AirLink ASW324V2 network switch
Contents
1. 3 j yE E E Zang ag peg my Desktops or Laptops Your network device i e computer switch IP Camera VoIP can be connected to any port of the Switch via a two pair UTP Category 5 Cable If the LED indicators do not light up after making a proper connection check your network device the cable the Switch conditions and connections Troubleshooting Power LED is not on Check if the power adapter is properly connected to the power outlet Make sure the power jack is firmly plugged into the power socket of the switch Link Activity is not lit when connect to 10 100Mbps device Made sure that the network device attached to the switch is turned ON Check the network cable make sure it is properly connected to the switch and the network device Check the network cable make sure the Ethernet cables comply with the specifications described in Section 2 Technical Specifications Standards e EEE 802 3 10BASE T IEEE 802 3u 100BASE TX IEEE 802 3x Flow Control and IEEE 802 3az EEE Energy Efficient Ethernet Network Cables e Ethernet 10Base T Cables 2 pair UTP Cat 3 4 5 Twisted Pair UTP Up to 100m e Fast Ethernet 100Base T 2 pair UTP Cat 5 Twisted Pair UTP Up to 100m Ports e 24x 10 100Mbps Auto Negotiation RJ45 Port Access Method e CSMA CD Transmission Method e Store and Forward Data Transfer Rate e Ethernet 10 20Mbps Half Fu2. Quick Installation Guide 24 Port 10 100Mbps Green Switch Model ASW324v2 Ver 1A Trademarks Copyright 2011 Airlink101 Airlink101 is a registered trademark All other trademarks belong to their respective proprietors Copyright Statement No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from Phoebe Micro Inc Preface FCC Warning This device has been tested and found to comply with limits for Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the user s manual may cause interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures introduction Congratulations on your purchase of the 24 Port 10 100Mbps Green Switch It is an easy to install network switch which helps you to extend your network structure quickly and reliably The 24 Port 10 100Mbps Green Switch is designed for energy saving easy
3. Comprehensive LED indicators display the status of the Switch and the network see Section 1 2 3 1 2 2 Rear Panel 3 Do not cover or put anything on or surrounding the Switch while the Switch is operating 1 2 3 LED indicators information The front panel LEDs provide instant status feedback and help monitoring and troubleshooting when needed AT 24 Port 10 100Mbps Green Switch 1 1 2 3 4 5 6 7 8 9 10 11 12 OOOOOOO000 O O Omur OOOOOO00 O O O QOnttw OOOOOO O O O O O Oumar eWRO OOOO OO O O O O O Ornitoom 13 14 15 16 17 18 19 20 21 22 23 24 Figure 1 3 Front Panel View of the Switch e POWER Power Indicator power on e Port 1 24 10 100Mbps Status LEDs Eb cor sea Bimg OW No activities The port is pois on the transmitting Green 10 100Mbps orreceiving No link Ethernet data at network IEEE om seid mm O0 The PN respective port Is connected to MUN 10 100M Green the connected to the slow 10 100Mbps Ethernet Ethernet network network Installing the Switch The site where you place the Switch may greatly affect its performance 2 1 Installation Please follow the guidelines below to install the Switch e Please install the Switch in a fairly cool and dry place Please refer to the Technical Specifications for the acceptable temperature and humidity operatin
4. g ranges e Please install the Switch on a sturdy level surface that can support its weight e When connecting the power cord to the Switch and the power outlet the distance should be no more than 182cm e Please leave at least 10cm about 4 inches of space at the front and rear of the Switch for ventilation 2 2 Desktop or Shelf Installation When installing the Switch on the desktop or shelf please attach the rubber feet to the Switch Peel off the protective paper on the pads and attach them to the bottom of the owitch one at each corner 6 2 3 Rack Installation The Switch is rack mountable and can be installed on an EIA 11 inch equipment rack To do this first install the mounting brackets on the Switch s side panels one on each side secure them with the included screws and then use the screws provided with the equipment rack to mount the Switch 2 4 Power on the Switch The Switch has a universal power supply ranging from 100V to 240V AC 50 60Hz power source The AC power connector is located at the rear of the unit The Switch s power supply will adjust to the local power source automatically Connecting the Switch This section describes how to connect the Switch to your 10 100Mbps Ethernet network 24 port 10 1 OOMbps Network Network VoIP Green Switch Storage Cameras Cable DSL Modem if 7 il D il l ll ll 3 I ee JE el i i i
5. installation and high performance in an environment where network traffic and the number of users increase continuously You can add other Ethernet devices like computers IP cameras and Network Attached otorage NAS onto your network quickly and easily The Green EEE Energy Efficient Ethernet technology of ASW324v2 automatically reduces the power consumption when any connected port is detected inactive idle or cable unplugged and it intelligently allocates less power to any port that connects with an Ethernet cable shorter than 20m 66 ft Before you start installation please check the package contents Package Contents e 24 Port 10 100Mbps Green Switch Power Cord o e Quick Installation Guide e Brackets and Screws Hardware Description 1 1 Hardware Interface e 24 x Port 10 100Mbps auto negotiation RJ45 port e All ports support auto MDI MDIX no need to use cross over cables 1 2 Panel 1 2 1 Front Panel The front panel of the Switch consists of LED indicators and 24 10 100Mbps ports The figure below shows the front panel of the Switch 11 12 LNK ACT 10 100M L _ A A A Le 0 100M 13 14 15 16 17 18 19 20 21 22 23 24 Figure 1 1 Front Panel View of the Switch e 10 100Mbps Ports Port 1 24 These ports support 10 100Mbps and can operate in Half Full Duplex transfer modes These ports also support automatic MDI MDI X crossover detection offering true plug and play function e LED Indicators
6. ll Duplex e Fast Ethernet 100 200Mbps Half Full Duplex LED e Power Green e Link Activity Link Activity Green 10 100M Green Rack Mount e 11 Inch Rack Mountable with mounting kits Dimensions e 280mm x 165mm x 45mm LxWxH Weight e 1400g 3 Ib Physical and Environmental e Power Input 100 240V AC 50 60Hz e Operation Temperature 0 C 40 C 32 F 104 F e Storage Temperature 20 C 0 C 4 F 158 F e Humidity 5 90 RH non condensing Certification e FCC CE Technical Support E mail support airlink101 com Toll Free 1 888 746 3238 Web Site www airlink101 com Free Voice Technical Support is only available within the hardware warranty 1 Year Limited Warranty from the date of purchase Customer is required to provide invoice as purchase evidence Network conditions and environmental factors as well as network overhead can lower actual data throughput rate Copyright 2011 AirLink101 All rights reserved AirLink101 the stylized AirLink101 9 logo specific product designations and all other words and logos that are identified as trademarks and or service marks are unless noted otherwise the trademarks and service marks of AirLink101 All other product or service names are the property of their respective holders AirLink101 products are protected under numerous U S and foreign patents and pending applications mask work rights and copyrights 12
Download Pdf Manuals
Related Search