 Connector SATA3_0 Gray 26 PCI Express 2 0 x16 Slot PCIE2 Black SATA2 Connector SATA2_2 Black 27 PCI Slots PCI1 2 Black SATA2 Connector SATA2_3 Black 28 HDMI_SPDIF Header SATA2 Connector SATA2_4 Black HDMI_SPDIF1 Black SATA2 Connector SATA2_5 Black 29 PCI Express 3 0 x16 Slot PCIE1 Black SPI Flash Memory 64Mb 30 Front Panel Audio Header Intel H77 Chipset HD_AUDIO1 Black System Panel Header PANEL1 Black 31 Chassis Fan Connector CHA FAN2 Chassis Speaker Header SPEAKER1 Black 32 13 Power Fan Connector PWR FAN1 1 4 I O Panel 1 USB 2 0 Ports USB01 9 Front Speaker Lime 2 D Sub Port VGA1 10 Microphone Pink 3 USB2 0 Ports USB23 11 USB2 0 Ports USB45 4 LAN RJ 45 Port 12 USB 3 0 Ports USB3 23 5 Central Bass Orange 13 HDMI Port HDMI1 6 Rear Speaker Black 14 DVI D Port DVI1 7 Optical SPDIF Out Port 15 PS 2 Keyboard Port Purple 8 Line In Light Blue There are two LED next to the LAN port Please refer to the table below for the LAN port LED indications LAN Port LED Indications ACTILINK SPEED Activity Link LED SPEED LED LED LED Description 10Mbps connection 100Mbps connection 1Gbps connection LAN Port If you use 2 channel speaker please connect the speaker s plug into Front Speaker Jack See the table below for connection details in accordance with t
22. Drivers Menu The Drivers Menu shows the available device s drivers if the system detects installed devices Please install the necessary drivers to activate the devices 4 2 3 Utilities Menu The Utilities Menu shows the application softwares that the motherboard sup ports Click on a specific item then follow the installation wizard to install it 4 2 4 Contact Information If you need to contact ASRock or want to know more about ASRock welcome to visit ASRock s website at http www asrock com or you may contact your dealer for further information 63 Installing OS on a HDD Larger Than 2TB in AHCI Mode This motherboard adopts UEFI BIOS that allows Windows OS to be installed on a large size HDD gt 2TB Please follow the procedures below to install the operating system 1 Please make sure to use Windows Vista 64 bit with SP2 or above or Windows 7 64 bit with SP1 or above 2 Press lt F2 gt or lt Delete gt at system POST Set AHCI Mode in UEFI Setup Utility gt Advanced gt Storage Configuration gt SATA Mode 3 Choose the item UEFI xxx to boot in UEFI Setup Utility gt Boot gt Boot Option 1 xxx is the device which contains your Windows installation files Normally it is an optical drive You can also press lt F11 gt to launch boot menu at system POST and choose the item UEFI xxx to boot 4 Start Windows installation 64 Installing OS on a HDD Larger Than 2TB in RAID Mode
23. ION 17 Hybrid Booster ASRock U COP see CAUTION 18 Boot Failure Guard B F G Combo Cooler Option C C O see CAUTION 19 Good Night LED Hardware CPU Temperature Sensing Monitor Chassis Temperature Sensing CPU Chassis Power Fan Tachometer CPU Chassis Quiet Fan Allows Chassis Fan Speed Auto Adjust by CPU Temperature CPU Chassis Fan Multi Speed Control Voltage Monitoring 12V 5V 3 3V CPU Vcore Microsoft Windows 7 7 64 bit Vista Vista 64 bit XP XP 64 bit compliant see CAUTION 20 Certifications FCC CE WHQL ErP EuP Ready ErP EuP ready power supply is required see CAUTION 21 For detailed product information please visit our website http Awww asrock com WARNING Please realize that there is a certain risk involved with overclocking including adjusting the setting in the BIOS applying Untied Overclocking Technology or using third party overclocking tools Overclocking may affect your system s stability or even cause damage to the components and devices of your system It should be done at your own risk and expense We are not responsible for possible damage caused by overclocking CAUTION 1 About the settings of Hyper Threading Technology please check page 49 2 This motherboard supports Dual Channel Memory Technology Before you implement Dual Channel Memory Technology make sure to read the installation guide of memory modules on page 20 for pr
24. Monitor and Surround Display Features Dual Monitor Feature This motherboard supports dual monitor feature With the internal VGA output sup port DVI D D Sub and HDMI you can easily enjoy the benefits of dual monitor feature without installing any add on VGA cards to this motherboard This mother board also provides independent display controllers for DVI D D Sub and HDMI to support dual VGA output so that DVI D D sub and HDMI can drive same or different display contents To enable dual monitor feature please follow the steps below 1 Connect a DVI D monitor cable to the DVI D port on the I O panel connect a D Sub monitor cable to the D Sub port on the I O panel and connect a HDMI monitor cable to the HDMI port on the I O panel D Sub port DVI D port HDMI port 2 If you have already installed the onboard VGA driver from our support CD to your system you can freely enjoy the benefits of dual monitor function after your system boots If you haven t installed the onboard VGA driver yet please install the onboard VGA driver from our support CD to your system and restart your computer D Sub DVI D and HDMI monitors cannot be enabled at the same time You can only choose the combination DVI D HDMI DVI D D Sub or HDMI D Sub 26 Surround Display Feature This motherboard supports surround display upgrade With the internal VGA output support DVI D D Sub and HDMI and external add on PCI Express VGA cards you can
25. SATA2 SATA3 HDD side 39 2 17 Driver Installation Guide To install the drivers to your system please insert the support CD to your optical drive first Then the drivers compatible to your system can be auto detected and listed on the support CD driver page Please follow the order from up to bottom side to install those required drivers Therefore the drivers you install can work properly 2 18 Installing Windows 7 7 64 bit Vista Vista 64 bit With RAID Functions If you want to install Windows 7 7 64 bit Vista Vista 64 bit OS on your SATA SATA2 SATA3 HDDs with RAID functions please follow the steps below 4 RAID mode is not supported under Windows XP XP 64 bit STEP 1 Set up UEFI A Enter UEFI SETUP UTILITY Advanced screen Storage Configuration B Set the option SATA Mode Selection to RAID STEP 2 Use RAID Installation Guide to set RAID configuration Before you start to configure the RAID function you need to check the installation guide in the Support CD for proper configuration Please refer to the document in the Support CD Guide to SATA Hard Disks Installation and RAID Configuration which is located in the folder at the following path RAID Installation Guide STEP 3 Install Windows 7 7 64 bit Vista Vista 64 bit OS on your system After the installation of Windows 7 7 64 bit Vista Vista 64 bit OS if you want
26. SATA2_4 see p 13 No 12 lt lt od fj 3 SATA2 5 see p 13 No 13 Serial ATA3 Connectors SATA3 0 see p 13 No 9 SATA3 1 SATA3 1 see p 13 No 8 Serial ATA SATA Data Cable Optional USB 2 0 Headers 9 pin USB6 7 see p 13 No 19 9 pin USB8 9 see p 13 No 21 SATA2 3 ri SATA3 0 Ll I 1 SATA2 2 31 1 These four Serial ATA2 SATA2 connectors support SATA data cables for internal storage devices The current SATA2 interface allows up to 3 0 Gb s data transfer rate These two Serial ATA3 SATA3 connectors support SATA data cables for internal storage devices The current SATA3 interface allows up to 6 0 Gb s data transfer rate Either end of the SATA data cable can be connected to the SATA SATA2 SATA3 hard disk or the SATA2 SATA3 connector on this motherboard Besides six default USB 2 0 ports on the I O panel there are two USB 2 0 headers on this motherboard Each USB 2 0 header can support two USB 2 0 ports USB 3 0 Header IntA_PO_D IntA_PO_D PR USBS 0 1 NL tA PO SSTX see p 13 No 7 Ke IntA PO SSRX IntA PO SSRX Vbus IntA P1 SSRX IntA P1 SSRX GND IntA P1 SSTX IntA P1 SSTX GND IntA P1 D IntA P1 D DUMMY Infrared Module Header IRTX 5VSB 5 pin IR1 DUMMY see p 13 No 25 GND IRRX Consumer Infrared Module Header 4 pin CIR1 T SNC IRRX ATX 5VSB see p 1
27. This motherboard adopts UEFI BIOS that allows Windows OS to be installed on a large size HDD gt 2TB Please follow the procedures below to install the operating system 1 Please make sure to use Windows Vista 64 bit with SP2 or above or Windows 7 64 bit with SP1 or above 2 Copy Intel RAID drivers into a USB flash disk You can download the driver from ASRock s website and unzip the file into a USB flash disk OR copy the file from ASRock motherboard support CD please copy the files under following directory 32 bit i386 Win7_Vista_Intel_v11 0 0 1032 64 bit AMD64 Win7 64_Vista64_Intel_v11 0 0 1032 3 Create RAID array for you system Please refer to Intel RAID Installation Guide file for details 4 Install Windows Vista 64 bit 7 64 bit A Insert your Windows Vista 64 bit 7 64 bit installation disc to the optical drive B Press lt F11 gt to launch boot menu at system POST and choose the item UEFI xxx to boot C Start Windows Installation When you see Where do you want to install Windows page please click Load Driver D Plug the USB flash disk into your USB port select Browse to find the RAID driver Then choose the directory xx AMD64 you have copied in the first step 65 E Please keep the USB flash disk installed until the system s first reboot F Continue to install OS by following the Windows instructions 5 Follow Windows Installation Gu
28. according to your own requirements 47 3 4 Advanced Screen In this section you may set the configurations for the following items CPU Configu ration North Bridge Configuration South Bridge Configuration Storage Configura tion Intel R Rapid Start Technology Intel R Smart Connect Technology Super IO Configuration ACPI Configuration and USB Configuration ASROCK UEFI SETUP UTILITY E o Security Exit Boot Description Setting wrong values in this section may cause the system to malfunction Instant Flash Instant Flash is a UEFI flash utility embedded in Flash ROM This conve nient UEFI update tool allows you to update system UEFI without enter ing operating systems first like MS DOS or Windows Just save the new UEFI file to your USB flash drive floppy disk or hard drive and launch this tool then you can update your UEFI only in a few clicks without prepar ing an additional floppy diskette or other complicated flash utility Please be noted that the USB flash drive or hard drive must use FAT32 16 12 file system If you execute Instant Flash utility the utility will show the UEFI files and their respective information Select the proper UEFI file to up date your UEFI and reboot your system after the UEFI update process is completed 48 3 4 1 CPU Configuration ASROCK UEFI SETUP UTILITY Tomorrow s Technology Today Intel Hyper Threading Technology To enable this feature a computer syst
29. connector 12 it can still work if you adopt a traditional 20 pin ATX power supply To use the 20 pin ATX power supply please plug your power supply along with Pin 1 and Pin 13 20 Pin ATX Power Supply Installation 8 pin ATX12V1 power supply to this connector see p 13 No 1 ATX 12V Power Connector 5 E 1 Please connect an ATX 12V 34 Though this motherboard provides 8 pin ATX 12V power connector it can still work if you adopt a traditional 4 pin ATX 12V power supply To use the 4 pin ATX power supply please plug your power supply along with Pin 1 and Pin 5 3 Serial port Header 9 pin COM1 see p 13 No 24 HDMI_SPDIF Header 2 pin HDMI_SPDIF1 see p 13 No 28 4 Pin ATX 12V Power Supply Installation 8 GND SPDIFOUT 35 This COM1 header supports a serial port module HDMI_SPDIF header providing SPDIF audio output to HDMI VGA card allows the system to connect HDMI Digital TV projector LCD devices Please connect the HDMI_SPDIF connector of HDMI VGA card to this header 2 12 Serial ATA SATA Serial ATA2 SATA2 Hard Disks Installation This motherboard adopts Intel H77 chipset that supports Serial ATA SATA Serial ATA2 SATA2 hard disks and RAID RAID 0 RAID 1 RAID 5 RAID 10 Intel Rapid Storage and Intel Smart Response Technology functions You may install SATA SATA2 hard disks on this motherboard for internal storage devices This section wi
30. ct CrossFi rex and then check the item Enable CrossFireX Select 2 GPUs and click Apply performance on a single display by CrossFireX delivers exceptional mbining the processing power of two or more Graphics Processing Units combini GPUs Configure CrossFireX IV Enable CrossFireX Choose from the following Render GPU combinations 2GPUs 24 D Identify GPU A Your settings have not been applied To enable your other discard or apply CrossFireX adapter pages click on the dis buttons to refresh and save your settings RADEDN 24 Although you have selected the option Enable CrossFire the CrossFirex function may not work actually Your computer will automatically reboot After restarting your computer please confirm whether the option Enable CrossFire in ATI Catalyst Control Center is selected or not if not please select it again and then you are able to enjoy the benefits of CrossFirex Step 7 You can freely enjoy the benefits of CrossFirex or Quad CrossFireX CrossFireX appearing here is a registered trademark of AMD Technologies Inc and is used only for identification or explanation and to the owners benefit without intent to infringe For further information of AMD CrossFirex technology please check AMD s website for updates and details 25 2 8 Dual
31. does not support Intel SpeedStep technology stability or compatibility issues with some power supplies Please set this item to Please note that enabling this function may reduce CPU voltage and lead to system Disabled if above issues occur Intel Turbo Boost Technology Use this item to enable or disable Intel Turbo Boost Mode Technology Turbo Boost Mode allows processor cores to run faster than marked fre quency in specific conditions The default value is Enabled Internal PLL Overvoltage Use this item to enable disable CPU Internal PLL Overvoltage Function Long Duration Power Limit Use this item to configure long duration power limit in watts The default value is Auto Long Duration Maintained Use this item to configure time window which the long duration power is maintained The default value is Auto 44 Short Duration Power Limit Use this item to configure short duration power limit in watts The default value is Auto Primary Plane Current Limit Use this item to configure the maximum instantaneous current allowed for the primary plane The default value is Auto Secondary Plane Current Limit Use this item to configure the maximum instantaneous current allowed for the secondary plane The default value is Auto GT OverClocking Support Use this item to enable or disable GT OverClocking Support The default value is Disabled DRAM Timing Configuration Load XMP Setting Use this to load XMP setting Config
32. e default is Auto DRAM tCWL Use this item to change CAS Write Latency tCWL Auto Manual setting The default is Auto ODT WR CH A Use this item to change ODT WR CH A setting The default is Auto ODT WR CH B Use this item to change ODT WR CH B setting The default is Auto ODT NOM CH A Use this item to change ODT NOM CH A setting The default is Auto ODT NOM CH B Use this item to change ODT NOM CH B setting The default is Auto 46 MRC Fast Boot Use this item to enable or disable MRC Fast Boot The default is Enabled Voltage Configuration CPU Core Voltage Use this to select CPU Core Voltage The default value is Auto CPU Load Line Calibration CPU Load Line Calibration helps prevent CPU voltage droop when the system is under heavy load IGPU Voltage Use this to select IGPU Voltage The default value is Auto IGPU Load Line Calibration IGPU Load Line Calibration helps prevent IGPU voltage droop when the system is under heavy load DRAM Voltage Use this to select DRAM Voltage The default value is Auto VTT Voltage Use this to select VTT Voltage The default value is Auto PCH Voltage Use this to select PCH Voltage The default value is Auto CPU PLL Voltage Use this to select CPU PLL Voltage The default value is Auto VCCSA Voltage Use this to select VCCSA Voltage The default value is Auto User Defaults In this option you are allowed to load and save three user defaults
33. e sure your SATA SATA2 SATA3 HDD can support Hot Plug function from your dealer or HDD user manual The SATA SATA2 SATA3 HDD which cannot support Hot Plug function will be damaged under the Hot Plug operation 3 Please make sure the SATA SATA2 SATA3 driver is installed into system properly The latest SATA SATA2 SATA3 driver is available on our support website www asrock com 4 Make sure to use the SATA power cable amp data cable which are from our motherboard package 5 Please follow below instructions step by step to reduce the risk of HDD crash or data loss 38 How to Hot Plug a SATA SATA2 SATA3 HDD Points of attention before you process the Hot Plug Please do follow below instruction sequence to process the Hot Plug improper procedure will cause the SATA SATA2 SATA3 HDD damage and data loss Sie Please connect SATA power cable 1x4 a4 Connect SATA data cable to the pin end White to the power supply motherboard s SATA2 SATA3 1x4 pin cable connector Sk Connect SATA 15 pin power cable jeg Connect SATA data cable to connector Black end to SATA SATA2 the SATA SATA2 SATA3 HDD SATA3 HDD How to Hot Unplug a SATA SATA2 SATA3 HDD Points of attention before you process the Hot Unplug Please do follow below instruction sequence to process the Hot Unplug improper procedure will cause the SATA SATA2 SATA3 HDD damage and data loss Unplug SATA data cable from SATA
34. easily enjoy the benefits of surround display feature Please refer to the following steps to set up a surround display environment 1 Install the PCI Express VGA cards on PCIE1 and PCIE2 slots Please refer to page 21 for proper expansion card installation procedures 2 Connect a DVI D monitor cable to the DVI D port on the I O panel connect a D Sub monitor cable to the D Sub port on the I O panel and connect a HDMI monitor cable to the HDMI port on the I O panel Then connect other monitor cables to the corresponding connectors of the add on PCI Express VGA cards on PCIE1 and PCIE2 slots 3 Boot your system Press lt F2 gt or lt Del gt to enter UEFI setup Enter Share Memory option to adjust the memory capability to 32MB 64MB 128MB 256MB or 512MB to enable the function of D sub Please make sure that the value you select is less than the total capability of the system memory If you do not adjust the UEFI setup the default value of Share Memory Auto will disable D Sub function when an add on VGA card is inserted to this motherboard 4 Install the onboard VGA driver and the add on PCI Express VGA card driver to your system If you have installed the drivers already there is no need to install them again 5 Set up a multi monitor display For Windows XP XP 64 bit OS Right click on desktop choose Properties and select the Settings tab so that you can adjust the parameters of the multi m
35. eeeseanessseeessaneess 48 3 4 1 CPU Configuration ssoi iieis 49 3 4 2 North Bridge Configuration ccccceceeeseeeeeees 51 3 4 3 South Bridge Configuration c ccccceesseeeeees 52 3 4 4 Storage Configuration ccccccccsseeseeeeeeeseeeeeees 59 3 4 5 Intel R Rapid Start Technology rrnrrrrvrvrrrnrrr 54 3 4 6 Intel R Smart Connect Technology 006 55 34 7 Super lO Configuration s v svrsnvasnsberminssie 56 3 4 8 ACPI Configuration rrrrrnrrrnnrnnvrvvrrnnernvrnnrrnnsrn 57 3 4 9 USB Conigur hon uovjurseketee jv 58 3 5 Hardware Health Event Monitoring Screen 59 DP NN 60 3 7 Security SAEENuu rvsesseesiieene dd rbnidtag 61 309 PU SEN 62 4 Software SUPPOTST cecseceeseeeeseceeseeeeeeeeeseteeennens 63 4 1 Install Operating System rrrrrrrrrnnnnnrrrrnnnnvnrnnnnnnnnnnnr 63 4 2 Support CD Information uujenvarvassssnmsmsisaivsssariansaniee 63 4 2 1 Running Support CD 4asersmsimsntsnemtabuses 63 4 2 2 Drivers Menu r rurnararernnernnnrrernnernnnennvenerrnnenneeneee 63 4 2 3 Utilities MENN uusssdardsmmssreendeds msmetrtsdn 63 4 2 4 Contact Information 63 Thank you for purchasing ASRock H77M motherboard a reliable motherboard produced under ASRock s consistently stringent quality control It delivers excellent performance with robust design conforming to ASRock s commitment to quality and endurance In this manual chapter 1 and
36. el s suggestion the EuP ready power supply must meet the standard of 5v and the standby power efficiency should be higher than 50 under 100 mA current consumption For EuP ready power sup ply selection we recommend you to check with the power supply manu facturer for more details 12 1 3 Motherboard Layout a Bh ON 1 2 3 4 5 21 6cm 8 5 in l Designed in Taipei JS 7 z unas EE 5 B USB3 SJ T st glll amp als S USB 3 0 A 6 ee lt x ejje 32 zll lt T USBA Top amp amp B USB5 RJ 4 A A 31 z EE 7 BEE HE a MSRock PCI Express 3 0 ai NE Al 30 vade Dar na 10 29 PEIET Roms Front USB3 0 X rast USB 13 s 7 PCI 27 Xrastram XFastLan Intel H77 64Mb PCI2 BIOS 14 26 ErP EuP Ready H77M 15 PCIE2 we a le y Bs t 25 24 23 22 21 20 19 18 17 16 ATX 12V Power Connector ATX12V1 18 Clear CMOS Jumper CLRCMOS1 CPU Fan Connector CPU_FAN1 19 USB 2 0 Header USB6_7 Black CPU Fan Connector CPU_FAN2 20 Consumer Infrared Module Header 1155 Pin CPU Socket CIR1 Gray 2 x 240 pin DDR3 DIMM Slots 21 USB 2 0 Header USB8_9 Black DDR3_A1 DDR3_B1 Black 22 Chassis Fan Connector CHA FAN1 ATX Power Connector ATXPWR1 23 Print Port Header LPT1 Black USB 3 0 Header USB3_0_1 Black 24
37. em with an Intel processor that sup ports Hyper Threading technology and an operating system that includes optimization for this technology such as Microsoft Windows XP Vista 7 is required Set to Enabled if using Microsoft Windows XP Vista 7 or Linux kernel version 2 4 18 or higher This option will be hidden if the installed CPU does not support Hyper Threading technology Active Processor Cores Use this item to select the number of cores to enable in each processor package The default value is All Enhance Halt State C1E All processors support the Halt State C1 The C1 state is supported through the native processor instructions HLT and MWAIT and requires no hardware support from the chipset In the C1 power state the processor maintains the context of the system caches CPU C3 State Support Use this to enable or disable CPU C3 ACPI C2 report to OS CPU C6 State Support Use this to enable or disable CPU C6 ACPI C3 report to OS Package C State Support Selected option will program into C State package limit register The default value is Auto CPU Thermal Throttling You may select Enabled to enable CPU internal thermal control mechanism to keep the CPU from overheating No Execute Memory Protection No Execution NX Memory Protection Technology is an enhancement 49 to the IA 32 Intel Architecture An IA 32 processor with No Execute NX Memory Protection can prevent data pages from being u
38. es Power On Use this item to enable or disable PCI devices to turn on the system from the power soft off mode Ring In Power On Use this item to enable or disable Ring In signals to turn on the system from the power soft off mode RTC Alarm Power On Use this item to enable or disable RTC Real Time Clock to power on the system USB Keyboard Remote Power On Use this item to enable or disable USB Keyboard Remote to turn on the system from the power soft off mode USB Mouse Power On Use this item to enable or disable USB Mouse to turn on the system from the power soft off mode 57 3 4 9 USB Configuration ASROCK UEFI SETUP UTILITY Security Exit Boot TE abcd Description erie Tomorrow s Technology Today USB 2 0 Controller Use this item to enable or disable the use of USB 2 0 controller USB 3 0 Controller Use this item to enable or disable the use of USB 3 0 controller Legacy USB Support Use this option to select legacy support for USB devices There are four configuration options Enabled Auto Disabled and UEFI Setup Only The default value is Enabled Please refer to below descriptions for the details of these four options Enabled Enables support for legacy USB Auto Enables legacy support if USB devices are connected Disabled USB devices are not allowed to use under legacy OS and UEFI setup when Disabled is selected If you have USB compatibility is sues it is recommended to select D
39. fits in one correct orientation It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation Step 3 Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated 20 2 6 Expansion Slots PCI and PCI Express Slots There are 2 PCI slots and 2 PCI Express slots on this motherboard PCI slots PCI slots are used to install expansion cards that have the 32 bit PCI interface PCIE slots PCIE1 PCIE 3 0 x16 slot is used for PCI Express x16 lane width graphics cards or to install PCI Express graphics cards to support CrossFireX function PCIE2 PCIE 2 0 x16 slot is used for PCI Express x4 lane width graph ics cards or to install PCI Express graphics cards to support CrossFi reX function 1 In single VGA card mode it is recommended to install a PCI Express x16 graphics card on PCIE1 slot In CrossFireX mode please install the PCI Express x16 graphics cards on PCIE1 and PCIE2 slots Therefore PCIE 1 will work at x16 bandwidth while PCIE2 works at x4 bandwidth Please connect a chassis fan to the motherboard s chassis fan connector CHA FAN1 or CHA FAN2 when using multiple graphics cards for better thermal environment 4 Only PCIE1 slot supports Gen 3 speed To run the PCI Express in Gen 3 speed please install an Ivy Bridge CPU If you install a Sandy Bridge CPU the PCI Expre
40. he DVI to D Sub adapter to convert the DVI connector to D Sub interface and then connect the D Sub monitor cable to the DVI to D Sub adapter 23 2 2 Driver Installation and Setup Step 1 Step 2 A Step 3 Step 4 Step 5 Step 6 Power on your computer and boot into OS Remove the AMD drivers if you have any VGA drivers installed in your system The Catalyst Uninstaller is an optional download We recommend using this utility to uninstall any previously installed Catalyst drivers prior to installation Please check AMD s website for AMD driver updates Install the required drivers to your system For Windows XP OS A AMD recommends Windows XP Service Pack 2 or higher to be installed If you have Windows XP Service Pack 2 or higher installed in your system there is no need to download it again http www microsoft com windowsxp sp2 default mspx B You must have Microsoft NET Framework installed prior to downloading and installing the CATALYST Control Center Please check Microsoft s website for details For Windows 7 Vista OS Install the CATALYST Control Center Please check AMD s website for de tails Restart your computer Install the VGA card drivers to your system and restart your computer You will find AMD Catalyst Control Center on your Windows taskbar A 44 10 54 AM AMD Catalyst Control Center Double click ATI Catalyst Control Center Click View sele
41. he illustration shows how jumpers are setup When the jumper cap is placed on pins the jumper is Short If no jumper cap V I is placed on pins the jumper is Open The illustration shows a 3 pin jumper whose iy g pin1 and pin2 are Short when jumper cap Short Open is placed on these 2 pins Jumper Setting Description Clear CMOS Jumper 12 2 3 psi ou oom see p 13 No 18 Default Clear CMOS Note CLRCMOS1 allows you to clear the data in CMOS To clear and reset the system parameters to default setup please turn off the computer and unplug the power cord from the power supply After waiting for 15 seconds use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds However please do not clear the CMOS right after you update the BIOS If you need to clear the CMOS when you just finish updating the BIOS you must boot up the system first and then shut it down before you do the clear CMOS ac tion Please be noted that the password date time user default profile 1394 GUID and MAC address will be cleared only if the CMOS battery is removed 30 2 11 Onboard Headers and Connectors A Onboard headers and connectors are NOT jumpers Do NOT place jumper caps over these headers and connectors Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard Serial ATA2 Connectors SATA2 2 see p 13 No 10 LO i SATA2_3 see p 13 No 11 al ai Sji IE
42. he type of speaker you use TABLE for Audio Output Connection 14 To enable Multi Streaming function you need to connect a front panel audio cable to the front panel audio header After restarting your computer you will find Mixer tool on your system Please select Mixer ToolBox amp click Enable playback multi streaming and click ok Choose 2CH 4CH 6CH or 8CH and then you are allowed to select Realtek HDA Primary output to use Rear Speaker Central Bass and Front Speaker or select Realtek HDA Audio 2nd output to use front panel audio 15 Chapter 2 Installation This is a Micro ATX form factor 9 6 x 8 5 24 4 x 21 6 cm motherboard Before you install the motherboard study the configuration of your chassis to ensure that the motherboard fits into it Make sure to unplug the power cord before installing or removing the motherboard Failure to do so may cause physical injuries to you and damages to motherboard components 2 1 Screw Holes Place screws into the holes indicated by circles to secure the motherboard to the chassis 4 Do not over tighten the screws Doing so may damage the motherboard 2 2 Pre installation Precautions Take note of the following precautions before you install motherboard components or change any motherboard settings 1 Unplug the power cord from the wall socket before touching any components 2 To avoid damaging the
43. ide to install OS If you install Windows 7 64 bit Vista 64 bit on a large hard disk ex Disk volume gt 2TB it may take more time to boot into Windows or install driver utilities If you encounter this problem you will need to follow the instructions below to fix this problem Windows Vista 64 bit Microsoft does not provide hotfix for this problem The steps listed below are Microsoft s suggested solution A Disable System Restore a Type systempropertiesprotection in the Start Menu Then press Enter 182 systempropertiesprotection Control Panel Default Programs Help and Support s b De select Local Disks for System Restore Then Click Turn System Restore Off to confirm Then Press OK 66 System Properties Computer Name Hardware Advanced System Protection Remote You can use restore points to undo unwanted system changes How much disk space is required You can also use restore points to restore previous versions of files called shadow copies How do use previous versions System Restore System Restore helps you restore your computer s system files to an earlier point in time Automatic restore points Create restore points automatically on the selected disks stable Disks Local Disk C System Local Disk D Most recent restore point 2 14 2011 3 59 20 AM None System Protection You can create a restore poi Rest
44. isabled to enter OS UEFI Setup Only USB devices are allowed to use only under UEFI setup and Windows Linux OS Legacy USB 3 0 Support Use this option to enable or disable legacy support for USB 3 0 devices The default value is Enabled 58 3 5 Hardware Health Event Monitoring Screen In this section it allows you to monitor the status of the hardware on your system including the parameters of the CPU temperature motherboard temperature CPU fan speed chassis fan speed and the critical voltage ASROCK UEFI SETUP UTILITY CPU Fan 1 amp 2 Setting This allows you to set CPU fan 1 amp 2 s speed Configuration options Full On and Automatic Mode The default value is Full On Chassis Fan 1 Setting This allows you to set chassis fan 1 s speed Configuration options Full On Automatic Mode and Manual The default value is Full On Chassis Fan 2 Setting This allows you to set chassis fan 2 s speed Configuration options Full On and Manual The default value is Full On Over Temperature Protection Use this to enable or disable Over Temperature Protection The default value is Enabled 59 3 6 Boot Screen In this section it will display the available devices on your system for you to config ure the boot settings and the boot priority ASROCK UEFI SETUP UTILITY Tomorrow s Technology Today Setup Prompt Timeout This shows the number of seconds to wait for setup activation key 65
45. lect this option the following message Discard changes and exit setup will pop out Select Yes to exit the UEFI SETUP UTILITY without saving any changes Discard Changes When you select this option the following message Discard changes will pop out Select Yes to discard all changes Load UEFI Defaults Load UEFI default values for all the setup questions F9 key can be used for this operation Launch EFI Shell from filesystem device Attempts to Launch EFI Shell application Shell64 efi from one of the available filesystem devices 62 Chapter 4 Software Support 4 1 Install Operating System This motherboard supports various Microsoft Windows operating systems 7 7 64 bit Vista Vista 64 bit XP XP 64 bit Because motherboard settings and hardware options vary use the setup procedures in this chapter for general refer ence only Refer to your OS documentation for more information 4 2 Support CD Information The Support CD that came with the motherboard contains necessary drivers and useful utilities that enhance the motherboard s features 4 2 1 Running The Support CD To begin using the support CD insert the CD into your CD ROM drive The CD automatically displays the Main Menu if AUTORUN is enabled in your computer If the Main Menu does not appear automatically locate and double click on the file ASSETUP EXE from the BIN folder in the Support CD to dis play the menu 4 2 2
46. lity of such damages arising from any defect or error in the manual or product EG This device complies with Part 15 of the FCC Rules Operation is subject to the fol lowing two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CALIFORNIA USA ONLY The Lithium battery adopted on this motherboard contains Perchlorate a toxic substance controlled in Perchlorate Best Management Practices BMP regulations passed by the California Legislature When you discard the Lithium battery in Cali fornia USA please follow the related regulations in advance Perchlorate Material special handling may apply see www dtsc ca gov hazardouswaste perchlorate ASRock Website http www asrock com Contents MON 7 1 1 Package Contents vuyeesansmemeunnaienaiieeeen ates 7 12 SEAN 8 1 3 Motherboard Layout rrrrnnnernnnnnnovnnnnnnevnnnennnnnnnnnnnnnnenr 13 ta OPP soiis ocamancoactnene ss EEA 14 2 ASTON Ms EE bandana caaaneee 16 2 1 STN Eve 16 2 2 Pre installation Precautions rrrrnnrrnnnnrrrnnnennnnnnnnnnre 16 25 CPU Installation svada 17 2 4 Installation of Heatsink and CPU fan 19 2 5 Installation of Memory Modules DIMM 0008 20 2 6 Expansion Slots PCI and PCI Express Slots 008 21 2 7 CrossFirex and Quad CrossFireX Operation Guide 22 2 8 Dual Monitor and S
47. ll guide you to install the SATA SATA2 hard disks STEP 1 Install the SATA SATA2 hard disks into the drive bays of your chassis STEP 2 Connect the SATA power cable to the SATA SATA2 hard disk STEP 3 Connect one end of the SATA data cable to the motherboard s SATA2 con nector STEP 4 Connect the other end of the SATA data cable to the SATA SATA2 hard disk 2 13 Serial ATA3 SATA3 Hard Disks Installation This motherboard adopts Intel H77 chipset that supports Serial ATA3 SATA3 hard disks and RAID RAID 0 RAID 1 RAID 5 RAID 10 Intel Rapid Storage and Intel Smart Response Technology functions You may install SATA3 hard disks on this motherboard for internal storage devices This section will guide you to install the SATA3 hard disks STEP 1 Install the SATA3 hard disks into the drive bays of your chassis STEP 2 Connect the SATA power cable to the SATA3 hard disk STEP 3 Connect one end of the SATA data cable to the motherboard s SATA3 con nector STEP 4 Connect the other end of the SATA data cable to the SATA3 hard disk 36 2 14 Hot Plug and Hot Swap Functions for SATA SATA2 HDDs This motherboard supports Hot Plug and Hot Swap functions for SATA SATA2 in RAID AHCI mode Intel H77 chipset provides hardware support for Advanced Host controller Interface AHCI a new programming interface for SATA host controllers developed through a joint industry effort A NOTE What is Hot Plug Function
48. logy allows users to enjoy the great audio experience from the portable audio devices such like MP3 player or mobile phone to your PC even when the PC is turned off or in ACPI S5 mode This motherboard also provides a free 3 5mm audio cable op tional that ensures users the most convenient computing environment While CPU overheat is detected the system will automatically shutdown Before you resume the system please check if the CPU fan on the moth erboard functions properly and unplug the power cord then plug it back again To improve heat dissipation remember to spray thermal grease between the CPU and the heatsink when you install the PC system Combo Cooler Option C C O provides the flexible option to adopt three different CPU cooler types Socket LGA 775 LGA 1155 and LGA 1156 Please be noticed that not all the 775 and 1156 CPU Fan can be used 11 20 ASRock XFast RAM is not supported by Microsoft Windows XP XP 21 64 bit Intel Smart Connect Technology and Intel USB 3 0 ports are not supported by Microsoft Windows Vista Vista 64 bit XP XP 64 bit EuP stands for Energy Using Product was a provision regulated by the European Union to define the power consumption for the completed system According to EuP the total AC power of the completed system should be under 1 00W in off mode condition To meet EuP standards an EuP ready motherboard and an EuP ready power supply are required According to Int
49. nitor Boot Enabled Description __ errs T Tomorrow s Technology Today SATA Controller s Use this item to enable or disable the SATA Controller feature SATA Mode Selection Use this to select SATA mode Configuration options IDE Mode AHCI Mode and RAID Mode The default value is AHCI Mode new features that will improve SATA disk performance but IDE mode does not have these advantages A AHCI Advanced Host Controller Interface supports NCQ and other Aggressive Link Power Management Use this item to configure Aggressive Link Power Management Hard Disk S M A R T Use this item to enable or disable the S M A R T Self Monitoring Analy sis and Reporting Technology feature Configuration options Disabled and Enabled 53 3 4 5 Intel R Rapid Start Technology ASROCK UEFI SETUP UTILITY O_o JE Security Exit Boot Intel R Rapid Start Technology Disabled x Description Tomorrow s Technology Today Intel R Rapid Start Technology Use this item to enable or disable Intel R Rapid Start Technology Intel R Rapid Start Technology is a new zero power hibernation mode which al lows users to resume in just 5 6 seconds The default is Disabled 54 3 4 6 Intel R Smart Connect Technology ASROCK UEFI SETUP UTILITY Security Exit Boot Description Tomorrow s Technology Today Intel R Smart Connect Technology Use this item to enable or disable Intel R Smart Connect Technology
50. oling fan compliant with Intel 1155 Pin CPU to dissipate heat Before you install the heatsink you need to spray ther mal interface material between the CPU and the heatsink to improve heat dissipa tion Ensure that the CPU and the heatsink are securely fastened and in good con tact with each other Then connect the CPU fan to the CPU FAN connector CPU _ FAN1 see page 13 No 2 or CPU FAN2 see page 13 No 3 For proper installation please kindly refer to the instruction manuals of your CPU fan and heatsink Below is an example to illustrate the installation of the heatsink for 1155 Pin CPUs Step 1 Apply thermal interface material onto the cen ter of the IHS on the socket s surface Step 2 Place the heatsink onto the socket Ensure that the fan cables are oriented on side closest to the CPU fan connector on the motherboard CPU FAN1 see page 13 No 2 or CPU FAN2 see page 13 No 3 Step 3 Align fasteners with the motherboard through holes Step 4 Rotate the fastener clockwise then press down on fastener caps with thumb to install hi yy Press Down Y ER MN and lock Repeat with remaining fasteners If you press down the fasteners without rotating them clockwise the heatsink cannot be secured on the motherboard Step 5 Connect fan header with the CPU fan connector on the motherboard Step 6 Secure redundant cable with tie wrap to ensure the cable does not interfere with fan operation or contact other
51. onitors according to the steps below A Click the Identify button to display a large number on each monitor B Right click the display icon in the Display Properties dialog that you wish to be your primary monitor and then select Primary When you use multiple monitors with your card one monitor will always be Primary and all additional monitors will be designated as Secondary C Select the display icon identified by the number 2 D Click Extend my Windows desktop onto this monitor E Right click the display icon and select Attached if necessary F Set the appropriate Screen Resolution and Color Quality for the second monitor Click Apply or OK to apply these new values G Repeat steps C through E for the display icon identified by the numbers three to six 27 For Windows 7 7 64 bit Vista Vista 64 bit OS Right click the desktop choose Personalize and select the Display Settings tab so that you can adjust the parameters of the multi monitors according to the steps below A Click the number 2 icon B Click the items This is my main monitor and Extend the desktop onto this monitor C Click OK to save your change D Repeat steps A through C for the display icons identified by the number three to six 6 Use Surround Display Click and drag the display icons to positions representing the physical setup of your monitors
52. oper installation 3 Due to the operating system limitation the actual memory size may be less than 4GB for the reservation for system usage under Windows 7 Vista XP For Windows OS with 64 bit CPU there is no such limita tion You can use ASRock XFast RAM to utilize the memory that Win dows cannot use 4 Only PCIE1 slot supports Gen 3 speed To run the PCI Express in Gen 3 speed please install an Ivy Bridge CPU If you install a Sandy Bridge CPU the PCI Express will run only at PCI Express Gen 2 speed 5 The maximum shared memory size is defined by the chipset vendor and is subject to change Please check Intel website for the latest informa tion 6 You can choose to use two of the three monitors only D Sub DVI D and HDMI monitors cannot be enabled at the same time Besides with the DVI to HDMI adapter the DVI D port can support the same features as HDMI port 10 Iil xvYCC and Deep Color are only supported under Windows 7 64 bit 7 Deep Color mode will be enabled only if the display supports 12bpc in EDID HBR is supported under Windows 7 64 bit 7 Vista 64 bit Vista For microphone input this motherboard supports both stereo and mono modes For audio output this motherboard supports 2 channel 4 chan nel 6 channel and 8 channel modes Please check the table on page 14 for proper connection ASRock Extreme Tuning Utility AXTU is an all in one tool to ne tune dif ferent system func
53. or Windows 7 7 64 bit Vista Vista 64 bit OS Go to the FrontMic Tab in the Realtek Control panel Adjust Recording Volume Header PLED This header accommodates mr several system front panel functions DUMMY RESET GND HDLED HDLED Connect the power switch reset switch and system status indicator on the chassis to this header according to the pin assignments below Note the positive and negative pins before connecting the cables PWRBTN Power Switch Connect to the power switch on the chassis front panel You may configure the way to turn off your system using the power switch RESET Reset Switch Connect to the reset switch on the chassis front panel Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart PLED System Power LED Connect to the power status indicator on the chassis front panel The LED is on when the system is operating The LED keeps blinking when the sys tem is in S1 S3 sleep state The LED is off when the system is in S4 sleep state or powered off S5 HDLED Hard Drive Activity LED Connect to the hard drive activity LED on the chassis front panel The LED is on when the hard drive is reading or writing data The front panel design may differ by chassis A front panel module mainly consists of power switch reset switch power LED hard drive activity LED speaker and etc When connecting your chassis front
54. ore off disks selected above Are you sure you want to turn System All existing restore points on the disk will be deleted and no new ones will be created Turn System Restore Off B Disable Volume Shadow Copy service a Type computer management in the Start Menu then press Enter Programs amp Computer Management gt Search Everywhere Search the Internet Documents Pictures Music Games Recent Items Computer Network Connect To ntrol Panel Default Programs Help and Support 2 b Go to Services and Applications gt Services Then double click Volume 33 Shadow Copy a TETE File Action View Help e9 200E i 2 Computer Management Local Actions a System Tools Services a Task Scheduler aa a H eRe Volume Shadow Copy Name Description Status Startup Type Log Oi More Actions 3 Smart Card Removal Po Allows thes Manual Local a shared Folders Stop the service SNMP Tra Receives tra Manual Local VEEE SR SS Local Users and Groups Restart the service 2 cg j More Software Licensing Enables the Started Automatic Netwo ORE COTS Reliability and Performa z SSDP Discovery Discovers n Started Manual Local aa Device Manager EE Br DE 7 Description i Superfetch Maintains a Started Automatic Local en Ken and a OL aT System Event Notificati Monitors sy Started Automatic Local fey
55. ormance The performance may depend on the properties of the device ASRock XFast LAN provides a faster internet access which includes the benefits listed below LAN Application Prioritization You can config ure your application s priority ideally and or add new programs Lower Latency in Game After setting online game s priority higher it can lower the latency in games Traffic Shaping You can watch Youtube HD videos and download simultaneously Real Time Analysis of Your Data With the status window you can easily recognize which data streams you are transferring currently ASRock XFast RAM is a new function that is included into ASRock Ex treme Tuning Utility AXTU It fully utilizes the memory space that cannot be used under Windows OS 32 bit CPU ASRock XFast RAM shortens the loading time of previously visited websites making web surfing faster than ever And it also boosts the speed of Adobe Photoshop 5 times faster Another advantage of ASRock XFast RAM is that it reduces the frequency of accessing your SSDs or HDDs in order to extend their lifes pan ASRock Crashless BIOS allows users to update their BIOS without fear of failing If power loss occurs during the BIOS update process ASRock Crashless BIOS will automatically finish the BIOS update procedure after regaining power Please note that BIOS files need to be placed in the root directory of your USB disk Only USB2 0 ports support this feature ASRock On Off Play Techno
56. ration Intel Core i7 i5 i3 in LGA1155 Package Digi Power Design 4 2 Power Phase Design Supports Intel Turbo Boost 2 0 Technology Supports Intel K Series unlocked CPU Supports Hyper Threading Technology see CAUTION 1 Supports Intel Rapid Start Technology and Smart Connect Technology with Intel Ivy Bridge CPU Dual Channel DDR3 Memory Technology see CAUTION 2 2 x DDR3 DIMM slots Supports DDR3 1600 1333 1066 non ECC un buffered memory DDR3 1600 with Intel Ivy Bridge CPU DDR3 1333 with Intel Sandy Bridge CPU Max capacity of system memory 16GB see CAUTION 3 Supports Intel Extreme Memory Profile XMP 1 3 1 2 Expansion Slot 1x PCI Express 3 0 x16 slot PCIE1 x16 mode see CAUTION 4 PCIE 3 0 is only supported with Intel Ivy Bridge CPU With Intel Sandy Bridge CPU it only supports PCIE 2 0 1x PCI Express 2 0 x16 slot PCIE2 x4 mode 2 x PCI slots Supports AMD Quad CrossFireX and CrossFirex Intel HD Graphics Built in Visuals and the VGA outputs can be supported only with processors which are GPU integrated Supports Intel HD Graphics Built in Visuals Intel Quick Sync Video Intel InTru 3D Intel Clear Video HD Technology Intel Insider Intel HD Graphics 2500 4000 Intel Advanced Vector Extensions AVX Pixel Shader 5 0 DirectX 11 with Intel Ivy Bridge CPU Pixel Shader 4 1 DirectX 10 1 with Intel Sandy Bridge CPU
57. rive or hard drive must use FAT32 16 12 file system If you desire a faster less restricted way of charging your Apple devices such as iPhone iPad iPod Touch ASRock has prepared a wonderful so lution for you ASRock APP Charger Simply install the APP Charger driver it makes your iPhone charge much quickly from your computer and up to 40 faster than before ASRock APP Charger allows you to quickly charge many Apple devices simultaneously and even supports continuous charging when your PC enters into Standby mode S1 Sus pend to RAM S3 hibernation mode S4 or power off S5 With APP Charger driver installed you can easily enjoy the marvelous charging experience ASRock website http Awww asrock com Feature AppCharger index asp 10 2 13 14 15 16 de 18 19 ASRock SmartView a new function for internet browsers is the smart start page for IE that combines your most visited web sites your history your Facebook friends and your real time newsfeed into an enhanced view for a more personal Internet experience ASRock motherboards are exclusively equipped with the ASRock SmartView utility that helps you keep in touch with friends on the go To use ASRock SmartView feature please make sure your OS version is Windows 7 7 64 bit Vista Vista 64 bit and your browser version is IE8 ASRock website http www asrock com Feature SmartView index asp ASRock XFast USB can boost USB storage device perf
58. sed by malicious software to execute codes This option will be hidden if the current CPU does not support No Excute Memory Protection Intel Virtualization Technology When this option is set to Enabled a VMM Virtual Machine Architecture can utilize the additional hardware capabilities provided by Vanderpool Technology This option will be hidden if the installed CPU does not support Intel Virtualization Technology Hardware Prefetcher Use this item to turn on off the MLC streamer prefetcher Adjacent Cache Line Prefetch Use this item to turn on off prefetching of adjacent cache lines 50 3 4 2 North Bridge Configuration ASROCK UEFI SETUP UTILITY Primary Graphics Adapter This allows you to select Onboard PCI or PCI Express as the boot graphic adapter priority The default value is PCI Express VT d Use this to enable or disable Intel VT d technology Intel Virtualization Technology for Directed I O The default value of this feature is Disabled Share Memory This allows you to set onboard VGA share memory feature The default value is Auto IGPU Multi Moniter This allows you to enable or disable IGPU Multi Moniter The default value is Enabled If you install the PCI Express card under Windows XP Vista OS please disable this option Render Standby Use this to enable or disable Render Standby by Internal Graphics Device The default value is Enabled Deep Render Standby Use this to enable
59. ss will run only at PCI Express Gen 2 speed N D Installing an expansion card Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Before installing an expansion card please make sure that the power supply is switched off or the power cord is unplugged Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation Remove the system unit cover if your motherboard is already installed in a chassis Remove the bracket facing the slot that you intend to use Keep the screws for later use Align the card connector with the slot and press firmly until the card is completely seated on the slot Fasten the card to the chassis with screws Replace the system cover 21 2 7 CrossFireX and Quad CrossFirex Operation Guide This motherboard supports CrossFirex and Quad CrossFirex CrossFirex technology offers the most advantageous means available of combining multiple high performance Graphics Processing Units GPU in a single PC Combining a range of different operating modes with intelligent software design and an innovative interconnect mechanism CrossFireX enables the highest possible level of performance and image quality in any 3D application Currently CrossFirex is supported by Windows XP with Service Pack 2 Vista 7 OS Quad CrossFirex is supported by Windows Vista 7 OS only Please check AMD s website for AMD
60. support USB 1 0 2 0 3 0 up to 5Gb s 1 x Front USB 3 0 header supports 2 USB 3 0 ports supports USB 1 0 2 0 3 0 up to 5Gb s Connector 4 x SATA2 3 0 Gb s connectors support RAID RAID 0 RAID 1 RAID 5 RAID 10 Intel Rapid Storage and Intel Smart Response Technology NCQ AHCI and Hot Plug functions 2 x SATA3 6 0Gb s connectors 1x IR header 1 x CIR header 1 x Print Port header 1 x COM port header 1x HDMI SPDIF header CPU Chassis Power FAN connector 24 pin ATX power connector 8 pin 12V power connector Front panel audio connector 2 x USB 2 0 headers support 4 USB 2 0 ports 1 x USB 3 0 header supports 2 USB 3 0 ports BIOS Feature 64Mb AMI UEFI Legal BIOS with GUI support Supports Plug and Play ACPI 1 1 Compliance Wake Up Events Supports jumperfree SMBIOS 2 3 1 Support CPU Core IGPU DRAM 1 8V PLL VTT VCCSA Voltage Multi adjustment Support CD Drivers Utilities AntiVirus Software Trial Version CyberLink MediaEspresso 6 5 Trial ASRock MAGIX Multimedia Suite OEM Unique Feature ASRock Extreme Tuning Utility AXTU see CAUTION 9 ASRock Instant Boot ASRock Instant Flash see CAUTION 10 ASRock APP Charger see CAUTION 11 ASRock SmartView see CAUTION 12 ASRock XFast USB see CAUTION 13 ASRock XFast LAN see CAUTION 14 ASRock XFast RAM see CAUTION 15 ASRock Crashless BIOS see CAUTION 16 ASRock On Off Play Technology see CAUT
61. that you would like to use The placement of display icons determines how you move items from one monitor to another HDCP Function HDCP function is supported on this motherboard To use HDCP function with this motherboard you need to adopt a monitor that supports HDCP function as well Therefore you can enjoy the superior display quality with high definition HDCP encryption contents Please refer to the instructions below for more details about HDCP function What is HDCP HDCP stands for High Bandwidth Digital Content Protection a specification developed by Intel for protecting digital entertainment content that uses the DVI interface HDCP is a copy protection scheme to eliminate the possibility of intercepting digital data midstream between the video source or transmitter such as a computer DVD player or set top box and the digital display or receiver such as a monitor television or projector In other words HDCP specification is designed to protect the integrity of content as it is being transmitted Products compatible with the HDCP scheme such as DVD players satellite and cable HDTV set top boxes as well as few entertainment PCs requires a secure connection to a compliant display Due to the increase in manufacturers employing HDCP in their equipment it is highly recommended that the HDTV or LCD monitor you purchase is compatible 28 2 9 ASRock Smart Remote Installation Guide ASRock Smart Remote is only used
62. tions in a user friendly interface which includes Hard ware Monitor Fan Control Overclocking OC DNA and IES In Hardware Monitor it shows the major readings of your system In Fan Control it shows the fan speed and temperature for you to adjust In Overclocking you are allowed to overclock CPU frequency for optimal system per formance In OC DNA you can save your OC settings as a profile and share it with your friends Your friends then can load the OC profile to their own system to get the same OC settings In IES Intelligent Energy Saver the voltage regulator can reduce the number of output phases to improve efficiency when the CPU cores are idle without sacrificing computing performance Please visit our website for the operation proce dures of ASRock Extreme Tuning Utility AXTU ASRock website http Awww asrock com ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM This convenient BIOS update tool allows you to update system BIOS without entering operating systems first like MS DOS or Windows With this utility you can press the lt F6 gt key during the POST or the lt F2 gt key to enter into the BIOS setup menu to access ASRock Instant Flash Just launch this tool and save the new BIOS file to your USB flash drive floppy disk or hard drive then you can update your BIOS only in a few clicks without preparing an additional floppy diskette or other complicated flash utility Please be noted that the USB flash d
63. uration options Auto Default Profile 1 and Profile 2 The default value is Auto DRAM Frequency If Auto is selected the motherboard will detect the memory module s inserted and assign the appropriate frequency automatically DRAM Timing Control ASROCK UEFI SETUP UTILITY Tomorrow s Technology Today DRAM tCL Use this item to change CAS Latency tCL Auto Manual setting The default is Auto DRAM tRCD Use this item to change RAS to CAS Delay tRCD Auto Manual setting The default is Auto 45 DRAM tRP Use this item to change Row Precharge Time tRP Auto Manual setting The default is Auto DRAM tRAS Use this item to change RASf Active Time tRAS Auto Manual setting The default is Auto Command Rate CR Use this item to change Command Rate CR Auto Manual setting The default is Auto DRAM tWR Use this item to change Write Recovery Time tWR Auto Manual setting The default is Auto DRAM tRFC Use this item to change Refresh Cyle Time tRFC Auto Manual setting The default is Auto DRAM tRRD Use this item to change RAS to RAS Delay tRRD Auto Manual setting The default is Auto DRAM tWTR Use this item to change Write to Read Delay tWTR Auto Manual setting The default is Auto DRAM tRTP Use this item to change Read to Precharge tRTP Auto Manual setting The default is Auto DRAM tFAW Use this item to change Four Activate Window tFAW Auto Manual set ting Th
64. urround Display Features 26 2 9 ASRock Smart Remote Installation Guide 29 2 10 Jumpers Setup saceicecstantcceavestecdaavtensainngenicsaczecceeseendes 30 2 11 Onboard Headers and Connectors cseeeeeeeeee eens 31 2 12 Serial ATA SATA Serial ATA2 SATA2 Hard Disks f SPELE EEE EN 36 2 13 Serial ATA3 SATA3 Hard Disks Installation 36 2 14 Hot Plug and Hot Swap Functions for SATA SATA2 POD JE EE nee eee 37 2 15 Hot Plug and Hot Swap Functions for SATA3 HDDs 37 2 16 SATA SATA2 SATA3 HDD Hot Plug Feature and Operation Guide avsendere 38 2 17 Driver Installation Guide mrrrrrnnnnnrrnnnnnrrnnnnnnrrnnnnennnnnn 40 2 18 Installing Windows 7 7 64 bit Vista Vista 64 bit With RAID Functions rrronrrnnnnnnnnnnrnnnnnrnnnsnnnnnn 40 2 19 Installing Windows 7 7 64 bit Vista Vista 64 bit XP XP 64 bit Without RAID Functions _ 41 2 19 1 Installing Windows XP XP 64 bit Without RAID FUNCIONS onnea aa 41 2 19 2 Installing Windows 7 7 64 bit Vista Vista 64 bit Without RAID Functions 41 S JEFI SETUP UTILITY n ste 42 TINN 42 3 1 1 UEFI Menu Bar siciiamcnsetentimniicacorenmntationinendivancess 42 312 Navigation KEYS ercsscirnsnssescnsnsnsossn 43 3 2 Main SEN ee 43 3 3 OC Tweaker Screen icc ccissicostatestuciceticassectecsinseteoionaees 44 3 4 Advanced SCIreeN cccccccccsesseeeeeceensee
65. us page lt PGDN gt Go to the next page lt HOME gt Go to the top of the screen lt END gt Go to the bottom of the screen lt F1 gt To display the General Help Screen lt F7 gt Discard changes and exit the UEFI SETUP UTILITY lt F9 gt Load optimal default values for all the settings lt F10 gt Save changes and exit the UEFI SETUP UTILITY lt F12 gt Print screen lt ESC gt Jump to the Exit Screen or exit the current screen 3 2 Main Screen When you enter the UEFI SETUP UTILITY the Main screen will appear and display the system overview ASROCK UEFI SETUP UTILITY H H Monitor Security Exit Boot Description Tomorrow s Technology Today System Browser System Browser can let you easily check your current system configuration in UEFI setup 43 3 3 OC Tweaker Screen In the OC Tweaker screen you can set up overclocking features ASROCK UEFI SETUP UTILITY Security Exit NS Boot CPU Configuration CPU Turbo Ratio Use this item to change the ratio value of this motherboard Intel SpeedStep Technology Intel SpeedStep technology is Intel s new power saving technology Pro cessors can switch between multiple frequencies and voltage points to en able power saving The default value is Enabled Configuration options Enabled and Disabled If you install Windows Vista 7 and want to enable this function please set this item to Enabled This item will be hid den if the current CPU

Download Pdf Manuals

Related Search

Related Contents

  水沢配水池（1号池）築造工事（電気設備） 特記仕様書 四日市市上  Ton patro  User ManUal - SweetPea Toy Company  Lincoln Electric 300D User's Manual  Flo-Tronic Plus™ - United Process Controls  e - Forms User Manual ( Deduction of old cancellation not posted in  Test Stand (Serv. Man. LN-9259-07)  The Original Pink Box PB18VCIR Use and Care Manual  Contents: - Sears PartsDirect  

Copyright © All rights reserved. Failed to retrieve file