Suunto Bike POD
Contents
1. or Spd sens if your device has a serial number 50499999 or lower The message TURN ON NEW DEVICE is displayed 4 Insert the battery in the battery compartment and wait for acknowledgement 5 Your Suunto t3 or t4 will display Paired or if pairing failed return to the Pair a POD menu Your Suunto t6 will display either PAIRING COMPLETE or if pairing failed NO DEVICES FOUND within 30 seconds 6 If pairing is successful close the battery compartment cover If pairing fails remove the battery and repeat steps 2 5 If pairing still fails make sure that there are no active ANT transmitters such HR belts nearby and repeat steps 2 5 After successful pairing you can view speed and distance related information in the Speed Distance mode while on the move If you would like to use the Suunto t6 serial number 50499999 or lower simultaneously with both the Bike POD and the Foot POD Suunto offers a free update to the device at your nearest Suunto Service Center upon presenting the Bike POD proof of purchase and after paying the postal costs for sending it to the service center For information on Suunto Service Center locations visit www suunto com 2 2 INSTALLING AND REPLACING THE BATTERY 1 Open the battery compartment cover with a coin 2 If replacing the battery remove the old battery 3 Place the new battery into the battery compartment with the positive side facing up and close the cover NOTE R2. the force 4 Push the locking lever to the CLOSE position 5 In all cases make sure that the nut is sufficiently screwed on The end of the skewer should not be deeper than 2 mm 1 16 inch inside the nut N 45 6 Attach the holder for your Suunto wristop computer to the handle bar with the flat part facing up Place the Suunto t series wristop computer around it See the figure under point 5 in section 3 1 3 3 2 3 INSTALLING THE MAGNET MOUNT Position the magnet mount on a spoke so that it passes in front of one of the marks on the lever The magnet must be turned towards the Bike POD e Hub 1 Magnet 2 Bike POD 3 3 3 ACTIVATION AND DEACTIVATION Your Bike POD is activated automatically when the spoke magnet passes the Bike POD i e when the front wheel spins It stays active throughout the cycling trip and for half an hour after the Bike POD has stopped receiving readings from the magnet 3 4 CONNECTION To use your Bike POD you must establish a connection between it and your wristop computer This can be compared to listening to a radio To be able to receive the radio broadcast signal you need to switch the radio on Similarly for your wristop computer to be able to receive the signal from your Bike POD the devices must be connected You need to establish the connection every time you want to use your wristop computer with your Bike POD 1 Spin the front wheel so that the spoke magnet pa
3. APPENDICE BIJLAGE LIITE BILAGA Tire size ETRTO Taille de la roue ETRTO Reifengr Be ETRTO Tama o de neum tico ETRTO Misura dei copertoni OTECC Bandenmaat ETRTO Py r n koko ETRTO Tire size inches Taille de la roue pouces Reifengr Be Zoll Tama o de neum tico pulgadas Misura dei copertoni pollici Bandenmaat inch Py r n koko Circumference mm Circonf rence mm Umfang mm Circunferencia mm Circonferenza mm Wielomtre mm Ymp rysmitta mm Calibration factor Taux d talonnage Kalibrierungsfaktor Factor de calibraci n Fattore di taratura Kalibratiefactor Kalibrointikerroin Hjulstorlek ETRTO Hjulstorlek Omkrets mm Kalibreringsfaktor 44 288 14x 1 75 1055 0 515 40 330 16x 1 50 1185 0 578 47 305 16x 1 75 1195 0 583 40 355 18 x 1 50 1340 0 654 47 355 18 x 1 75 1350 0 659 47 406 20 x 1 75 1515 0 739 37 451 20 x 1 3 8 1615 0 788 37 484 22 x 1 3 8 1770 0 863 40 484 22 x 1 1 2 1785 0 871 25 507 24x1 1753 0 855 28 520 24 x 1 1 8 1795 0 876 32 547 24 x 1 1 4 1905 0 929 47 507 24 x 1 75 1890 0 922 54 507 24 x 2 00 1925 0 939 54 507 24 x 2 125 1965 0 959 22 559 26 x 7 8 1920 0 937 30 559 26 x 1 25 1953 0 953 28 584 26 x 1 1 8 1970 0 961 37 590 26 x 1 3 8 2068 1 009 37 584 26 x 1 1 2 2100 1 024 37 559 26 x 1 40 2005 0 97
4. 8 40 559 26 x 1 50 2010 0 980 44 559 26 x 1 75 2023 0 987 47 559 26 x 1 95 2050 1 000 50 559 26 x 2 00 2055 1 002 54 559 26x2 10 2068 1 009 54 559 26 x 2 125 2070 1 010 57 559 26 x 2 35 2083 1 016 75 559 26 x 3 00 2170 1 059 25 630 27x1 2145 1 046 25 630 27 x 1 1 8 2155 1 051 32 630 27 x 1 1 4 2161 1 054 37 630 27 x 1 3 8 2169 1 058 35 590 650 x 35A 2090 1 020 38 571 650 x 38A 2125 1 037 38 571 650 x 38B 2105 1 027 18 622 700 x 18C 2070 1 010 19 622 700 x 19C 2080 1 015 20 622 700 x 20C 2086 1 018 23 622 700 x 23C 2096 1 022 25 622 700 x 25C 2105 1 027 28 622 700 x 28C 2136 1 042 30 622 700 x 30C 2170 1 059 32 622 700 x 32C 2155 1 051 19 632 700C Tub 2130 1 039 35 622 700 x 35C 2168 1 058 38 622 700 x 38C 2180 1 063 40 622 700 x 40C 2200 1 073 www suunto com O Suunto Oy 10 2004 7 2006
5. SUUNTO BIKE POD USER S GUIDE SUUNTO CUSTOMER SERVICE CONTACTS Global Help Desk 358 2 284 11 60 Suunto USA Phone 1 800 543 9124 Canada Phone 1 800 776 7770 Suunto website www suunto com COPYRIGHT This publication and its contents are proprietary to Suunto Oy Suunto Wristop Computer Suunto Bike Pod Replacing Luck and their logos are registered or unregistered trademarks of Suunto Oy All rights reserved While we have taken great care to ensure that information contained in this documentation is both comprehensive and accurate no warranty of accuracy is expressed or implied Its content is subject to change at any time without notice 1 INTRODUCTION Suunto Bike POD is an accessory for your Suunto t3 Suunto t4 or Suunto t6 wristop computer Itis a light weight wireless speed and distance sensor that combines new speed and distance functions with the detailed heart rate analysis and training benefits of your wristop computer creating one of the most advanced cycling specific training tools available Suunto Bike POD measures your cycling speed and distance by calculating the relation between the circumference of your bicycle wheel and the speed at which it rotates Measurement is effortless and when properly calibrated also very accurate Suunto Bike POD adds new features to your Suunto t3 t4 or t6 wristop computer Once paired with the Bike POD the wristop computer displays your current speed the distance fr
6. aded in www suunto com O Suunto Oy 7 2006 6 2 TRADEMARK Suunto and Replacing Luck are registered trademarks of Suunto Oy Suunto t3 Suunto t4 Suunto t6 Suunto Bike POD Suunto Road Bike POD and other Suunto product feature and content names are registered or unregistered trademarks of Suunto Oy Other product and company names are trademarks of their respective owners 7 DISCLAIMERS 7 1 USER S RESPONSIBILITY This instrument is intended for recreational use only Suunto Bike POD must not be substituted for obtaining measurements that require professional or industrial precision 7 2 CE The CE mark is used to mark conformity with the European Union EMC directives 89 336 EEC and 99 5 EEC 7 3 ICES This Class B digital apparatus complies with Canadian ICES 003 7 4 FCC COMPLIANCE This device complies with Part 15 of the FCC limits for class B digital devices This eguipment generates uses and can radiate radio freguency energy and if not installed or used in accordance with the instructions may cause harmful interference to radio communications There is no guarantee that interference will not occur in a particular instance If this eguipment does cause harmful interference to other equipment try to correct the problem by relocating the equipment Consult an authorized Suunto dealer or other gualified service technician if you cannot correct the problem Operation is subject to the following conditions 1 This
7. anager software The software is included with Suunto t6 and is optional for Suunto t3 and Suunto t4 devices You can always download the latest version of the Suunto Training Manager free of charge from www suunto com 5 TECHNICAL SPECIFICATIONS Weight Universal Bike POD 18g 0 60z Including battery and magnet Road Bike POD 69g 2 40z Including skewer battery and magnet Adds approximately 10g 0 40z to your normal quick release Water resistance 10 m 33 ft Operating temperature 20 C to 60 C 5 F to 140 F User replaceable battery 3V CR2032 Transmission range up to 10 m 30 ft Accuracy When calibrated typically better than 1 Frequency 2 465 GHz ANT compatible Battery life up to 300 h at 20 C 68 F 6 INTELLECTUAL PROPERTY 6 1 COPYRIGHT This publication and its contents are proprietary to Suunto Oy and are intended solely for the use of its clients to obtain knowledge and information regarding the operation of Suunto products lts contents shall not be used or distributed for any other purpose and or otherwise communicated disclosed or reproduced without the prior written consent of Suunto Oy While we have taken great care to ensure that information contained in this documentation is both comprehensive and accurate no warranty of accuracy is expressed or implied lts content is subject to change at any time without notice The latest version of this documentation can always be downlo
8. device cannot cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Repairs should be made by authorized Suunto service personnel Unauthorized repairs will void warranty Tested to comply with FCC standards For home or office use FCC WARNING Changes or modifications not expressly approved by Suunto Oy could void your authority to operate this device under FCC regulations 7 5 LIMITS OF LIABILITY AND ISO 9001 COMPLIANCE If this product should fail due to defects in materials or workmanship Suunto Oy will at its sole option repair or replace it with new or rebuilt parts free of charge for two 2 years from the date of its purchase This warranty is only extended to the original purchaser and only covers failures due to defects in materials and workmanship that occur during normal use while in the period of the warranty lt does not cover battery battery replacement damage or failures resulting from accident misuse neglect mishandling alteration or modifications of the product or any failure caused by operation of the product outside the scope of its published specifications or any causes not covered by this warranty There are no express warranties except as listed above The client can exercise the right to repair under the warranty by contacting Suunto Oy s Customer Service department to obtain a repair authorization Suunto Oy and its s
9. e must go in its slot as far as possible 2 Place the Bike POD on the right blade of the fork the Bike POD must be pointing forward close the fixing collars without tightening them 3 Adjust the position of the Bike POD so the center of the magnet is aligned with one of the arrows on the Bike POD The distance between the magnet and the Bike POD must be less than 10 mm 4 Tighten the wire ties and cut them flush 5 Attach the holder for the wristop computer to the handle bar with the flat part facing up Place your Suunto wristop computer around it d 8 2 ATTACHING THE SUUNTO ROAD BIKE POD 3 2 1 CONTENT OF THE SUUNTO ROAD BIKE POD PACKAGE Road Bike POD consisting of a skewer 1 guick release lever 2 and nut 3 Magnet 4 Holder for the wristop computer 5 3 2 2 INSTALLING THE LOCKING LEVER BIKE POD 1 Fit the quick release lever to the hub with the lever to the left to the right when using disc brakes Close the lever taking care to position it horizontally towards the rear 45 Adjust the tension on the adjusting nut so that sufficient force is applied when the locking lever is moved to the CLOSE position consult your retailer 3 When the locking lever can be moved to the CLOSE position too easily the wheel is not held in place with sufficient force If this is the case put the locking lever in the OPEN position and tighten the adjusting nut to increase
10. eplace the battery with extreme care to ensure that your Bike POD remains water resistant Check the condition of the seal on the battery cover each time you change the battery and replace the battery cover if the seal is damaged Careless battery replacement may void the warranty NOTE To reduce the risk of fire or burns do not crush puncture or dispose of used batteries in fire or water The POD uses one CR2032 battery Only use this kind of battery Recycle or dispose of used batteries properly 3 USING YOUR BIKE POD There are two different Suunto Bike PODs available The universal Suunto Bike POD is ideal for all situations and attaches easily to all kinds of bikes The Suunto Road Bike POD has a guick release system and also fits on most kinds of bikes although it is especially valued as a road cycling Bike POD 8 1 ATTACHING THE UNIVERSAL SUUNTO BIKE POD 3 1 1 CONTENT OF THE UNIVERSAL SUUNTO BIKE POD PACKAGE Bike POD 1 Magnet 2 2 wire ties 3 Holder for the wristop computer 4 3 1 2 INSTALLING THE MAGNET BRACKET Place the magnet bracket on a spoke on the right side of the wheel The magnet must be turned towards the Bike POD O Note If you are using a wheel with extra flat spokes you need to cut the tabs on the magnet bracket beforehand 3 1 3 INSTALLING THE BIKE POD 1 Insert a wire tie into each slot designed for this purpose from the Bike POD side The head of the wire ti
11. ing the Bike POD using a known distance 1 In your Suunto t3 or Suunto t4 enter Training mode In your Suunto t6 select Connect in the Speed Distance menu Reset the distance measurement at the start line In your Suunto t3 or Suunto t4 press START STOP in Training mode In your Suunto t6 press START STOP in the Speed Distance mode Cover a known distance with your bike Press START STOP to stop the measurement Select Calibrate in the Speed Distance mode Select Bike POD and replace the measured distance with the correct distance 3 5 3 Calibrating the Bike POD using the calibration factor table You can also calibrate the Bike POD using the calibration factor table The data in the table comes from various tire manufacturers and the European Tire and Rim Technical Organisation Because of the differences in the tire pressure tread pattern and measurement methods the table is only indicative 1 Check your tire size and find the appropriate calibration factor in the table see Appendix 2 In the Speed Distance menu select Calibrate 3 Select Bike POD 4 Select Cal t6 only 5 Setthe correct calibration factor with UP DOWN NOOR ON Suunto t3 and Suunto t4 Suunto t6 4 SUUNTO TRAINING MANAGER SOFTWARE While using Suunto Bike POD the speed and distance data is recorded by your Suunto wristop computer This data can be displayed in graph form and analyzed in more detail with Suunto Training M
12. om start and the lap distance Furthermore it stores lap times automatically according to the distance set by the user gives alarms for too fast or too slow speed and offers a distance based interval training function NOTE The wristop computer functions related to the use of your Suunto Bike POD are explained in the individual Suunto t3 t4 and t6 instruction manuals You can download the latest version of the manuals at www suunto com training 2 BEFORE USE 2 1 PAIRING YOUR BIKE POD Before you can use your Suunto Bike POD you have to pair it with your Suunto wristop computer This process can be compared to the tuning of a radio To be able to listen to a specific radio station you have to tune the radio to the correct frequency Similarly to be able to use your Suunto wristop computer with a specific Bike POD you must pair them with each other This is only necessary when you use your Bike POD for the first time Te pair your Bike POD with your Suunto wristop computer Remove the Bike POD battery gt Short circuit the and metal plates in the battery compartment of the POD by connecting them with a metal instrument for example by touching them with a screwdriver knife or a paperclip 3 In your Suunto t3 or Suunto t4 go to Training mode settings and select Pair a POD and then Bike In your Suunto t6 go to the Training menu and select Pair and then Bike POD if your device has a serial number 50500000 or higher
13. sses the Bike POD 2 In your Suunto t6 select Connect in the Speed Distance menu In your Suunto t3 or Suunto t4 enter Training mode 3 Your wristop computer informs you when the Bike POD has been found Suunto t3 or Suunto t4 If the connection fails the message Searching disappears from the bottom row of the display and the selected shortcut returns In this case spin the front wheel again to ensure that the Bike POD is active and try again Suunto t6 If the connection fails NO DEVICES FOUND is displayed on the screen In this case spin the front wheel again to ensure that the Bike POD is active and try again 3 5 CALIBRATION Suunto Bike POD measures your bike s speed and distance from the rotation of the front wheel The wristop computer needs a specific calibration factor that takes the wheel size into consideration To define the exact calibration factor measure the tire circumference or calibrate your Bike POD using a known distance 3 5 1 Measuring the circumference manually 1 Set a measuring cord on the floor 2 Sit on your bike and ride along the cord so that the tires rotate fully at least once 3 Measure the covered distance with the accuracy of a millimeter 4 Divide the circumference by 2050 for example 2096 2050 1 022439 1 022 5 Set the calibration factor in your Suunto t series wristop computer See steps 2 to 5 in Section 3 5 3 for setting the calibration factor 3 5 2 Calibrat
14. ubsidiaries shall in no event be liable for any incidental or consequential damages arising from the use of or inability to use the product Suunto Oy and its subsidiaries do not assume any responsibility for losses or claims by third parties that may arise through the use of this device Suunto s Quality Assurance System is certified by Det Norske Veritas to be ISO 9001 compliant in all Suunto Oy s operations Quality Certificate No 96 HEL AQ 220 7 6 AFTER SALES SERVICE If a claim under warranty appears to be necessary return the product freight prepaid to your Suunto representative who is responsible for having your product repaired or replaced Include your name address proof of purchase and or service registration card as required in your country The claim will be honored and the product repaired or replaced at no charge and returned in what your Suunto representative determines a reasonable amount of time provided that all necessary parts are in stock All repairs that are not covered under the terms of this warranty will be made at the owner s expense This warranty is non transferable from the original owner You can locate your local Suunto representative at www suunto com 8 DISPOSAL OF THE DEVICE Please dispose of the device in an appropriate way treating it as electronic waste Do not throw it in the garbage If you wish you may return the device to your nearest Suunto representative APPENDIX ANNEXE ANHANG ANEXO
Download Pdf Manuals
Related Search