Hannspree SV19LMMB 18.5" HD-Ready LED TV
Contents
1. Select Channel Block to block desired channels e Select Parental Guidance to set Age Rating Press lt gt to adjust the value from 4 to 18 or to set as None Select Input Block to block desired input sources Set Auto Power Off to either On or Off 30 HANNSpree Select Set Password to change the password Set Password New Confirm is 7 Back Select Clear All to restore defaults for all parental settings Note Channel Block is only accessible in TV mode Picture Format selections include Auto Normal Zoom1 Zoom2 and Full Screen Please see below for details Auto Normal Zoom1 Zoom2 Full Screen Note The options available on the OSD may vary depending on the input signal source HANNSpree 31 3 6 Adjusting Eco Settings 1 Press MENU to enter the OSD Main Menu screen Press YW to select the Eco menu Press gt to enter the Eco menu 4 Press to adjust the options settings 5 Press MENU to return to the Eco menu e eee entry 6 Press EXIT to exit the OSD menu The Eco menu can be used to adjust the Off and On settings 32 HANNspree Troubleshooting Situation No picture and sound Solution Connect the power cord properly Check if the power LED is on or not Press on the control panel or remote control Press Input to cycle through connected v2. HANNSpree 5 3 Install the outdoor antenna away from power transmission lines to avoid possible danger Preface Thank you for purchasing a Hannspree Liquid Crystal Display Television LED LCD HDTV Your new TV will allow you to enjoy superior audio and video while enriching your lifestyle with advanced technology Please carefully read this manual in its entirety before setting up using or operating your TV To ensure the safe and correct installation and operations of the TV it is important that the safety and operation instructions in this manual are followed This instruction manual is designed to assist you in setting up and using the TV The information in this manual has been carefully checked for accuracy however no guarantee is given to the correctness of the contents The information in this manual is subject to change without notice To the extent allowed by applicable law Hannspree Inc Hannspree shall not be liable for direct indirect special exemplary incidental or consequential damages arising from any defect or omission in this manual even if advised of the possibility of such damages in advance Li Warranty and Service For complete warranty service information please refer to the Warranty Card enclosed with your TV 6 HANNSpree Copyright Copyright 2010 Hannspree Inc All rights reserved This manual is protected by copyright and distributed under licenses
3. HDMI inputs 3 2 and 2 2 pull down HDTV Component input 3D Comb Filter R L audio inputs HD ready TV PC line input 3D MA deinterlacing 3 5 mm stereo earphone Dynamic backlight control output Dynamic contrast AV Composite input Eco design SPDIF output digital audio Noise Reduction out On Screen Display OSD menu system USB Music photo and movie USB update firmware Note The supporting devices mentioned in this manual may vary on different models For more information please refer to the manufacturer s user manual or the Quick Start Guide of your TV model HANNSpree 1 1 1 5 Control Panel Description Button Function Power Press to turn the TV on or off Input source INPUT Press to select the proper input source Press to turn the on screen display OSD Menu MENU menu on off Press to increase the program number or Program select PA move upward to the previous item on the OSD menu Press to decrease the program number or Program select P V move downward to the next item on the OSD menu Press to increase the volume or move to the Volume adjust VOLS right on the OSD menu Press to decrease the volume or move to the volume adjusl VOL left on the OSD menu ers Receive incoming remote control commands sensor 9 Power Standby Indicate power or standby status The LED indicator turns white when the device is turned on Spe
4. 3 4 Adjusting TV Settings 1 Press INPUT and select TV as the signal type in Press MENU to enter the OSD Main Menu 2 Seg pee screen N Channels Press to select the TV menu Press gt to enter the TV menu Press A to select an item Se Gee Geet oak O Press lt gt to adjust the scales or options settings N Press EXIT to return to the TV menu entry 8 Press EXIT to exit the OSD menu The TV menu can be used to adjust the Tuner Mode Country and Channels settings Tuner Mode can be set to Antenna and Cable Country can be set to Austria Belgium Bulgaria Croatia Czech Republic Denmark Finland France Germany Greece Hungary Iceland Ireland Italy Luxembourg Netherlands Norway Poland Portugal Romania Russia Serbia Slovakia Slovenia Spain Sweden Switzerland Turkey UK Ukraine and Other Channels can be used to perform or adjust the Channel Scan Update Scan Single RF Scan Analogue Manual Scan Favourite Network Select Channel Skip Channel Sort Channel Edit Decoder Analogue Ch Fine Tune and Clean Channel List settings 26 HANNSpree Select Channel Scan to activate the automatic TV channel search Channels Channel Scan Channel Scan 1 Status Scanning Update Scan i Analog Channels 0 Digital Channels 0 Single RF Scan Me p pa Analogue Manual Scan i 1 Channel Skip ui Channel Sort M Channel Edit H Scan 2 gt
5. Connect an HDMI equipment or an HDMI 3 Input C HDMI DVI adapter cable to devices such POS as a DVD player or set top box SPDIF Connect to a digital audio output device SPDIF such as a home theater AC IN Power Connector Connect to the included power cord 1 7 Remote Control Description Icon Function Power l Press to turn the TV on or off inb t Signal Press to select the input signal type selections Ka 9 INPUT TV YPbPr AV SCART PC HDMI 1 HDMI 2 yp and USB 123 Use to select a program directly Press 0 9 to Keypad 3 2 S enter the program numbers press 1 and 0 for o program 10 Pro List Pro LIST Press to display the programs contained 1 4 HANNSpree Description Icon Function LAST Last C Press to return to the last channel selected Information INFO Press to display current channel program information Press to turn the on screen display OSD Menu MENU menu on off OK OK Press to confirm selection Arrows ve gt Press up down left or right to scroll through the on screen display menus Electronic 3 Press to display detailed programming Program EPG f information for channels only for DTV Guide Teletext mode TEXT Press to activate teletext P Press VOL to increase volume Volume adjust VOL VOL Press VOL to decrease volume MUTE Press to eliminate sound Press it again or Mute K press the volume adjust buttons to restore sou
6. Press to select an item a kho N Press EXIT to return to the Features menu entry 7 Press EXIT to exit the OSD menu HANNSpree 29 The Features menu can be used to adjust the Menu Language 4 3 Mode Picture Format Time Subtitle Teletext Language Common Interface OAD Parental Reset Default Auto Power Off and SW ver settings Menu Language can be used to change the on screen display OSD language 4 3 Mode can be used to adjust the display aspect ratio to 4 3 and 16 9 settings Time can be used to adjust the Time Zone Time and Sleep Timer settings Subtitle can be used to adjust the Analogue Subtitle 1st Subtitle 2nd Subtitle and Subtitle Type settings Teletext Language can be used to adjust the Digital Teletext Lang and Decode Page Lang settings Select Common Interface to view the Cl supplier information Select OAD to upgrade the software for the device Select Reset Default to restore all settings to the defaults Select SW Ver to view the current firmware version Select Parental to adjust Channel Block Parental Guidance Input Block Set Password and Clear All settings You will be prompted to enter the password before entering the Parental sub menu By default the password is 1234 Parental Parental Channel Block 1i Parental Guidance j Input Block M Set Password Ji Clear All Password EXT Back Enter gt Select EXTBack
7. Select EMT Back Cancel Select Update Scan to automatically add channels to the existing channel list Select Single RF Scan to search for digital channels within the selected RF Radio Frequency channel Single RF Scan a Scan single RF channel Digital Only 0 RF Channel 5 4 BIA Signal strength 100 Scan Back Select Analogue Manual Scan to search for analog channels within the specified frequency range Analogue Manual Scan Search for analogue channels Start Frequency MHz E Scan Up i Scan Down MWe Back Select Favourite Network Select to select your favourite TV channels from the existing channel list HANNSpree 27 Use Channel Skip to prevent the desired channels from being accessed Press PA PV on the remote control or PA PY on the control panel Select Channel Sort to change the order of the channel list Channel Edit allows you to adjust the detailed items including Channel Number Channel Name Frequency Colour System and Sound System for each Channel Skip Analogue Analogue Analogue Analogue Analogue Analogue Analogue Analogue Og R N a o000 Set lt gt Select Back channel Channels Channel Edit Channel Scan m 2A Transmitter Update Scan u Channel Number F 4 E Single RF Scan m Chanel Name Analogue Manual Scan m Channel Skip M Chan
8. 1 Press d on the control panel or remote control The power LED turns white when the device is turned on 2 Press 4 again The power LED turns off when the device is turned off 2 3 2 Switching Source Signals Press INPUT on the control panel or remote control to select the incoming source signal 2 3 3 Performing an Automatic Channel Search Before using the TV to view programs you need to activate the channel search first 1 Press MENU on the control panel or remote control then select to enter the TV menu 2 Select Channels gt Channel Scan gt ATV only or ATV and DTV 3 Press gt on the remote control to run the channel search 2 3 4 Selecting Channels Press PA on the remote control or P A on the control panel to increase the channel number e Press PV on the remote control or P Won the control panel to decrease the channel number Enter the specific channel number by pressing the number buttons on the remote control 2 3 5 Adjusting the Volume 1 Press VOL on the control panel or remote control to increase the volume 2 Press VOL on the control panel or remote control to decrease the volume 3 Press MUTE to eliminate sounds and press MUTE again or press the volume buttons to restore the original volume 22 HANNSpree Adjusting On Screen Display OSD Settings The On Screen Display OSD menu system provides a quick and simple method to adjust the TV settings The OSD menu can be accessed conv
9. limitation not all of USB devices are able to be displayed properly e Operation using USB hubs is not guaranteed Due to the compatibility limitation not all of external hard disks are able to be detected correctly Cables used to prolong the USB device must be certified as USB 2 0 e In USB devices video files may not be played properly if speed is not enough HANNSpree 35 Specifications Model No SV19LMMB SV22LMMB SV25LMMB SV28LMMB SV32LMNB SV42LMNB DISPLAY Aspect Ratio 16 9 16 9 16 9 16 10 16 9 16 9 Resolution 1366 x 768 1920 x 1080 1920 x 1080 1920 x 1200 1920 x 1080 1920 x 1080 OSD Language Bulgarian Croatian Czech Danish Dutch English Estonia Finnish French German Greek Hungarian Italian Irish Latvian Lithuanian Norwegian Polish Portuguese Romanian Russian Serbian Slovak Slovenian Spanish Swedish Turkish Ukrainian ENHANCEMENT Sound Output RMS Watts 3W 3W 5W 5W 10 W 10 W Sound Mode Personal Music Speech Picture Format Auto Normal Zoom1 Zoom2 Full Screen Picture Mode Standard Vivid Movie Eco Personal CONNECTION Tuner Input 75 Q PC IN D SUB and PC Audio Component Video and L R Audio Input Rear Connector SCART 1 SCART 1 SCART 1 SCART 1 SCART 1 SCART 1 SCART 2 SCART 2 SPDIF SPDIF SPDIF SPDIF SPDIF SPDIF HDMI 1 H
10. DMI 1 HDMI 1 HDMI 1 HDMI 1 HDMI 1 HDMI 2 HDMI 2 Common Interface USB Earphone AV In Composite Audio Video Side Connector HDMI 2 HDMI 2 HDMI 2 HDMI 2 HDMI 3 HDMI 3 WEIGHT amp DIMENSIONS Product Dimensions mm 467 01 x 341 44 533 81 x 379 31 609 35 x 443 x 672 91 x 527 11 790 18 x 571 43 1021 1 x 705 8 WxHxD with x 148 x 148 210 x 220 x 240 x 270 stand Net Weight 3 74 kg 4 41 kg 6 kg 8 035 kg 13 kg 19 kg POWER Operation Max 26 W 30 W 36 W 55W 95 W 120 W Standby lt 0 5W a AC 220 240V Main Power 50 60 Hz Ambient 50C 35 C emperature 36 HANNSpree Dissembling the stand base 1 Disconnect all the cables and cords from the TV to prevent breakage 2 Carefully place the TV face down on a soft and flat surface blanket foam cloth etc to prevent any damage to the TV 3 Remove the screws so that the stand base can be removed 4 Gently remove the stand base 19 22 25 28 3242 For reference only Wall mounting the TV VESA compatible Mount holes Model Name wall bracket WxH Sumber Screw type Maximum loading SV19LMMB 100x100 mm 4 Metric 4 x 10 mm 15kg SV22LMMB 100x100 mm 4 Metric 4 x 10 mm 18 kg SV25LMMB 100x100 mm 4 Metric 4 x 10 mm 24 kg SV28LMMB 100x100 mm 4 Metric 4 x 10 mm 30 kg SV32LMNB 200x200 mm 4 Metric 4 x 14 mm 36 kg SV42LMNB 200x200 mm 4 Metric 6 x 12 mm 72 kg 1 Purchase a VESA compatible wall bracket please refe
11. Table of Contents Regulatory Information 2mmesmsinvisiir d RARA RA dd R n d 3 Description of Warning Symbols c c ci cici c ecc eeeeenee eed 3 Safety NOUCES iessen renr an rA ar AOO 4 PROTA CC nncneere a a aE E N E a 6 Warranty and Service 2144898324224222 nA AAE DEEA a 3 b 4 6 1 Getting Started essre Aar EEEa a ened EATER 8 1 1 Package Content 002060000020922040900G60600 036002640 A 00040 R 8 1 2 Stand Base AssemblYy icccicccciciccscecocacauooaasanaua 9 1 3 Introducing the TV 2220222220995424 ele de eed 11 1 4 Features ciarn Ta e ara aT ERONATE 11 1 5 Control Fanelli aeaa 12 1 6 Input and Output JackS icccccic cece eee e eee cii eeeeeeeenees 12 1 7 Remote Control ccccociicerririnccciesscccsereriseccinensircereninne renia 14 1 8 Inserting the Remote Control Batteries 18 2 Setting UP YOUR TV siscssiacesseredsecnswsseneiessededieedeaeteaedede 30 Cid 20 2 1 Power Connection 00 0 0 cee eeeeeee cence ee ee eee eee anae eaeeeenenes 20 2 2 Rear ConnectiONS cccccccccciciciccsciccccscicecocaaaosanaus 20 2 3 USING the TY scenari dives nia tinesdewtvettabe ve RA A Ce Ren ein 22 2 3 1 Turning the TV On and Off c c2cicocciiccminsimessesiies 22 2 3 2 Switching Source Signals 22 2 3 3 Performing an Automatic Channel Search 22 2 3 4 Selecting Channels cccceccccscococococooaonenaae 22 2 3 5 Adjus
12. XIT to return to the Picture menu entry 6 Press EXIT to exit the OSD menu The Picture menu can be used to adjust the Smart Picture Brightness Contrast Colour Tint Sharpness Colour Temperature Advanced Control and Advanced Video PC only settings Smart Picture can be set to Standard Vivid Movie Eco or Personal Brightness Contrast and Colour can be adjusted by pressing lt gt to move the scales from 0 to 100 Tint can be adjusted by pressing lt gt to move the scales from 32 to 32 Sharpness can be adjusted by pressing lt gt to move the scales from 0 to 7 Colour Temperature can be set to Normal Warm or Cool Advanced Control can be used to adjust the Noise Reduction Flesh Tone Backlight and X Contrast Noise Reduction can be set to Auto Off Low Medium or High Flesh Tone can be set to On or Off Backlight can be adjusted by pressing lt gt to adjust the scales from O to 100 X Contrast can be set to On or Off 24 HANNSpree Advanced Video can be used to adjust the Brightness Contrast Color Temperature and Advanced Video settings for PC mode Picture Brightness 100 Contrast 100 Colour Temperature Cool i gt gt Remove o select EXT Exit Note The options available on the OSD may vary depending on the input signal source 3 3 Adjusting Sound Settings 1 Press MENU to enter the OSD Main Menu screen Sound Sound Mod
13. akers Deliver high quality sounds 1 6 Input and Output Jacks Description Connector Function Cable Antenna Connect to an antenna or cable TV 1 2 HANNSpree Description Connector Function Earphone Output Connect to earphones or external p p Q speakers with built in amplifier Component CVBS Inputs Connect to an external device such as a Audio Nie Be VCR STB or a DVD player Component Connect to an external device such as a Inputs Video OTe VIDEO VCR STB or a DVD player PC Audio Input AUDIO Connect to a PC s line audio port Connect to an external device such as a SCART 1 N VCR STB or a DVD player with AV S t Video RGB L R IN Analog TV Out and if L R Out SCART 2 Connect to an external device such as a 32 42 only SS 44 4 scn CEE EEE VCR STB or a DVD player with AV S Video L R IN VGA PC Input Connect to a PC s VGA port USB Connect to a USB device USB Video VIDEO Connect to an external device such as a VCR STB or a DVD player Cl Connect to a Cl device HANNSpree 1 3 Description Connector Function Hom 1 Connect an HDMI equipment or an HDMI 1 Input HDMI DVI adapter cable to devices such SC as a DVD player or set top box Connect an HDMI equipment or an ane a Hami 2 D HDMI DVI adapter cable to devices such y as a DVD player or set top box
14. and old batteries or the life of the new batteries will be shortened Chemical fluids may leak from the old batteries Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type recommended by the equipment manufacturer Discard used batteries according to manufacturer s instructions Refer to your local recycling or waste disposal rules and contact a local waste disposal vendor to dispose of used batteries The remote control cover may have a magnet in it so do not place magnetic sensitive items such as watches credit cards or flash media close to the cover Do not use force when pulling the remote control cover open you may damage the hinge HANNSpree 1 9 A Setting up your TV 2 1 Power Connection 1 Connect the power cord to the AC IN input jack on the rear of the TV 2 Insert the plug at the other end of the power cord into a power outlet 2 2 Rear Connections See the illustration and table below for device connection instructions CI SLOT Cl based devices High quality speaker E N N tF Earphone Blu ray Disc it E player i j 2474444144 SCART2 Home theater gt VCR VCD DVD STB 4 gt gt FE Video Game Video Game Console Console TV cable antenna DVD pl
15. ayer lt VCR lt 20 HANNSpree No Connector Notes Instructions 1 AUDIO In The audio cable is optional 2 VGA e The VGA and audio cables are optional AUDIO In 3 HDMI 1 The HDMI cable is optional HDMI 2 When the HDMI to HDMI cable is connected connecting the audio cable is not necessary HDMI 3 However it s necessary to do so if a HDMI to DVI cable is connected 4 SPDIF The SPDIF cable is optional 5 Component The video and audio cables are optional Video Inputs Component Audio Inputs 6 SCART 1 If your AV devices are not equipped with SCART SCART 2 connectors you will also need a SCART adapter except for a SCART to SCART cable When a SCART adapter is used the S Video connector and AV connectors cannot be connected at the same time or the wrong signals might be generated The SCART to SCART cable and SCART adapter are optional 7 Cable Antenna If you cannot receive channels after connecting to a TV cable or antenna try scanning for channels 8 Earphone e The internal TV speakers will not output sound when a speaker or earphone is plugged in 9 Composite The video and audio cables are optional Video Input Composite Audio Inputs 10 Cl The Common Interface cable is optional Note The available connectors may vary depending on your TV model HANNSpree 21 2 3 Using the TV 2 3 1 Turning the TV On and Off
16. ce are trademarks or registered trademarks of HDMI Licensing LLC License Notice and Trademark Acknowledgment DE DOLBY Manufactured under license from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby EPAL PIUS DIGITAL PLUS Laboratories HANNSpree 7 Getting Started 1 1 Package Contents Make sure the following components are included in the box Please contact Hannspree Customer Service immediately if anything is missing or damaged e TV User s manual Quick start guide Warranty card Power cord Remote control and batteries TV cleaning cloth Stand screw x 3 for 19 22 Stand screws x 4 for 25 28 32 42 PG ME61 According to WEEE regulation this TV can t be handled as normal trash in Europe when it is out of usage Please refer to the recycle information from our website to handle it HE 8 HANNSpree 1 2 Stand Base Assembly SV19 SV22 1 Always assemble the TV base with assistance from another person 2 Lay the TV over a towel or cloth to prevent scratching to the frame or glass and place near the edge of a table 3 Follow the close up then place the base with the right direction Be certain to hold the TV firmly with your hand to avoid slipping Insert base then 3 screws provided and fasten securely Please fasten with cross screwdriver Always carry the TV with assistance from another person HANNS
17. e Personal i Equalizer 120Hz Equalizer 500Hz Equalizer 1 5KHz Equalizer 5KHz Equalizer 10KHz Balance Press to select the Sound menu Press gt to enter the Sound menu Press W to select an item QO O ro Virtual Surround ff i a FW N Press lt gt to adjust the scales or A gt gt Remove C Select EXT Exit options settings 6 Press EXIT to return to the Sound menu entry 7 Press EXIT to exit the OSD menu The Sound menu can be used to adjust the Sound Mode Equalizer 120Hz Equalizer 500Hz Equalizer 1 5KHz Equalizer 5KHz Equalizer 10KHz Balance Virtual Surround Digital Audio Out AVL Type and Audio Description settings Sound Mode can be set to Music Speech or Personal Equalizer 120Hz Equalizer 500Hz Equalizer 1 5KHz Equalizer 5KHz and Equalizer 10KHz can be adjusted by pressing lt gt to move the scales from 6 to 6 e Balance can be adjusted by pressing lt gt to move the scales from 50 to 50 Virtual Surround can be set to On or Off Digital Audio Out can be set to Dolby Digital PCM or Off HANNSpree 25 AVL can be set to On or Off Type can be set to Normal Hard of Hearing or Audio Description To adjust the Audio Description select Audio Description in the Type setting first Press lt gt to adjust the scales from 0 to 100 Note The options available on the OSD may vary depending on the input signal source
18. eniently through the buttons on the remote control Picture Smart Picture Standard Brightness 50 MAIN MENUS gt Contrast 52 Colour 59 Displays a list of Tint menus Sharpness 5 Colour Temperature Cool Advanced Control ADJUSTABLE Options INSTRUCTIONS Displays the setting value Quick instructions for of the adjustable options adjusting the settings Function TV Control Panel Remote Control OSD Menu MENU MENU Up PA Arrow Down P 7v Arrow V Select Increase VOL Arrow gt Select Decrease VOL Arrow lt Return MENU EXIT Exit MENU EXIT HANNSpree 23 3 1 OSD Setting Menus Follow the instructions indicated on the down side of the OSD Function Menu Press P P von the control panel or v arrow keys to scroll through the menus VOL on the control panel or the gt arrow key to select an item or MENU on the control panel or EXIT to exit the OSD menu The following menus can be set by different adjustment methods 3 2 Adjusting Picture Settings 1 Press MENU to enter the OSD Main Menu screen The Picture menu is displayed Picture Smart Picture Standard Brightness 50 Contrast 52 Colour 53 Tint 0 Sharpness 5 Colour Temperature Cool d Advanced Control 2 Press gt to enter the Picture menu 3 Press to select an item Press lt gt to adjust the scales or options settings gt gt Remove Select Exit 5 Press E
19. exit from the menu Freeze FREEZE Press to pause a video frame on screen 1 6 HANNSpree k Programmable in the TV source only Description Icon Function Press repeatedly to set the sleep timer Off j SLEEP 10Min 20Min 30Min 40Min 50Min ep une E 60Min 90Min or 120Min Cancel the timer by selecting the Off option ASPECT Press to adjust the width to height ratio of the Aspect ratio image with aspect ratio Auto Normal Zoom1 LH Zoom2 and Full Screen Note For best results use the remote control within a proper distance from the front of the TV Do not exceed an angle of 30 degrees when pointing at TV The operational distance may be shortened when the signal sensor is directly exposed to strong light Aim the transmitter on the remote control at the signal sensor and ensure that there are no obstacles between them HANNSpree 1 7 1 8 Inserting the Remote Control Batteries 1 Open the battery compartment cover at the back of the remote control A 2 Insert the batteries paying attention to the polarity markings inside the battery compartment B 1 8 HANNSpree A CAUTION If the remote control is not used for a long period remove the batteries and store them properly Handle damaged or leaking batteries carefully and wash hands with soap if they come in contact with leaked chemical fluids If your remote control has two batteries do not mix new
20. g to electrical equipment for use within certain voltage limits Hannspree cannot accept responsibility for any failure to satisfy the requirements resulting from a non recommended modification of the device Description of Warning Symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION This symbol is used to alert users This symbol is used to alert users to pay attention to important to the risk of electric shocks due descriptions regarding usage to dangerous and uninsulated maintenance repair and components additional important information related to this TV HANNSpree 3 Safety Notices Installation Safety Notes Location Avoid allowing the TV to get prolonged exposure to sunlight or other strong sources of heat Leave sufficient distance between the TV and the wall to provide enough space for the emission of heat AN WARNING To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus AN CAUTION These servicing instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so lt WARNING To prevent the spread of fire keep candles or other open flames away from this
21. ideo sources Press PA or P V to switch to other TV programs Make sure all cables are connected properly No picture or poor picture sound is OK Check the antenna and cable connections Adjust the Brightness in the Picture OSD menu Picture is not in color Adjust the Colour option in the Picture OSD menu Picture is OK no sound Make sure the source device is functioning properly Make sure the audio cable is connected securely Turn the mute off Press VOL on the control panel or remote control One of the speakers has no sound Adjust the Balance in the Sound OSD menu Cannot receive some TV channels using cable TV Try the Channel Scan function in the Channels OSD menu Want to reset TV settings Use the Reset Default function in the Features OSD menu Cannot operate menus If OSD items are colored in gray the system is in a state such that those settings are not available Screen image turns over Make sure the video signal cable is connected properly Snow appears on the screen Adjust the location of the antenna placing it far from roads or sources of interference Check the antenna and the video signal line connections Blurred or overlapped images Adjust the sharpness setting Choose programs with high quality signals Adjust the direction of the antenna or replace the video signal cable Remote control doesn t work Make sure the battery
22. is inserted correctly Replace the battery with a new one Make sure the TV power cord is plugged in Make sure the path between the remote control and the sensor is clear Try operating the remote control at a closer distance to the TV HANNSpree 33 Support Timing PC Mode Support Timing Mode Resolution paiar a T 1 640 x 480 31 469 59 94 2 800 x 600 35 156 56 25 3 800 x 600 37 879 60 317 4 1024 x 768 48 363 60 004 1280 x 720 44 772 59 855 6 1280 x 768 47 776 59 87 7 1360 x 768 47 72 59 799 8 1280 x 1024 63 981 60 02 9 1920 x 1080 66 587 60 Video Mode Support Timing Resolution active dot HDMI YPbPr 480i V 576i 480p 576p 720p 1080i lt lt lt lt lt lt 1080p 34 HANNSpree Support USB Compatible Formats USB Device Compatibility Device File Format USB 2 0 device USB memory USB card reader File System FAT FAT 32 Photo file format JPEG JPG PNG MPEG1 MP3 Bitrate 32k 64k 96k 128k 196k 256k 320kbps Music fonat Sampling frequency 32k 44 1k 48kHz MPEG1 2 AVI MPG MPEG TS Video file format MPEG4 AVI MP4 MOV MKV H 264 AVI MP4 MOV MKV TS Notes It does not support NTFS and the maximum file size of a single file is 4GB Progressive format jpeg files are not supported Due to the compatibility
23. nd muaroune l I Press to change the multi sound selection of d the TV channel Select PA PY Press P to increase the program number program Press PV to decrease the program number Red Green eo Oe Press the colored buttons to perform specific Yellow Blue tasks in the OSD menu or teletext mode HANNSpree 1 5 Description Icon Function Press to display a table of the available teletext Index INDEX subjects Programmable in the teletext mode only Press to display the teletext over the program 4 MIX Mix on the screen Programmable in the teletext L lt mode only Adjust size SIZE Press to adjust screen size Programmable in 4 the teletext mode only With an ATV source if teletext mode is activated and the teletext has a subtitle page Subtitle SUBTITLE press to display the subtitle page With a DTV source press to display the subtitle OSD and select the language Press to inactivate automatic page change Hold HOLD which only occurs when more than one teletext page exists Programmable in the teletext mode only REVEAL Press to display the hidden information such Reveal i as solutions to puzzles Programmable in the teletext mode only SOUND Press continuously to toggle through all the Sound Mode sound setting Personal Music or Speech Press continuously to toggle through all the Picture Mode PIC picture setting Vivid Movie Eco Personal ial Standard Exit EXIT Press to
24. nel Sort i Channel Edit m E Scan lt gt Select M Back J Set lt gt Select EM Back To change the channel number select Channel Number and use the number keys on the remote control to type numbers To change the channel name select Channel Name and use the number keys on the remote control to type letters digits or symbols Press keys repeatedly to toggle different characters 28 HANNSpree KEY CHARACTER o oOo NO a F O N O lt lt 7 VS lt M O PF N SAO ZA IMD ox Cw Or E T oN DO FF O DY Frequency displays the current channel frequency Colour System displays the type of current channel color system Sound System displays the type of current channel sound system Decoder supports the Canal paid TV channel with encrypted programs Select Analogue Ch Fine Tune to adjust precisely the analog channel frequency to ensure high signal quality Select Clean Channel List to delete all channels Note The TV Settings are only available in TV mode 3 5 Adjusting Features Settings _ Press MENU to enter the OSD Main Menu screen Features Menu Language English i 4 3 Mode 4 3 i Picture Format Auto i Press to select the Features menu i Time ile Sublitle Teletext Language i Common Interface OAD Press lt gt to change the options 2 Remove O Select EMEX settings Press gt to enter the Features menu
25. pree 9 SV25 SV28 SV32 SV42 1 Always assemble the TV base with assistance from another person 2 Lay the TV over a towel or cloth to prevent scratching to the frame or glass and place near the edge of a table 3 Follow the close up then place the base with the right direction Be certain to hold the TV firmly with your hand to avoid slipping 1 0 HANNSpree Insert base then 4 screws provided and fasten securely Please fasten with cross screwdriver Always carry the TV with assistance from another person 1 3 Introducing the TV You can watch Analog PAL SECAM Digital DVB T DVB C television channels and easily connect a VCR STB or DVD player to the SCART HDTV Component AV Composite and HDMI input ports location of these ports depends on model You can also use the TV as a monitor for your PC by connecting it through the VGA port Convenient control buttons located on the TV and a handy remote control let you change channels adjust the volume and change display settings through an easy to use on screen display menu system The built in stereo speakers provide full rich sound and a convenient audio output port lets you connect to an external audio system or earphones 1 4 Features TV Tuner Built in TV Tuner Teletext level 1 5 with 1000 pages Audio Video support memory SCART inputs Built in stereo speakers VGA PC input Image Enhancement Technology
26. product at all times 4 HANNSpree Notes The LED LCD HDTV is for entertainment use only and visual display tasks are excluded This device uses a VGA connector to connect to a PC To reduce the influence of main frequency on the source signal use a VGA monitor cable with ferrite shield Personal Safety 1 To avoid overloading the power supply never plug too many electrical devices into an outlet power strip or extension cable 2 Dangerous high voltage electric power components are located inside the TV To avoid electric shock do not disassemble the casing 3 Do not place or drop metals small objects or flammable materials into the vent of the TV 4 If the TV is dropped falls down or is otherwise damaged unplug the power cord immediately and contact an authorized service technician 5 If any fluid is sprayed or dropped into the TV contact an authorized service technician 6 The screen of the TV is made of glass Avoid hitting or scraping it If the screen is broken do not touch the broken glass 7 Do not allow children to use the TV unattended 8 Be careful when disconnecting the power plug Hold the plug Do not attempt to disconnect the plug by pulling on the power cord Installation 1 Do not place the TV in locations where there is excessive steam or dust 2 Avoid blocking the TV s vents do not place the TV on a bed sofa carpet or in a sealed cabinet
27. r to the table above S 2 Locate your ideal TV position on the wall HAnnspree 3 Fix the wall bracket firmly on the wall 4 Secure the TV to the bracket using the 4 mount holes on the back and center of the TV le Note Please read the instructions of your specific wall bracket to properly wall mount the TV The TV stand base can be screwed on a table or a hard surface using the hole on the back of the stand base Installing the LED LCD HDTV requires special skill that should only be performed by qualified service personnel Customers should not attempt to do the work themselves Hannspree bears no responsibility for improper mounting or mounting that results in accident or injury You can ask a qualified service personnel about using an optional bracket to mount the TV to the wall HANNSpree 37 Using the Cable Organizer Route the cables through the cable clamp as shown 38 HANNSpree
28. restricting its use copying and distribution No part of this manual may be reproduced in any form by any means without the prior written authorization of Hannspree The TV described in this manual may include copyrighted software of Hannspree or other third parties Hannspree or other third parties preserves the exclusive rights for copyrighted software such as the right to distribute or reproduce the copyrighted software Accordingly and to the extent allowed by applicable law any copyrighted software contained in the product described herein shall not be distributed modified reverse engineered or reproduced in any manner without the prior written authorization of Hannspree or of other third parties The Hannspree logos presented herein are trademarks of Hannspree All other product names trademarks or logos mentioned herein are used for identification purpose only and may be the trademarks or registered trademarks of their respective owners The purchase of the product described herein shall not be deemed to grant either directly or by implication estoppel or otherwise any license under the copyrights patents patent applications or trademarks of Hannspree except for the normal non exclusive use that arises by operation of law in the sale of a product Trademark Notice Hannspree products incorporate High Definition Multimedia HOM Interface HDMI technology HDMI the HDMI logo and High Definition Multimedia Interfa
29. ting the VOlUMEB cccciccccccicicsssccccscenanane 22 3 Adjusting On Screen Display OSD Settings 23 3 1 OSD Setting Menus serseri cece cece eee eee teeta bna Aven 24 3 2 Adjusting Picture SettingsS ccicococococcocononaaconanaa 24 3 3 Adjusting Sound Settings cicii cici cecs scene 25 3 4 Adjusting TV Settings icccici icis cecs escais 26 3 5 Adjusting Features SettingsS ciii 29 HANNSpree 1 Table of Contents OOAN ODO 3 6 Adjusting Eco Settings icccccciceciccccscacanasaa 32 lt Troubleshooting 2 cc2s ids neti ddsdict A N dde 33 Support TIMING cc ccc ccc ccc ee eee eee e eee ee ee ee ee eaeeeeeaeeeeeeeeeeees 34 Support USB Compatible Formats cc cece ee eeeeeeeeeee es 35 A Specifications craciciccninercivees ae B Ld aaa a a aa a Dc a 3260504 36 Dissembling the stand base cicccciciciccccicicecaccesaaa 37 Using the Cable Organizer ccccccciciciccscicacacaaaaaa 38 2 HANNspree Regulatory Information CE Conformity Statement This device is in conformity with the requirements of EU Council Directive 2004 108 EC on the approximation of the laws of the Member States relating to electromagnetic compatibility and Directive 2006 95 EC on the harmonization of the laws of Member States relatin
Download Pdf Manuals
Related Search