Nissin Di866 Mark II
Contents
1. At Remote flash mode Di866 Mark II is set automatically for manual zoom setting and its reflector position is set for 24mm to cover the wider range of illumination It is possible to set the desired flash coverage angle manually by select button 4 gt Place the slave flash in consideration to 1 The slave flash does not shoot its light directly into the camera lens 2 The wireless flash sensor of the slave flash is not blocked 3 The slave flash is usually not placed behind the master flash 4 In the daylight synchronization the sensor of slave flash could be saturated by sunlight and its response will be extremely reduced In this case the wireless TTL function may not result in success Making a shade to cover the sensor of slave flash is one of the ideas to help the situation Where is the Slave flash sensor Slave flash sensor is provided behind the front panel of Di866 Mark II at the name of Nissin DIGITAL The sensor s sensing angle to respond to the incoming light is about 100 degree 26 Setting the Master flash The modes available on the Master flash are TTL and M mode The master flash sets the signal transmission channel flash reflector zooming position flash mode of the master flash itself and flash mode and value adjustment of the slave flash at A B and C respectively Inthe main page Select Wireless mode WIRELESS A TL Inthe Wireless page Select M Master mode Wireless Mast2. 3 3 5 4 4 5 5 5 5 1 22000 TROUBLE SHOOTING The flash unit does not start charging Batteries are not correctly installed gt gt gt Install batteries to correct direction Batteries are exhausted gt gt gt Replace the batteries if the recycle time is beyond 20 The flash unit does not flash The flash unit is not firmly clipped on the camera gt gt gt Mount the flash unit firmly on the camera s hot shoe The flash unit is automatically powered off gt gt gt Turn on the switch again The flash picture is overexposed or underexposed gt gt gt Use FE lock The unit is set for manual exposure mode at wrong distance gt gt gt Set to TTL mode or select other power level There is a reflective object or strong lighting near the subject 39 WARRANTY In case of the following reasons of the defect it may void the warranty Please refer to the respective warrantee condition for details which varies from different countries 1 The product is not used in accordance with the instruction of the owner s manual 2 The product is repaired or modified by the one who is not an authorized repair service provider 3 When the product is used with the inapplicable cameras lens or adaptors or such accessories produced by the third party 4 Fault or defect caused by fire earthquake flood public pollution and such natural accidents 5 in the case that the product is stored in du
3. Nissin DIGITAL MARK I JiS66 PROFESSIONAL DIGITAL TTL POWER ZOOM FLASH INSTRUCTION MANUAL Type C NISSIN JAPAN Design and Specifications are subject to change without prior notice Nissin Nissin Japan Ltd Tokyo http www nissin japan com Nissin Marketing Ltd Hong Kong http www nissindigital com C0111 REV 1 2 Thank you for purchasing a Nissin product Before using this flash unit please read this instruction manual and refer your camera owner s manual carefully to get a better understanding of proper operation to enjoy flash photography Nissin Di866 Mark II type Canon is designed for Canon digital SLR with the latest TTL flash control system and features Nissin s original rotating color display easily guiding its operations It works automatically with Canon ETTL ETTL II auto flash systems Please note that Di866 Mark II type C is not usable with other branded cameras for TTL operation UNIQUE FUNCTION The color display automatically rotates to allow for easy operation in both the horizontal and vertical positions SIMPLE OPERATION When attaching Di866 Mark II to the camera the basic flash exposure operation is fully controlled by the camera It is the same idea as when you use the built in camera flash but it is placed on the hotshoe of the camera instead of using the built in flash ADVANCED FUNCTIONS Di866 Mark II provides many advanced flas
4. within the range of 3Ev You will get 3 continuous flash pictures in different exposure effects on each frame Set the camera shutter for drive mode and number of picture frame is to be set on the camera Refer the camera owner s manual for details On the TTL function screen press the button for 2 seconds TTL Advance page appears Select Bracketing by a button Select On for Bracketing by 4 button Select your favorite EV step from 0 3 to 3 for Bracketing by 4 gt button Press the button or wait for 8 seconds to return to the TTL function screen A BKT1 symbol appears at the upper right hand corner for Bracketing Remark IMAGE ZONE QJ Full Auto D Portrait A Landscape 4 Close up e e N 5 amp Sports Bj Night Portrait When setting the camera mode to any fay those image zone Di866 Mark Il is automatically set at TTL AUTO function mode In this mode TTL exposure level compensation can not be adjusted All other advance functions are available 16 Manual Power Opertion The mode to be set on the camera M or Av Flash Power can be adjusted manually The photographer can set the desired exposure manually by the most appropriate power in combination with the aperture value set on the camera 22 different power from full power to 1 128 power by every 1 3 stops are available Set the camera mode to M Jor Av on your camera Set the mode of Di866 Mark I
5. EV Zoom 11 12 Select lt q the compensation value you desire TTL and set 3 EV 1 3 To keep this value on your flash press on off switch to lock Press it again to release the lock 24mm Take a picture and the aimed subject is shown with required a lighting effect by keeping the exposure level of background as originally expected On some cameras the TTL flash exposure compensation can be set on the camera When the flash exposure compensation is set on the flash unit this value is to be counted in addition to the compensation value you set on the camera The display screen of the flash unit however shows the exposure compensation value set on the flash unit Set the camera s mode select the flash exposure compensation value and take pictures Almost all jobs are automatically done by the camera with such compensation of the flash exposure value and you just manually control the camera only 13 An ADVANCED CUSTOM SETTING enables you to enjoy creative flash photography For advanced flash photography the following five functions can be set on your flash Sub Flash Function Di866 Mark II provides an extra small flash below the main flash This small flash gives a fill in light while bouncing the main flash Bouncing the light may shadow the underside of face and this fill in flash brightens up the shadow On the TTL function screen press the set button for 2 seconds TTL Advance
6. and Power off timer can be set 5 5 seconds with fresh alkaline batteries for full power ETTL ETTL II for Canon digital SLR cameras Automatic exposure metering by external photo sensor Manual exposure Power ratio available Ref G No table Effective range of approx 0 7 to 10m 5600 K at full power flash 1 300 seconds full power flash 1 300 1 30 000 seconds controlled fl 12 3 to 33 ft lash FP flash for high speed synchronization Wireless TTL off camera flash system Wireless Master mode Wireless Remote mode Slave flash function at external auto exposure Slave to digital pre flash system Slave to traditional single flash sytem Service socket for the external power pack optional accessory Nissin Power Power Pack PS300 Canon Power Assist Pack CP E4 For firmware update service USB cord is not included Camera s hot shoe ETTL for Canon system Traditional sync System X terminal socket 74 x 134 x 110mm 29 2 x 53 x 43 5 inch 380g 13 40z 38 Guide Number and Flash duration table Guide No at manual exposure mode ISO 100 in meters feet Flash Power Level Zoom position Full 1 2 1 4 1 8 1 16 1 32 1 64 24mm 34 22 16 11 8 5 5 4 28mm 36 25 18 12 5 9 6 5 4 5 35mm 40 28 20 14 10 7 5 50mm 46 32 23 16 11 5 8 55 70mm 52 36 26 18 13 9 6 5 85mm 54 38 27 19 13 5 9 5 rd 105mm 60 42 30 21 15 105 7 5 Flash 1 600 1 900 1 1500 1 3200 1 5000 1 9000 1 15000 Duration second 1 128 2 5
7. be set and controlled in 3 different groups A B and C group 4 channels are prepared for signal transmission between the Master flash and the Remote flash Available combination of flash models and cameras Wireless TTL Flash Pairing Chart Master flash Group Setting Remote flash Nissin Di866 Nissin Di866 Mark II Pe l Canon 580EX Pe Nissin Di966 Canon 580EXIL Nissin Di866 Mark II A B Nissin Di622 Mark II ilt i AB C Canon 420EX Builtin Camerafash Wireless TTL ONLY Canon 60D Canon 7D Canon 430EXT Canon 430EX a co I r 4 Canon 580EXI MR 14ExX Ring flash Canon 5B0EX At SEG Commande A B MR 14EX ST E2 not supported Ais equivalent to Canon master flash system A B C mode 25 Remote flash Slave flash There is no limit of the number of slave flashes to set at one time It is however recommended to set maximum 3 pcs in one group as it may cause interference between flashes depending on the photographic conditions Use a flash stand to set the slave flash The stand provides the flash shoe and can stay either on the flat surface or be placed on the tripod or light stand by the screw provided at the bottom When setting Di866 Mark II to slave flash it is recommended to cancel the auto off setting or set it to 60 minutes at the Custom Settings Ref page 33 Refer your flash instruction manual for this function which may differ according to the flash model
8. directly at the driver of automobiles or such vehicles Do not set the flash window close to the human body and shoot which may get burned Place the batteries correctly in position Placing the batteries in wrong polarity may cause leakage exothermic heat or explosion A C This sign refers the damage or defect Do not leave or store the flash unit in the temperature over 40 C such as in the automobile The flash unit is not water resistance Keep the unit away from rain snow and humidity Do not use benzene thinner or other alcoholic agents to clean the unit Do not use this flash unit with the cameras which are not recommended in compatibility list at official website otherwise it may damage the camera s circuitry Remove the batteries when not in use for a longer period of time Do not have a heavy impact to the flash unit nor throw it onto a hard surface floor When using the external power pack read the safety instructions carefully and follow the operation manual menclature Light diffusing panel a ee Fill in reflector aaa X terminal Flash head USB service port Wireless transmitter External service Sub Flash box Remote Slave sensor AF assist light Power Pack socket External auto exposure sensor Lock ring Mounting foot Hotshoe contacts Foot lock pin Rotating display screen Multifunction button Set button Select button amp V
9. of custom settings enable you to customize your Di866 Mark II From 6 icons select lt gt amp Custom setting mode and set e Select S the item to be customized and set 4 gt the value to customize 9 custom settings are prepared SETTING AM My TTL TTL Exposure level custom setting TTL exposure level is accurately calibrated for standard balance in accordance with Nissin s standard If any adjustment is however required or if you like to set your own preferable level it can be adjusted for about 3Ev by g Display every 1 3 steps O meter Modeling Illuminating the subject to find its lighting efficiency A short pulse of flash light released by the test button illuminates the subjects and monitors the lighting efficiency on the subject Display Display can be set off if it s not necessary To save battery energy or imply to avoid the display illumination the display screen can be switched off when not in operation Set it off and the display goes off in 8 seconds after the last operation The display will not be woken up by the camera s shutter release The display can only be woken up by the operation button of Di866 Mark II Rotate Cancel the rotating action and keep the image fixed The screen won t rotate ft meter For the user who prefer distance indication by feet Select ft instead of meter 33 Auto Off Auto off timing can be selected from 10min 15min 30min 45min 60m
10. 0 8 8 8 8 8 8 1 32 60 60 50 40 30 25 20 12 12 12 12 12 12 1 64 90 90 80 70 50 35 25 20 20 20 20 20 20 1 128 90 90 80 70 50 35 25 20 20 20 20 20 20 When using an external power pack you may take continuous frames of multi exposure pictures Do not repeat multiple flash more than 10 continuous frames Take an interval of 10 to 15 minutes between shots Flash source may be heated up and may cause serious damage to the flash unit Please note that the basic operation is however controlled by the main batteries battery magazine in the flash unit and when the main batteries are exhausted flash control system does not work Replace the batteries when recycle time becomes longer than 20 seconds by main batteries only ref External Power Pack page 36 24 Q The mode to be set on the camera O Full Auto P Program Tv Shutter priority Av Aperture priority M Manual Di866 Mark II provides two possibilities of off camera wireless remote flash system This page explains Wireless Remote flash system The other system universal slave flash system is prepared at M and Av mode Ref page 19 22 The flash unit placed on the camera connected by TTL off camera flash cord is called Master flash The master flash to be set is one unit only The flash unit placed off the camera is called Slave Flash Canon type Multiple number of flashes can
11. 1 r 3 lens until you will have returned to M Zoom Off on the TTL Tea Advanced page Ev Zoom 2nd rear curtain synchronization Flash usually synchronizes to the camera shutter when it opens 1st curtain sync For the slow shutter photography Di866 Mark II can be set the flash timing just before the shutter closes 2nd curtain sync By using this function a moving subject is imaged with such moving marks behind Refer the camera owner s manual for details On the TTL function screen press the Set button for 2 seconds TTL Advance page appears Select Curtain by button Select 2nd for 2nd Curtain Sync by 4 gt button Press the button or wait for 8 seconds to return to the TTL function screen A symbol gt gt gt appears at the upper right hand corner for 2nd Curtain Sync while no symbol appears for normal flash sync 1st curtain 15 Hi Speed Sync The flash of Di866 Mark II can be set for camera with higher shutter speeds up to 1 8000 second Onthe TTL function screen press the button for 2 seconds TTL Advance page appears Select Hi Speed by button Select On for High Speed Sync by 4 gt button Press the button or wait for 8 seconds to return to the TTL function screen Asymbol 4H appears at the upper right hand corner for High Speed Sync Flash Exposure Bracketing FEB Di866 Mark II supports exposure bracketing function at every 0 3Ev increment
12. I From the 6 icons screen select lt gt M Av and set Set Select q gt M and set Select q gt your desired power and set Q x The camera subject distance for the most proper exposure MEANEN is determined by the film speed ISO and the F stop set M Mode on the camera This distance is shown in the Manual function screen V The film speed information ISO is automatically transferred from the camera MANUAL Av The F stop you set on the camera is to be set maunally on the flash unit too To get the camera subject distance on the display screen F Stop setting is required Press set Set for 2 seconds the screen goes to the Advanced Function page Move cursor to F Stop line and continuously select lt q the same F Stop number you set on your camera Press on off switch to lock the value Press it again to release the lock The distance is automatically followed by changing the focal length and ISO sensitivity level on the camera or selecting another power level 17 As for the non dedicated or traditional type film M Advance ai A or cameras the film speed ISO information is not transferred from the camera In this case the film speed ISO is to be set on the flash unit to indicate the camera subject distance Move cursor Sto ISO line at Advanced function page and continuously select 4 the ISO value to which you set camera Press the set
13. button Or wait for 8 seconds to return to M function screen 18 ADVANCED CUSTOM SETTING Advanced custom setting is prepared in this mode Sub Flash Function page 14 Manual Zoom Setting page 15 Universal Slave Function page 19 Di866 Mark II has a universal wireless remote flash system as a slave unit You can enjoy creative flash photography with multiple lightings from the various directions 2 slave modes are provided in accordance with the flash system of the master flash Slave Digital SD for digital pre flash system and Slave Film SF for an analogue flash system are available SD In this mode Di866 Mark II synchronizes to pre flash system The master flash is to be set at TTL ETTL II mode SF In this mode Di866 Mark II synchronizes to the traditional single flash system The master flash is to be set at manual mode Studio strobe lighting system synchronizes to this mode This mode also responds to open flash and to traditional type flash units in the market How to find SD or SF Select SD on your slave flash and release your camera s shutter to flash your master flash The slave flash flashes if the Master flash is SD and does not flash if the Master flash is SF If your slave flash is set at SF it flashes against both of SF and SD flash system M___ Advance m Off To set Di866 Mark II to the salve function mode move cursor gt to Slave line at Advanced function page and continuously s
14. easily focus the subject in darkness Fill in reflector and Light diffusing panel built in For short distance or portrait flash photography the light should not be too sharp or too strong to the subject Use fill in reflector flash or diffuse the light If the subject is close within 2 meter turn the flash head 90 upward and pull out the fill in reflector as shown in the picture Take a picture as usual A blink of fill in flash freshens up the subject in natural image This small blink of flash is also useful when taking a picture of baby without scaring him Pull out the light diffusing panel and place it over the flash window as shown in the picture The diffusing panel softens the flash light and creates a lively color effect upon the subject Since the light diffusing panel expands the lighting area it covers the range of 18mm of focal length lens 35 Bounce Lighting When taking a picture of a baby or small children do not shoot the flash straight onto them Bounce the light off the ceiling or wall so that it won t scare them When pointing the flash to a subject in front of the wall it creates an unexpected sharp shadow on the wall which results in poor picture quality Bounce the light off the ceiling or wall to soften the light over the subject and the shadow fades out Turn the flash head upwards or sideway The wall or ceiling in this case should be flat surface and wh
15. elect 4 gt SD or SF in accordance with the HEE system of the master flash you set Press the set button or wait for 8 seconds to return to M function screen Setting of Master and Slave flash m Setting Master flash The master flash to be set is one unit only Place the master flash on the camera and switch it on and set to Manual function mode or set to the camera s built in flash on Make sure which mode you chose digital pre flash flash system or analogue flash system Setting Slave flash Di866 Mark II Multiple numbers of flashes can be set Switch oO slave 2 Di866 Mark II on and select the appropriate slave o O system either SD or SF SE slave 1 When flash is set to the slave function the red LED starts blinking every 2 seconds showing the slave function is in order Make sure the mode Camera with O master flash you set SD or SF which should couple with the master flash system Set slave flash at any place and direct the flash head as you desire Slave sensor in the slave flash is facing to the camera or to the master flash Use the included flash stand Place Di866 Mark II on to the flash stand which can be placed either on a flat place or on the tripod by the screw Metal type accessory shoe is not recommended since it may give electric damage on the electrical contact of the flash hotshoe When setting Di866 Mark II to the slave function the zoom setting syste
16. er Inthe Master page Navigate the cursor and adjust the value according to the instruction at the bottom bar lt gt w Cursor Navigation 4 gt Value Adjust Channel Select Select Channel Ch1 Ch2 Ch3 amp Ch4 Zoom Select Select Zoom Mode Auto 24mm 28mm 35mm 50mm 70mm 85mm 105mm e Group Setting Value Adjustment a erias Ev compensation at TTL mode 7 a a3 f as 3 0Ev to 3 0Ev Group Power Ratio at M mode B GroupB 1 tay 1 2 1 4 1 8 1 16 C Group C Flash Mode 1 32 1 64 1 128 TTL TTL Mode M Manual Mode Flash off 27 Single Group Slave Flash Group A Setting 1 Navigate the cursor to Group A 2 Navigate the cursor to Flash mode and select mode TTL or M Selecting TTL 1 Navigate the cursor to the Value Adjustment and set the EV compensation level 2 Navigate the cursor to M Master 3 Select TTL or flash off in the Flash Mode 4 When TTL mode selected move the cursor to the Value Adjustment and set the EV compensation level 5 Navigate the cursor to M Master 6 Select TTL or FLASH OFF in the Flash Mode 7 When TTL mode selected Navigate the cursor to the Flash Adjustment and set the power ratio Selecting M 1 Navigate the cursor to the Flash Adjustment and set the power ratio 2 Navigate the cursor to M Master 3 Select M or FLASH OFF in the Flash Mode 4 When M mode selected navigate the cursor to the Flash Adjustmen
17. et out from the power ratio combination When TTL Mode selected in Group A amp B 1 Navigate the cursor to GROUP C and select TTL in the Flash Mode Navigate the cursor to Flash Adjustment and select the EV compensation Navigate the cursor to M Master Select TTL or flash off in the Flash Mode When TTL mode selected navigate the cursor to the Flash Adjustment and GY ng set the EV Compensation When M Mode selected in Group A amp B 1 Navigate the cursor to GROUP C and select M in the Flash Adjustment 2 Navigate the cursor to Flash Adjustment and select the power ratio 3 Navigate the cursor to M Master 29 4 Select M or flash off in the Flash Mode 5 When M mode selected navigate the cursor to the Flash Adjustment and set the power ratio AThis 3 group slave flash technology is recommended to shade off or remove the shadow behind subject which may be caused by the lighting produced by Group A and or B 30 Setting the Slave flash Channel Group and the flash reflector zooming position are to be set on the Remote flash TTL and Manual mode is available on Remote Flash which can however only be set by the Master flash j A From the 6 icons screen select 4 gt gt Q and set Select gt Rand set Q AF assist light starts blinking M every 2 seconds showing Di866 Mark II stands by in A TL hy Remote Flash mode g AOL Select vd the line channel and set 4 gt the cha
18. evel frequency and the number of flashes are to be set on the flash unit in advance Power Ratio Uncontrolled manual power is provided in 5 steps from 1 8 to 1 128 power Frequency 1 Hz to 90 Hz frequency can be set Flash Times 1 time to 90 times can be set Set the camera mode to M on your camera Set the shutter speed on your camera in accordance with the guide table in the next page Set the mode on Di866 Mark II From the 6 icons screen select q gt 444 and set e Value setting screen will appear with the default values a preset as shown A Trl Av In this mode the reflector zooming function is automatically set for option Either Auto zoom or Manual zoom setting is selectable Select the function and choose 4 the desired value one by one Press on off switch to lock this condition MULTI Or press set or wait for 8 seconds to return the multi flash function screen The use of tripod is recommended for this flash mode 23 Dora The shutter speed to be set on the camera is calculated in the following formula Number of flashes Frequency Shutter Speed Example To get 20 flashes at 10Hz gt 20 10 2 The shutter speed to be set on the camera is 2 seconds or longer Shutter for bulb setting is also available Guide Table for the number of flashes H Pa t 2 3 4 5 6 7 8 9 10 11 12 14 15 19 20 50 51 90 1 8 14 14 12 10 8 6 5 4 4 4 4 4 4 1 16 30 30 30 20 20 20 1
19. h functions Wireless TTL off camera flash technology high speed shutter synchronization frequent repeat flash system External Av priority setting etc are supported Compatible cameras Please refer Nissin s compatibility chart shown in its home page for details http www nissin japan com or http www nissindigital com AFETY INSTRUCTIONS These safety instructions refer to important information on how to use this product safely and properly Please read the following instructions before using the product A Ce This sign refers the danger or serious damage The flash unit contains high voltage electric parts Do not try to open or repair the flash unit Return it back to the repair service station or the store you bought it from Do not touch the inside parts from the opening when the unit was dropped or broken Do not shoot the flash directly to the eye at short distance It may damage the eye When taking a flash picture especially toward a baby it is recommended to keep the flash unit at least 1 meter 3 3feet away from the subject Or use diffuser or bounce the light to the ceiling or to the wall to soften its intensity Do not place the flash unit near any flammable gas chemical or such liquids It may cause fire or electric shock Do not touch the flash unit with wet hands or use in the water The flash unit carries high voltage inside and it may cause an electric shock Do not shoot the flash unit
20. he jobs required for this mode are completed When the pilot lamp turns green press the shutter button of your camera halfway to focus the subject Shutter speed aperture and flash mark 4 are shown in camera s view finder and the display panel of the camera Press the shutter and Di866 Mark II is fired The result is immediately shown on the camera s LCD monitor Flash power is automatically controlled by the camera and the most proper exposure is obtained on your picture When you change the focal length of your camera lens Di866 Mark II responds without delay and sets its light source for the proper illumination angle 10 The lens focal length you set is shown in the display screen of the flash unit The flash illumination coverage of Di866 Mark II responds to the lens focal length of 24mm to 105mm full size format film camera standard Set the camera s mode select the focal length and take pictures with Di866 Mark II on your camera Di866 Mark II is a supplement to help you taking a creative and live picture While you are taking pictures in Full Automatic mode almost all jobs are automatically done by the camera and you just control the camera only Mode Shutter Speed Aperture Setting Control on the camera 0O Automatic Automatic Automatic P Automatic Automatic Automatic TTL TTL Flash Exposure Value Compensation With the latest TTL flash control system the flash po
21. idle use on the camera or after the last setting is made To save the battery energy you can select the display off setting from the custom setting In this case the display screen turns off in about 8 seconds of idle use While Di866 Mark II is in the stand by mode display screen turns off and the pilot lamp blinks every 2 seconds showing the flash unit is in stand by mode To turn on Di866 Mark II again press the camera s shutter button halfway or press any button of the flash unit 2 Incase the Di866 Mark II is not in use over 30 minutes the unit is completely turned off To turn on Di866 Mark II again take the first step of turning the flash unit on In case of using Di866 Mark II in off camera use mode Wireless TTL flash slave Universal Slave function it is recommended to change the turn off timer at the Custom setting ref page 33 The mode and the value set on the flash unit before turning off is memorized and returns in the same condition when switch it on again Mounting Di866 Mark II on the Camera Turn off the power switch of both Di866 Mark II and the camera N Turn the lock ring of Di866 Mark II to loosen it all the way as shown in the picture 9 Slide the mounting foot of Di866 Mark II into the hotshoe of the camera 4 Turn the lock ring to opposite direction and tighten it a Lock pin comes out to hook the foot at the hotshoe for sure contact Rem
22. in or off cancel Firmware A firmware upgrade service is available for the Di866 Mark II which provides a USB service terminal By local service local dealer to upload the latest software Reset All the customs setting are reset to the default value and conditions which are 30 mini provided and set at the factory Bi set to confirm Buzzer This is available for Wireless Remote mode When using Di866 Mark II as a slave remote flash a beep sound indicates the master flash has triggered successfully Those customized value and conditions are effective on all modes and memorized even when the flash unit is switched off To reset the customized value or conditions select S Reset choose Yes and set All the memorized data is cancelled and Di866 Mark II is reset to the default value and condition Functions by Camera setting You do not need to set the flash unit for these functions F E Lock Di866 Mark II offers this function at A and TTL mode Focus the main subject and press lt gt button on the camera or lt FEL gt button on some cameras Exposure value on the main subject is memorized in the flash Aim the viewfinder center over the main subject and release the shutter 34 OTHER FEATURE AF assist light emitter Under the low light condition or in a dark place AF assist light will automatically emitt the red colored beam and illuminate the subject so that the camera can
23. ite color is preferable Colored ceiling or wall may reflect its color on the subject External Power Pack Socket When using an external power source the number of flashes is increased and the recycling time is shortened external power pack is available as an option The following Di866 Mark II is automatically turned off when repeating flash Battery NiMH battery Operation Modes Recycle time Nissin Power Pack PS 300 500 flashes 0 7 sec Canon CP E4 260 flashes 1 5 sec continuously over 20 to 30 times to protect the flash circuitry It will be automatically reset after 15minutes of stationary Please note that the basic operation is controlled by the main batteries battery magazine in the flash unit and when the main batteries are exhausted the flash control system does not work Replace the batteries when recycle time becomes longer than 20 seconds by main batteries only 36 USB Service Port Tired of your flash no longer working whenever a new camera comes onto the market A firmware upgrade service is available for the Di866 Mark II which provides a service terminal to upload the latest software A service charge for the firmware upgrade will be applied varying with different region Please check at your local dealer for details about the update service X terminal Di866 Mark II can be used with non hotshoe cameras Some cameras provide a fla
24. m is automatically set for the Manual Zoom at 24mm position The zooming position can be selected manually to any other position available In this mode the auto off timer is recommended to set at 60min or be cancelled off The sensing angle of the slave sensor is 100 approx 19 20 M F In this case reset this F Stop on you camera As for the traditional type eena no ISO information or F Stop information is transferred by the camera In this case set ISO value at the Themode ta be set ontheicamera TM tert Av Advanced function page of Di866 Mark II The flash light is automatically controlled by the photo sensor built in the flash Press set for 2 seconds the screen goes to the Advanced Function unit instead of TTL metering Select your desired F Stop on Di866 Mark II and page for Av mode set this F Stop on your camera The intensity of flash light is automatically controlled for the most proper exposure within the certain area of distance ADVANCEDCUSTOMSETTING gt Set the camera mode to M or Av on your camera PRATT Advanced custom setting is prepared in this mode Set the mode on Di866 Mark II From the 6 icons screen M Sub Flash Function page 14 select 4 gt M Av and set A TIL e Select gt Av and set hhh Q Q Manual Zoom Setting page 15 E Stop is displayed in the screen in accordance with the EEA ET page 19 ISO setting on the camera Manual Av e Select 4 gt you
25. nnel 4 r channels are available from 1 to 4 Wireless Select the line Group and set 4 the group 3 groups are available from A to C WIRELESS Remote Select the line Zoom and set 4 gt zooming position M R When setting Di866 Mark II to the Remote mode the Seto zoom setting system is automatically set at 24mm position The zooming position can be selected manually to any other available position Press on off switch to lock this condition Press it again to release the lock Or press set the screen shows the 6 icons screen and returns back to Remote setting page The function and the value remain recorded as set When placing more flashes repeat the same operation procedures instructed above The group can be chosen freely from A B or C but the channel of this bundle of wireless flash system is to be set in one common channel The flash mode and the value can not be set on the Remote flash but they are set by the Master flash only 31 SETTING THE SLAVE FLASH CREATIVE FLASH LIGHTING Set Master flash Set Slave flash flashes Make sure the channel and its group setting are correct Attach the Master flash to the camera and place the Slave flash flashes at any desirable place within the system operation area which is approximately 7 to 10 meters between the Master and Slave flash flashes depending on the setting condition 32 7 Custom settings A variety
26. oving Di866 Mark II from the Camera Loosen the lock ring and slide the mounting foot of Di866 Mark II off the hotshoe of the camera Make sure to turn the lock ring all the way to completely clear the lock pin off the hooking slot on the hotshoe Turn on the flash unit Press the on off switch Screen A appears and the mode A is set The pilot lamp blinks red showing the unit is charging In a few seconds the pilot lamp turns green The display screen automatically turns off in about 30 seconds after the setting job is terminated For a test flash press the pilot lamp To turn off the flash unit manually press the on off switch and hold it for 2 seconds SETTING THE MODE AND THE FUNCTION A The modes to be set on the camera O Full Auto P Program Tv Shutter priority Av Aperture priority M Manual ADEP Automatic depth of field D Portrait gj Landscape A Close up X Sports Night Portrait In all the camera modes listed above Di866 Mark II will automatically and fully work in ETTL ETTL II automatic flash control system Set Di866 Mark II to the camera s hotshoe and press the on off switch to power on Display screen automatically shows A the Full Automatic ae Mode Di866 Mark II is now set for the camera s automatic flash control system 24mm Press the on off switch once again to lock this condition on your flash Press it again to release the lock All t
27. page appears Select Subflash and continuously select 4 the power and set or wait for 8 seconds to returns to the TTL EV function screen 0 0 The following 8 powers are prepared in accordance with the photographic situation Subflash power Guide No at SO100 1 1 Full power 12 1 2 8 1 4 6 1 8 4 3 2 1 16 1 32 1 64 1 5 1 128 1 Hi Speed Bracketing This subflash function is available only at bounce photography and the mark SUB appears when tilting the flash head When the flash head is set at the normal position this mark disappears Manual Zoom Setting The reflector position of Di866 Mark II can be set manually To get an illumination area different from the picture frame either wider or narrower field manual zoom setting makes sense When using Di866 Mark II with non dedicated camera or traditional film type camera the reflector position of Di866 Mark II does not respond to the camera lens movement In this case use this Manual Zoom Setting On the TTL function screen press the set button Set for 2 TTL Advance seconds MZoom On TTLAdvance page appears Ast A ESTEEM Of Select SM Zoom and continuously select 4 gt on and set Set or wait for 8 seconds to returns to the TTL function screen Be aware that now your Di866 Mark II will not adjust the zoom ie EV setting automatically when you change the focal length of your
28. r desired F Stop and set Qon the flash In additional to the Manual power mode the universal slave function imit Av supports Av operation mode Press on off switch to lock the value Press it again to M Setting Slave flash Select the slave mode SD or SF and set the release the lock E desired F stop and ISO speed on the Slave flash As for setting Set the same F Stop on your camera AV Master flash follow to the instruction manual in the Universal slave The display screen shows the F Stop selected the F2 8 pagesat Manual power operation Page 13 camera subject maximum distance for the proper exposure and the focal length set on the camera sx Zim The flash light is automatically controlled within the distance area The shortest distance for the proper exposure is approximately 1 0m 3ft from the camera to the subject The distance varies by changing the focal length and F Stop set on Di866 Mark II This Av mode of Di866 Mark II is not coupled with camera s aperture setting The aperture setting on the flash unit is not controlled by the camera When changing the ISO setting on the camera the F Stop of the flash unit is automatically reset for such corresponding ISO value 21 22 Multiple Flash Mode Repeat flash Stroboscopic flash The mode to be set on the camera M Repeating the flash illumination on the subject freezes the sequence of motion in one frame of picture In this mode the power l
29. sh synchronization contact at x terminal instead of hotshoe For this type of cameras Di866 Mark II has a x terminal socket for flash synchronization A standard sync cable in the market is usable Off camera shoe cord Optional Di866 Mark II can be used together with Nissin SC 01 Off Camera Shoe Cord The cord provides a TTL hot shoe at main body It enable to attach two flash units on the top of camera and the off camera side at the same time Nissin SC 01 Shoe Cord Fig 1 Holding one flash unit by hand and set away from the camera Fig 2 Using 2 flashes together Itis not possible to shoot two flashes at the same time 37 SPECIFICATIONS Usable cameras Guide No Wattage Illumination coverage Power source Battery life Energy Saving Recycle timer Flash Exposure AF assist light Color Temperature Flash Duration Wireless flash External Power Pack USB service port Sync Contact Dimensions Weight Canon ETTL ETTL II flash system S LR and hotshoe type Compact digital cameras ref Nissin official website for camera models 60 198 at 105mm focal length ISO 100 m ft 40 132 at 35mm focal length ISO 100 m ft 83 Ws at full power 24 105mm 18mm with diffuser panel 4 x LR6 batteries Size AA Ni MH or lithium batteries usable built in 150 1500 flashes according to the mode with alkaline batteries Come to Stand by mode in 30 seconds
30. st moisture extremely high temperature or such poor conditions 6 Scratch blemish crush or worn out by a violently use or treatment 7 Guarantee card without the name of place purchased or the date of purchase stamped or no guarantee card 40
31. stop on the flash unit a a wr Multiple lighting exposes the playback photos in one frame of picture Q Wireless Remote Flash Mode page 25 Placing multiple numbers of flashes slave flash off camera and controlling the creative TTL lighting Variety of custom settings is available for own default value Manual Setting Mode page 17 Multi flash Mode page 23 Custom Setting Mode page 33 Flash exposure can be locked at the main subject while moving the framing Loc BASIC OPERATION Inserting batteries Usable batteries Alkaline batteries Lithium batteries NiMH batteries 1 Remove the battery magazine and insert 4 x size AA batteries as shown in the picture 2 The battery compartment is specially designed so that every cell is placed in the same direction to avoid the confusion in poor light condition 3 symbol is clearly marked at the battery compartment 4 Place the battery magazine back into the body When the recycle time becomes longer than 20 seconds replace the batteries with the fresh ones or recharge the batteries rechargeable batteries It is recommended to use all 4 batteries in same brand and type and replace them all at the same time Wrong insertion of each cell would not make electric contact Di866 Mark II has energy saving double power off function 1 The power is automatically turned off to stand by mode in about 30 seconds of
32. t and set the power ratio Note When setting FLASH OFF mode the master flash may flash when shutter released This flash is however the monitoring flash pre flash before the camera s shutter opens and is not be exposed in the actual picture Multiple Group Slave Flash Group B amp C Setting Group A MUST be set in order to add Group B Adding Group B When TTL mode selected in Group A i Navigate the cursor to GROUP B and select TTL in the operation mode box 28 2 Navigate the cursor to Flash Adjustment and select the power level ratio between Group A and Group B The power level ratio can be selected from 13 different combinations such as A B 8 1 5 6 1 4 1 2 8 1 2 1 1 4 1 1 1 1 1 4 1 2 1 2 8 1 4 1 5 6 and 1 8 3 Navigate the cursor to M Master 4 Select TTL or flash off in the Flash Mode 5 When TTL mode selected navigate the cursor to the Flash Adjustment and set the EV Compensation When M mode selected in Group A 1 Navigate the cursor to GROUP B and select M in the operation mode box Navigate the cursor to Flash Adjustment and select the power ratio Navigate the cursor to M Master Select M or flash off in the Flash Mode When M mode selected navigate the cursor to the Flash Adjustment OF PON and set the power ratio Adding Group C Group A amp B A B MUST be set in order to add Group C The group C is independently s
33. v Select button lt gt Pilot lamp Test flash button Flash stand Soft Case battery magazine optional 3 4 Di866 Mark II Flash Mode and Functions to be set on the flash unit Advanced functions are provided in some operation modes to be set on the flash unit A Full Automatic Mode Advanced Operation Modes Functions AUTO TTL TTL Program Mode r Sub Flash TTL Program Mode 1 Manual Setting Mode 1 M Manual Setting Mode Manual Zoom TTL Program Mode Manual Setting Mode Av Slave Function Manual Setting Mode 1 1 Multi flash Mode F Stop Setting 1 Manual Setting Mode ISO setting 2 Manual Setting Mode i Q Wireless Remote Flash Mode i 1 Effective on at Universal Slave function in Manual Power operation and when using Di866 Mark II with 2 Custom Setting Mode film type camera or with non dedicted camera 2 Effective on Universal Slave function and when using Di866 Mark II with film type camera or with non dedicated camera Full Automatic Mode page 10 Flash light is fully controlled by the camera for the most proper exposure Functions by Camera setting The flash is automatically controlled by the camera TTL Program Mode page 12 Flash light is automatically controlled by the camera but the flash exposure FE FE Lock page 34 value can be compensated S 8 6 Manual Mode Selecting the desired manual power on the flash unit Av poriority Mode Selecting the desired f
34. wer level is always automatically controlled by the camera for the most appropriate exposure You can soften or weaken the flash light or give more light to the subject without changing the environmental or background exposure effect The Di866 Mark II can possibly make it quicker control the flash output for each individual picture The modes to be set on camera O Full Auto P Program Tv Shutter priority Av Aperture priority M Manual ADEP Automatic depth of field e D Portrait 4 Landscape W Close up K Sports Night Portrait In all those camera s modes listed above Di866 Mark II will automatically Any available 5 1 Tv and fully work in ETTL ETTL II automatic flash control system I l Manual Automatic shutter speed can be set i 4 Any available Set Di866 Mark II to the camera s hotshoe and press the on off switch to Av Automatic Manual f stop can be set power on Warudi Any shutter speed Display screen shows A Press set and the display TTL M anpe Manual a i f stop combination can be set turns to the screen of 6 icons A TTL M e A Av Select TTL by select button lt gt S and set Or the display returns back to the A mode screen in about 8 Fahl Q y seconds The TTL flash exposure compensation value 0 0Ev is shown as a default setting EV TTL flash exposure compensation is provided in 19 steps 0 0 by 0 3Ev increment from 3 0 0 to 3 0Ev Bl race
Download Pdf Manuals
Related Search