Pyle PMIR15
Contents
1. Setting the measuring functions The IR thermometerHT 280H can perform different measuring functions To access setup mode press the button SET when the thermometer is turned on button MEAS The SET button takes you to the next respective menu point and the button LASER changes MAA MIN the parameters The active function is displayed on the display Menu sequence MAX MIN Display of the minimum or maximum value MAX MIN Off no icon Orr Switching the temperature unit from Celsius C to Fahrenheit F and vice versa rr o ca Increasing the degree of emission E max 1 00 z Decreasing the degree of emission E min 0 10 Setting for permanent measuring lock icon OFF Measuring only takes place when the measuring button is depressed ON Permanent measuring is activated the device does not switch off after 12 s To deactivate this mode press the button Laser The castle icon goes off Raising the alarm level Lowering the alarm level Activating the temperature alarm OFF ON The measuring device emits a warning sound when exceeding the previously set alarm level Tips and information e The emission degree described the energy emission characteristics of a material The higher this value is the more radiation a material may emit thermal radiation Many materials have a value that is close to the preset value 0 95 of the IR thermome2. out of the reach of children Do not leave the batteries lying around in the open there is the risk of them being swallowed by children or domestic animals If swallowed consult a doctor immediately Make sure that the polarity is correct when inserting the batteries Remove the batteries when the device is not being used for long periods of time Leaking or damaged batteries can lead to caustic burning of the skin Therefore use suitable protective gloves Batteries must not be short circuited or thrown into fire There is a risk of explosion Never take the batteries apart Always exchange the complete set of batteries do not mix full batteries with empty half empty batteries Never use batteries and accumulators together e Open the battery compartment on the back of the IR thermometer by sliding it in the direction of the arrow e Insert two micro batteries AAA in the battery compartment observing the correct polarity You will find the corresponding illustration in the battery compartment e Close the battery compartment in reverse order e If the battery icon appears on the display exchange the batteries immediately to prevent false measuring results Initial operation Operating principle IR thermometers measure the surface temperatures of objects The device s sensor measures the emitted reflected and penetrated heat radiation of the object and converts this information into a temperature value Measuring temperat
3. Infrared Thermometer PMIR15 pyleaudio com Intended Use The product is battery operated and serves for contact free temperature measuring on objects or surfaces A laser point serves as aiming device The degree of emission can be modified for measuring different surfaces Diagnostic application for medical purposes is not admissible Do not use any other source of energy Please also heed the additional safety instructions in each chapter of these instructions Any use other than that described above is not permitted In addition this involves other risks such as e g eye injuries Safety Instructions and Hazard Warnings _ An exclamation mark in a triangle indicates important information in these operating instructions Please read the operating instructions through completely before putting the device into operation They contain important information for correct operation _ The warranty will be rendered invalid for damage caused due to non compliance with these operating instructions We shall not be liable for any consequential damage We shall not accept liability for damage to property or personal injury caused by improper handling or non compliance with the safety instructions The warranty will lapse in these cases e For safety and licensing reasons CE unauthorized conversion and or modification of the device is not permitted e Due to the principle related inaccuracy of IR temperature measuring the displayed and the actual te
4. lam TANG setae ene ets ahi ee tel ee ea Ge ae ee lO 2 ZO Ambient conditions Working temperature range ccceesseseeeesteseeessssssesssssseeeeess OC to 50 C Relative air humidity ccccccseeececcesseeeceeeeseeeseeeeeesseeseeeseas lt 80 non condensing
5. mperature may differ slightly Therefore this product may not be used for very exact temperature measuring e g boiling or melting points chemical reactions etc Do not expose the device to high temperatures strong vibrations or a high level of humidity e Never look into the laser beam and never point it at persons or animals Laser radiation may lead to eye or skin injuries e Do not point the laser beam on mirrors or other reflecting areas The uncontrolledly deflected beam could hit persons or animals e Keep the device and the batteries out of the reach of children They are not a toy e This product is equipped with a class 2 laser according to EN 60 825 1 Apart from a battery change the device may not be opened Setting or maintenance tasks must only be executed by a trained Achtung LASERSTRAHLUNG NICHT IN DEN STRAHL BLICKEN LASER KLASSE 2 Laserdiode Ausgangsleistung max 1 mW Wellenlange 630 670 nm EN 60 825 1 1994 A11 1996 A2 2001 A1 2002 Caution if operation settings or procedures others than described here in these instructions are used this could lead to a dangerous radiation exposition Description of Individual Parts 1 Output opening for the laser beam 2 IR Temperature sensor 3 SET button for mode setting 4 LC display LCD liquid crystal display 5 MEAS button for measuring 6 Hand Strap 7 _LASER UP DOWN button for changing the Inserting replacing the batteries _ Keep batteries
6. ter Metallic shiny surfaces have a lesser degree of emission than matte black surfaces Therefore the degree of emission must be preset accordingly In this case attaching an adhesive strip or lacquer with matte black paint if possible helps to be able to measure with the common emission degree of 0 95 e Measuring through a glass pane is not possible instead the temperature of the glass pane is displayed Maintenance and Cleaning Periodically check the technical safety of the device It can be assumed that risk free operation is no longer possible if e there is visible damage to the appliance or e the device has been stored under unfavourable conditions for a longer period of time Periodically clean the surface of the IR sensor with a clean soft brush and a vacuum cleaner The outside of the appliance should be cleaned with a clean dry cloth or brush only Do not use abrasive or chemical cleaning agents which could damage the housing or impair operation Never try to open the housing apart from the battery compartment Disposal of spent Accumulators Batteries The end user is legally obliged German battery law to return all used batteries Disposal in household waste is prohibited Batteries and accumulators containing hazardous substances are marked with the shown symbols indicating that they must not be disposed of in the household waste The heavy metals concerned are Cd cadmium Hg mercury Pb lead You can ret
7. ures Direct the opening of the IR sensor onto the object or surface to be measured and press MEAS 5 As long as the button is kept depressed the temperature is measured and displayed the display shows SCAN The last measured value is displayed on the LC display the display shows HOLD The IR thermometer shuts off automatically after approx 12 seconds Make sure that the surface to be measured is larger than the measuring spot The ratio of the distance to spot ratio D S is 6 1 with this IR thermometer This means that with a measuring distance of 60 cm the measuring spot has a diameter of approx 10 cm For exact measuring the measuring object should be at least twice as large as the measuring spot hold the IR thermometer closer to the measuring object if applicable The temperature displayed by the IR thermometer is the average temperature of this measuring spot Activating the laser A switchable laser enables the easier positioning of the measuring spot Make sure that the laser point is approx 16 mm away from the center of the measuring spot see sketch Turn the IR thermometer on button MEAS and briefly press the button LASER 6 A small laser icon appears on the display triangle with a sun icon Now the laser is activated automatically during measuring To turn the laser off press the button LASER 6 again and the laser icon on the display disappears again Distance D to Spot Size S
8. urn flat batteries rechargeable batteries free of charge to the collection points in your community our branches or anywhere else where batteries or rechargeable batteries are sold You will thus carry out your legal obligations and contribute to the protection of our environment Disposal Old electronic devices are valuable materials When the device has become unusable dispose of it in accordance with the current statutory regulations at your communal collection points Disposing of flat batteries accumulators in the household waste Is prohibited Technical Data Operating voltage ceeeeeeeeeeeeeeesseseeessttesessssssstessesssseeees amp VDC 2x micro batteries AAA Automatic SWitCh off cccceccessseeesssseessseessstesesssssessseeeees approximately 12 seconds LASEP ansiavuees dots teen a a a batt cnet IV GIS DIAY vaciees fads siento aes coer a a aaa OlO CIGhy LGD NV GIGING segivei A eee een ee RNa a eho AD OIOX 700 Dimensions LXWXH c ceeeeeceeeeeeetseeeeesteseeesttsseeeeeeee 94MM xX 51mm x 25mm Measuring data Measuring range scececceeeeeeesseesesessaesesessssessessssssssssssseseses OC to 280 C Display TESOIMION ee eee ee OIC Measuring accuracy at 18 C to 28 C eeeeeeeetteeeeeeeees 2 5 or 2 C Degree Of EMISSION cecceseeeeeseeeeesseessssseesstssesssseessseeees 0 10 to 1 00 digitally adjustable Ratio CISLANCC SO OL xtseccic es scence tected a a a O01 A
Download Pdf Manuals
Related Search