CyberPower RMCARD302 remote power controller
Contents
1. SubnetMask 255 255 255 0 Address is 192 168 20 177 and Gateway 192 168 10 1 the default Subnet Mask is 255 255 255 0 Figure 2 The Device Network setting window 6 Modify the IP subnet mask Authentication or gateway address Enter the new addresses into the corresponding fields Enter the user name and password to save changes User name Password Figure 3 Authentication window 7 You will need to enter a User Name and Password for the Remote Management Card in the authentication window as shown in figure 3 Default user name cyber Default password cyber Network Settings Information Setup MAC 00 0C 15 04 04 04 OK Power Device Network Information 8 If IP address is successfully or 255 255 255 0 you will see a message that ete 192 168 101 the IP set up is OK as shown in figure 4 Figure 4 Setup IP Address successfully message Method 2 Using a command prompt 1 Obtain the MAC address from the label on the Remote Management Card Each Management Card has a unique MAC address 2 Use the ARP command to set the IP address Example To assign the IP Address 192 168 10 134 for the Remote Management Card which has a MAC address of 00 0C 15 0A 0A 0A you will type in the following command prompt from a PC connected to the same network as the Remote Management Card 1 Type in arp s 192 168 10 134 O0 0C 15 0A 0A 0A then press Enter 32. part in the user s manual Conformance Approvals FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does not cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device compiles with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTE THE MANUFACTURER IS N
3. CyberPower Reliability Quality Value QUICK INSTALLATION GUIDE Remote Management Card RMCARD302 Intelligent Remote Management Card allows a UPS system to be managed monitored and configured K09 0000057 01 INSTALLATION GUIDE Step 1 Hardware Installation 1 Turn off the UPS before removing the expansion port cover on the UPS 2 Remove the two retaining screws of the expansion port cover then remove the cover 3 Install the CyberPower Remote Management Card into the expansion port 4 Re install and tighten the retaining screws 5 Connect the Ethernet cable to the LAN port of the CyberPower Remote Management Card 6 Turn on the UPS LINK Indicator O CyberPower _ _ Ethernet connector RX TX Indicator RMCARD302 x Definitions for LED Indicators The Remote Management Card is not Off connected to the Network or the Remote Management Card power is OFF On Yellow The Remote Management Card is connected to the Network The Remote Management Card power is OFF On Green The Remote Management Card power is ON Flash Receiving transmitting data packet Reset finished Step 2 Configure the IP address for the CyberPower Remote Management Card Method 1 Using the Power Device Network Util
4. Use the Ping command to assign a size of 123 bytes to the IP 1 Type in ping 192 168 10 134 I 123 then press Enter 2 If the replies are received your computer can communicate with the IP address WEB INTERFACE Login Account There are two user account types Administrator default username cyber default password cyber Viewer default username device default password cyber The administrator can access full functions including enable disable the Viewer account and the viewer can access the read function but can not control or change any setting Trouble Shooting Problem Solution O O Unable to configure 1 Check the LED status the normal condition the Remote is both yellow and green led are on Management Card If green led is off by method 1 or gt Check if the Remote Management Card is method 2 properly seated in the UPS and the UPS power is on If yellow led is off gt Check if the network connection is valid 2 Check if the operated PC is on the same physical network as Remote Management Card is Unable to ping the Remote Management Card Use method1 and method2 to get correct IP address of the Remote Management Card If the operated PC is on the different physical network from the Remote Management Card verify the setting of subnet mask and the IP address of gateway Lost the user name and password Please refer to the Reset to Default Setting Recover from a Lost Password
5. OT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED TO THIS EQUIPMENT SUCH MODIFICATIONS COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT CyberPower North America CyberPower Systems USA Inc Phone 952 403 9500 Toll free 877 297 6937 4241 12th Avenue E Suite 400 Shakopee MN 55379 E mail tech cpsww com Website www CPSww com CyebrPower Europe CyberPower Systems Inc E mail sales cpsww eu Website www cpsww eu CyberPower Systems France Z Saint S verin 28220 CLOYES sur le Loir France T l 33 0 2 37 98 61 50 E mail sales cpsww com fr
6. ity Tool 1 Install the Power Device Network Utility Tool from the included CD It is located on the CD in the tools nework folder Double click the Power Device Network Utility installation file Setup msi to begin the installation 2 After installation is completed run the Power Device Network Utility program Under All Programs select CyberPower Power Device Network Utility 3 The main dialog of the Power Device Network Utility Tool program is shown in Figure 1 The tool will display all Remote Management Cards present on the network The Refresh button is used to search the entire local network again Z Power Device Network Utility File Tools Help Power Devices MAC Address IP Address Subnet Mask Gateway DHCP Name Eg 00 0C 15 0A 0A 0A 192 168 20 177 255 255 255 0 192 168 20 1 Enable RMCARD302 TETITITITITITITIITIIIITITI ITLL Figure 1 The main window of the Power Device Network Utility program 4 Select the Remote Management Card you are setting up Click on the Tools menu and select Device Setup or double click the Remote Management Card you want to configure Device Network Settings 5 You can modify the IP Address Subnet Mask and Gateway address for the Device MAC Address listed in the Device Network Settings window as shown in figure 2 The default IP Device MAC Address 00 0C 15 0A 0A 0A Using DHCP OYes No IP Address 192 168 10 134
Download Pdf Manuals
Related Search